I have a problem I have a new system installed Windows XP professional. Everything was ok till yesterday. I just have a few more things to install and I have the computer plugged into the 4 plug UPS so if the power goes down the computer has 5 minutes to shut down. Well the hydro went off yesterday for a few seconds and all of the other computers came back up but the new one. It was booting into Windows got to the Windows logo and the bar going across loading then after 10 minutes still sat there. I decided to re-boot to see what was wrong as I am a computer tech. Nothing so I went into safe mode that was fine got out of there same thing logo looks like it was starting nothing. I did put in the Windows XP disk thinking to just do a repair still the same thing. I get the Windows screen like it is loading nothing. Go back to safe mode and here is what it says and there is no disk at all in the drive. Can not run setup from Safe Mode rebooting computer.
computer for a few days you would press the start button on the tower and it wouldn't start right away but then after a few sec would come on. Yester day I tried it twice I pressed the start button on the tower and you could hear the power supply try to start but would die and the computer would not come on. so about the thired time press the button and nothing, would even try to start. I figured it was the power supply. I put a tester on the power supplyh and it said it was bad, so I bought a brand new one put it in and it still would n't do anything just dead.I tested the new one and my tester sasid it was bad, I changed it for another one and the store I bought the 1st one from tested the 1st one and there tester showed it was good, so my tester must not be working.
We are trying to start a laptop but windows is not starting up properly. As the boot begins, it takes you to a screen that says, :"if a previous start up attempt was inturrupted due to a power failure, then choose Start Windows Normally". We follow the directions, takes us the Window XP screen trying to boot it up and then takes us to the Gateway screen and then back to the screen where it asks the same question again.The cycles continues without any other options.
Or at least I think so, there was a whopper of a lightning storm and then Windows wouldn't start up the next morning. I've been trying to trouble shoot and am at a standstill close to the answer.
It will start in safe mode I cannot restore it using the disc I disabled several things in device manager and that didn't help I tried the repair from disc as well, doesn't work I finally reformatted - still doesn't work.
My PC has old configuration, the Max Power Supply can be only up to 350W. You know that every parts of the PC, either external or internal hardware will consume power. What I would like to know is that, what would happen to my PC if the total power consumption exceeds the MAXIMUM VALUE of the power supply unit.
The Memory has been tested by PCClub and has passed the test this memory is new and fresh so nothing is wrong with the memory.What im thinking is that its the power supply because i didn't get the Power Supply my friend got the power supply at the Thirft Store (the name of it is what it is Thirft Store) now i didnt think it was messed up because it was in package and all wraped.I have some pictures but NOTE: The Pictures are when i was useing the CPU from a Compaq Presario so dont pay anything to that.
Can i rebuild with a different power supply, and even into a new case with all the other bits i have?? or do i need to start from scratch. I ask about the new case, as i'm in desperate need of more drive space (cd/dvd etc)
I brought a 400watt power supply from eBay it has the sticker on the side that lists the power but i want to make sure that it can actually give 400watts because i know that it isn't too hard to change the sticker or change the case and replace the internals with the internals of a 250-300 watt PSU are there any tools that i can use to check if the power supply can give 400 watts? it is a PSU made by ultra.
I have been using a "Raidmax RD-350W" power supply with a 20-pin connector to the motherboard. When i bought a new power supply it had a 24-pin connector to the motherboard. Here are a few questions since I know nothing about PSs. 1. Is there a designation (besides just manufacture preference) between 20 & 24-pin connectors to the motherboard (i.e. Pentium vs. AMD.I use AMD)? 2. Can I just buy a connector from the 24-pin connector from the PS to the 20-pin connector on my motherboard and not adversely affect my computer's power.
I last night I turned off my computer for the night and this morning it wouldn't turn on. I checked the power cord and the power strip and everything looks fine. It looks like I have to replace the power supply unless someone has other suggestions. My question is, since I may have to replace my power supply, is it safe to replace it with one that is more than twice the wattage of the one that's in there now.
