I am a new guide here, and have a private network setting question.I am using Vista X64 Business, and connecting to internet through HUB without IP sharing function. I set the local area connection to "Private" in "Network and Sharing Center". But it would change to "public" if I restarted the computer.
View 9 RepliesI have Vista x64 and I have read threads on this for weeks and can't fix it. I have file sharing/network discovery on, private network, password protection disabled, my shares set to everyone and everyone is on the same workgroup. My problem is that the x64 Vista computer will not see any of the XP (x86 or x64) computers and they can't see it from the Network Neighbourhood. However, if I type the IP address of the XP computers I
can access them. On the XP computers if I type the IP address I get an error that it isn't accessable and I might not have permission. However, if I type \192.168.0.100share or any of the other share names I access it just fine. pinging works too by IP but not by name. If I boot into the x86 install of have of Vista I can access XP computers from Vista and the Vista from XP by name and everything without typing any user names. The only differince between the two aside from x64 and x86 is that x86 isn't patched past SP1 as I don't use it often. Lastly after installing that XP patch I can see the x86 XP computers by name from the network map feature on Vista, still can't access them by name though...
Just returned from holiday and while we were away I changed my laptop network in vista from private to public as advised and the internet worked fine. Now at home I can’t connect to my router, and I get a message saying that the details held on the computer is not the same as the router. Also there is no “customise” function being shown on the network and sharing centre screen to switch back to private network. I’ve tried everything to set up a connection, even a new one, but the same message appears all the time.
View 7 Replies View RelatedI have two windows xp computers behind a linksys router. I would like to be able to access one of these computers from a vista computer while on the road. I am looking to purchase a linksys/cisco vpn router BEFSX41 and getting a static ip address. How do I go about this? Do I need specialized software in addition or can this be accomplished without a lot of hassle?
View 4 Replies View Relatedmy network connection keeps switching between public and private, despite my configuring it to a private network. Because of this, my PS3 is unable to connect (using laptop as media center to stream data to PS3). We are using a DLINK DIR-615 at the moment. I also have Linksys WRT54GS that I could switch back to, but I had problems with my laptop staying connected with that and we had the Dlink kicking around, so we swapped to see if my laptop would stay connected with it, and so far it has. Or atleast when it switches to "local only", it reconnects right away. I'm trying to stream movies and music to my PS3. But whenever it flips to "public", I can no long stream the files. can stay I it to set as a private network?
View 4 Replies View RelatedI am using a Dell XPS 420. I have been able to transfer files via a private network with no problems until now. I made a share folder with the correct permission. I can transfer any file under 5MB with no errors. If I send a file at 6MB it will process the folder and after 5 min I get this error message:
Network Error... There is a problem accessing C:userpublicetwork testfile name28624.zip.
It says make sure you are connected to the network and try again. Is there a timing issue causing the lost connection? I worked with Dell and since it worked in Jan 08 to reinstall the backup for the Dell Factory settings. I thought I would check with the Windows Vista Community before I do the reinstall. I also have another computer with Windows Vista Ultimate and I can transfer the files with no problem via Hamachi network.
I am running vista home premium on a dell 530 and have just had to restore factory settings due to my user account being corrupted. I have reinstalled all my software and now have realised that it is doing what It has done before in the five months I have had it (after restore to factory settings) which is waking from sleep on it's own. I did find a solution to this on a forum which is to go to device manager / network adapter / intel.... / properties / power management / wake from LAN and uncheck the first two settings "wake on directed packet" and "wake on magic packet". Now as this solves the problem I am confused as to why my "factory settings" have it checked???? Now, immediately after closing the properties window I got a dialogue box saying that a new private network has been detected with a highlighted option to call it local network2... this freaked me out as I have not connected anything to even remotely act as another network and further more there was an ip address in the bar at the top of the dialogue box which I noted (169.254.175.32/255.255.0.0) I would just like to know if this is behaviour of a virus of some sort or something normal beyond my understanding.
View 4 Replies View RelatedI have a Vista Laptop and am trying to join to a SBS 2003 Premium network. I would like to preserve the existing settings and so select the current user settings for the new network user. When I attempt to proceed, I receive a message that the User Profile Folder is set to Private. What should I change and where in order to set the user profile correctly?
View 8 Replies View RelatedPrivacy features such as InPrivate browsing in Internet Explorer 8 and similar features in Chrome and Firefox promise to protect your privacy by not keeping track of page history, temporary files and cookies. This may be enough to hide your tracks from a beginner computer user but there are still traces of what sites you visit within the local DNS cache. An advanced user can run the ipconfig /displaydns command to view the most recent sites visited....
View 0 Replies View Relatedi was having some trouble setting up an ad hoc network on my computer... (i have a vista home premium computer).. anyway, it seems that the "set up an adhoc (computer to computer) network option is not available
the options that are available are:
connect to the internet
set up a wireless router or access point
set up a dial-up connection
connect to a workplace
how do i make it so the set up an adhoc (computer to computer) network option is available? (if it helps any, im trying to set one up so i can access the internet on my ipod touch)
I'm having some trouble setting up a network in my home. Here's the deal, I've got my laptop running VistaHomePr 64 and my Desktop running XP Pro 32. I recently got a wireless netgear router. My notebook connects wirelessly through the router while my desktop connects to the router through an ethernet cable. (The router has both wired ports and wireless transmitter)
Now, before I installed the wirless router, I had the two computers networked (and working properly) through a dynex wired router. Now I'm having trouble getting them to see each other. I'm not even sure if you can network computers while one is wireless and one is wired. I just figured it could be done since it was all going through one router.
