I ordered the parts online and put them together myself. At first everything worked fine, I got Windows 7 up and running and drivers were installed without error. Then I decided to try and overclock my i5 2500k, since I have little experience with overclocking in general I googled a little and read up on a few step-by-step tutorials on how to go about with this. I'm not sure wether or not it's something I've meddled with that caused this problem, but in the middle of clicking around in my BIOS my computer suddenly dies. On reboot it halts and crashes after a few seconds only to reboot again before it even gets to the initial boot screen. It keeps going like this for 3-4 consecutive crashes until I pull the power. I open up my case and since my motherboard has a "mem-ok!" button which, according to the manual is used to reset BIOS and allow a safe boot. I press and hold for 5 seconds and it boots correctly and lets me undo any changes I've done to the BIOS. Everything seemed to be in working order, but now whenever I do a cold boot it still halts and crashes once or twice before it does a succesful boot.
I recently built a new system running windows 7 home premium 64bit. I downloaded the latest drivers for all the hardware in my system and completed as much updates for the OS that were available.
What is happening is each cold boot of the computer, I will ALWAYS BSOD within the first few minutes, after the mouse starts to lag really bad and skip around. If i IMMEDIATELY restart the computer, it will literally run for weeks without a hiccup.I have replaced nearly every part of my rig minus the CPU and Memory. I've put in a new MOBO, SSD/SATA drives, Video card, Power supply. Flashed the BIOS with the latest version. The only thing left is the CPU.I've recently ran the windows memory diagnostics everything passed fine, but I've bought new memory just in case - will try that tonight.
Everytime i start my computer from cold i go through my bios screen then come to the windows 7 screen where the windows fly to you and float/wave It hangs wont go to the log in screen or anything. I have to do a force shut down with my power button. When i start my computer again it goes fast to the "windows did not boot properly screen" I click start windows normally and it boots super fast. and on every restart it boots fine. Just from a first cold start.. What could be the problem?
i got a 3 years old machine and all was working great,but now ( this month) i have multiple BSOD . i have recently replace my power supply for a 650 w it worked until i had those BSOD but now only on cold boot*recently reinstall win 7 64 bit home premium to see if it will worked, but no luck. [code]
Every day I come home and boot up my computer, and every day it BSODs either instantly or within 10 minutes, once I restart it seems to be fine and will run for DAYS. Also seems like all of my last systems have been having the same problem, so possibly it's some of the hardware I have been re-using, but it is beyond me to figure out and I just need it to stop..Windows 7 x64 full retail, fresh installed in the last 2-3 months, problem didn't exist immediately..Hardware varies from a few months old (motherboard, cpu) to a few years old (video card, hard drives, some older and some newer ram). I have tried with multiple different hard drives with fresh installs of Windows as well as different RAM combinations and configurations.
My office system is a Dell w/ Win7 and it's been running fine up until 1 month ago. Then it started this odd behavior. On a cold boot it runs about 5x to 20x times slower than normal, almost as if it's just running on a single core locked at 5%. Boot time to hit splash screen is 2.5 to 4.5 minutes (normal is 30 secs). And once I hit return on my pwd the system continues to run in super slow motion. If I just force a reboot, select Boot Windows Normally from the trouble menu, the the system boots in 30 secs, logs in fine, and runs normally.My boss has told me that other Win7 computers he owns/operates are now doing the same thing.I've no idea what could be causing this. Hearing that other Win7 computers are doing it tends to make me believe it isn't a problem specific to this computer or even this small office network. There are no USB devices other than the mouse and keyboard and we've switched those out. We'd recently installed virus protection software, but we removed that and the problem still continues.
The only other thing I can think of, is that we recently installed a printer driver so the system could print to a Brothers laser printer attached via USB to a computer across the local network. And come to think of it, my system wouldn't even see that printer and allow driver installation until we plugged the printer directly into my system. After installation we moved the printer back, and changed the settings for the system to find the printer across the network. I'll look into uninstalling that driver next time I'm in the office.
