Okay, I just got done doing a fresh install of XP on my master hard drive. The master is small, about 40GB. All my important stuff is on the slave, a 160GB HD. Until tonight, I was using the bigger HD as the primary one, and the master as a small backup drive. I partitioned the larger drive into several bits, five total.
After XP got done installing, I thought I'd merge two of the smaller logical drives on the slave into one, I didn't need them. I used computer management in administrative tools to delete the two uneeded logical drives.That was a big mistake. It merged all the logical drives into one. I need the information on the last two partitions. Need being the word. I downloaded a trial diagnostic tool, and to my joy, it found all the most important data still on the FAT32 partition. However, being a trial tool, I could not retrieve the data, I could only look at it.
I will try keep this to a minimum, as i'm sure this should be easily solved. Basically, new computer, setup windows XP on a 470GB drive, 75GB for the system, with the rest split into two. Due to an internal card reader, XP ended up as the H: Due to a problem when installingsome software, i attempted to change the system drive letter back to C: through the registry. Big mistake. long and the short of it is windows would no longerboot up. At this point, booting to the windows xp setup, the only partition which showed was a 130GB unused partition. Now, all i want to do is make the drive factory fresh. I can make the partitions work within windows (with this dodgy HD as a slave drive) and delete/create partitions etc. However, no matter ho much i format/delete/create partitions, when i load the windows XP setup, it only ever sees the 130GB partition. i tried using the command diskpart> clean to no avail, i thought it would wipe it out, Can anyone advise me how to lose what ever config is stillon that hard drive and have it back abe to be partitioned/formatted etc within the windows setup CD
A while back i installed Linux SUSE on my computer with a grub loader on boot up to choose which OS to start up. I've grown tired of SUSE and i'm running out of space on my hard drive so i'm looking on deleting the partition. Last time i tried it the GRUB loader didn't know what the hell happened so I couldn't boot up at all. So how do i remove the partition in Xp ? (I have forgotten the password to SUSE, thats the main problem)
I want to upgrade to an Intel P4 HT CPU and I want to delete my second XP Pro partition. I have a Silicon Image Raid Controller with a 0 Raid set. How can I delete the 2nd partition with XP Pro without loosing any data from the 1st partition and uprgrade the CPU? I will also upgrade the RAM and the GPU. Is it possible to make a "repair installatÃon"?
I'm currently in the process of selling my laptop. I wanted to nuke the while disk to make sure all my confidential information had gone, using DBAN, but I couldn't get it to create a disk, so instead I'm deleting the partitions on my computer, formatting them, then erasing them using Heidi's Eraser (35 passes).
I had two partitions: a C and D drive. I installed two OS's on the C drive, and I deleted the D partition, and created a new one which became F. i then erased F, so that anything that was on the previous D had been completely cleaned. I then put on a copy of XP on F. So, when I start up my computer, I use the OS which is logged on F. Can i delete the C partition now, which has two OS's on it, whilst I'm using the OS on F? I want to do that, create a new partition, and then erase it 35 passes.
I had 2 partitions on the laptop C and E, last night while fidling about I deleted E and since then laptop does not boot up. Comes up, windows hardware configuration not recoqnized. Tried to recover it but seems recovery bit was also deleted. I have to recover important office work else my life is over!!!
A got a new HP d290 model computer, which came with Free DOS O/S (that is without the Windows XP operating system.It has a Samsung brand 80 GB HD. However on partitioning and formating this HD (using Win 98 / SE,FDISK.Exe file), the total space available is only 78,109,888 bytes (split in to 3 parts). On another computer, made by a different company and with almost similar configuration, I have a Maxtor brand 80 GB HD and on partitioning and formatting, it had 80, 009, 888 bytes available (that is 1.9 GB more)This HD also has 3 partitions.It seems the HP's Samsung HD has a hidden partition. I tried to find it with FDSIK.EXE and also with Partition Magic (version 8.2) and Partition Manager (version 5.5), but was unsuccessful.Is there any other Partition related software, which can show a hidden partition and also be able to delete the same (without damaging the C~ partition)?
