I want to forget a Wi-Fi network from my network list i windows 8.1 . But when I right click on that network (to forget that network) nothing happens i.e. right click menu does not open.
View 6 RepliesRecently I have upgraded my Lenovo G580 laptop from windows 8 to windows 8.1. After up-gradation Wifi is stop working. I have checked the WIFI device driver(Broadcom 802.11n) in device manger and it is showing working fine but in the Networks section the Wifi is showing disabled.
I am attaching the screen shot of the device driver property and the my network panel.
Is there a way to setup network profiles or something so that when I bring my Surface Pro to work and connect to the wireless network there it will use the static ip address I have but when I disconnect and then connect to my home wifi it will go back to DHCP? On my MacBook Pro I can go into the network settings and change the location profile I have setup for networks but I don't see anything like this for Windows 8.
View 4 Replies View RelatedI am facing a strange problem with my internet connection on Windows 8.
I have a netgear WNR612 wifi router and two laptops connected to it running Windows 7 on first and Windows 8 on second.
The connection in Windows 8 laptop shows sufficient signal strength but when I try to access internet, it does only shows connecting. I have changed browsers, wifi router, adsl router, released and reconnected IP address, forgot and re-added wifi network, reset wifi router to factory almost everything.
The strange part is that as soon as the other Windows 7 laptop is disconnected from the network, Windows 8 internet start working fine. I have tested this many times and there is no doubt in this behavior.
I dont know whether the problem is in any update installed on Windows 8 the older Dell Wireless 1703 wifi card or some virus in the other Windows 7 laptop.
My ipconfig output:
Ethernet adapter Bluetooth Network Connection:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Bluetooth Device (Personal Area Network)
Physical Address. . . . . . . . . : F4-B7-E2-59-1E-42
[Code] .....
Note that I have assigned preferred IP addresses to both laptops based on MAC.
I use a small usb modem for my internet access and using a usb wifi adaptor and a virtual wifi router I was able to share my internet around home quite affordably.
Every now and again the software 'virtualrouter' would cause a crash. Maybe once every 3 months.
When I updated to 8.1 the software no longer worked, nor did any other. What's more it cause a DPC-Watchdog violation within a few minutes.
When I say the software doesn't run, one of two things happen. My old program 'virtualrouter' runs as normal, but none of my devices can connect. The network is available, but connection is impossible.
With other programs I get told that the wifi adaptor is not enabled. Which it is.
Something has changed in the upgrade and I don't know what. Every option and test I've run and enabling of virtualisation says that it should work. But then the BSOD arrives.
I seem to be going round in circles trying to reconnect a working Windows 8 laptop to the WiFi after upgrading to 8.1
It refused to recognise the existing and working WiFi upon reboot after upgrade.
I have twice ran the 'netsh wlan delete profile name=[profile name]' command to remove the profile, rebooted the machine, re-added the profile, nothing happens.
The network symbol in the system tray when clicked doesn't show the profile I created, so I can't select it to connect to (though I set it to auto connect?), it just shows 'Hidden Network' , but when clicking this and I enter the SSID and WPA2 key, it just errors with a failed to connect message.
This was working fine, that's how I downloaded the update, now it's broken!
I just bought a Lenovo Y500 a couple of days ago and it came with a pre-installed Windows 8 everything seems working fine but when it comes to Wifi it randomly disconnects a lot , sometimes shows limited access and most of the time the signal strength bars keep going up and down.
View 6 Replies View RelatedI purchased a new Windows 8, Inspiron 15 7000 series - 7537 last December. I had been using a router at a hotel for the time, and it worked correctly. When I arrived home, I had a Belkin router, and i experienced network issues in that i could not connect to the wifi. I could connect with Ethernet cable. The problem was fixed through customer support eventually, but I now have a new Comcast router, and i'm experiencing what appears to be the same or a similar issue. I can access the internet fine by wire. With wifi, it says i have access to the internet over the internet icon in the bottom right, but i cannot access webpages. I can use skype, and communicate through it.
Here is the result from the ipconfig /all :
Microsoft Windows [Version 6.2.9200]
(c) 2012 Microsoft Corporation. All rights reserved.
C:Windowssystem32>ipconfig /all
Windows IP Configuration
[Code] .....
I really need the wifi on this router working for this laptop. Let me note that it works on other laptops, so it should be an issue with hardware or settings on this laptop.
I have two wifi APs in the home and only one has an Internet connection. the other is to access the wired LAN.
Last week I updated from Windows 8 to Windows 8.1 and thought everything was going well until I started getting wired LAN dropouts.