I am trying to set up a small network but having some difficulties – it does not work - I have done everything I think I should have done but still it does not work. OK what I have is two desktop machines DT (1) and DT(2) running XP Pro I think with SP2 – dont think I have SP3 and a nice four port O2 wirelessrouter which seems to be a Thomson Telecoms product and lovely new and shiny New Toshiba Tecra M10 running Vista Business. I am running ZoneAlarm as my firewall.
At the movement my main DT PC (1) is the only XP PC connected - obviously using Cat 5 cable and the Toshiba Laptop is also connected using Cat 5 cable. I did the XP set up a home network wizard and that seemed to be OK. I have set both the DT (1) and the LT to be on the same workgroup and on the DT (1) when I go to My Networks and then workgroup I can see (icons for) both the DT (1) and the LT.
I have multiple LARGE drives on the DT (1) and this is why I want the other DT (2) machine on the network to use as a fileserver – i have what must be close to a trillion pictures that i want to sort out - the work of a lifetime and a lifetimes work and i still have years of negatives to scan and sort I will then move all (apart from one) HDD’s to the second DT (2)............
I recently moved my wireless router and cable modem away from my Vista PC. It was always configured wirelessly, as I knew I would have to move it at some point. I left the computer on when I unplugged the router etc. and then set them up downstairs. When I tried to access the network after everything had been set up again, I noticed that Vista thought my home network was an "Unidentified network" but still had my ssid in (___). Only problem was that now my network is "local only". I am connected to the router as local-only, and tried to adjust my router setting via the router page at 192.168.1.1 It was returned as page not found. Is Vista confused? If I was truly conncted to the router and even if internet was not working I should be able to adjust the settings on the router,right?
I can access the internet just fine with all of my other devices in the house, such as Tivo, Ps3 and Windows mobile cellphone. All of these are able to connect to the internet through my router. There are other networks available around me, so I tried to connect to one of those. Same thing, local only. I cannot confirm that internet works on this other network. But I have narrowed it down to a problem with my Vista computer.
I cannot see a setting for the 1000Mbps Full or Half Duplex with either of the Gigabit lan's in my conputer. Thought the problem may have been with the motherboard on board lan so I installed another card. Both "auto config" both say they are connected at 1 gig into the gigabit switch. But when you go into Device manager, right click device. .properties. advanced tab. . .I cannot find the 1000Mbps listed any where under the Speed and Duplex settings it just has the 10Mbps Full & Half and 100Mbps Full & Half. Transfer rates from computer to computer remain at 100Mbps speed (7-8 meg/sec) not at 1000Mbps (35-40 meg/sec I was getting with XP) as connection lights are showing.
View 5 Replies View RelatedWe have a network of 5 vista machines, 3 xp machine, 7 voip phone and 1 network printer. The internet of all 3 windows xp machine keeps on dropping once everyday, removing the ethernet cable and putting the cable back doesn't help it, restarting the system doesn't help it, refreshing the ip doesn't, restarting the router either, the only way I found to give them internet again is to manually set the ip and dns configuration daily.
View 6 Replies View RelatedI just got my Vista 64bit laptop working wireless with my WinXP desktop through a Belkin router. I can transfer files using either PC and can print from the laptop on the two printers connected to the desktop. IOW, I can do everything I need so far.
When I open Vista's Network and Sharing Center on the laptop, I see the SSID name that I'm connected to, with "Public network" next to it. Is there any reason I should change it to Private? Either way, could someone please explain the pros and cons of having it set to public or private?
i am using windows VISTA recently and i don't know how can i setup something in it and my question is: when i leave my computer it goes to sleep mode and when i back to my
computer and hit a key or move the mouse windows opens the computer but i need that windows first ask my username and password and then open the computer.
It has happened occasionally, but with no predictability that I can see. I change settings in control pannel / power settings / balanced to 10 min for monitor and never for computer. I check the "advanced settings" to assure that they are the same. I use balanced because that seems to be the default in the registry. I do not see the actual settings in the registry. Every so often Vista resets the settings back to 20 min for the monitor. I have looked at but it speaks of "System Settings page" - I don't know what that is. In any case, my settings have no effect and I can't get the monitor to dependably go to standby after 10 minutes.
View 7 Replies View RelatedI have been asked by my company to evaluate Vista Buisness for use in our company. All of our laptops are purchased from HP and as of a few months ago come with Vista OEM licenses so licenses are not a problem. But as soon as we receive a new laptop it is imaged with XP removing the original windows vista installation and recovery partition. So we have no copy of Vista oem. Does anyone know a place I can download Vista OEM, (Note I only want the files don't want a pirate copy) which I can use with our OEM key.
