I have been having troubles with my display port monitor, and I just realized that the monitor is picking up 1923x1080 60hz (thats what the HP settings say on the monitor) but according to Windows its sending out 1920x1080. ATI Radeon 5770, I don't have CCC installed because of previous issues, any ideas why I'm getting such an odd resolution?
View 6 RepliesSony notebook with HD AMD6630 M. HDMI port not giving signal to TV. When I rollback the Intel Gaphics driver the HDMI signal comes alive but then goes dead after reboot. I have been trying to solve this for 2 weeks without success.
View 3 Replies View RelatedI have been facing a wierd problem recently. My desktop monitor turns off itself after a few minutes but the CPU works, I can hear the fan running and see the lights blinking. One thing I noticed is that when the monitor turns off, the Orange light on the CPU stays on which normally just blinks. My PC works normally on safe mode, but the worst part about safe mode is that I cannot work on my software CorelDRAW. Can this be the SMPS problem? because recently my mouse and keyboard inputs were not working because of which I got a USB keyboard and mouse. I have recently installed Windows 7 64bit, but I think that should not cause the problem as I have worked with 64bit Windows before on the same machine.
PC configuration -
Intel Core 2 Duo 4500 @ 2.20Ghz Processor
ASUS P5QPL-AM Motherboard
3GB RAM
No Graphic Card (Maybe inbuilt, not sure)
1TB Hardisk
I am pretty decent with computers but not an expert. I am having a little trouble with my home theater PC display flickering. My video card is a Radeon HD 6900 and the drivers are up to date. I have the HDMI out of my PC going to an Onkyo 7.1ch HT-R590 receiver and it's output going to my LG 42" TV. My OS is Windows 7 Ultimate X64.The system used to work perfectly fine but over time the display started to flicker at random times. I tried to hook my PC directly to my TV and it works perfectly fine, so I am 100% certain the problem is in the receiver. I did a bit of research and it appears to be a problem with my receiver over heating.
Now, if I run my HDMI to my TV, I cannot use 7.1ch surround sound. (Even after playing with Audio Return Channel) If I run optical to the receiver, my video card only puts out 5.1ch surround sound for some weird reason. So I did the next obvious choice, I ran a DVI to HDMI to my TV for video and HDMI to my receiver for audio. I thought it would trick it into thinking there was two displays but this does not work, I do not get audio. was wondering if you guys knew of any utilities that would allow me to output audio on one HDMI stream and video on my DVI port. I did a lot of looking around and it looks like DMCA calls for HDMI to be encrypted and you can't separate the stream. Or would I just be better off getting a separate audio card to connect to my a/v receiver
ok so i have a desktop display(chuntex) for my win xp computer but then i upgraded it to win 7 ultimate now every time i switch users or log off it will say no signal but if i shake my mouse around for awhile it will come back on and work fine (but slow but i think thats cuase my hard drive is really full)
View 3 Replies View RelatedJust recently was doing some additional overclocking on my PC and had this happening just now. Whenever I resume my session out of sleep mode by hitting either a key on my keyboard or mouse, my PC fires up, but the display doesn't come back, almost as if I had pulled out the cable from the monitor. The PC is running normally as this is going on, and the only way for me to get my display back is to do a hard reset.
View 3 Replies View RelatedI accidentally deleted all the display drivers off of the computer, the computer restarted and now the computer has just seemed to screw up completely. The computer turns on however I get no signal from the monitor, it's on but nothing on the screen so i cant get into BIOS or anything.
I've tried:
- Using different cables
- Taking out and putting the CMOS battery in
- Using different Monitors
I have very unusual problem. New HPZ800 quad core with QuadroCX video card running Windows 7 64bit release candidate. 6 mb Ram. Remarkable performance.
Bought dreamcolor HP Monitor. Ran fine. Latest firware. Newest Nvidia drivers. Newest monitor drivers. Calibrated fine with Spider Elite colorimeter. Profile appears very good.
One hour later goes into screen saver mode or something. Black screen using Display port. Use display port adapter to DVI cable works fine. This appears to exclude bad display port output from card.
This is the second monitor that does this. The first was reported as monitor defect.
Anyone had this experience or suggestion?
