Network / Sharing :: Scan For Available WiFi Connections?
Jul 5, 2013
When I turn on my Toshiba Satellite laptop, it does not see my i-phone hotspot. Wi-Fi status says "No Wi-Fi connections available". I always have to turn the hotspot off and then back on after the laptop is up and running for the laptop to find it. This does not happen with my desktop. It sees the i-phone hotspot without the need to cycle the hotspot off and back on, so I'm thinking that it has to do with the Toshiba rather than the i-phone. Both laptop and desktop are running Windows 8. Not a big problem, but I thought some one may know of a setting which I need to change.
I have my ethernet cable connected right now, but I can't even load my wifi connections at all. I live in apartments so everyone around me has wifi and my phone and iPad is clearly connected, but it won't load any connections.
This problem occurs unexpectedly. I usually use my laptop to connect to WIFI in our school then suddenly i cannot detect any wifi connection even bluetooth disappear.
My fully updated Windows 8.1 notebook suddenly will not show any wifi connections when I click on the icon in the system tray (it shows "No Connections are Available", although it is connected, and I can surf and browse normally).
To connect to a new network, I have to manually enter the details of the network, and then it connects. This is something new, since previously it would show all the available networks, and allow me to make a selection (which is normal). What setting could have flipped do enable the above situation?
My 8.1 laptop shows multiple network connections to my Samsung Smart TV --- One as "media connections" and 3 as "other connections". Both devices are on a simple wireless network using Linksys WRT54GS.
Under the "Network" page, most of the "Properties" of the TV connections are the same except for "Serial Number" and "Unique Identifier". Did I do something wrong when setting things up? Are these extra connections harmful? Should I delete some? How?
My computer has 2 wireless cards and a gigabit ethernet port. I have my own internet and my neighbors each allow me to connect to their internet. If I were to set the Wi-Fi to connect to theirs, and the ethernet to connect to my internet would I be able to take advantage of the extra bandwidth?
I am having a problem with bridging my connection I have been online look around and I could not seem to find anything that has worked ok basically I have 2 connections I want to bridge together but after is done bridging no bridge appears under network adapter settings ?
So I just got a custom built computer with Windows 8.1 installed on it, When I go to settings > Networks, It says No Connections are Available, every other device in the house has connection to our WiFi.
On my Toshiba laptop (I've only had it since the 8th of August) under Networks it says, "No connections are available". I was playing Diablo3 and then it suddenly said not connected to battletnet. That is besides the point, but I think I might have hit something that turned the wifi off. After failing to fix it with a system restore it blue screened saying something about an error and collecting a data and that it was going to restart itself. Then it said to get more information or something like that the error code was MEMORY_MANAGEMENT. After restarting I thought it was still messed up (it showed no networks available in the lock screen) then I logged on and it still did. Then it showed I was connected to WiFi again, then after leaving for a few brief minutes it was back to no connections available. It did the blue screen thing again and restarted.
I'm trying to create a shortcut to "Control PanelNetwork and InternetNetwork Connections". I am not able to. Is there something about going to this folder that is forbidden?" If I have inserted the incorrect path please give me the correct answer.
I am preparing a lesson and a short cut to the adapters will make it easier.
So I've set up my desktop PC to function as a portable WiFi hotspot for my other mobile devices. First I used the Cmd Prompt to create a sharing network, but since I had to open that every time I started up the computer, I switched to using a program called MyPublicWiFi (1 click setup).
However, in the last few days, my WiFi connection was getting kind of buggy. (No internet connection with my phone while I was connected to the WiFi network, etc)
Just now, I looked at the Network Connections, and there are 3 LAN connections that weren't there before. (picture: [URL] ....) Are they part of the problem, and how do I remove those networks?
I'm trying to set up VPN to connect immediately upon startup.
I decided to try setting up my VPN in Windows itself, instead of using Open VPN as before.
This is the Windows VPN functionality that's available from the Metro themed interface and . But it's so dumbed-down that I can't even see what type of VPN connection this actually is.
