Whenever I do an ipconfig I get a bunch of connections that are not active. It lists my active connections, but then I get a whole series of these: Tunnel adapter Local Area Connection* 6:
Media State ....... . : Media disconnected Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 7:
Media State . . . .. : Media disconnected Connection-specific DNS Suffix . :
Connection-specific DNS Suffix . :
They don't seem to be causing any harm and the only downside is that I sometimes have to scroll around to find the connection that is active. What are these?
I started to have problems with Local Area Connection in Vista, during logon there was two networks identified, one that I had set up and one unrecognized. This was a problem, because it disrupted the DHCP discovery. I have read here that many have the same problem, but so far haven't been able to pinpoint the cause. My solution was to try to disable the network connection and enable it. This seemed to work sometimes, but once I rebooted the machine, the whole network adapter had disappeared from device manager. I tried re-installing the driver but Vista doesn't seem to recognize it. How do I get Vista to install it back?
I'm using Vista on a HP Pavilion laptop and i'm having some problems with my internet connection. I know very little about computers and so struggle to follow much of the advice on these forums! I'm trying to connect using an ethernet connection so it's not a problem with the wireless. The network and sharing centre shows that i'm connected to an unidentified local network but it isn't connecting through to the internet.
I am the manager of my network at my house and i have set up my router with an encryption key i can remember. My mom just got a new laptop and we can not connect to it because i FORGOT THE KEY! My computer is wired directly to the router. I went to my IP address and wouldnt you know it, i forgot the login info! I can reset the router from the router itself, but it took me a while to set it up. Is there any way i can get around my login since i am directly connected?
I can't log into my computer by normal mode,safe mode and safe mode with network.This started when i log into my computer and start a game and attempt to connect to my BroadBand connection.While connecting, my Local Area Network is undentified so i restart my computer and i can't log in till now.
I have with Vista and an ad-hoc peer-to-peer wired network. When I run the wizard to connect to a network, it does not show the add ad-hoc network option, only four others for wireles, internet and vpn connection. Also, although I have networked two PC's both running Vista, I cannot ping the second machine from the first and vice versa despite having added routes to both machines. nslookup recognises the ip address of each machine, as does tracert(I should point out that both machines obtain their iP addresses from a router which also allows access to the internet. Both machines can see the internet).
I have a Dell Inspiron 1720 with Windows Vista I'm trying to connect to some unsecure wireless networks at a friend's house for the first time and am only able to connect with local access. I try diagnose and repair and it says that there are no issues. Three other computers are connecting to the internet just fine. They signal is good, and there is supposedly data being sent and received but no programs will connect to the internet. This issue has never happened before. I regularly run a registry cleaner and tried restoring to a backup from a couple days ago and that didn't help.
Recently built out of spare parts and some new parts a Media Center PC. Loaded Vista Ultimate X64 on the box and have it hard wired to my network. Issue is limited connection on my network and no internet connection. All was working great until SP1 was installed. Since then I can not access the internet, ping my router or see my WHS or my wifes XP Pro laptop, but I can see and access my daughters laptop running Vista Home Premium and my laptop running Windows 7 RC1.
I have tired to disable IPv6 both through the proprieties on my nick and through the registry, no effect. Tried netsh winsock reset, no effect, also when I go into network settings network discovery is turned off, I enable it with no effect, next reboot it is off again. I saw a post about putting local services group in the administrators group, no effect. I have a D-Link DI524 router my MC PC is showing up in the assigned IP tables, the IP that is returned when I do an ipconfig matches the one issued by the router. As I stated before I had NO network connection issues until SP1 was installed. Is my only option to un-install or remove SP1, is that even possible?
I have Vista home basic 32bit And I am connected to DSL via ethernet (wired). About a week ago I stared having a issue that my browsers would stop working(both firefox and internet explorer)I would get the typical error saying the connection has been reset.My modem was showing that I am connected tho.
At the same time my AIM messenger was working fine I was still connected and able to send and receive messages.I tried to reset my modem that didn't work.So I restarted my pc and that seemed to fix it. This has continued to happen daily now usually around the same timeframe too.
I have scanned my pc with avast,super anti spyware and malwarebytes and they haven't found anything wrong.I tried disabling my firewal (pc tools firewalls plus) that didn't work.I read that zonealarm could cause this issue and i had it in the past but it's been long uninstalled. The last thing i tried was i disabled avast web scanner and i reset the TCP/IP Winsock. And again it didn't work.