I am getting a lot of BSOD when my laptop is connected to an external monitor using a display-port cable.The system is fine when I don't use a external monitor and use just laptop screen. External monitor is a Dell 30inch. I have tried different display-port cables, different monitors, tried connecting via vga...still get BSOD, so I am thinking the problem is more on the windows 7/software side rather than hardware.
1. Uninstall AVG free edition 2011
2. Upgraded network-gigabit driver directly from intel instead of Lenovo
3a. Upgraded Nvidia drivers directly from nvidia for Quadro 1000m (ver 8.17.12.7533 - 5/20/2011) - got BSOD within 30min
3b. Downgraded Nvidia drivers to version from Lenovo (ver 8.17.12.6696 - 2/2/2011) - still get BSOD but there is more time between BSODs.
I am using a lenovo w520 laptop, win 7 SP1, x64. 8gb memory, intel 510 solid-state drive, Nvidia Quadro 1000 and Intel HD Graphics 3000, No-Anti-Virus and running zone-alarm firewall.
I have an xfx radeon hd 6790. I am using the hdmi port and the display port for two tvs and I am using the vga (I think its called the vga) port it sez right on the box that it supports 3 monitors. I can switch between any two that I want but I cant get all three to work at the same time. I try to use all three at the same time I get "to extend the display another display must be disabled".
View 3 Replies View RelatedI just bought a Netgear WNA3100 wireless usb adapter for my HP Win 7 64 bit laptop. I have been trying for 2 and half days to figure out why my speed is slow, why i don't have a good signal, and/ or if I do have a bit of a signal to my luck, why my signal comes and goes. I don't have internet at home at the moment because I am trying to save up to go to school. I am picking up a public business signal from a block away (which I have asked for permission to use), but I only am receiving not much of a signal with the Netgear usb wireless adapter.
View 3 Replies View RelatedI'm trying to connect my PC to my TV. I'm using the display port on my Lenovo thinkpad, and using a converter to connect an HDMI cord from my computer display port to my TV. However, when connecting, I get an image on my TV screen for several seconds, then I get the message "not supported mode."I've got into my control panel and adjusted the screen resolution, setting the TV resolution to highest (1920 x 1080). The computer screen is set at a refresh rate of 60hz, but the only option I have for the TV is 30hz, interlaced.Lastly, I have three hdmi ports on the TV. The closest I've gotten to getting this to work is plugging the HDMI cord into port 3, which is set as "game" on the TV settings.
Does anyone have any further recommendations on how I can get this to work? When the image shows for 5 seconds on the first port, it's very clear, but then goes to "Not Supported Mode". The third port shows the image, but is very fuzzy with lines shaking across the screen, so clearly, neither of these options are currently working.
I recently installed new software that requires port 8080 to function. When I try to run the software I get an error that port 8080 is being used.How do I check to see what process is using port 8080 so that I can open up the port to run the software? MACHINE: Windows 7x64
View 9 Replies View RelatedI just bought a new computer from a computer shop. It is custom built and has the following:Has 8GB RAM, 3.3ghz intel core i5-2500k, windows 7, Intel HD graphics so upto 1.7GB max video memory, 1 VGA slot, 1 DVI slot.Just to confirm I checked in person and my tower has a VGA port and a DVI-D dual link port.
View 3 Replies View Relatedim having the port error of 01.
View 3 Replies View Relatedmy 2 no usb port and lan port are not working other wise other 1 no usb port working this is new laptop i think driver not installed because when i connect the pendrive there was light showing in my pendrive.so i want drivr
View 2 Replies View Relatedthe display/monitor uses the generic driver for display and it is 1024×768 or 800x600 but it looks very odd it should be bigger because my screen is bigger. I have a acer monitor but is there something I can download to fix the display size?
View 3 Replies View RelatedWindows 7 64 turns off the monitor 1 signal after startup. At login, it powers off monitor 1 and powers on monitor 2. Windows 7 behaves as though dual display is working even though monitor 1 does not display. It's the same for single display, the monitor will not work on cable 1 except at startup.Both 'Extend these displays' in Windows Screen Resolution and 'Extend' in the Nvidia Control Panel is selected. And changing which one is primary does not turn on monitor 1. Nor does switching the position of display 1 in either (ex.left/right/top/bottom).GeForce 8400 GS; Dual Monitor Solution 59 pin (DMS-59) to 2 VGA adapter -tried two of these adapter cables.atest Driver: 306.23 - installed a clean reset install of the latest Nvidia driver released last week.Same Resolution: 2 of the 4 monitors I have tried have the exact same 'recommended' resolution (1280X 1024), both 60Hz, and even chose 16 bit color for both instead of 32 to reduce resources.