If this connection if PPTP or L2TP? Or something else?
Whichever it is, is that connection considered to have integrity or is it more or less cracked?
Live Tiles missing. I recently refreshed my comp. as i had issues with my live tiles as you can see in the link above. And now none of my tiles connect to the internet. I checked my connections, which is fine.
I keep getting a constant error msg saying that the tiles cannot be displayed as there are no internet connections available.
I user FTP & Telnet a lot to connect to devices on our LAN.
With Windows 8 I've been using ZoneAlarm as my firewall as I found Windows Firewall caused a 5 -10 second delay in every FTP / Telnet Connection.
Last night I upgraded to Windows 8.1 and ZoneAlarm no longer works, so I'm back with the Windows Firewall and the delay in connections.
I've ensured the APPS I use have access via the firewall and they do connect and work fine... but after establishing the connection there is a 5 - 10 second delay in the connection. With ZA this was all instant..
I have a new Dell laptop with Windows 8.1 - I work from home & connect to the internet via my home wifi network. The problem I have been experiencing is that my laptop connects to the internet at boot up but then disconnects for several minutes & then re-connects again. This coincides with the Network & Sharing Centre showing a number of Local Area Connections (numbered 3,4,5,6 etc) being created under Unidentified Public Networks. I have tried disabling the LAC's but they re-enable whenever I re-boot & I have the same issues again. My networking knowledge is very limited so how to rectify this issue.
The computer turn off the wireless connections and defaults into airplane mode. I had this problem with Windows 8. The option to easily toggle airplane mode on and off become grayed out unchangeable. The only way I found to temporarily fix the problem was to rightclick the airplane icon and then troubleshoot the wireless connections which would then turn wireless back on. I had the option to upgrade to 8.1 and I did and it fixed the problem for a while. It did happen again which is why I'm back on the web searching for possible more permanent solution for this. Luckily it only happened once a week ago and hasn't happened again. I was wondering if this bug was known about and if you possibly know of a way to fix.
On all of our Windows 8.1 clients, every time a user tries to add a printer using the 'add a printer' wizard, it triggers alerts from our secure network devices indicating that someone's trying to log in to them with SNMP.
We need the failed logon notifications but it's incredibly annoying to get these all the time.
Any way to disable the SNMP scan when adding printers? Windows 7 didn't do this. Nor did windows 8 base as I recall.
I've once again encountered this problem with my Canon PIXMA MP620 printer/scanner: when using it wirelessly, it can't print. According to 'Devices And Printers', it's offline and therefore most programs I use in Windows 8.1 claim it can't print.
However, using Canon's program 'MP Navigator', it can scan from the printer without any problems. I can scan from the computer to the printer and the other way around. Therefore I'm suspecting that the problems lies with Windows 8.1 and not the printer. The connection is obviously there but Windows doesn't seem to think so.
I can't find a solution in the printer's manual, Windows doesn't give me anything when I try to troubleshoot the printer in question, and Canon's own 'Network IJ Tool' can find the printer but says it's doesn't work without clarifying why.
I am using the N600 Wireless Dual Band Gigabit ADSL2+ Modem Router DGND3700v2 This has 2 channels 2.5ghz and 5ghz .
On my main desktop windows 8 has sucessfully found and connected wirelessly to the 2.5ghz connection. However, when I want to do video streaming the 5ghz connection would be better.
On my other devices I can search / scan for all available connections and I can see both the 2.5 and the 5 connections. For example, my laptop running windows 7 can see both connection and I can choose which one i want to connect too.
However, Windows 8 seems to have locked into the 2.5ghz connection and cannot see the 5ghz connection . Is there a way to force Windows 8 to scan again so it can see the 5ghz connection ?
Is there a way to setup network profiles or something so that when I bring my Surface Pro to work and connect to the wireless network there it will use the static ip address I have but when I disconnect and then connect to my home wifi it will go back to DHCP? On my MacBook Pro I can go into the network settings and change the location profile I have setup for networks but I don't see anything like this for Windows 8.