I have traced it back to 8.1 handling connection to wifi APs. In Windows 8, I was able to have "Connect automatically" for BOTH wifi adapters on this laptop. Now when I try to connect to the non-Internet AP, Windows 8.1 announces (correctly) "Limited access" and that's what Windows 8 did too. BUT, Windows 8.1 waits a few seconds then drops the connection with a useless message, "how me solve connection problems," where there is NO problem. A limited connection for the AP to the wired LAN is OK as it was in 8.
So now I am stuck with no home LAN access unless I drop the Internet AP and connect to the LAN AP.
Also, in the great wisdom of 8.1, because it is only a "limited" connection, it does not remember the Passphrase so I have to type it in every time. So much for progress.
What to do to get past this behavior and have a "limited" connection as OK as it is with Windows 8?
I prefer to keep my home WiFi network from public view by disabling the SSID broadcast, i.e "hiding" the network.
With two modem/routers (a Belkin Play Max F7D4401 ADSL modem/router and now a Cisco EPC2325 DOCSIS modem/router) on two computers (home-built desktop and Acer TM8172T notebook), after the initial connection Windows 8 Pro would not reconnect without tediously re-entering the SSID name and password. Once it does connect, it displays the original SSID name with a new one with an incrementally increasing appended number like:
I was manually deleting them all (except the original) using netsh, until I realized you can <right-click> on an entry in the screen above and choose "Forget this network."
This is the process I go through each time to re-connect. Is there something I'm missing?
I read that if Windows 8 saves too many WiFi connections, it cannot "remember" them to automatically reconnect to them, so on the notebook, I deleted all but wpcTrue (the original), and it now automatically reconnects, although occasionally it will add a new connection with an incrementally increased number -- currently the notebook shows both wpcTrue and wpcTrue 2. I had used the notebook on the road, so had about five WiFi connections saved. On the Desktop my home network is the only WiFi connection I've ever made. However, no matter what I do on the desktop, it NEVER remembers to automatically log on when the SSID is not broadcast.
I even tried manually setting up a connection via Network and Sharing Center > Set up a new connection or network, to no avail -- the desktop computer will not automatically reconnect.
I doubt that this is relevant, but the Belkin modem/router, the Belkin USB adapter I use on my desktop computer, and the notebook's Broadcom internal modem are all b/g/n. The Cisco modem/router is b/g.
If I "unhide" the SSID, i.e. broadcast the SSID, all is well in the world. Both computers automatically reconnect to the modem/router. If I hide the SSID, and then disconnect or reboot, the desktop computer will not automatically reconnect.
I just noticed that the pop up WiFi connection column shows "WiFi-2 Off" -- what does the "Off" mean?
And, why is it "-2" ? My notebook just shows "WiFi', period. (The first image with "WiFi (Off)" was from a previous Windows 8 installation on the desktop computer. I decided to change from EFI-boot to non-EFI so reinstalled Windows 8. I simply used the old image as a quick way to show how the connection name assignment runs away.)
How can i create local WIFI network without having internet access on my pc. This seems to work if I have access to internet but when i disconnect internet connection my PC ( virtual router ) cannot see anymore other devices..
All other devices that are connecting to my virtual hostednetwork are working without any problems expect my pc. What have i missed that my PC where virtual hostednetwork is running cannot see devices in "virtual" network without internet access?
My laptop is few months old HP Pavilion g6 OS: Windows 8 uses a ralink rt5390r 802.11bgn wifi adapter.
The wifi was working just fine suddenly it stopped. It detects my home network but every time it tries to connect ends up "unable to connect to this network". It connects to my friends wifi but not mine. And it connects with cable.
There is a red cross on the wifi network but it's green not GREY. It is not a modem problem because the other PC connects just fine. When I'm on wifi, cmd ipconfig gives me disconnected media for all the network cards on the laptop. Command netsh shows failure and access denied.
What I have tried to do for the past week :
I upgraded the adapter/ driver. My windows is fully updated. I re-installed the network card. I tried a USB wifi. I uninstalled the private server. I uninstalled my Norton because I thought it was blocking the connection I also deactivated the windows fire wall. I changed the SSID and PSW ... nothing worked. and of course I tried restarting, resetting, rebooting, deactivating and activating, disabling and enabling every single thing but nothing works.
I just bought a msi s30 laptop yesterday. So everything went fine when I test the wifi connection before I go to sleep. When I say fine, I mean I could connect to the internet. Then when I woke up this morning, I turn on the wifi but it says "no network found". I check the router and it is working perfectly fine. I also checked the device driver and its also working properly.