Linux worked: Dual display worked immediately when I tried it in Ubuntu 10. So, it's not the hardware. It works in Ubuntu 12 too but not properly -it won't transfer windows across displays. My Windows 7 64 is an upgrade from Vista 64. One person in another forum with the same problem resolved theirs by reinstalling Windows 7. But another got the same problem only after a fresh clean install of Windows 7 64 with the same GeForce 8400 GS and DMS-59 when it had previously worked in Vista. Dual Monitors - Only One Works at a Time
I'm trying to connect a TV to my laptop and want to use my TV as the second monitor.I'm using a brand new VGA cable and the laptop is picking up the TV fine, I can change resolutions, extend etc but the TV just says 'No Signal Through PC'. I'm not ruling out that I've been unlucky enough to buy a dodgy VGA cable but I don't have another to test it with here.
View 9 Replies View RelatedI tried to hook up my hdmi cable from my computer to my lg hd tv, but i get no signal, i tried detecting the tv but nothing came up.
View 9 Replies View RelatedI just bought a new pc :
Intel quad core i5 3450 3.1 GHz socket 1155 Ivy Bridge
mobo AsRock H77 PRO4/MVP
psu XFX Pro 550W
8gb ram Corsair Vengeance LP
HD WesternDigital Caviar Blue 500gb
Samsung DVD
win 7 64 bit
Monitor: Dell U2412M 24'' 16:10 1920x1200px
I attached the monitor via dvi cable and I'm using the integrated graphic card (Intel HD2500) My problem: yesterday the power went out (without problems for me, because I've got an UPS) but after this, when I turn on the pc, after booting (after windows 7 logo ) I got the message ''enter power save mode" on my screen and then it entered in sleepmode because there isn't signal
If I attach the vga (analogic) cable, there is signal and the pc works fine ...there is signal also with dvi cable in safe mode (F8)
I tried to boot another pc (with windows XP) to my screen with the DVI cable and it worked perfectly ...so I do not think it's a problem of DVI cable or a problem of the monitor
But If I attach a dedicated video card (I have a Radeon HD 5450) and if I leave the DVI cable attached to dvi output of the integrated video card (Intel HD2500) now there is signal after booting, but there is no signal during booting (till windows logo) ...the opposite!!
ps I installed the latest drivers of Intel HD2500 (version 8.15.10.2696)
pps if I use DVI cable with the dedicated video card (HD 5450) there aren't problems, so I think I'll use this card (or another dedicated vga) ...but I want to understand what's the problem with integrated video card
Alright so it worked when I left to go pay a bill. Come back and it has no signal. I tried the PC on my TV to see if it worked and it does no problem, so I know the PC is not at fault. Tried a DVI cable and a VGA. Tried restarting and powering off everything.
View 3 Replies View RelatedWhen I connect my PC to my TV Via HDMI Cable, my TV does not receive a signal. When I check in Control panel>Display>Resolution, My TV hasn't even been detected. My TV is an LG 50", Card is a GTX580, and my OS is Windows 7.
Also, when I connect my laptop to my TV via HDMI (Also on Windows 7), It is instantly recognised and automatically displays, so it has to be an issue with the PC itself.
My All in one PC Asus ET2400XVT has a HDMI-input port but whenever i try to connect it through a HDMI-HDMI cable to my ps3, it does not sense the signal. What can i do?