Update: New day, new slow boot. This time I forced an early reboot and I got the option to start a Windows Startup Repair. I started that, skipped doing a System Restore and let it run. Finally it came back with all tests fine except the following which crashed: System Files Integrity Check and Repair , Failed , Error Code #0x490 , Time Taken = 541573 ms. So it looks like the test that checks for problems crashed, leaving me to wonder if there might still be some hidden problem. And yet reboots run perfectly normal.
This is on a loptop Meldon E6882, running windows 7, to a LED TV HD. From a cold boot both the laptop monitor and HDMI screen show the windows starting screen .. But the HDMI screen goes blank when the login screen appears. I have tried different screen resolutions. No Luck. I have tried from the 'screen resolution' page to get automatically detect the HDMI - No luck I have tried from the 'screen resolution' page to manually select HDMI. Only offers VGA or component, no HDMI.
I think this maybe a disabled driver as I did a manual disabling of these some time ago in order to try and reduce the boot time. I cannot recall the names of the drivers I have put into manual start (some time ago), nor have I found any info on what drivers are needed for the HDMI. The screen driver is an Intel(R) HD Graphics 3000. I'd like to look at some video on the larger screen...
We are just rolling Windows 7 out as we update machines. so far we have a dozen or so HP's (not my choice)with Windows 7. We are using Win2003 server as our File and Print.The printer causing issues is a RICOH Aficio MP using the latest C5000 PCL 5c driver.Our issue is on every cold boot on *most* machines first print of the day we get Error Message: "Do you trust this printer? Windows needs to download and install a software driver from the\servername computer to print to PRINTERNAME. Proceed only if you trust he\servername computer and the network, and then restart the print job."You add the driver, everytime, but makes no difference. Everything works fine for the day, if you hibernate the laptops and bring back to life, its fine.. but its only on a cold boot.Anyone got clues, it seems to be very common when googling,
I have installed windows 7 on my computer about a year ago. I've never had any problems to the point where I would need to reinstall the OS, however, I've noticed that on cold boots the system runs painfully slow, it will boot up fairly fast on a normal restart tho, like 20-35 seconds. On a cold boot it can take about 1-2 minutes to load in windows, and then once that happens its not so much it going slow as that there is a point during which I cannot click anything or else it will take forever to accomplish.
What I mean by this is, it will load to my desktop and for a period of about 3 more minutes I will try to right click on the desktop and it will do the circle thing for like 20 seconds before giving me the drop down menu. If I right click again right after, it shows up instantly. Same with trying to open up a file within those first couple of minutes. It will take like 45 seconds to open a picture. I have tweaked my windows 7 to startup only necessary drivers and turned off search index along with Aero.
My HDD isn't fragmented and I've got about 120gbs out of 450 available. So its not that bad. Now some of you may say, well its just loading the processes. But I only have catalyst control center loading up as a startup item. And even after it loads. It goes through a wierd 3-4 minute phase in which everything is slow as hell. Then works perfectly fine.
My computer is currently stuck on a black screen with a blinking cursor in the top left hand corner. I tried rebooting from a bootable disk and from a bootable flash drive and neither one worked. My machine is an HP Pavilion Elite HPE-110f. I am running on the 64 bit version. Has anyone run into this problem before and if so, is there a solution I can try on my own or am I doomed to take it to a tech?
I have a dell xps laptop that crashed and when I restarted it went into a never ending startup repair loop.I tried using the recovery function to no luck and now I have created a bootable windows dvd.The problem is when I try to boot from it, either the bios or hitting F12 to select dvd it just goes into the same repair loop - sometimes its the graphical ui and other times it's the black and white text telling me to repair or restore.I searched this forum and it seems that most answers want you to use a usb. Unfortunately, I do not have one large enough to put the Windows 7 iso on it
I have a year old Toshiba laptop that just stopped booting up this week. Worked fine Sunday, then Monday it would not start. Black screen with the option to repair or start normally. Repair goes through the motions and then states it was unsuccessful. Starting normally will eventually reach the desktop, but nothing will function at that point. The pointer is in perpetual hourglass when held over the task bar. Nothing, such as Explorer, will start.I pulled the hard drive out and connected it to another Win 7 computer via SATA/USB cable set. Initially, I could see the drive and access the files. Foolishly, I chose to run an antivirus before backing up the files. I was concerned about backing up the potential problem. MalwareBytes did not identify any malicious files, but Semantic threw up a warning about Yontoon-S.exe, so I attempted to delete it via Explorer. That action locked up Explorer. I rebooted the host computer. I should have backed up first because now I am unable to see the files. Explorer will assign the drive a letter, but when I select the drive to do anything, Explorer thinks about it for some time and then puts up a message that the drive must be formatted before it can be used. I do not want to reformat until I recover my data first. I tried to use SeaTools to diagnose drive problems. Drive fails the short generic test. I am not able to run Check Disk because Explorer thinks the drive must be formatted first. How can I get to the data before reformatting?
