Partition Magic Error 58 Cannot Write To Boot Sector
Sep 9, 2007
Windows XP .I am trying desparately to enlarge my c drive, which is partitioned from a large drive also containing f (programs) and g (data) drives. I need to enlarge the c drive to allow proper cmptr operation.i used Partition magic , which seemed to work up until the point where it rebooted and gave me error 58 "unable to write to the boot sector. Virus protection software may be running. "I have disabled Norton Anti virus, and Spyware Dr (complete shutdown). Still no success.How do i disable virus protection in the boot.
View 6 Replies
ADVERTISEMENT
Sep 25, 2005
does anyone know what will solve this annoying error that frequently disrupts the bootup of windows XP PRo? You can run Chkdsk from savemode and this solves temporarely the problem but time and again after shutdown this error reappears. Somewhere during shutdown it seems that the filetable(MTR?)is corrupted Partition Improperly Unmounted Error 1516 is the message.
View 7 Replies
View Related
Aug 22, 2005
I installed PM 8.05 and used it to resize C drive (WinXP OS is there).I used the auto function to take a 1Gig amount each from drives D, E and F (about 25+ plus Gig free on each of these on a Seagate 120Gig HDD) to add to the 1Gig of free space on the C drive. The PM process seemed to go OK (went into DOS(?) and went through 7 steps to resize, etc) as there were no error messages. It said at the start it was going to do FAT 32 which is what I had the drives set up as. At the end PM said it was going to reboot and then the fan was hit. The boot up stopped at the "DMI Verifying Pool Data" message and the little line cursor just sat there blinking.
View 12 Replies
View Related
Mar 4, 2006
I have a toshiba laptop running windows xp. It crashed yesterday and now whenever it boots it give me the following error A disk read error occurred Press ctl alt del to restart.I managed to get to the selection of boot in safe mode, but it still won't boot and then I get I/O error reading boot sector.At this point I just want to get the data off it. Toshiba's recovery disk only has the option of formatting the disk and restoring the system to it's initial state (the Toshiba tech support explained that was a benefit, getting it back to the original state
View 2 Replies
View Related
Jul 25, 2005
My existing C: drive. First I was getting the "Error 983" error. Then I un-installed SP2 which was causing a gang of problems, freezing programs for a couple mins mostly. After I got it uninstalled I did a disk defrag, then a chkdsk /f. Now I have partitioned the drive using PM8 again and this time after the reboot it is telling me it is completed but once Windows XP reboots there is no new partition.
Im trying to install Suse Linux 9.0. But I really want to have 2 new partitions, one for Suse, and the other as a back up.
View 5 Replies
View Related
May 1, 2005
I had perfectly working PC with XP Pro installed on a 160Gb Maxtor HDD.For no reason I error checked the hard drive, which the system did after rebooting, at the end of the test the system rebooted and announced that there was a error on the boot and boot.ini.Useing XP Emergency (on disk) I tried fixmbr which did nothing then I tried Fixboot. XP found the drive identified it as FAT and said that it was successfully fixed.The drive was FAT and is now unusable.Partition Magic sees it as a FAT drive as does XP when I switched the HDD into another machine.
View 4 Replies
View Related
Aug 10, 2005
I was fiddling with my usb flash drive in disk management and i accidentaly deleted my data partition! I thought i was deleting a badly marked flash drive sector! All my data was on it, i have no backups!lease tell me there's an easy way to rectify this! Please! The disk wasn'torking it didn't sound like data was being deleted please tell me it's just somehow marked as not there or something!
View 21 Replies
View Related
Sep 8, 2005
I've just resized a partition on my main physical drive, and the OS sees the adjacent partition as unfromatted.
I'm using Partition magic pro 7 and WinXp pro.
The partition I resized is the primary OS partition which is formatted as NTFS, the adjacent partition is FAT32. How can I get XP to recognise the FAT32 partition again?
View 2 Replies
View Related
Oct 22, 2007
I was just using my PC this weekend and i tried to combine the 3 partitions in my master/primary hdd with my parition magic 8.0. After partition magic was done on its job, pc rebooted and i cant load xp anymore. have tried removing small battery, reinstalling with recovery CD and still wont load xp. i was getting diffrent things on the screen. first was that my pc hung on me when "booting to CD:" came, did something and next i got was mbr error 2, then i got disk boot failure after playing around with the PC.by the way my pc had acronis too. i figure it has something to do with it. i tried my recovery cd 3 tiems and after finishing the reinstall i still cant boot. i tried to use an xp boot disk and found that all my files are still intact and havent been reformatted.
View 6 Replies
View Related
Dec 25, 2004
I bought a Seagate 169GB Barracuda Hard drive and set about partitioning it with Partition Magic. Initially I was being advised via phone by a friend in a neighbouring country. I put the Seagate as the Master and my previous Master as the slave. (a Maxtor 30 gb hard drive partitioned into 3. IE ..2 x 4GB and one 22gb partitions.......these were configured C (4gb) had the OS Win 98 SE on it ...E (4GB) was a back up? and F (22gb) was for video files mp3,s etc) I put Partition Magic on C and proceeded to follow directions. To cut a long story short. I got the Seagate successfully formatted.
