I have a Toshiba laptop with 2 partitions- One with windows vista on it and one for backups. I want to join the two partitions and use the Windows 7 Upgrade pack and do a clean installation. How would i go about joining the two partitions? Am i able to use the upgrade version to install it?
View 9 RepliesI know I have did this when I was installing Win 7 and was able to have Win 7 do the partitioning. If possible can some one tell me the screen where i can get into the partitioning phase. I can't find it again to save my life.
View 2 Replies View RelatedThere was a time when I had Windows 7 and absolutely adored it.
For certain reasons I tried to go back but fail epically (yes, I'm a teenager!) and now I have two active drive partitions and it's still looking for Windows Seven's bootmgr.w/eand now I need either one of four questions answers so I can get back on my new computer. [(BTW, I am starting to hate the way I need to tweak things.)]
The questions are:If I install windows seven on my usb flash drive (which I tweaked to make the computer look at it like a USBHDD,) will it wipe out the OS on my grandpa's computer? How can I make BIOS look-up and process boot.ini instead? How can I run the Windows Vista install off my FlashHD [as I call it. :P]Is it even possible? Would it work better or, once again, is it possible to install Vista on my flash drive and use it to run on my grandpa's computer. My computer is an Acer AspireOne [I will deservingly accept flaming due to my poorness and poor sense of choice].
I used to have an external hard drive enclosure, and I stored large video files onto its 1 TB capacity. I built a new machine, sold the enclosure and used the same 1 TB hard drive with the UNbacked up files still therein. Obviously I am new to this otherwise I would not have done this. I realized my mistake when I went to install Windows 7 and it said to back up your files.
I read further and discovered the reason was "They will be deleted". I really don't want to loose these files. Is there any way to install the OS without deleting the files. Can I install another OS like Linux, then partition the hard drive, delete linux then install windows 7 onto a partition? WHAT ARE MY OPTIONS! OTHER THAN BUYING ANOTHER HDD ENCLOSURE!
I recently bought two ssds and striped them with my on board raid. Any ways i got windows 7 installed on it just fine ( after i got the driver issues worked out)But my problem is that I was looking forward to a fast boot time, but now every time i boot it go's to a screen that detects all of my storage devices.
View 7 Replies View RelatedI have windows 7 32bit and going to clean install the 64 bit version and the OS is on drive C (or partion C) so I copied my personal files to drive G,If i clean install windows 7 64 bit will it delete everything on my hard drive or will it just format the partion that has the os.
View 1 Replies View Relatedi tried many time to reformat, then re-install win 7, pc re-started and stopped at the black screen with mouse cursor, i have tried F8 and start up repair, nothing helps.
View 1 Replies View Relatedi had clean installation of windows 7 professional sp1 32, on VAIO VGN-FZ11Z.it is giving me many validation errors here n then, mostly when i launch an application or setup file. I have not installed any drivers for it until now bcz im not finding them. The windows is also flagging for driver of firmware parser driver but im not finding it anywhere on support of Vaio website. Some error messages and snapshot of device manager attached below. Kindly help me out . also tell me which drivers i must install for sony vaio vgn-fz11z for Windows 7.
View 5 Replies View Relatedi am going to install a factory oem windows 7 on my hp laptop following the gregrocker tutorial. now when i check the hp support site for drivers and softwares, i am confused on what to install and what to not.
1. Driver - Audio High-Definition (HD) Audio Driver
2. Driver - Chipset Intel Chipset Installation Utility and Driver.Intel Management Engine Interface (MEI) Driver.Intel USB 3.0 Host Controller Driver
3. Driver - Graphics NVIDIA High-Definition (HD) Graphics Driver Intel High-Definition (HD) Graphics Driver
4. Driver - Keyboard, Mouse and Input Devices Validity Fingerprint Sensor Driver
I've done a clean installation of win 7 home for a mate on his laptop and want to use the product key that is underneath the laptop to complete the installation but the key has faded completely, I've emailed toshiba about it as its a toshiba model but ive had no response and its been 2 days. Is there any way to retrave it any quicker?
View 9 Replies View RelatedAfter formatting and setting a new partition using the installation disk, I install Windows 7, all goes well. But as soon as the installation is finished and my laptop restarts, it wont boot from the HDD. I keep getting error messages saying:
Windows Boot Manager
Windows failed to start....
File: ootBCD
Status: 0xc000000e
[Code].....