OS: Win 7 Pro 64 bit MSDNAA product key, all critical updates of course Comp: MSI-171 GX710
Every so often, as in every other boot or every three startups, or as today would have it every single time I boot up until I get fed up enough to come here, my CPU frequency is peaked out at an invariable 100% and my RAM usage steadily climbs from where it starts around 900MB-1GB until it too is maxed, and that is where my system crashes (to better define crash, black screen for a few seconds, and then it powers off instantly). I have attached a screenshot for reference.I have analyzed my resource monitor to watch this unfold many-a-time, and the process that is eating RAM is non-other than svchost. My CPU is getting killed by dwm. I can end and restart the latter but srvhost or svchost or whatever it is, is a system process. Not that the first one proved effective, but dammit ill get this machine to do what its told one way or another.T
When I boot my Win 7 machine and logon the desktop loads just fine, but when I click on the start button it freezes and doesn't come back - I can't click on anything. I think I've managed to narrow it down to being a problem with the DHCP service by disabling all services in msconfig and reenabling each one in turn. Everything was fine until I enabled the DHCP service - even starting manually after it has booted caused the issue to come back.
TSB SysInfo dump...
Tech Support Guy System Info Utility version 1.0.0.2 OS Version: Microsoft Windows 7 Home Premium, Service Pack 1, 32 bit Processor: Intel(R) Core(TM) i3 CPU 540 @ 3.07GHz, x64 Family 6 Model 37 Stepping 2 Processor Count: 4 RAM: 3063 Mb Graphics Card: ATI Radeon HD 5700 Series, 1024 Mb Hard Drives: C: Total - 231466 MB, Free - 189867 MB; Motherboard: Packard Bell, imedia S3810 Antivirus: None
A while back my computer crashed when playing ARMA2. I was playing and suddenly my screen turned black but the sound kept playing. I did a hard reboot and i got a Disk Boot failure. I decide to do another hard reboot and the computer turned on normally. After this i haven't had any problems any more.
Until yesterday when i installed a new game (Dishonored) A minute into the game the same thing happened as with the ARMA2 crash. Screen turns black but sound keep playing so i did a hard reboot. I got a Disk Boot failure but after a hard reboot it is gone again. But unlike with the ARMA2 crashes this happens every time i try to play dishonoured. I reinstalled the game on a different partition of the same drive and it stilled happened although this time it let me play for about 5min. But i don't think it had anything to do with reinstalling it on different partition it seems to randomly crash within 1-5 min.
I check a few other games and they don't seem to give any problems. I also did a chkdisk of the drive the game is installed on but no problems where found. I also did a memtest86 but also no errors.
My Windows is installed on a SSD but the game itself is installed on a HDD. don't know if that matters but i thought i just add that.
When I press the power up button my computer will start to boot to a blank screen. My main drive is a 120gb SSD and Slave is a 1tb hdd and will not start spinning. After about 30 seconds I can hard restart the computer and press the power button again and the computer will fully boot with no indications of a crash. If I press the reset button itself it will not reset the computer unless it is fully started. Also if I put the computer into sleep mode it will do the same thing. How to get my computer to boot the first time I start up the computer.
I have windows 7 installed on a PC I built a little over a year ago. I recently upgraded to the windows 8 consumer preview, but I didn't like it so I'm trying to switch back. When I install windows it works fine, I can turn my computer off and on as many times as I want and it will be fine, but if I install any video card drivers or any of the updates that windows tells me to install, the next time it boots up I either get the windows splash screen or a black screen right after it says, "welcome to windows", or whatever it says. I have tried installing only my video card driver, I have tried installing only one of the recommended updates, but no matter what I install it doesn't work the next time it boots, so this isn't a problem with one specific driver.The only thing I have changed since I had windows 7 installed before is that I got a new SSD, but I'm still using my old drive as well. I have tried installing on the SSD while the other drive is unplugged and I have tried to install windows on my original HD while my solid state drive is unplugged. I have tried installing on both, nothing works. I have formatted both several times. I have also tried installing both 32 and 64 bit versions, both to the same effect.