I copied my data files to my external Maxtor hard disk before I tried to reformat my internal hard drive and reload Win XP. However during my partition, I didn't realize I still had the external drive (160GB) plugged in and it showed up at the top of the list and the original internal (80GB) below it. So, I followed the instruction mistakenly and went through the process of deleting the partition(on the external hard drive) and tried to partition it into two drives. Then I got an error message as I continue to try to format the hard drive "Your computer's startup program cannot gain access to the disk containing the partition or free free space you choose . Set up cannot install Window XP on this hard disk." I stopped, reboot and tried to go through the delete partition several times with the same error message. After several attempts, I realized that the external hard drive was still plugged in.
So I unplugged the external hard drive and reboot to go through the process of reformatting and partition the internal hard drive into C drive and E drive and loaded Win XP. Now even though I plugged in the hard.After I installed the external hard drive's software,driver and restarted the computer, I connected the external hard drive and don't see the drive in my computer. I could find it under Control Panel/System/Device Manager/Disk drives but it doesn't show up as an external hard drive under "My computer" with a drive letter. Under the disk management, I see the drive as Disk1 but it was unallocated. Did I lose all my data due to the delete of partition? Can I recover my data and drive ?
I was reformating my pc and when i clicked to delete a partition it said it was unable to delete it thus not being able to continue reformatting. I tried almost everything (making a boot disk,...) and i dont knoe whats wrong. I've been able to reformat before but i dont know why. My system is NTFS I'd
pagefile.sys is corrupted since it is fixed a 2GB whatever setting (no page file, system managed...). I choose in the virtual memory panel. I can't changed its size and would like to delete it so windows xp (sp2) can recreate a new correct one. the purge at shutdown does not work too and I don't know the password for the recovery console under the DOS. I am looking for a simple solution to delete this file which is on an ntfs partition.
How do I make the second partition, which includes all files from another hard drive, pretend that it is the main partition? I want to simulate the second partition being my main one for a while.
I have my Windows format disc and I want to create another partition with it. I tried to create one, but it said something like "You have no more space to create another partition because you used up all your space on your Windows primary partition". See, when I reformatted my computer a while back I just created 1 partition for Windows and applied all the space onto that partition.
If there is a way I could remove some space off of my Windows primary partition and create another partition with the space I removed. I want to do this so I can put general things in my other partition such as documents, music, etc. and just leave the other partition for Windows and programs.
What are the steps needed to access one of my partitions, delete it, then use 1/2 the space and apply to system drive and the other 1/2 to another partition?
I bought a new computer.It appears to have been partitioned into a NTFS format and FAT32 format.The default drive for my documents & my pictures etc is the NTFS which I have been using happily. It is Media Centre Edition so I also have a few large files (>4GB) - though I dont keep them long term.NTFS partition has fulled up - but I cant move my large files to other partition to free up space
I've done a little bit of reading but my question is "Should I reformat the FAT32 to make it more of use to me?".I cant really see the need arising to access older OS files, except .JPG's (photo's I had on my old Windows ME Comp) or "Should I move all my smaller files (documents and photo's) to the FAT32 partition and use the NTFS drive for the bigger files?"
My hard disk arrangement is C(primary partition FAT32)for Windows XP D(extended logical FAT32) for non-os data (movies, pictures etc..) F(primary NTFS) for Vista.. I am formatting F: and then C: through XP installation CD (and C->NTFS from FAT32) is this ok??? will D: be accessible after installing XP on C???
I would like to know if it´s possible to take free space from an extended partition and redistribute it to a primary partition using partition magic 8.0..both partitions are NTFS
Now I am having multiple new problems. I want to completely erase the hard drive and install a new version of XP Home, not Pro. At the beginning of the installation process, it gathers system info. Immediately it responds with "no valid system partition" and the only option is to exit from the process. How can I get past this to complete the installation?
My existing C: drive. First I was getting the "Error 983" error. Then I un-installed SP2 which was causing a gang of problems, freezing programs for a couple mins mostly. After I got it uninstalled I did a disk defrag, then a chkdsk /f. Now I have partitioned the drive using PM8 again and this time after the reboot it is telling me it is completed but once Windows XP reboots there is no new partition.
