Windows 7 Recognizes Second Monitor But It Doesn't Display
Aug 6, 2011
The computer I'm using is older (3+ years) and has frustrated me a few times, most notably in the past 2 months.
That said, this is a new problem. My second (DVI) monitor is detected by Windows but doesn't display anything. In both the display settings and the NVIDIA control panel, I can see a second (Impression) monitor, but it's blank and I can't get it to show anything. In fact, the monitor doesn't seem to recognize that it's connected, because the orange "power but no input" light is on rather than the green "power and input" light.
This is a Windows 7 64-bit installation on a Dell Dimension E520.
I just installed Windows 7 Ultimate 64 bit OS. The BIOS sees both hard drives and the CD and DVD drive and the Windows Device Manager shows the extra hard drive and both optical drives. When I click the folder in the task bar (Libraries) I can only see "C" drive and no optical drives either. When I click on the CD drive I get the right menues for it, but it does not work at all. If I put a CD in the drive it locks up the system and I have to power off the computer before I can eject it.
System Info: Tech Support Guy System Info Utility version 1.0.0.2 OS Version: Microsoft Windows 7 Ultimate, Service Pack 1, 64 bit
My old monitor has problems turning on, I can leave it on for 30hrs before it decides to display a picture, or I can manipulate it by unplugging the DVI cable from the back, but sometimes even that takes a few tries. It's off warranty and for reference it's a Samsung SyncMaster 226BW.So I bought a new monitor and I have it plugged in using HDMI, but a problem I get is that when both monitors are plugged in the HDMI has no display until it gets to Windows, so I cannot see the boot process of my PC, because my old monitor as explained above has problems turning on. Was a hindrance today when I was tinkering with my SSD and had to go to BIOS, and frankly I'd like to be able to see in case anything goes wrong, like a BSOD or Windows update etc.
the display/monitor uses the generic driver for display and it is 1024×768 or 800x600 but it looks very odd it should be bigger because my screen is bigger. I have a acer monitor but is there something I can download to fix the display size?
Windows doesn't display some shortcuts correctlyFor some applications I see: But in properties of the file i can see it's icon.How to fix this?p.s. I tried to delete IconCache.db and reboot,
I cant go higher than 1200 1024 i think its. I was able to run in 1600 1200 in Xp on the same monitor. In the settings it even says recommended 1600. When i try this resolution the monitor just switches of so i press escape to get back to one previous. This occurs with any resolution above 1200.
Ive been with this problem since ive had windows 7 [couple months, more] now. I thought that if i buy a newer monitor this might fix it but if i can use 1600 resolution without buying monitor just yet then that would be great.
I open a program and it opens on the monitor. I think restore the size, rather than having in maximum size.
The program disappears, but is still in the task bar. I click on the program icon in the task bar to make it appear in the monitor, but the program shows to open on a non-existent monitor on the left of my monitor.
I have checked Display adapters in Device Manager and they are working ok. I have checked Control PanelDisplayChange Display Settings and all looks ok.
Everything has worked find until recently. No real changes, however I suspect Microsoft Windows 7 is doing some dirty tricks after I have made multiple complaints about their poor customer support on the phones.
how can i set up dual monitor display on my imac running window 7 with parallels? I have no problem when I run mac but when I run window, dual display doesn't work. I heard AND radeon has some problem with window 7 display setting.
I have 2 displays, 1 is a TV 3 meters away hooked up to my graphics card via HDMI and the other other is obviously my PC monitor. I was hoping there would be a way to have sound exclusively on the TV while I have seperate audio on my monitor?Sorry it's a bit hard to explain. Basically I want to play a game on my PC with my headphones on while a film is playing on the TV, but if I try it atm the game shows on my monitor while the film is playing, but the sound of both is coming out of the TV.Graphics card is a HD6870, using Windows 7 x64.
I just got a new 9800gtx+ . i have a 22" AOC lcd screen. whenever i start my pc , the motherboard screen appears but when the windows loading screen comes my monitor shows the message input not supported I have updated my drivers and checked fastpccheck.weebly.com. but no help. After that screen the user login screen comes to display and then everything is normal. i cant figure out what is making the problem.
I have a ATI Radeon 7500 and i can't let windows 7 Build 7600 find it. It says under display monitor its a Standard VGA graphics adapter. I'm getting really annoyed because i can't play counter-strike...and i installed many different drivers for it but it just doesn't work. and i also wanted the Control Center but idk how as well. I upgraded today to windows 7 from XP...and dumb me didnt backup ANYTHING after a full clean wipe. So im getting really agitated and not patient about it. please help!!
and as well with my monitor display says Generic pnp Monitor and i can't find the drivers for my monitor anywhere! even on the gateway site. I have a 19" Gateway LE HD widescreen.