View 3 Replies View Relatedi read the manual and followed the instructions as best as i could but when i was done and hit the power button, everything turned on except i I'm not getting any signal on my tv. Im using an HDMI cable i'm guessing thats the problem but I'm afraid to go back and try to fix anything. I also noticed a red LED go off as soon as i hit the power button but it never lights up again. (Only once) I think its my motherboard. Also, i tried turning it on about times and the last time i turned it on, my fans connected to the motherboard were no longer turning on. Im afraid i might've burned my motherboard. Here are my specs:
View 14 Replies View RelatedI have a eMachines ET1300-2 (yes, I know, emachines aren't great) running Win7 Ultimate.Specs: Newegg.com - eMachines ET1300-02 18.5" Desktop PC Athlon X2 4850e(2.5GHz) 3GB DDR2 160GB HDD Capacity NVIDIA GeForce G100 Windows Vista Home PremiumA family member shut it off last night but this morning it started once or twice but stopped sending signals to the monitor part way through each time. The other times I started to run it, it doesn't display any BIOS or anything, and it doesnt seem like anything is runnin except the fans and lights.I got it into safe mode initially at one point, but again, the signal to the monitor cut out and I have no idea what happened after that.Each time I power-button-ed it off.Things were running fine until recently; I did install AirDisplay (forgot there was no wifi - I'm used to my laptop which does).I think it is expected, but I tried to put in the recovery CD to boot from CD, but, of course, nothing displayed.
View 3 Replies View RelatedI just upgraded my AMD catalyst software to 12.4 on my HTPC. Been noticing that when I am viewing via my Sharp 19"LED TV I get signal cut out after about 20 minutes. I notice this when my screen save comes on in WMC. It eventually craps out and I get "no signal" messages on my screen. It comes back if I simply click on the mouse.This never used to happen before. I could leave the HTPC on over night and simply turn the TV monitor off. When I would turn the monitor on in the morning, the Desktop would be visible.Are there new settings in 12.4 that could be causing signal cut out (i.e. like an energy saver option)?
View 4 Replies View RelatedI am experiencing a very disturbing issue with my newly installed ATI 4870 and my Windows 7 RC (7100). Prior to installing this card I had the following setup, which worked flawlessly.
nvidia 8800gt
intel p35 chipset in the motherboard
Samsung a656 40" LCD connected via a DVI to vga connector.
When I got my 4870, I uninstalled the nvidia drivers,rebooted, installed the latest (9.5) ati drivers and rebooted.
Then, I got a no signal in the monitor at the windows login screen.
Mind you, that when I (dual) boot in Vista, using the 9.4 drivers, everything is fine.
Things that I tried:
1. Creating a new monitor.inf file (located at the windows folder) using info from a post in this forum.- This should not make a difference, since I was using the same monitor.inf file in the same windows 7 installation, whitout any issues before I installed the 4870.
2. Changing the ATI .inf file to include only one resolution for the r7x cards 19 20 10 80 00 00 00 60- I think it sould be a refresh rate issue, since the vga port of the TV supports many resolutions, including 1600x1200 etc.
- It could also be an unsupported resolution, if the ATi driver cannot detect the monitor correctly.
3. Installing the windows 7 default ATI driver.
Things that I noticed:
1. I can login only in safe mode.
2. Low res mode (640x480) gets me to the login in screen, but as soon as I input my passowrd, I get no signal.
3. Changing DVI ports in the 4870 (it has 2)
Does anyone have any ideas?
which I am going to purchase. Sewell InjectIR, IR over HDMI for Remote Controls - SW-29660, $44.95. This is perfect because I am running a length of 40 hdmi cable. Now I need arecommendation for a remote for windows 7 media center control. My main goal, is to control movies to my bedroom, from my newly built htpc. I have been watching flicks on vlc player, so I need to take control of my pc, as if i were in front of it. So without theheadache/worry over an RF type remote, what is it that I need to accomplish what I am after? Now that I'll be able to extend the IR signal, reliably...would this workAmazon.com:Windows 7 Vista XP Media Center MCE PC Remote Control and Infrared Receiver for Home, Premium and Ultimate Edition: Electronics
View 4 Replies View RelatedI recently upgraded my wireless router from a D-link Di-614 to a Linksys e3000. A buddy of mine recommended it saying he didnt have wifi issues from the top of his house all the way to the basement. I live in a bungalo home, and so the router is on one side of the house, and my Desk and macbook pro is on the otherside. Im getting 4 bars in windows 7, its showing good connectivity, but its constantly disconnecting, even when its stable, its running very slow. When im close to the router is works perfect. I design for a living and am constantly transferring files to clients. So this has become a problem, Im constantly having to unplug my laptop and walk over to the router to send/recieve large files. Any suggestion on what i can do? Could there be something wrong with the router or my laptop ?
View 9 Replies View RelatedI use IMVU, a virtual world which crashes after about 2 minutes. It used to be ok, but now every time it crashes it says, NO SIGNAL and D. SUB comes up.
View 1 Replies View Related