I am running windows XP Home edition with SP2. When starting up it stalls at the XP splash screen with the flashing bar below it. I can start in safe mode but haven't had any luck with the system restore.
View 1 Replies
My son has a Dell dimension XP. It wont boot past the windows splash screen. We can get into safe mode, from there we have tried system restore. It did the restore but still wont boot up into windows. We have also tried chkdsk /f and /r but it tells us that the system is in use by another process. We have disabled the startup up progs, and tried again but it stills says the same. OK so we tried using the xp installation disk, changed the bios to boot from CD Attempted to do REPAIR, but it said ' set up did not find any HDD installed in your computer.
View 5 Replies View RelatedMy machine runs fine for a bit then starts to stall and the screen goes black for a few seconds. After an hour or so the computer then locks and needs restart.
View 5 Replies View RelatedI am using WinXP SP2 and just two days ago the computer stalls at the loading screen (black screen says Windows XP and the blue loading bar underneath). It doesnt completely freeze but it just keeping on loading and never gets to windows, even after I wait for 10 mins. I have tried F8 and used 'last know good configuration and that didn't help'. The only change that i've made was instaling a new DVD burner a few days and it worked no problem after installation. The stall problem started after I manaully shut down the computer (press down power for 10 secs) when my computer froze from using dvd shrink. I'm pretty sure its not the software problem.. it should be hardware problem? Should I update dvd firmware? Is there anything else I can do to fix the stall problem?
View 3 Replies View RelatedHaving suffered 3 HDD failures, I have cloned my laptop hard drive (XP Home edition) with Norton Ghost 9.0. I have copied the MBR as well and made it active. Replaced the laptop drive with the cloned drive, but it only boots up to the XP light blue screen and stalls.
View 6 Replies View RelatedVery similar to the following problem but i do not have a raid, and it seems that this PC has a raid and i don't, plus it was never really determined what the actual solution was.
http://forums.techguy.org/windows-nt...oot-black.html
The basics: XP Professional Boot up screen, right before the windows loading screen, or direct after the F8 Menu if you hit "Start Windows Normally..." it will just lock up, no HDD activity, blank screen. now BSOD, nothing.
All 3 safe mods work fine.
Ran chkdsk /r in recovery.
Ran proper fixboot procedure.
Went into safe mode and checked the event viewer.
The only concerning message i got was: The following boot-start or system-start driver(s) failed to load:
AmdK8
Fips
nod32drv
Formatting really isnt an issue since i can back up anything i need through safe mode. However its just the fact that the Windows gremlin has struck me again and i must defeat it once more.
I highly doubt this is a hardware issue as it is more of a driver/software issue.any help?
i'm having to boot into windows xp. on power up sytem goes through the windows xp splash screen (with progress bar) and then instead of login prompt it goes just into the blue screen with moveable mouse pointer arrow.
issue seems to be similar to:
http://forums.techguy.org/windows-nt...o-startup.html
http://forums.techguy.org/windows-nt...p-problem.html
but recommended solutions didn't help so far.
symptoms just before issue - was not able to run use some system features - utility to turn off the display, utility to bring up battery info - everything was working fine before this
what i've tried:
boot to Last Known Good Configuration - resulting in the same blue screen
boot to Safe Mode / Safe Mode with networking / Safe Mode with comman prompt - resulting in blank (black) screen with "Safe Mode" in the corners and moveable mouse test the hardware (hard drive / memory etc.) via build in PC Doctor - all seems to be working
i am able to use bootable XP CD from other machine to get into Recovery Console
i am able to boot to simple live XP using BartPE-XPE usb key and access the hard drive
Was working fine this morning but this afternoon - Upon startup everything runs fine until after the windows splash screen everything goes black and the only thing visable is a cursor, but nothing to click, cannot ctrl=alt=del, cannot right click. Cannot enter safe mode at all, last good configuration doesn't work either. Computer is still running, fan whirring, lights flashing. Fan has been cleaned and power supply checked, no change. Cannot get into anything to run explorer or virus check. She is running Windows XP SP3. I'm unsure of when sp3 was installed. I understand this may be an issue, along with video and graphics drivers, display settings, corrupt registry, flat CMOS battery or loose internal connections.
View 3 Replies View RelatedIve done a fair amount of searching online and tried a number of things myself, needless to say, they didnt work.Ok, so here's the issue; When I go to turn on my computer, I make it to the XP splash screen with the 3 blue bubbles moving left to right... But nothing from there.Additionally, between the BIOS screen and the XP splash screen, theres some weird black screen with what looks like a long barcode-esq bar, where a solid white line fills the gaps moving left to right...
View 3 Replies View RelatedHow can i change or remove it?? can i do the same with the shutdown screen?? also does anybody know how to get rid of i.e.s icon?? i use avant browser.