View 5 Replies View RelatedThe small icon that sits in the system tray, bottom right, near clock,won't work, it should show 5 or 6 bars of signal strength, but does not....I am connected via a 3 ''dongle'' and everything is fine..
View 2 Replies View RelatedToday I was working for a couple of hours without any problems on my Windows 8.1 Pro 64-bit, processing many files and saving them over my network folders.
Suddenly, at one point, when I was about to save a file over a network folder, the system asked me whether I want to turn file sharing and network discovery on.
I believe I had set it up many weeks ago right after system installation and haven't touched it since then. I've also noticed that my LAN network status was somehow changed to "Public" (the same happened to my Kaspersky Internet Security firewall settings related to networks, but as far as I know it reads those information from the system settings).
I know it is possible to manually change network type and turn on/off files sharing and network discovery but I haven't do so for sure. I don't thing there's a hotkey combination that does so and I could select it accidentally. Thus, I believe the system might have changed / reseted it by itself, but... it's simply odd.
I'm having a serious problem trying to connect my other laptops running windows 8, the host laptop that is connected to internet with modem is Compaq Presario g56 laptop also running windows 8, I'm connected to the internet with my evdo modem and this laptop is browsing fine, I download mhotspot to share this connection, this other computers are connected but showing limited connection in their network and sharing panel, the modem have access to internet and the private network I created on the host computer also show access to internet, so why are other computers connected to this computer are not browsing with this internet connection. attached is the screen shot of the host computer this problem had been persistent for more than one week
View 2 Replies View RelatedI am trying to setup a wifi hotspot in my Windows 8.1
I have been trying to do this manually in the Command Prompt as all the proprietry systems 4 No) I tried all failed after about 12 hrs
I used the following command "netsh wlan start hostednetwork mode=allow ssid=NAME=password"
And obtained the correct response
I then typed "netsh wlan start hostednetwork" and got the following response
" The hosted network could not be started
The group or resource is not in the correct state to perform the requested operation"
How can I determine what this means and how is it resolved
I did check using the command prompt that this was possible with the computer and received acknowledgement
just got a alienware 17 laptop and i installed windows 8 on it.
now when i go to connect to the internet through wifi like i normally do it cant find any wifi signals and says i have no network adapter driver? i tried using a Ethernet cable at work with different internet and when i plug the Ethernet cord in it doesnt do anything and still says no connections at all
btw ive tried updating it through the files on my computer and it says its up to date, used troubleshooter everything. nothing worked sadly
My girlfriend recently updated her computer from Windows 8 to 8.1 Since then, she's been unable to connect to her home wi-fi. She can only connect via cable. Unfortunately, neither of us have disks to roll her back to Windows 8.Yesterday she brought her computer to my house and it connected to my wi-fi with no problem.
I updated her adapter drivers to Windows 8.1 but that had no effect on her ability to connect to her home wi-fi network.Last night she ran "troubleshoot problems" and it says that her adapter is damaged. I highly doubt that since the computer is only a couple of months old and she could connect to my wi-fi network.
Computer: Lenovo G405
Modem/Router: ZTE ZXHN F660
Wi-Fi Adapter: Broadcom BCM4313 802.11b/g LP-PHY
Recently upgraded my laptop to Windows 8.1 and I cannot see any 5Ghz wireless networks, even though they are present (I am able to successfully see and connect using other devices including a Windows 7 laptop). I can see 2.4 Ghz networks and connect no problem. I have upgraded the wifi driver to the latest Windows 8.1 version for the Intel Wireless-N 7260 card, v16.6.0.8 but no luck.
View 9 Replies View RelatedFor some reason my windows 8 Hp will not connect to my home wifi network. Has had no problem connecting in the past but yesterday I unplugged my router to move it to another part of my house and ever since then it can't connect. My cell phone and other laptop connect to the internet no problem.
On my Hp it will show a list of wifi networks and my home network is on the list, however, when I try to connect to it and then troubleshoot the problem it says I can't connect to the network because it is hidden. I don't see how thats possible since the network name shows up on the list of nearby wifi networks.
What I've done but hasn't worked:
Reset my router and laptop multiple times.
Tried to manually connect to network.
Forgot the network on my laptop and tried to reconnect.
I don't understand how one day it can connect to the wifi fine and then I unplug it and all of a sudden it can't connect but my other devices can.
Windows 8.1, Broadcom 802.11n network card&driver,
My computer stopped recognizing the wireless networks at my university - oddly enough, some other networks elsewhere can be found (although I cannot test if I can actually connect to them, since they are passworded/not mine).
I followed the 3 steps of Network Posting Tips
Xirrus Wi-Fi Inspector showed nothing: Connection - Broadcom 802.11n network card - NA, everything under Wireless and Addresses also NA. No networks.