Im trying to install Suse Linux 9.0. But I really want to have 2 new partitions, one for Suse, and the other as a back up.
I had perfectly working PC with XP Pro installed on a 160Gb Maxtor HDD.For no reason I error checked the hard drive, which the system did after rebooting, at the end of the test the system rebooted and announced that there was a error on the boot and boot.ini.Useing XP Emergency (on disk) I tried fixmbr which did nothing then I tried Fixboot. XP found the drive identified it as FAT and said that it was successfully fixed.The drive was FAT and is now unusable.Partition Magic sees it as a FAT drive as does XP when I switched the HDD into another machine.
i plan to format my computer again and this time i plan to split my primary partition before i format. When i go to format i want to format only the active partition with windows in it.I have two questions. This trick does work right? the partition i created in windows using magic partition 8 won't be formated along with the active partition right? I plan to backup everything on my second partition.When i created the second partition i had two options. to either make it a logical partition or a primary partition. I chose primary partition. would that work?i plan to install windows xp pro sp2.
Over a year ago when I setup my new system and before installing most of my APPS, I backed it up to a small HD. My Win Xp Pro MCE 2004 has become a little buggy (MY FAULT).How would I copy or clone the smaller HD over to my 80GB drive AND maintain the larger partitions? I have Ghost 2003 but I'm not sure if it permits me to set the partition size when copying HD's.
I reinstalled my OS several months ago, and decided that I might want a dual boot in the future. I already had an old, smaller drive in the machine that's labeled the c: drive. Reading one time that for security purposes it's good to have your OS on a drive other than C:, I decided to not alter the drive lettering.
I then partitioned a new internal hard drive into several logical drives. I formatted the D: partition as a Dos fat32 partition and the rest as NFTS partitions. Somehow, I allowed the D: partition to be the primary partition, while the E: partition which contains the Win 2000 Pro OS Winnt directory is a logical drive.
When I just checked disk management, I noticed that not only is boot.ini on the D: Dos partition, but so is ntldr along with the following Dos setup files:
To reformat my computer now and i downloaded all the files i'd need to reformat and compressed them into a single rar file to put onto my d drive.
Although when i go to move theses filesonto my d drive i get a message saying: cannot copy "reformatfiles": There is not enough free disk space Delete one or more files to free disk space, and then try again Free space on this drive by deleteting old or unnecessary diles click disk cleanup.
I've just resized a partition on my main physical drive, and the OS sees the adjacent partition as unfromatted.
I'm using Partition magic pro 7 and WinXp pro.
The partition I resized is the primary OS partition which is formatted as NTFS, the adjacent partition is FAT32. How can I get XP to recognise the FAT32 partition again?
I decided to try Linux. 'Ubuntu' was my type selection. After trying by running off a CD I then decided that I would pick up some partitioning software like 'Partition Magic' or some software along that line to do the partition. But somewhere(s) I read that virtual or software partitions are less then a good idea for reasons I don't recall at the moment.
Is it possible to recover data from an external HD that I accidently deleted the partition and created a new one I just got a "new" computer - it's actualy a hand-me-down that I was trying to do a clean install of Windows XP on. I booted it up with the XP disk in the CD drive, and thought I was telling it to delete the existing partition and create a new one on the C: drive, but I didn't realize that it was also recognizing the external drive, which was already plugged into a USB port (why I even went ahead and plugged it in I don't know - that was stupid mistake It was the first one listed, and I thought it was telling me that there were two partitions on the internal drive, not two drives I also didn't pay attention to the size it was telling me the drive was (stupid mistake #2), I just told it to create a partition with the maximum possible size
I have a very large, corrupt disc image on my hard drive that I want to delete, but every time I try to delete it Windows displays the message "Cannot delete 'filename': it is being used by another person or program. Close any programs that might be using the file and try again." The disc image is not mounted with any program, and hasn't been for some time. I tried aborting random processes that I thought might have something to do with the file, as well as restarting. No matter what I do, there seems to be something using the file. Are there any tricks to getting around this so I can delete it? Can I check, somehow, to see what program is using it?