Back up Hard Drive into mine as he wanted to reformat and install OS. back up successfull, i took his hdd and put it back on his own motherboard to format and install an OS. As i on the switch, a burnt smell from the power supply reached my nose. the pc did not start at all.My PC's power supply is 450watt and my frend's PC's power supply that was burnt was 350 watt. Why did the power supply burn?
I'm looking to upgrade my video card, but I need to find out what watt my power supply is. It is a Sony Vaio Model # PCV-7752, although when i try and locate the model at www.sony.com It is not listed. I open up my computer sliding off my side panel, yet there is no wattage listed there either. Any suggestions as to how i can figure out what my wattage is?
I recently put together a new computer. I have used it for about a week now, today I got home and my computer won't turn on. I am guessing bad power supply but wanted to check if it might be something else.
The mother board that I have is a Biostar K8NHA GRAND Socket 754 ATX Motherboard, DDR400, 1394, SATA RAID, 6ch Audio & GB LAN
The best solution to most issues with looping is POWER SUPPLY. Due to the huge amount of resources that video cards, sound cards, larger cpu's, they suck your power supply to the point that application cant perform. In turn it causes lockup, reboot and boot to desk top.A lot of resellers are only slapping in a 300watt power supply in newer systems. That doesn't work, you need at least a 400watt or greater. You need at least 450watt POWER SUPPLY. Take my word on it.This is the biggest issue i have studied on the net and in my lab for 1 1/2 years now. So many people have taken components back to the stores had them tested, to find out there is nothing wrong with them and go around shaking there heads in wonderment, without even considering power supply.
I have just upgraded one of my old Windows 98SE computers to XP Pro. The installation went well.But, for some reason now after I shutdown the computer in order for me to turn it back on I have to unplug it from the power supply and then plug it back in. Before i upgraded the computer I was already having a shutdown problem with Windows 98SE.Every time that I would shutdown, it would restart on its own.I tried to trouble shoot the problem.I even downloaded a patch from the Microsoft Website but it still didn't work.So i figured if i upgraded it to XP it would solve the problem, but I ended up with a different problem.
This is an IBM think center with XP Pro. Symptons are random shutdowns and restarts, and constant freezeups. I checked the power supply and it smelled like it was burnt so I changed it. I replaced the HD with a new 40 gig Hard Disk and when I went to load OS it got as far as "checking system configuration and then it freezes. I cant format or reload OS.
I recently purchased a new graphics card (name in the title) and I installed it and I got an error at startup explaining that I did not have sufficient power supply so it lowered the power of the card.. it said something about adding power cords(that came with the card) but I don't know where or how to put them in
i use my geforce 8800 gts with a 450watts power supply wich do have only 4 pin connector instead of six. or shuld i wait till i get a power supply with a six pin. will i not damage the card if i try to use the 4 pin connector with this card?
I had an ELECTRIC POWER FAILURE during the start of Windows 2000 Professional this morning. After it, when I try to restart my computer, it begins to load Windows, but I receive the famous blue screen. The error code is: STOP: 0x0000007B (0x8243D030, 0xC0000006, 0x00000000, 0x00000000) INACCESSIBLE_BOOT_DEVICE I tried with F8 (last valid configuration, etc of the list), but all give the same blue screen. My repair floppy disk is from september 2007. After it, I installed a second HD for files backup and needed to put drivers for Windows recognize the bigger HD size. All worked fine until the power failure this morning. Antivirus and scan are up to date. Since I installed the driver for the bigger size HD, I cannot more boot through the floppy disk, because it not recognizes the HD. Is there anything I can do to not reinstall Windows?
I have a question regarding my PC and some problems that I have been experiencing, which I think are related to my power supply.
First off, my PC will not recognize my iPod Shuffle. When I first purchased the Shuffle, everything worked fine, however one day when I went to plug it into my USB port, nothing happened and the orange light on the iPod flashed. I tried all the USB ports, including the ones on the back of the machine to no avail. This is not a problem on other people's machines, where XP is able to recognize the external device.