BUT
I have done something wrong. What happened was the E and F partitions on the Maxtor combined and showed up as unallocated space on Partition magic and Free Space on XP,s Disk management...Naturally I removed it till I got some advice on what to do.... I have since tryed three disk recovery programs and had a certain amount of success with one program .....I note however that from memory all the recovered files /folders are from the 22gb partition and none from the 4gb partition that combined with it.... I still have some options to try but as a beginner I thought it best to see if anybody in the forum with experience in this field could give me their advice so that I can hopefully recover as much as I can..
View 14 Replies
View Related
Feb 2, 2006
Cannot get Partition Magic * to installon my Windows XP computer.
View 12 Replies
View Related
Apr 5, 2008
I was partitioning my C drive of windows using partition magic so that to install Linux. my laptop(hp pavilion dv5000) had only 1 partition so I tried this stupid thing. Unfortunately power went off during partition, and now I m not able to install windows XP neither from recovery disc or from regular xp cd. Some linux (suse, fedora) and windows vista are installing fine. But I need XP disparately. What to do.
View 14 Replies
View Related
Aug 18, 2006
i have a acer t135 sempy 3300 w/ xp home,Ive tried to convert partition to ntfs its set as this 72.6 fat 32 on (c: ---and 73.4 ntfs on (d: i had a copy of partition magic from a guy at work but when i tried it i wiped hd and had to use acer restore discs
View 6 Replies
View Related
Feb 22, 2006
i have a major problem. I used Partition Magic 8 last night and the program crashed halfwayn through. Now i am getting a blue screen on startup probably because of damaged sectors. I am unable to start xp to run a chkdsk or to install any partition doctor type tools I then decided to re-install my Xp. But during the start stages before installation an error comes up saying there is no hardrive on your computer. please make sure it is switched on or presesnt(or something like that)
View 1 Replies
View Related
Jun 1, 2006
i was attempting to resize my HD using partition magic i did not backup prior During the process my computer lost power. Upon rebooting i receive the following blue screen error message: a problem has been detected and windows has been shut down to prevent damage to our computer if this is the first time you've seen this stop error screen, restart your computer. if this screen appears again, follow these steps:
disable or uninstall any anti-virus, disk defragmentatio or backu utils. check your HD config, and check for any updated drivers run CHKDSK /F to check for HD corruption, and then restart your computer.
View 4 Replies
View Related
Jun 2, 2006
Recently i was attempting to resize my HD using partition magic(i did not backup prior During the process my computer lost power. Upon rebooting i receive the following blue screen error message: a problem has been detected and windows has been shut down to prevent damage to our computer if this is the first time you've seen this stop error screen, restart your computer. if this screen appears again, follow these steps:
disable or uninstall any anti-virus, disk defragmentatio or backu utils. check your HD config, and check for any updated drivers run CHKDSK /F to check for HD corruption, and then restart your computer.
View 4 Replies
View Related
Jul 11, 2009
It started when i use Partition Magic.
there was a notification error said that Partition Magic can't read my Hard Drive, because of 'drive wrong naming' (i forgot the exact word) then came up an option 'do you want to fix it?' YES/NO - I chose YES
but after that, I can't go into to windows again (Vista64) it stuck on loading process forever
- Hard Drive are detected on BIOS
- When I use another 'health' HD with this 'broken' one, then the 'health' HD won't boot either, but it will normally boot again if I unplugged the 'broken' HD
- When booting via Windows Installation Disk (tried to re-install Windows), it stuck again on windows loading
View 1 Replies
View Related
Jan 19, 2009
I have just recently gotten a new computer which came with Vista. Previously what I have done with any new operating system I got was installed it into my old computer. However, I came to find out you can only have one computer assigned to each cd, unless I wanna buy another one, which is unecessary. I wanted to get rid of Vista and return to XP but the XP disc would not install because of multiple errors, such as missing ntldr.
View 14 Replies
View Related
Mar 27, 2010
Bought a new copy of XP with service pac 3 to put on a p4 with a western digital 300 gig hd. I came back to check to see if the formatting was complete and I had the message "a disk read error has occurred press ctl+alt+del to restart".And when I tell it to boot from cdrom xp disk, it starts "setup is imspecting your computer's hardware configuration" and the screen goes blank after a few seconds and it stops doing anything. I'm afraid the mistake I made was deleting the boot sector partition.
View 5 Replies
View Related
Oct 17, 2008
I have several programs on my computer that I don't even know what they do. I'm going through them and deleting what I don't need.
View 2 Replies
View Related
Aug 11, 2007
Browsed these forums and others, tried various solutions, and I can't find anything that's helping me out.I'm running Windows XP Home on a laptop, and when it attempts to boot, it tells me that hal.dll is missing or corrupt.To correct this, I put in my Windows XP CD, and I can get it to the recovery console just fine. At the recovery console, I've tried the following:- chkdsk ("The volume appears to contain one or more unrecoverable problems.")- bootcfg ("There are currently no boot entries available to display.")- fixboot ("The boot sector cannot be fixed.")