View 2 Replies View RelatedI boot my xp machine but it hangs at the xp splash screen.It's not like it's frozen, the blue bar under the "windows" just scrolls and scrolls and scrolls, etc. The same happens when I try booting to VGA mode.I am able to boot to safe mode, just not completely. I get to a screen that says " Safe mode Microsoft (R) Windows XP (R) (Build 2600.xpsp_sp2_gdr.05001-119: Service Pack 2) Safe Mode.I can also see the mouse moving around, just nothing else. Nothing was added, removed or installed.
View 6 Replies View RelatedThis problem started several days ago. On restart the XP splash screen loads but freezes as the progress bar is in motion. After rebooting several times it does load to the desktop, but on restarting again it hangs.
I have searched reference articles, forums, etc and have found others have the same problem and have narrowed it down to nvidia drivers and hardware conflicts that load after 'mup.sys' in the boot up process.I had installed a nvidia graphics card and driver before this problem began but then uninstalled, deciding to keep the on board sis igp. I have downloaded driver cleaner and removed all traces of the nvidia driver but the problem persists..I am running XP sp2, p4 3ghz, foxconn motherboard, sis 661fx graphics.
My PC has developed a problem and I'm looking a solution. What I'm seeing is that when I boot my PC, it gets to the splash screen and I see the scroller moving but that's it. No color changes no BSOD, etc. At this point, I've been able to restore my system using an Acronis full system recovery but I would like to know what's going on behind the scenes when the progress bar moves but nothing.
View 3 Replies View RelatedI'm getting a BSOD. Everything seems fine--it is at least getting to the boot.ini since I get an OS selection--W2K or the Recovery Console. The W2K splash screen comes up, the blue hash marks scroll about half way across the bottom, halt, then BSOD "INACCESSIBLE_BOOT_DEVICE". I tried the Recovery console, but that BSODs as well. I used ERD to run CHKDSK --- no errors. Possibly the hdd? ERD took a loooong time to read what OSs were on the hdd--five minutes.
View 1 Replies View Relatedi used it all fine about 2 hrs ago and shutted down fine. i just now go 2 boot up and after i get the BEEp, bios screen, it says vereifying dmi pool data for a split ssecond and gives a blak screen for a split and does the Splash. but my issue is, it doesnt give me a splash...it just sits at that blak screen.
View 3 Replies View RelatedWhen im tryin 2 start her up, after the splash scr een l oads, just as it enters the next stage of boot up it flashes a blu screen and reboots. i cant boot under ANY start up options.
View 7 Replies View RelatedI am new here and I consider myself very knowledgeable on a computer but this one has me pulling my hair out. I have seen posts for similar situations but nothing identical to mine. What I have is a Dell E520 and we had a power serge and the computer shutoff. When the computer was turned back on it P.O.S.T. fine, loaded to splash screen and then once that is done loading I get a blank screen. Nothing. I reset go to safe mode, works fine, loads into safe mode. I try to load safe mode with networking, will not work. So I went back to safe mode and tried to do a system restore, told me it was disables and I would have to go back and enable it in regular mode.
View 3 Replies View RelatedI have a Dell Dimension 4600. I got a new 80gb hard drive and wanted to clone it with the current 20gb drive. I took both drives and connected them to a different pc that had norton ghost on it. After cloning, which went fine, I placed them back into the Dell with the 80 gig set as master, and the 20gb set as slave. The computer would post normally and boot to a black screen with a blinking cursor, this happned right after verifying dmi data pool. It would hang at this screen never getting to the windows loading screen.
I returned the 20gb to the master drive and set the 80gb as the slave. It booted fine. After getting into windows I saw it was reporting the 80gb as C: and the 20gb as D:. I changed the drive letter of the 80gb (in safe mode) to G:. After changing it the computer would freeze at the XP splash screen, however I still had control of the mouse. I believe this was caused from windows search for the page file on C: which no longer existed............
my PC that the screen goes black at the XP Home splash screen. When I boot into the safe mode I get to the login screen then the screen goes black.
I have removed and replaced the video card and also tried using the VGA mode. Same problem. Any thoughts?
Today, I tried to start up my XP computer; it gets to a splash screen saying that the motherboard is optimised for the Intel-P4 combination (which always pops up after POST and before the system boots up) and it just stopped. Rebooting encounters the same problem.I can't boot from floppy, CD, or DVD drives, and cannot get to the BIOS setup (hitting the appropriate key just gives me a blinking cursor on a black screen with which I can't type).There is obviously something seriously wrong, but it's beyond my very limited skills.
View 8 Replies View RelatedI copied my laptop hard drive with Norton Ghost 14 to a larger HD and installed it onto my Dell Inspiron 9300. It starts with the Windows XP screen with the loading progress bar and gets to the blue screen with Windows XP and just stalls, won't load. I can get it into safe mode but it gets to the same splash screen and stalls again.