All I did was open a video strored locally with no connection to the internet. Shut down computer properly. I go to start it up and start up repair kick in. I have let the thing run on startup repair over night and a total of 12 straight hours. It reboots once, maybe even twice. Then it just sit a says attempting repairs. I just did a hard shut done. I was able to pull the data off using Uburba (not sure of the spelling). The USB 2.0 is not recognized in start up repair command prompt. I had a image saved to a CD. I can't get past the username password. The one I had wrote down does not work. System restore fails because I can't it doesn't have a .DDL file or it says something. If I could get the USB 2.0 to work I have an external that has a couple of images that would be better than re-installing. I tried moving the image into the computer then using the image restore, but I learned that doesn't work because it somehow tracks were it wrote the image to. This is way I need the usb 2.0 to pull the image from my external HD.What is the default password of HomeGroupUser$?
I have built my computer about 2 months ago now, and had nothing but issues with it, display drivers stopped responding, alot of BSOD (bccode 1a and 50), black screens, lockups and so forth, i have FINALLY read enough forums over this 2 month period to solve majority of problems accept one, Computer runs fine, but every morning on cold bootup it'll start to load POST and then go to a black screen and just stay there unless i reboot the computer and then it'll bootup fine. I will turn off the computer after that and go to work for about 8-10hours come home and turn it on all fine, untill the next day. I have tried new ram, fail safe settings in bios, updated bios to the lastest, bought a new power supply, tried reconnecting everything, unpluged storage harddrive. Only thing i could think of causing the problem is my video card drivers, because as soon as i install the drivers i get "drivers have stopped responding but have recovered" screen would lock up freeze/artifacts and then come back, until i changed my idle clocked from 157/300 to 400/900 and it sorted out that problem, but those settings dont kick in until i reach into desktop, could it be trying to load the ati drivers during post and black screening?
I was uninstalling AVG and my syatem would get the BSOD and xrash before I completed it.Eventuallt my whole system crashed and all I get is a message on a black screen fron Phoenix Technologies aaying 'Boot from BBS-harddisk'.Anyone know what this means and if this screen can be bypassed. I can't use f2, f8 or f12.
I have an ASUS n80vn laptop that is about 3 years old. It came with OEM Windows Vista, but I installed my own copy of Windows 7 Professional 64bit more than two years ago, and there was no problem upon installation.
Lately (for about a month), I have been receiving BSOD either during boot or the log-in screen. The BSOD usually happens only once per day, and I would be forced to restart my computer. No BSOD upon restart. I suspect the problem occurs when the laptop is cold. I have attached the BSOD Dump files collected over the past month.
The only driver change I've had was nVidia graphic driver updates. I've uninstalled and reinstalled the two most recent drivers and the BSOD problem still occurs.
On a side note, I have been getting random freeze-ups too, and this has been happening before the BSOD problem. These freezes occur when I'm doing regular tasks such as web browsing or typing in Word/Excel etc. When my system freezes, there is no BSOD, but nothing can be moved (keyboard + mouse won't do anything). Closing lid does nothing too. Strangely, I have not been getting this kind of freezes when I play games.
Quick rundown of specs: -Windows 7 Professional 64bit (retail) -Age of hardware: ~3 years -Age of OS: ~2 -Processor: Intel core duo P8600 2.40 GHz -RAM: 4GB -GPU: GeForce 9650m GT
I have BSOD on a cold startup everyday. On most time after the first BSOD of the day the PC will run fine for that whole day. There will be two consecutive BSOD on certain occasions. The problem stops for a week after I updated the NEC USB 3.0 Host controller so it seems there is other problem causing the BSOD but now I am not so sure.