- expand from CD ("The specified file was not found."- repair installation (It won't even begin. Error as soon as I select the partition C:)
View 14 Replies
View Related
Feb 5, 2008
I cannot run a anti-virus because I don't know What the owner account password is, and I cannot login to the admin account. Any way of getting past this? (such as doing a install despite the virus or prhaps bypassing the login screen altogether)
View 1 Replies
View Related
Dec 27, 2007
I have a dell PC with windows XP Media Center installed. I think that a virus damaged the boot sector in fact I cannot start my PC.
All I am able to get to is the BIOS or the diagnostics tool, F8 doesn't work, which means I cannot restart in safe mode or last known good configuration and if I use alt+F11, which is the option you have on Dell PC to reformat it in order to have everything the way it was at the time you bought it, it doesn't work.
A friend of mine told me to boot from the CD and then use the fixboot command, the problem is that DELL does not give OS CDs anymore and I honestly do not know what to do
View 6 Replies
View Related
Dec 18, 2005
SATA Drive not recognized as boot drive on XP installation.Need to create an Xp boot sector.I have been working on this for days. Successfully installed once and ended up with corrupted files on the Win98 partition, so want to get it right this time. (Don't remember how I did the "successful" install - after several days of various problems - most of which are now solved - I am a little brain-dead.What I am looking for is a way to create an XP boot on the SATA drive. I assume this means changing the MBR.
System: MotherB: Asus A7V600 with VIA Chipset
Drives: 0 120gb SATA; 1 15GB IDE; 2 10GB IDE
Current Status:Win98 and WinXP both operational but no dual boot. Win98 was installed first. Both systems were a clean install. Both systems installed on FAT32 in seperate partitions on the SATA drive. Computer startup simply goes into Win98, as there is no XP boot sector on the proper drive......
View 4 Replies
View Related
Jun 30, 2006
Where should I install codec like dvix, xvid? In the partition which win xp is on and boot from, or another partition? I would like to install as less programs as possible on win xp partition.
View 7 Replies
View Related
Sep 16, 2005
when i open Partition Magic 8 i see my Maxtor 6Y120P0 drive in a yellow color and the file system marked as "other": but my Windows 2000 Disk Management shows healty:
under windows i can read and write to the partition, so what is wrong? what does Partition Magic wants?
View 1 Replies
View Related
Aug 15, 2005
I seem to have bad luck with multiple partitions on one drive. I have a 160 gb hdd that was partitoned with one approx 137gb partition with windows xp. It was working fine. I decided to partition the remaining space which was something like 25gb. I did it from windows xp in the disk managment snap-in. It worked fine until I formatted the new 25gb partition and assigned the page file to this drive. I had not rebooted before formatting the new drive and I believe the format is what screwed up the drive. I have tried to chkdsk /r but it took forever and then crashed. I believe windows improperly sized the partition over part of the original C partition. I really hate logical drives. I always seem to have some sort of data loss with them..
View 13 Replies
View Related
Mar 25, 2007
I'm receiving a windows -no disk error message that won't stop. I've recently installed System mechanic 7 and network magic
View 1 Replies
View Related
Jul 7, 2010
Now I am having multiple new problems. I want to completely erase the hard drive and install a new version of XP Home, not Pro. At the beginning of the installation process, it gathers system info. Immediately it responds with "no valid system partition" and the only option is to exit from the process. How can I get past this to complete the installation?
View 14 Replies
View Related
Jan 8, 2005
When I boot my Dell Inspiron 3800 laptop I get an error message. The background is black and in white text at the top of the screen it reads, "Memory write/read failure at 10000000 read 00ef02ee expected before 00ef00ef decreasing available memory. Does anyone out there know what this means or how to fix this?
View 1 Replies
View Related
Apr 3, 2010
this has been bothering me for weeks and not a single thing I've tried has solved it. It's really a problem now, because I can't just not back my stuff up forever, I have to get this sorted out.I have a PC that I keep all my stuff on, run uTorrent on, my media center application, etc. It's got 8 HDDs. Half for storage, half for backup. 5TB overall (well less...but you know). I have an application that runs once a day to sync the drives with their counterparts. Everything was fine, until I got a new motherboard and CPU for the system.Now.....whenever I run my backups, this message will appear. Either very rapidly, or at some point during. The whole system will slow to a near halt (it can take 30 seconds for the mouse to register movement), and the only course of action is to turn the system off and on again. It's because of this Delayed Write Failed error (it pops up, sometimes immediately....and sometimes if you let the system keep running).
I've looked online for solutions. Some of them say to disable delayed write in the HDD properties. I've done that for most drives (the drives connected to the system via a PCI-E controller card have that tick box option greyed out. Nothing I've tried has made a blind bit of difference.
View 12 Replies
View Related