View 2 Replies View RelatedI had to switch my pc off before shutting down properly earlier today. Each time I attempt to boot, I get the message windows did not start properly etc. and I am given a choice of whether to start in safe mode, last known setting that worked, or normally, etc. When attempting to start normally, I get the windows xp splash screen whith the progress bar for a few seconds, then at the point it would normally switch to the blue password prompt, the screen goes black. No error message, no cursor, no nothing. The system just hangs. It does exactly the same when I try 'last known settings that worked'. On trying in safe mode, the list of drivers it is attempting to load comes up, fills the screen, and then just stays like that.
View 9 Replies View RelatedI recently had my motherboard changed on my Intel Pentium IV 1.6 GHz PC due to some serious problems.Now, I'm again suffering from problems. Once I boot it, POST is displayed, and the Windows splash screen appears. Very often, the screen goes blank. It seems that everything else is working. If I press Alt+F4 followed by a 'u' (To select the 'turn off' button), I hear the Windoze shut-down sound and the computer shuts down.
View 3 Replies View RelatedI downloaded and registered VMware Server so I could make my own virtual machines. I was planning to try Ubuntu and Solaris. VMware made my Ubuntu virtual machine so then I tried to install Ubuntu on it using the alternate CD (I didn't have the live disk on hand). The install went fine for a while, but eventually the screen started to blank, return, and blank again. Finally it blanked and wouldn't return. I saw the Ubuntu workspace switcher in the lower right-hand corner and the Ubuntu logo in the upper left-hand corner, but everything else was black. I tried to do a ctrl+alt to jump back to Windows, but the VM screen shrank and parts of the windows I had open in Windows showed up, but the screen was mostly white.
View 1 Replies View RelatedWhy on the XP splash screen does it not say professional after you update to SP2? It always used to say Professional?
View 4 Replies View RelatedI switch on my PC, it starts ok till the Windows Welcome screen. I hear the XP intro music then there's a 3 second pause, then a short beep, another 3 second pause, then another short beep, and then another 3 second pause followed by another short beep. Then the PC continues on to the desktop, and it seemingly runs ok. I regularly run Adaware, Spybot, Spyware blaster, CWShredder, and Microsoft Antispyware. everything comes up fine. I have PC-cillin 2005 on my system and that is checked regularly. Now I don't know if this is a coincidence or just what, but when I first heard the beeps, I thought to do a system restore back a month or so, but the system restore had been turned off. Now I know that I didn't do it, and no one else uses my system, so I don't know if that has anything to do with the beep problem.
View 1 Replies View RelatedI have windows xp sp2 and after the splash screen the system hangs for about 1-2 minuets then reboots, i don't know the problem, i can not log in so i can't fix the problem either, so i need to know if i have to reload xp or if i just have to do something else.
View 5 Replies View RelatedI have a friend's laptop that boots up and goes to the XP splash screen with the dots moving and they just keep going and the laptop does nothing.
View 3 Replies View RelatedI know I have seen this talked about but I cannot find a resolution. I have a new HP Pavilion desktop PC that has Media Center 2005 installed with all updates from Microsoft. It has the following hardware, etc:I recently had to replace the internal Media Card Reader as it had failed. Last night I tried to start it up and it kept hanging at the Windows XP splash screen with the blue bar scrolling left to right. It just stayed there and would not go further. I then booted up to Windows XP install CD and entered the Recovery Console to start CHKDSK /R which it completed successfully. However that did not solve anything. I have read that Windows is loading drivers, etc. under this splash screen and it more than likely is trying to resolve an issue with one of those.
View 14 Replies View RelatedI started up my system today and on the windows splash screen (the page on start up that shoes the WINXP logo and the blue scrolling bar below) The blue scrolling bar was stuck in one place and stayed there for a good 2 hours so I restarted and was greeted by the infamous ?Disk boot failure, Insert a system disk and press enter?. So I turned off my system and took the side of the case of and disconnected the SATA cable from the hard drive and then the power cable from the hard drive as well, connected them back up powered the system back up and I am now back on the windows splash screen. With the scrolling blue bar below the WINXP logo stopping and starting randomly now and again. I am going to leave it for 2 hours see if it recovers its self, anyone got any ideas if this does not work what to do? I have my windows XP disk and serial number so I guess its fresh install? Still what could have caused this as it?s happened twice now!!!! Could it be the SATA drivers I have all the driver installed by a shop do I need to install SATA driver for the HD or not could the drive be faulty?
View 14 Replies View Relatedi just installed a WD Raptor drive and trying to install Windows XP Pro...the install went fine - and my BIOS configurations are set for RAID bootup. I have my other hard drives disconnected and it still wont boot. I have even gone as far as finishing with the Activation/Serial # and user name but when i restarted it boots up and runs through POST fine but the Windows Splash screen --indicating that windows is loading-- doesn't pop up. i know this sounds like i've just done something dumb but i have built several computers and this one is just kickin my.
View 1 Replies View Related