I recently bought a new Linksys router ultra range plus. it can broadcast on n, g and b bands. My laptop has a "g" adapter. but after setting up the router i tried to connect to the router and only get "Local" connection. DHCP is enabled in my router but the "ipconfig /all" command on the laptop says it isnt. My room mates connect fine, one has a Mac and one has an HP running vista (not sure the version). When i connect via ethernet the internet works just fine. im leaning towards an adapter problem but im no pro in this field. iv updated the adapter drivers to the latest update (attempting to solve the problem).
I've searched everywhere looking for the fix to the "Local Only" network problem. I've had it a couple days and can't find why I can't get through to the internet. I have disabled IPv6 and tried static ip which I don't think works with my router and some registry fixes and cmd commands. I'm connected through Ethernet wire so it's not a wireless thing. I don't know if I should switch back to XP Pro or maybe buy a new network card. .....The first is if I set my ip static and the second without it. It seems that if I don't set my ip static then it does not find the router and only finds unidentified network while if I set my ip static it does but I don't believe my router works with setting static ip from the computer. I can also see the other computers linked into my router but just can't access the internet making me believe it is something with the compatibility with the router and Vista. Okay here it is, this is all without IPv6. STATIC IP: C:UsersChris>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : Chris-PC Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No.............
I installed sp1 last night and this morning my internet was gone, the network controller on my machine couldn't find any connections, though the control panel insists the device and the driver are working correctly. I just uninstalled sp1 and got back my connection. I'd done the install hoping it would fix a problem that just started happening: Vista no longer recognizes software CD. Up until a few weeks ago, if I inserted a CD containing software (e.g. adobe CS2), the autoplay brought up the start menu. It not only no longer brings up the start menu, but when I click on the cd/dvd drive in explorer, it asks me how I want to format it. Nero's info tool reads and determines that the disc contains the software I want to install, but vista can't get to it. The only plus side of sp1 was that it correctly reports how much RAM I have installed, instead of 2.93 as it did prior to sp1. Any idea how to install software now that Vista no longer recognizes software media?
i used advanced vista optimiser to give my laptop a good clean out as i do every week. but this time when i went to log on the diagnostic comes and says either change proxy settings or try resetting local connection setting. i tried resetting many a time which as done no good. web address bar states where its going but the diag box comes on again.so in the mean time while this is all going on a new tab keeps on opening by its self and saying the same thing,this started to happen before i cleaned my l.p but it was just redirecting to a blank page.
that is why i did the clean.anyhow resetting the lan did not work so i reset the internet expolorer in the tools on the bar. which as worked but the same thing is still happening with the tab ,but now its redirecting to all the freebiee sites and it will not stop. i have spyware-adware-trojan software on my l.p and still no good it did pick up 3 infections which it sorted out, its driving me f*&^%*ng nuts:mad::mad:
I'm having a problem with Vista's networking. A lot of my friends who still have XP are able to use remote desktop and tunneling services easily, where as I am unable to on my Vista machine. It's quite ironic cause I'd think Vista (newer than XP) would have better networking capabilities. But that aside, I've followed the instructions in order to install Tunneling on Vista (Since MS removed it from Vista) by going to programs and features and adding the telnet feature. This seemed to work somewhat, but now I'm trying to use SSH Tunnel Client to connect to a server and I'm unable to. Overall it seems Vista is locked up tight. Is there any information I can get in order to open up Vista in order to do what I want to do. I've looked at a lot of Q&A's, tutorials and how tos, but most of them explain very basic things. What steps do i need to take in order to connect to a server using SSH in Vista?
I have a issue with my Linksys wireless USB adapter. I am trying to use it with Vista Home Premium. After installing software... I plug the adapter in (like directions say) and windows update goes to work. It updates the driver, installs correctly, I then connect to my home network and all is good. My prob is for some reason I lose internet and the USB adapter itself. One time I switched users and lost all. I have tried uninstalling adapter and tried reinstalling by pointing to my D drive (install CD) in hopes of using the driver that's on the installation CD. as soon as it saw everything.. windows update once again gave me the same buggy driver. I have tried to install with UAC disabled... no luck... the Linksys website/support for drivers has the same updated driver. I tried to use an older one but Windows keeps forcing this updated one down my throat.
I got a Nvidia 8400GS When i got the PC but brought a Sapphire ATI Radeon HD 3870 X2 / 1GB / PCI Express 2.0 / Graphics Card. My brother took out the Nvid card and then formated the PC to make sure that all drivers where uninstalled then put the ATI card in. In divice manager under dispaly adapters there is standard VGA Graphics Adapter and further down the page there is "Other Divices" with Video controller. When it installs these some times the standard VGA Graphics Adapter fail but the video controller succeed but with error. saying. "Incompatable display Adapter has been disabled. At least one display adapter on the system has been disabled because its not compatible with the driver for the VGA adapter". lso i carnt change the resolution above 1024X768. Also my Graphic card is a Sapphier brand but in the windows update its looking for ATI Technologies Inc. - Display - ASUS EAH3870X2 Series
From time to time, specially when I`m doing heavy uploads or heavy downloads my connection goes from full internet to "Local Only" or "Limited Connectivity". Thus, all internet access is lost until I reset the connection (disconnect and connect again). When the connection is reset, the problem is solved and the issue is fixed, that is, until it happens again a few hours or days later.