View 4 Replies View RelatedI have three desktops and a laptop connected to a linksys router connected to a comcast cable box. The comcast system uses a WPA encryption which cannot be changed to WEP as they do not use WPA. I have system 3 shield (iolo) system guard, antivirus, firewall, and the Vista ultimate firewall turned off. I see an unknown computer named FISHY (IP 192.168.1.139) with unknown gaming files on my home network. I have renamed the network on all of our computers and still this unknown computer shows up using MSHOME. I've enabled the Linksys router to acept only the IP addresses our computers, and to deny the IP of FISHY to no avail. How do I remove the FISHY computer. If I turn off the file sharing or discovery all that does is make the FISHY intruder become invisible but they are still there on the network. The shared files on FISHY say Desktop.ini so they are hacking into my system, how do I stop?
View 4 Replies View RelatedFrom what I am told, Cisco VPN client will not work with Vista and it is Microsoft's fault. Can you shed some light on this? Cisco is pointing the finger at MS, but it is their software that is causing the problem. Start Before Logon and Microsoft Certificate with Private Key Protect Fails Trying to connect the VPN client using Start Before Logon (SBL) and Microsoft Machine-based certificates fails. This is a Microsoft issue, not a VPN Client problem.
View 5 Replies View RelatedWhen I put e.g. documents in my publick folder, do they appear automatically in the private folder too? Do I really need 2 folders to see all my docs in vista?
View 8 Replies View RelatedWhen I receive email the text is there but the pictures are not. Sometimes I get the red X and other times nothing. But if I do a select all the blank space turns blue as if something is there. When I get mail from ex. USAJobs, the entire body of the email is blank. Some others the text directing me to "having trouble viewing this email click here" and then it takes me to their website. I have the block pics box unchecked and I am running vista with PCTools Spyware doctor. Also email from friends and family the pictures show up with no problems. The only problem I am having is from commercial sites. And yes I even added them to my allow list.
View 8 Replies View RelatedI'm using Vista Home Premium and Windows Update tells me I'm up to date.
Every so often the Network icon in the System Tray tells me that it is not connected to a Network (by displaying a red X) though I can clearly see that I am.
I'm trying to network my new Optiplex 740 with Vista Business (32bit), and Norton 360, to my old Euro PC with W2K Pro. and SystemWorks, using basic Belkin /Realtek cards and yellow ethernet cable. My broadband connection is through my old machine and works perfectly, as does the network card installation.
My new machine also indicates that its card is correctly installed and functioning correctly. BUT the Network and Sharing Center window shows this computer as linked to an Unidentified network and no connection to either the other computer or broadband connection.........
I have bought DD a laptop for Christmas and thought I'd get it all set up beforehand. I already have a wireless network here at home, with 2 desktops running xp) and a macbook, they connect via a belkin wireless modem router. Vista however, doesn't even find a network, I get a message saying the network cable is nplugged. Its wireless enabled and the switch is on
View 9 Replies View RelatedOne usb ethernet adapter for internet connection through an old router, one for a Linksys Wireless G router hard wired to remote security cameras sums up the problem where one cancels the other out. This is a problem for XP, Vista, and even 7 beta while the primary system still runs XP. The dsl connection is through an old dsl setup using a usb adapter while the Linksys pci adapter card or usb adapter once installed becomes the default network adapter.
The wireless router itself is plugged with the RJ-45 ethernet adapter directly into the main controller/dvr box for live wireless feed to the main XP system or this one as a second means along with direct plug in to a tv set in the room where the main box is located. In XP, Vista, and even the later 7 beta the same problem of running two adapters without conflict is the main question needing a working solution. This thread is intended to tax the most network familar people here.
The landlord runs the main XP system with eventual plans to upgrade to Vista while this system serves as a testing machine a good deal of the time explaining multiple OSs as a rule. The router and adapters are in working order not seeing any defects while canceling the original dsl adapter out when installed. That takes out the online connection in the process.
Bought a Freecom Network Drive (LINK) from PC World today and got it set up and it seemed to be working fine on my Vista computer until I tryed to get it set up on my XP computer. It seemed to get setup ok but then the whole thing just stopped working. The hard drive spines and it works fine when plugged in as USB device but when trying to connect it to the network it simply does not show up. I have a Belkin G+MIMO Router and the Network Hard Drive is a Freecom Network Storage Hard Drive 250GB
Can I set up network of two computers with Windows Server 2008 and Windows Vista Home Basic with FireWire? How both systems will detect connection of two computers with FireWire cable? Does that connection make possible file exchange?
View 6 Replies View Relatedbuilding my rig that I can't stop! So I have a second EVGA GTX 260 on order. Any hints or tips on get SLI up and running?
View 6 Replies View RelatedI am looking for a registry tweak that will allow me to change the default Vista theme to the Windows Classic theme. I want do get the registry entry so I can apply this to multiple machines in my domain using a logon script. Please dont' tell me to go to Control Panel > Appearance and Personalization. I know to do that. Just need to know the key(s) I have to change to make it permanent for every user who logs on.
View 4 Replies View Related