I just bought a Lenovo Y500 a couple of days ago and it came with a pre-installed Windows 8 everything seems working fine but when it comes to Wifi it randomly disconnects a lot , sometimes shows limited access and most of the time the signal strength bars keep going up and down.
I purchased a new Windows 8, Inspiron 15 7000 series - 7537 last December. I had been using a router at a hotel for the time, and it worked correctly. When I arrived home, I had a Belkin router, and i experienced network issues in that i could not connect to the wifi. I could connect with Ethernet cable. The problem was fixed through customer support eventually, but I now have a new Comcast router, and i'm experiencing what appears to be the same or a similar issue. I can access the internet fine by wire. With wifi, it says i have access to the internet over the internet icon in the bottom right, but i cannot access webpages. I can use skype, and communicate through it.
Here is the result from the ipconfig /all :
Microsoft Windows [Version 6.2.9200] (c) 2012 Microsoft Corporation. All rights reserved.
C:Windowssystem32>ipconfig /all Windows IP Configuration
[Code] .....
I really need the wifi on this router working for this laptop. Let me note that it works on other laptops, so it should be an issue with hardware or settings on this laptop.
I have two wifi APs in the home and only one has an Internet connection. the other is to access the wired LAN.
Last week I updated from Windows 8 to Windows 8.1 and thought everything was going well until I started getting wired LAN dropouts.
I have traced it back to 8.1 handling connection to wifi APs. In Windows 8, I was able to have "Connect automatically" for BOTH wifi adapters on this laptop. Now when I try to connect to the non-Internet AP, Windows 8.1 announces (correctly) "Limited access" and that's what Windows 8 did too. BUT, Windows 8.1 waits a few seconds then drops the connection with a useless message, "how me solve connection problems," where there is NO problem. A limited connection for the AP to the wired LAN is OK as it was in 8.
So now I am stuck with no home LAN access unless I drop the Internet AP and connect to the LAN AP.
Also, in the great wisdom of 8.1, because it is only a "limited" connection, it does not remember the Passphrase so I have to type it in every time. So much for progress.
What to do to get past this behavior and have a "limited" connection as OK as it is with Windows 8?
I prefer to keep my home WiFi network from public view by disabling the SSID broadcast, i.e "hiding" the network.
With two modem/routers (a Belkin Play Max F7D4401 ADSL modem/router and now a Cisco EPC2325 DOCSIS modem/router) on two computers (home-built desktop and Acer TM8172T notebook), after the initial connection Windows 8 Pro would not reconnect without tediously re-entering the SSID name and password. Once it does connect, it displays the original SSID name with a new one with an incrementally increasing appended number like:
I was manually deleting them all (except the original) using netsh, until I realized you can <right-click> on an entry in the screen above and choose "Forget this network."
This is the process I go through each time to re-connect. Is there something I'm missing?
I read that if Windows 8 saves too many WiFi connections, it cannot "remember" them to automatically reconnect to them, so on the notebook, I deleted all but wpcTrue (the original), and it now automatically reconnects, although occasionally it will add a new connection with an incrementally increased number -- currently the notebook shows both wpcTrue and wpcTrue 2. I had used the notebook on the road, so had about five WiFi connections saved. On the Desktop my home network is the only WiFi connection I've ever made. However, no matter what I do on the desktop, it NEVER remembers to automatically log on when the SSID is not broadcast.
I even tried manually setting up a connection via Network and Sharing Center > Set up a new connection or network, to no avail -- the desktop computer will not automatically reconnect.
I doubt that this is relevant, but the Belkin modem/router, the Belkin USB adapter I use on my desktop computer, and the notebook's Broadcom internal modem are all b/g/n. The Cisco modem/router is b/g.
If I "unhide" the SSID, i.e. broadcast the SSID, all is well in the world. Both computers automatically reconnect to the modem/router. If I hide the SSID, and then disconnect or reboot, the desktop computer will not automatically reconnect.