My home adsl modem works.
I have Windows 8.1 installed on my laptop and following is the screen shot of the network information:
1. Basic Network information and setup information.
2. Properties of TIC/IP 4 connection under Advanced/WIN tab
Although, I can connect to other laptop if both are wired, but if other laptop is not wired then I can only see its name appearing in the homegroup connection but cannot connect to it.
I am running Windows 8 Home Edition. On a HP DV6-7250CA.I have a Intel Centrino Wireless-N 2230 Card.I also have several other laptops and desktop all connected to the same router. For some reason, randomly my Windows 8 HP laptop turns of my wifi internet access just on this laptop, then when i try to reconnect, it says unable to connect. The only way I can get back on line, is if I go to device manager, and disable and then reenable my wireless card.I have tried reinstalling the driver, and it still happens. None of my other machines are effected and run great on wifi. Why just this windows 8 laptop is randomly doing this?
View 9 Replies View RelatedI have the same problem, I used to connect to my collage wifi, which is powered by sonicwall for the past 1 year, but I can't able to connect it anymore from my room.... I use TP link wifi routerTL-WN7200ND...my signals are good in my room buy it not connecting, saying unidentified network... I tried formatting c dive and re installed OS and all, I tried even windows 7, but my problem is not solved, I tried ipconfig cmd command and many, but none of them worked for me.... I forgot tell something, I can connect to the proxy from a 10 rooms after my room,with the same signal strength... but not from my room....
View 5 Replies View RelatedI'm in Window 8 on a Toshiba L855-S5112 Satellite laptop. It's an inexpensive laptop, which was most likely my first mistake.
But... My wireless sees nothing, and when I check the device manager for the network adapter info, it's enabled and it reports that it's working fine. the wifi switch is definitely set to on. With "show hidden devices" turned on, this is what I see for network adaptors:
Im looking for a way to have wifi access per user for example one user can have access to wifi while another user cant have access. (Currently Using Windows 8)
In Windows 7 I used this method (Profile types) to allow wifi per user and it works great. How to Enable User-Specific Wireless Networks in Windows 7 But in Windows 8 I cant seem to set wifi access per user.
Reinstalled lan driver and it is not showing in device manager. This is an acer aspire v3-371. Light doesn't come on when I toggle fn-f3 combo.
I think there is a service that is not running or it has been deleted. The driver files seem to have installled but it doesn't show under network adapters in device manager.
My ISP provides service only via 802.11. I use laptop A most of the time. The captive portal for the service provider only allows one login per account at a time. The policy is intended to prevent multiple people sharing one account. It's just me, I'm the only user, but very occasionally I'd like to have a 2nd laptop access the internet simultaneously. No abuse, just the simple convenience of not having to logout from A if I need to use B for 30 seconds.
What I want to set up seems simple and it probably is:
WiFi Internet <---> Laptop A <---> ethernet cable <---> Laptop B
Such that Laptop B can share A's active WiFi connection without having to request its own unique address from the ISP.
At present, Laptop A has its network interfaces set up so:
- WiFi is connected, active, functional. Selected the "Yes turn on sharing and connect to devices" in sidebar.
- Under the wired network properties IP Version 4, I manually set addresses to be
IP 192.168.10.1
Subnet 255.255.255.0
Gateway 0.0.0.0
Laptop B has only a wired network, set to
IP 192.168.10.2
Subnet 255.255.255.0
Gateway 192.168.10.1
A & B can connect directly to each other, share folders, etc.
What do I need to do in order to get laptop B to transparently use A's WiFi connection? My guess is that A needs to be set up to do some routing between the internet side and the 192.168.10 subnet, and B needs to be set up to look to A as its "ISP" ... but I don't know where to begin.
My windows 8 laptop will not connect to the wifi hotspot of my samsung galaxy note 3
Can find it on other devices such as : iphone, ipad, Mac Computer but nothing running windows 8
Randomly, my wifi disconnects many times a day (Limitted conectivity or ), sometimes every 5 minutes. I solve the problem temporarly by:
1.)Running the Troubleshoot of the wifi connection, and it resets the adapter automatically( and at the end of the troubleshotting it says: "WiFi doesnt Have a valid IP configuration, or sometimes The default gateway is not available")
2.)Sometimes the Troubleshooter cant reset the adapter, and I have to do it manually.
By resetting the adapter, the problem is solved only temporarily, because I have to do that mayby 20 times a day, sometimes more, sometimes less.
I use Windows 8 on Asus K55 VJ , Intel Centrino 2230 adapter with up to date driver.