Also, whenever I go to shut down my computer, the light on the front of the tower is on and the fan is running. It is like the computer is not even shut down. I have to manually turn off the power strip everytime I want to shut my computer off. Also, "Stand by" is not an option on the XP menu.
I've been told this is a power supply issue. Anyone have any other ideas?
Ever since a power failure yesterday, my computer is not booting 100% of the way - it seems to stall at the end after loading desktop etc, can't see anything missing but I am unable to do anything. Nothing opens when clicked on. It works perfectly in Safe Mode with Networking.
I checked Device Manager and found 3 things highlighted:
HID Non-user input Data Filter
HID Non-user input Data Filter in HID section, and
WAN Miniport (IP) in Network Adaptors.
I do not have a wireless network, only a hard-wired one, so not sure what that is about.
The computer shut down due to a power failure in the house. I started it up and the windows loads OK till I get to the page where it has the users names listed. I click on any user name. When I click on the name, it opens the page for a second and shuts down. I can see the wallpaper of each user and it closes immediately. It reads LOADING PERSONAL SETTINGS and then it reads LOGGING OFF, then it says SAVING YOUR SETTINGS.
During an installation of XP we experienced a power failure.The installation had been running for about 8 minutes when power went out.I After electricity was restored, I attempted to reinstall XP on the laptop however, now it will get to the Windows horizontal bar screen, and then a Windows Message comes up and says The system is not fully installed.
I was on the computer this morning (plugged into a power bar) when all of a sudden the power went out in my neighbourhood. I was just on the desktop at the time I believe. I unplugged everything to prevent anything from surging to be safe, and I went out for the day.When I got home, the power was back on, and so I plugged the computer back in. However, as I plugged in the computer, it turned on by itself. Normally it does not do this when I plug it in after it was forced to shut down for a blackout. I immediately knew something was up.When it started to turn on, it immediately went to a blue screen of death.
It won't get past this screen. I've tried Safe Mode, Last Known Good Configuration, Normal Mode and it just keeps going back to this screen. I also noticed it doesn't make the normal noises when it's booting up. It doesn't make that 'click click' sound when I'm booting up (I believe that's a hard drive sound?). I do have access to the Windows Recovery Console (I think - it appears as an option - I don't know if it will work) but I don't know what to do. It sounds like it did something to the hard drive... when I boot up the computer normally it asks me to press F1 (because my CMOS battery is low)... now on that screen it says Serial ATA at the top. I don't know why that is, or if this has anything to do with the low CMOS battery before, but I can't get it to turn on at all at the moment. I don't understand why the power failure would do this (or what it did)... I've never not been able to boot up after a power failure. And surely there wasn't a surge since it wasn't plugged in when the power came back on.Did it kill the HD? Anything I can do to at least recover some files?
My power went out for ten seconds yesterday, and when my desktop re-botted, it says drive D (hard drive) needs to confirm file consistency. It then performs a check and says all is well. The desktop then appears and the whole computer freezes. Anyone have any ideas on a fix? I have Windows XP with SP2.
I was on-line several nigths ago, when the we suffered a power failure. Since then, everytime I try to use the modem(covenant 56k), I get a message indicating the port is in use by another program, and the dial-up attempt is aborted. I have re-installed the device-drivers for the modem and the port(COM1 -modem acutally is uses COM3), but still get the same results.
can anyone help we had a power cut whilst my daughter was using her computer which runs xp.Now when we restart it it just continually restarts, I tried pressing f8 at the welcome screen and started in safemode this made no difference just went to the welcome screen and started again!
I have a windows 2000 server crash. Assumed I had a power failure this weekend. The monitor also died. I replaced monitor. I hear the computer start up. Power to system, but no visuals.I do have a boot disk made on 3.5 floppy disk. What are some simple tips or things to do before I begin to restore the system.I have checked all power cords.Computer is AMD with raid system unsure of rest.
My PC starts up fine, BIOS all OK. Then I get the message about Windows failing to load because of possible power surge or hardware problems or something, and a choice between loading Windows normally, loading the last known working setup, or the three variations on loading safe mode.