This is not a typical BSOD crash. My Dell Inspiron's monitor intermittently doesn't wake up once power management shuts it off. The problem is monitor doesn't fully shut off. One way to know the monitor won't wake up is when the CPU is griding away, fan is on full blast, laptop heated up, monitor still has a faint white brightness but no disk activity. I have tried connecting the laptop HDMI and VGA output different monitors and TVs but the monitor/ TV doesn't recognize any input signal during this phase. Yesterday, CPU suddenly started griding away without a pause while I was working and the base plastic was so hot I couldn't place it on my lap anymore. System Idle was 95-99%; I wanted to check whether laptop will not wakeup after power management kicks and this morning I couldn't wake up the laptop and had to cold boot it
I cannot put my laptop to sleep or hibernate when this occurs, the computer will just keep griding away with fan at full blast but will never hibernate or sleep.
I've run chkdsk, defrag etc but no issues were reported. I have checked for viruses etc, nothing obvious.
I have a brand new Windows 7 64bit build with a clean install from an Upgrade CD and noticed in BIOS that my 1st boot device must be "Windows Boot Manager" or it asks for the CD. I only have 1 storage device (SSD) in the system and when I look under Disk Management in windows, it shows a 100MB "EFI System Partition" in addition to the primary partition (which is labeled "Boot, Crash Dump, and Primary Partition" - so it seems to have the boot files on it).
As I only have the one non-optical storage device I did not set any partition parameters at install. I Attempted to do a Startup Repair with the windows disc to maybe try and delete the EFI partition and got the "... System Recovery Options is incompatible with the version you are trying to repair" error. Not sure what that is. If Disk Management shows a healthy partition with "Boot" listed as being contained, why can I not select the SSD as boot device #1? I can boot perfectly fine with the Windows Boot Manager listed as boot device #1 and the SSD as #2, however it's not ideal.
I read through a few threads with similar topics but the issues were either not quite the same and/or resolved comparatively easily. I am trying to repair a 1.5 year-old HP Pavilion running Windows 7 Home Premium 64. This machine is used as the main office computer in a small doctor's office. In spite of my warnings, anti-virus software was not installed until it was too lateThere was a major issue about seven months ago that required another company to repairThe problem is explorer.exe will not run. Double-clicking a shortcut on the desktop, clicking the text name of a program from the Start menu, and even in the cmd results in the same response, a dialog box pops up stating windows explorer has stopped working.
windows is checking for a solution to the problem. followed by another box stating windows explorer is restarting. But the requested application never starts. I have run the Ultimate Boot CD 4 Win, replaced the hard drive and cloned all data, run numerous registry scans, malware scans and antivirus scans. Initially removing over 1500 virus/malware hits and over 1400 registry errors. But the main problem persists, explorer.exe won't open programs.
I have BSOD problem only when computer is "cold". example: After night when computer was turned off.
After a few restarts the computer starts normally and I can reboot, turn of and on with no problem until is "warm". When switching off for a few hours BSOD comes back.
I've had a notebook (asus N51V with a T9550 and 4 GB of RAM with Windows 7 Ultimate) for over three years and I've not had any significant problem until a couple of days ago. Now, after it has completelly booted and I've opened some applications (for example Eclipse, Windows updates or even no applications) it appears the BSOD with the page_fault_in_nonpaged_area STOP: 0x00000050 and other information. I've managed to get the minidump and to do a "photo" of the BSOD with my cell. I'm attaching the minidump, but if someone need it I can put also the photo.I've not added any new hardware for over a year and I've not installed any significant and heavy software in the last couple of months, so I do not know what can it be. To be sure I've also done the memtest86 an it did not found any error.
i`ve just purchased a hp deskjet 3055a wirelesss printer.its set up to a home network with 3 pc`s using it 1 is xp home, 2 is win 7 hp 32bit and my main machine is win 7 hp 64bit.the last machine is giving me a problem it does not always turn on the print spooler service if i try turning it on in admin services it will not, only by restarting will it work the other machines on the network work fine.
whenever I try using IE9 to download something (so far just a 634mb mod for arma 2) it crashes after you do the "click here to download" , it correcly goes to filefront but then crashes before anything else happens.
my windows oftenly crash everytime i refreshes the desktop for more than 3 times or open a larger memory folder.(eg. documents or the C:drive) this is the details of the crashes.