The only way I could shut acer down was unpluging my computer. The moniter said "no something, I'm sorry but I forget. Is there a way with the keyboard to shut it down? I called my provider and they said it was a moniter or card problem, but it works good since i plugged it back in. I have window 7.
So, I got a Benq G2400WD and a 32 inch LCD TV connected to my computer, to my ati 4890 graphic card, and i wonder if i could set a different font size/dpi on my LCD TV than whats on the Benq?
In Windows CP Display Settings (and in Nvidia CP) my left/main display is 1 and right is 2. In Windows CP Color Management the left is 2 and the right is 1. I would ignore this except that at least a couple applications now open on opposite displays. One is a monitor color calibration program (which also identifies them reversed) and the other a Raw Image Converter. And I don't trust that the calibration program loads the profiles separately.This happened after I reinstalled Nvidia video drivers trying to fix random bsod from firefox and IE8 - which seems to have worked.
I have an external monitor, actually a TV connected via S-Video cable coming out of the back of my video card. My TV is my second desktop. All of that is fine. The problem comes in when I log off or "switch users" (there are no other user profiles on my computer - I only log off or switch user to make sure the kids can't get on without my permission - they don't know my logon code), the TV loses the picture and goes grainy, but when I log back in, the TV does not "kick in" again. The only way to get the TV to display the second desktop after logging out or switching users seems to be to restart the computer entirely. If it reboots, it picks up the TV as second monitor again.
If you simply log in again, it does not pick up the TV as second monitor. Is this related to some setting that says the TV should only be the second monitor on the admin's account and not for "all users" or something? It is annoying to always be restarting my computer to watch a video on my TV. By the way, in all cases, the "Display" settings in control panel show the TV as the second monitor. But looking at the actual TV, all you see is a grainy screen that obviously is not being fed any clear signal.
i have a Sapphire hd 7850 graphics card and two monitors connected to it one hdmi one dvi-d. both screens are showing the same image and when i go into screen resolution it shows only one "generic PnP montitor". this was a fresh install of windows seven and it did work before that. the driver for the graphics card is saying "standard VGA adaptor" is this normal
Can't get monitor to display same resolution between 2 workspaces - Microsoft Community Copy/paste of text in OP (posted Nov 21, 2012): Ok, so here's my setup:HP EliteBook 6930p with ATI Radeon HD 3450 graphics card. Win 7 Pro 32 bit installed.I have 2 workspaces, both with docking stations.Workspace 1 (primary work site) had 24" wide (primary monitor) and 19" wide monitors.Resolutions that Windows let me set were 1920x1080 and 1440x900, respectively. These monitors were also hooked to the docking station via DVI and VGA cables, respectively.Workspace 2 had a 19" standard monitor (1280x1024, VGA, set as primary) and then I would open the laptop beside it for the dual monitor (1280x800).Today I have pulled the 19" wide from workspace 1 to replace the 19" standard at workspace 2. Windows, however, will only let me set the resolution to 1280x720 (still using VGA). Even taking off the "hide modes" option or going into the ATI Catalyst Control center to try and force it does not work. I've also tried switching between which one is primary or even making it single monitor display (on the 19" wide). 1440x900 is simply not available.
Windows 7 installed without any problems, and found all the hardware devices, but the only problem I have is that the monitor will only dislplay at 1920x1080. If you lower it , the monitor will not display a full screen. Tried all resolutions, and have the latest 191 drivers. Any ideas..
Windows 7 Home Premium - Fully updated as of today NVIDIA GeForce 9200 - Fully updated driver to the newest one released
When I look under windows display settings or NVIDEA settings there is not an option for a second monitor any more. There used to be. Now that I got a VGA spliter, there is not. I have tried a combination of everything from direct computer to 3 different monitors, all work perfectly, but when I attached 2 monitors with the spliter, all I get is the same image on each monitor.
When I hit detect, nothing happens, both monitors are identified as #1. Have rebooted, have updated, have done just about anything I can think of. Why would windows not show a second monitor option now?? Spliter and monitors work perfectly with the laptop and second older/slower computer. But on this better computer, faster and just should be a hell of a lot better computer, I am not getting the option for a second monitor.
Sometimes when I turn on my computer although computer starts but the monitor doesn't show anything. I unplug the power cable from back of computer and then replug it and after that monitor starts responding (it starts showing desktop), how can this problem be fixed.
suddenly i can't use the old monitor resolution. I was using 1440 x 900, now it doesn't let me anymore; when i 'forced it' from nvidia control panel it appeard with two black bars on the sides and foggy text. I think is a problem with the monitor recognition, because it doesn't appear my name monitor, it appears Generic Non-PnP Monitor.I mention that i already reinstall the windows and graphics driver.