A copy of the current boot configuration data will be saved as c:ootcd.backup.0001
However when i hit the "ok go ahead and fix it then!"-button i get another error saying Startup Repair cant save the new boot options. Anyone know if i can fix this problem with BCDedit or bootrec.exe
Got Windows 7 Clean Installation over the computer's USB 3.0 port done without too many problems but with some hassle anyhow.For the clean installation I followed the procedure of GreGrocker Clean Reinstall - Factory OEM Windows 7 and put the whole installation onto a 4GB USB Flash Drive.From the computer's USB 2.0 ports there was no problem whatsoever and Windows 7 got installed very quickly.However, over the computer's USB 3.0 port things weren't easy. I finally got it done by uploading the proper USB 3.0 Root Hub and Controller drivers *.ini and *.sys files.Strangely enough, at first everything went well over the USB3 port and the WinPE environment with its RAM drive (X:) got deployed correctly. The only sensible explanation for that is that the computer's BIOS used the appropriate and build-in USB3 driver to do that part of the job.However, once the the installer (located in the X: drive) was about to install Window 7 on the system HDD, it asked me for a CD/DVD driver. I loaded the appropriate USB3 drivers at that stage and the installation process continued over the USB3 port.I had a closer look in the RAM drive (X:WindowsSystem32DriverStoreFileRepository), and indeed, there are no USB3 drivers present anywere in that folder, only USB2 drivers where in there, named: usb.inf_amd64... and usbpor.inf_amd64... So I was wondering, as USB3.0 is so common and the future standard, why aren't there any USB3 drivers in that folder present? Is there any possibility that the creators of the Windows 7 Clean Installation files (Digital River, or My Digital Live) could put USB3 drivers in the Win7CI package?
View 1 Replies View RelatedPurchased a Windows 7 64 bit Professional (academic). I have been originally using a Windows 7. However, the HDD had been giving me fits and has currently died. I'm not unable to activate my upgrade key since my new HDD does not have an old version of Windows to upgrade from. What should I do?
View 1 Replies View Relatedyo guys i am going to install a factory oem windows 7 on my hp laptop following the gregrocker tutorial. now when i check the hp support site for drivers and softwares, i am confused on what to install and what to not. [code]
View 2 Replies View RelatedI'm using Window7 RC 7100 , after clean installation and while connection my game controller i went to control panel but i couldn't find Game Controller Setting ? is it hidden if so how to make it visible and if not how can i get it.
View 9 Replies View Relatedi was just wondering how i extract the files from an installation disc onto a flash drive, so i can use the flash drive to perform a clean install.Extract Files from Windows 7 Installation DVD.i already looked at this but it wasn't specific to my uses.
View 3 Replies View Relatedi was wondering if anyone has any programs they could recommend to use to wipe a hard drive clean before reinstalling windows 7, I noticed you have this CCleaner 3 link on here CCleaner - Download.com If i put that on a disk and started it up as i would to reinstall can that wipe the disk clean?
View 9 Replies View RelatedSo i'm trying to do a clean install of windows 7 (x36) from XP that im currently running. i've burnt the iso down on a dvd and it boots fine and the installation runs normally. I'm getting through all the steps within the installation when it at last says something about that it's done and it's going to restart for the first use of windows 7. Now i'm getting my problem.
The computer starts up and goes through the memory testing and such but just as it's about to start windows 7 i'm getting a black screen and my monitor says "No signal - blabla" and 3 seconds later it restarts itself. If i don't do anything now my computer loops this restarting on and on...
So i've tried to install it with removing my two 512mb RAMS and only have two 1gb of the same brand. Didn't help.
i had windows vista on my pc and i did a Clean Installation of windows 7.but now i have some problems,and i want to install windows 7 again.do i have to go back to windows vista? i have a windows 7 upgrade dvd.
View 9 Replies View RelatedI have a Samsung series 9 (NP9004XC) and I am upgrading the 128gb SSD that came with the computer to a Crucial M4 256GB mSATA. I am doing a clean install from a bootable USB that I created from the recovery disc that was included with the computer.I can load up setup but once I get to the part where I choose what disk I want to install it to I get an error. There is only one disk listed (Disk 0, Partition 1) and when I try to select that disk to install Windows to I get the error:"Windows cannot be installed to this disk. This computer's hardware may not support booting to this disk. Ensure that the disk's controller is enabled in the computer's BIOS menu."
View 7 Replies View RelatedI've been troubleshooting this computer for some time now. At first, I disabled RAID because of the blue screens and I found that one was bad and the second of the RAID 1 appeared fine. Well, I installed XP to ensure it would work and that was extremely slow. My client didn't have a disc to XP MCE, but instead bought Windows 7. The installation took about 12 hours and the system is often unresponsive. On resource monitor, the 2.13Ghz Conroe CPU is barely tapped and the 2GB of RAM is barely at 30%. However, the system takes forever to boot and it very often stops responding for a period of time.