I just noticed that the pop up WiFi connection column shows "WiFi-2 Off" -- what does the "Off" mean?
And, why is it "-2" ? My notebook just shows "WiFi', period. (The first image with "WiFi (Off)" was from a previous Windows 8 installation on the desktop computer. I decided to change from EFI-boot to non-EFI so reinstalled Windows 8. I simply used the old image as a quick way to show how the connection name assignment runs away.)
How can i create local WIFI network without having internet access on my pc. This seems to work if I have access to internet but when i disconnect internet connection my PC ( virtual router ) cannot see anymore other devices..
All other devices that are connecting to my virtual hostednetwork are working without any problems expect my pc. What have i missed that my PC where virtual hostednetwork is running cannot see devices in "virtual" network without internet access?
My ISP provides service only via 802.11. I use laptop A most of the time. The captive portal for the service provider only allows one login per account at a time. The policy is intended to prevent multiple people sharing one account. It's just me, I'm the only user, but very occasionally I'd like to have a 2nd laptop access the internet simultaneously. No abuse, just the simple convenience of not having to logout from A if I need to use B for 30 seconds.
What I want to set up seems simple and it probably is:
WiFi Internet <---> Laptop A <---> ethernet cable <---> Laptop B
Such that Laptop B can share A's active WiFi connection without having to request its own unique address from the ISP.
At present, Laptop A has its network interfaces set up so: - WiFi is connected, active, functional. Selected the "Yes turn on sharing and connect to devices" in sidebar. - Under the wired network properties IP Version 4, I manually set addresses to be IP 192.168.10.1 Subnet 255.255.255.0 Gateway 0.0.0.0
Laptop B has only a wired network, set to IP 192.168.10.2 Subnet 255.255.255.0 Gateway 192.168.10.1
A & B can connect directly to each other, share folders, etc.
What do I need to do in order to get laptop B to transparently use A's WiFi connection? My guess is that A needs to be set up to do some routing between the internet side and the 192.168.10 subnet, and B needs to be set up to look to A as its "ISP" ... but I don't know where to begin.
I want to forget a Wi-Fi network from my network list i windows 8.1 . But when I right click on that network (to forget that network) nothing happens i.e. right click menu does not open.
My laptop is few months old HP Pavilion g6 OS: Windows 8 uses a ralink rt5390r 802.11bgn wifi adapter.
The wifi was working just fine suddenly it stopped. It detects my home network but every time it tries to connect ends up "unable to connect to this network". It connects to my friends wifi but not mine. And it connects with cable.
There is a red cross on the wifi network but it's green not GREY. It is not a modem problem because the other PC connects just fine. When I'm on wifi, cmd ipconfig gives me disconnected media for all the network cards on the laptop. Command netsh shows failure and access denied.
What I have tried to do for the past week :
I upgraded the adapter/ driver. My windows is fully updated. I re-installed the network card. I tried a USB wifi. I uninstalled the private server. I uninstalled my Norton because I thought it was blocking the connection I also deactivated the windows fire wall. I changed the SSID and PSW ... nothing worked. and of course I tried restarting, resetting, rebooting, deactivating and activating, disabling and enabling every single thing but nothing works.
I'm having a serious problem trying to connect my other laptops running windows 8, the host laptop that is connected to internet with modem is Compaq Presario g56 laptop also running windows 8, I'm connected to the internet with my evdo modem and this laptop is browsing fine, I download mhotspot to share this connection, this other computers are connected but showing limited connection in their network and sharing panel, the modem have access to internet and the private network I created on the host computer also show access to internet, so why are other computers connected to this computer are not browsing with this internet connection. attached is the screen shot of the host computer this problem had been persistent for more than one week
I just bought a msi s30 laptop yesterday. So everything went fine when I test the wifi connection before I go to sleep. When I say fine, I mean I could connect to the internet. Then when I woke up this morning, I turn on the wifi but it says "no network found". I check the router and it is working perfectly fine. I also checked the device driver and its also working properly.