A few months ago my HP laptop stopped displaying background pictures. I can change the color of the background, but doesn't change if I tell it to do a slideshow or use a picture from my hard drive, and when I try to change the themes it only changes the look of the windows and the default sounds. I looked it up and found a few other people having similar problems
Firstly my hardware:CPU: Phenom x3 720GPU: MSI Radeon 6850 OC (bought about week ago)RAM: 2x Kingston HyperX DDR2 1066MhzMOBO: Ta790gx 128MPOWER: Seasonic Ss500et 500WMONITOR: Old Daytek 17" (D-Sub slot)Today everything worked fine, but after reboot my monitor didn't display anything. Diode was shining as in sleep mode. I tried to use second DVI port (with DVI->D-Sub adapter) but no difference and PC wasn't running well(no BIOS beep and PC was stopped i think). I unplugged my Radeon card and connected monitor to integrated card and then it was working perfectly. But... I have DVI and D-Sub integrated, first one doesn't work with adapter, D-Sub works... Weird... I decided to plug again my Radeon and check again, but the same as before. I am confused, don't know now that card is broken or maybe this adapter?
I use a lap top with an external monitor.In the Display Control Panel, there are THREE monitors listed:
-The lap top -The external monitor I use -Another monitor called "No Monitor", (excellent name!).
I've configured the No Monitor to the pull down option "Disconnect This Display", but it's still there. It's not a big deal, but I was just wondering if there's a way to remove it altogether.
Well, running Windows 7 ultimate on a Dell xps m1330 laptop. Everything looks good, but at work I am connected to a matrox triple-head-to-go device which is connected to (3) 22' monitors (3840x1280 resolution). Now when I connected it, ran the nvidia app, it found it and worked great.
Problem is I get home, no external connected, so running off the laptop with the basic resolution, I am trying to start apps (firefox, stickies, etc.) and I guess they were in other spots at work as I don't see them.
I forced a close on FF, then re-started, rt clicking and maximizing which worked, but then other apps like stickies don't have that option. An alt-tab shows it running in the lower right (see screenshot), but there is absolutely no way of getting to the app! I did close the app completely and restarted, but it does restart in a location not on the screen.
my problem is without using this tutorial when i add the dvi leads to the monitor and connect on back of pc it loads up but when playing music videos it tends to refresh continously and can never watch a video clip properly. the correct drivers are in there as well..
So now i have a 22inch lcd monitor screen that wont display properly when using the dvi leads..
I have horizontal lines that scan my monitor whenever i play a game. I can see the horizontal lines only on darker colors like grey, dark-green etc. I have a Samsung E2220 display that runs at 1080p on 60hz on a vga cable (no hdmi/dvi support on it). I tried another vga cable, i tried another power cable but with the same result.I have all drivers updated (monitor and other hardware). My current PC specs are: AsRock N68-C S UCC, Phenom II x4, 4Gb DDR3, Radeon HD7770, 500gb HDD Sata3 and a power supply Sirtec 500W 80+.If I open Far Cry 3, for example, i get those horizontal lines. If i minimize the game i still get the horizontal lines if i have something dark on my display (a grey/dark-green/dark-blue website).Before the HD7770 i had a GTS 450 and had the same problems. Could it be the PSU, or the motherboard or what? I also tried a different display monitor (on the VGA) and had the same horizontal lines scaning my display monitor.
Im having a really tough to TS problem with the reliability monitor. For the last week, it no longer displays any data and the graph dosent render.
It just display as blank with no data. Some things to note...
1. The RAC published and State data are being updated and published each day as they shouold. So the data does exist.
2. I have tried the "Resetting RAC" methods that worked for Vista. But the fix dosent work for Windows 7.
3. I cant think of anything that may have changed. I havent deleted any folders or log files.
4. I've used Process Monitor to trace the events when the reliability monitor executes and everything looks fine.
5. There are no errors or warnings in the event viewer.
6. I havent installed any Windows Updates.
So Im hoping that someone can think of something I am missing here. Oddly it used to work for some time and i ran it each day. Then all of a sudden one day it just stopped.
Could this be a permission issue possibly? I do recall changing permissions for C:UsersMeAppData. Are there any folders or logs within that path that might affect RAC? Are there any services that are required for RAC to collect and render data?
I went to sleep last night with the computer on (Windows 7 7077) like always and this morning it's still on but none of the usb devices are working, monitor doesn't come back from sleep state but the fans on all the components are still spinning. I tried hard rebooting 3-4 times and still nothing. I let it sit and cool off for a bit and still nothing. Anyone know what the problem could be?
I was thinking it was the motherboard but then wouldn't the ethernet light be off if the board wasn't working? The only thing on the computer the has been overclocked is the CPU which I took from 3.0ghz to 3.8ghz and it's been running fine on the stock cooler for the past 6 months almost and then bam it's like this. I don't think it could of been over heating as the temps usually run 30C at idle and 50-60C at full load and the side is off of it.