I`ve found out that this is quite an usual problem for all Vista users, most of my friends have this same problem and I`ve seen hundreads of posts in the internet about it, but no solutions were found. I`m running Windows Vista Home Premium 64bit on a HP dv7-1245dx notebook. I have another PC which also runs Vista 64bit, two notebooks and a PC that run WinXP.
From all of these machines, only the ones running Vista are affected, I do not have this problem with the machines running WinXP. All machines are wireless (connected through WIFI) but the PC running WinXP. I`ll use my main notebook as the scenario for troubleshooting. ...........
Task Scheduler (Local) Upon opening TS..a error box populates and no (Local) data. Upon Xing close the error box...data populates.. Message in error box..The Task Image is Corrupt or has been Tampered with.mcupdate...I ran sfc..nothing reported
The notification area, down by the time, has 13 icons showing. And there isn't any "<" or ">" symbol near them at all. Is there setting that I touched on accident that disabled the notification area's ability to collapse after a certain number of icons are displayed? Or, is it normal for it to show 13 icons without collapsing....
Not sure which newsgroup I should be using. Hope this is the right one. I have an avast icon in the Notification area. Each time it completed an virus data base update, it would pop up and make a verbal announcement. It is quite annoying, and sometimes disruptive. I tried to hide it by : right click task bar > Properties > Notification Area > Customize > select Hide on avast! ( both ). Won't work. Still shows up for an announcement.
Just recently a new icon appeared in the notification area and I can't get rid of it or even find out what it is. If you hover over the icon, there is no pop up message saying what it is. Left and right click don't do anything at all. I've looked in the customise icons section but it is just listed as "<no title>".
The icon looks like two figures in front of a small window, with the windows shield at the front. I've tried to attach a screen shot of it. It's the second one from the left.
It appears shortly after starting up the laptop and then won't go.
I've got an ACER Aspire 5735, running Vista Home Basic.
Is there a way to identify the items in the notification area?
I have an Asus Motherboard that has an EPU-6 Engine (EPU = Energy Processing Unit, all it does is maximize energy usage on the mobo). It comes with a small app that puts itself in the Notification Area so that you can change between energy profiles easily. I like the app, but I don't want it shown there all the time. I already tried the "Hide Inactive Icons" option, and also tried to hide it manually by selecting "Hide" from the drop down menu in the "Custom..." options. The problem is that it hides the icon, but when I reboot, all those settings are undone. Is there a way to fix that?
I am running Vista Home Premium. I have a Windows "New Update" icon sitting in my notification area which I do not want or need. Does anyone no of a way to get rid of this irritation
I have an existing wireless home network for file sharing and what not. It was no trick to get this working with XP. Vista was problematical, but is now working. How can I connect my Win7 to the home wireless network? I've been searching and experimenting for days, with no success. This is not a Home-group solution, since I have but one Win7 machine.
I brought a brand new Packard bell PC Ixtream M3720 and I keep getting BSOD when I game i last for like 20 min before the pc gives me bsod, The BSOD is page fault in non paged area 'Send big files the easy way. Files too large for email attachments? No problem! link to the dump also all packbard bell appilcation apart from recovery manager dont seem to work they say it stop working and it closes this goes for setup my pc and all of them
I was cleaning up my screen and keyboard with windex, foolishly, with the computer on, when somehow in the course of working on the keyboard I managed to flip the viewing area on the screen 90 degrees so that what was the short dimension (up-down) is now the long dimension (left/right). Some combination if key press' will put it back to normal I guess. But looking hard at the icons on the keys... its not at all clear which ones.
I have a program in my start menu that when I select it it doesn't open, it mealy places it's icon in the notification area of the task bar. This has forced me to right click and select 'Open' form the icon's context menu. I tried changing the 'Run' box to maximized but it didn't work. The original folder the program put in the start menu after installation worked ok. I have since removed it and added just the executable to the star menu which is what doesn't seem to want to cooperate.
I keep changing a Notification Area Icon to 'Show' but it keeps getting changed to 'Hide when inactive'. I do have the 'Hide inactive icons' checked. So what good does it do to be able to change the icon setting to 'Show' in 'Customize' if it keeps changing back? Any way to keep this icon showing without unchecking 'Hide inactive icons'???