I did my research and found out that this model--original specs--can handle 7 better than this. I told the client it was probably an HDD error, as it seems to hang everytime the system must access the HDD. I can't even run the Index to find out what the systems rating is. I mem tested the RAM and chkdsk the HDDs before removing the first because of its clear faults in its inability to hold an OS installation. I recently installed the 2.5.3 BIOS update, but I haven't had a chance to install a newer version of Intel Matrix Manager.
so for about 5 days, i have experienced random and sporadic bsod, before that it was normal and stable. i did my installation on my os on october 2011. i'm quite sure it's graphic driver but i've clean installed almost 10 times and still crashing. it crashes randomly when i opened a Internet video or open a video file, everything regarding to video. i'm already feeling hopeless here
my specs are
win 7 64 bit home premium (not oem)
gigabyte x58 ud3r
i7 920
gigabyte gtx 480
asus xonar essence stx
3x2 ocz ram 1033 mhz
my os is located on my ssd which is an intel 510 120 gb
i got 1 tb hard drive caviar green
i got 500 gb hard drive caviar green
and 250 gb seagate (really old, it's ide iirc)
i've uploaded the minidump and system performance, i hope i did right on the attachment (first time posting here).
i clean installed new WINDOWS 7 PROFESSIONAL 32bit on laptop SONY VAIO VGN-FZ11Z.Operating system is genuine but downloaded from MSDN. But it is giving me a lot of process validation errors. Genrally these errors are coming on application launch. After that mostly application aborts or restarts.
View 2 Replies View Relatedi have built my computer with new parts and the installation stalls returning the errror code: 0x80070570
View 1 Replies View RelatedMy daughters CQ61 required a clean install after repair. Windows 7 jus goes through the normal install process and hangs at completeing installation. I'm not a Noob but not a Geek either. I can only assume the drive is fine as it is running fine in the T400 IMB i am using now. Now here is the strange bit..... When i was just starting out i to had a CQ61 and it too needed a clean install and it did the same for months with friends in th know looking and trying to. In the end i send off for the factory software discs and tey went on straight away with win7 working fine. It was literally restored to new. I passed on said disks when i sold said CQ61 adising the guy never to go down the road i had. Now the software discs are no longer available from HP and There is none on torrents anywhere. I cannot accept that this is the only way to install clean install. If it was that critical to have the discs they would send them out with the new machine. So thats muti attempts by multiple people on 2 identical machines presenting the same hang. One was solved with the Sowfwaredisks provided by HP and are no longer available. Should have copied them i know but never thought i would be looking down the same barrel of the same gun.
View 1 Replies View RelatedI am getting an error "cannot install" 0x80070714 when I try to install windows 7 into a clean disk and the installation just stops..
View 3 Replies View RelatedI am new to windows 7. Recently i bought a laptop with windows pre-installed in it.
I have a HD drive of 500gb. Windows is already preinstalled on it. I Want to partition the drive without affecting any data. I loaded some 30 gb data already on the drive. I want to partition the 450gb drive into 3/4 drives each of 100gb, such that i can allocate the Os with a drive and remaining 2/3 with my personal data songs, movies...etc.
I want to partition the drive and I don't know how??? Can anyone please explain me step by step how to do it. The main point here is do i need to again reformat the whole drive such that before re-installing Windows 7 i can partition it (or) do i have any alternate solution such that while running windows I can partition the current drive without affecting any data other than system files.
I have a 2 partition disk split: C:Windows 7 & E:data . I want to sneak in a partition at the start of E: to hold XP os and thus "F:" becomes my new data partition. Shrink as far as I know will create a space after the currently existing E:. The added problem is I am only playing with a small drive and cannot just copy over the data.
View 6 Replies View RelatedOne day I booted up my comp & My HDD was Partitioned into 2 Parts. My C: Drive Also my Boot Drive has Windows 7 on it while The other Half of my HDD My F: Drive has all my files on itI was wondering how I could Merge these to Together without hurting or losing anything on my comp?
View 9 Replies View RelatedI currently have a dual boot system of XP and 7. Xp was the first installed os. After partitioning Windows 7 was added and made the default os.
I now want to get rid of XP and reallocate the space to Win 7. I have assumed that I can do this from within Win 7 using Disk Management. From win 7 the partition for win 7 appears as C: and for Xp its D: And likewise from XP the partition for XP is C: and 7 is D: (if you follow what I mean).
Now when I try to delete the XP partition from Disk Management it does not give me the option to do so (the option is greyed out). Is there a way around this? If not I may as well just wait until I get the retail copy of 7. I am going to presume that the mbr is most likely to be on the XP C: drive? as that was the os installed initially.
After all the trouble that I went to remove the old partitions on the HD in my secondary rig, I forgot to disconnect a second HD installed, and after going through a number of other repairs just before starting the installation, I wasn't thinking clearly and deleted the partitions that I had made with the HD installed on my primary rig.
Attempting to recreat the partitions with the installation procedure got things even more messed up because I didn't find any facility for actuallyt creating a partition of the size that I wanted, only a format function, which I assumed would format the entire drive, or as I did, click Next, hoping to find something more in the next screen, but it then just started the installation itself, and took the entire drive, except a 100MB partition that it also created for the system reserved functions.
Not being in the mood to once again remove the harddrive back to my primary rig for prep, I let it continue the installation, because it would not permit me to delete the partitions that it had made. I'm hoping that I can resize the main partition after the install completes, but if like when I installed the x32 bit version in this manner, it scattered files across the partition in a fashion that would make it difficult to do so.
On my primary rig, I have the entire OS installed on one neat 100GB partition, and that is what I want here also. I'm trying to decide whether to nuke the HD again, or finish the installation and attempt to customize it afterward. Which would be better?