I'm using my usb modem connected to my laptop to provide an internet access to my xbox while I was on Win 7 and it runs good but after I upgrade my OS to Win 8 now I can connect no more. It says that my ethernet connection is "unidentified network" while I still have my ICS enabled (My USB Modem still stated "shared"). I have set IPv4 to obtain automatically though.
View 9 RepliesMy windows ethernet network says 'unidentified network' every time i try and connect my Xbox to Xbox live through my laptop. Is there any way to solve this because i feel as though i have tried everything, and may as well go back to windows 7 if possible.
View 6 Replies View Relatedmy network connection on my laptop. I recently moved up to my college and am now on their network. However, I didn't have this problem at first. But recently if I go to my network connections, there is always a wired connection listed named "Unidentified Network" which has "Limited" access. The problem here is that I am not connected to any wired networks. There is no cable plugged into my computer so I don't understand how this is possible. The only thing I have installed recently is Virtualbox, just in case that could affect it.
View 5 Replies View RelatedI just got a brand new Samsung Laptop for work. I dont know a ton about windows 8 either im fairly new to it. I work at a mental hospital doing security and we are allowed to have a laptop for over night shifts. I have an Alfa wireless antenna (cause i get low signal where im stationed) along with my normal laptop Wifi.
Heres the story. I was using my laptop antenna then out of no where it said "Identified Network (no internet access)" then my internet just stopped. I had this happen on my old laptop and it lasted a few days then worked like normal again. Then i switched to mt usb antenna and it worked fine for about 20 mins then all of a sudden it went it "Identified Network (no internet access)". So I was stuck with no internet. I tried looking up fixes on my ipod and i tried 3 Ways To Fix The Unidentified Network Error in Windows 8 and it didnt work I tried How To Fix Unidentified Network Windows - YouTube and it didn't work either. I'm dying here cause I have to sit in a room for 12 hours tonight with no way to keep my self from falling asleep or entertained.
Wifi worked, walked away for 10 minutes, then found that it didn't. I would normally just reset the router, but I live in an apartment building and the router is in my landlords office.
When I did ipconfig /all, my ip started with 169, which I know isn't normal. But when I try to do a /release and /renew, I get the error "No operation can be performed on local area connection *14 while it has it's media disconnected." I am unable to attempt a wired connection, as the router is not accessible to me.
.I'm not sure if this is a router issue, or an issue with my laptop (less than a year old.) I am a grad student and I currently have to do most of my work via my iphone, which is getting very inconvenient.
I got this problem on my laptop Asus u38dt under Windows 8.1 a couple of months ago. It cannot connect to any network either via Wi-Fi or Ethernet (I tried an external USB Wi-Fi adapter as well, with the same result). In case of getting IP with DHCP, the network is shown as Unidentified network with no address assiged (IP is like 169.*). When static IP enabled, the network name is correct. But in both cases, connection is Limited and with No Internet access.
Connection can't be established with any router while other devices connect properly with them, so the problem is on the laptop side.
With all of this, any ping, even to 127.0.0.1, results in General failure.
When booted in Linux liveUSB, network works fine, so it is clearly not a hardware issue.
I tried resetting TCP/IP stack with "netsh int ip reset", reinstalling drivers, reinstalling the network adapter, and lots of other methods and still it doesn't work. Restoring system is not an option since I don't have any restoration point prior to the problem anymore.
I am frequently getting page not found errors, and am having to reload, pages take a long time to load and it's pretty much 50-50 wether it will or not load at all.
I've tried rebooting my router. I have a Vergin Media 'Super Hub' which is only two months old.
Here is a screenshot of my Ipconfig.
imgur: the simple image sharer
I am having trouble with ICS on win 8. On my old laptop (win xp) I used to be able to share my 3Connect dongle internet to connect to Xbox live. I recently got a new laptop with win 8 and whenever I share this internet connection I can never connect on my Xbox (the network to internet part fails). When everything is connected up and shared the Ethernet says 'Unidentified Network' which i believe is the cause of the problem. I've read i may require a driver update but i cannot seem to find one.
My Laptop: Toshiba Satellite C855-29N
what to do, maybe i am not setting up the connection sharing properly?
I just got done upgrading my wife's newer desktop PC that had Windows 8 on it. Did the simple (but LONG) upgrade to 8.1.
Now this PC can NOT access the internet. In Network settings, it's showing the Network Adapter and Access point have a strong signal off my Wi-Fi router, but when I open a Browser or Email NOTHING !!
I've checked Firewall settings etc.... to no avail.
Also, this PC is showing a DIFFERENT access point than my other devices that connect through my Wireless router.
Is there a way to setup network profiles or something so that when I bring my Surface Pro to work and connect to the wireless network there it will use the static ip address I have but when I disconnect and then connect to my home wifi it will go back to DHCP? On my MacBook Pro I can go into the network settings and change the location profile I have setup for networks but I don't see anything like this for Windows 8.
View 4 Replies View RelatedThis morning I installed an optional update from Windows Update. It was Ralink Technology WLAN 802.11 wireless LAN card.
Since then, when I try to print to my wireless network printer, the network would disconnect then come back on after a while. The update shows up in Update History as successfully installed but not in the installed updates. System restore is of no support here. The network configuration page shows normal. The web does not appear to be affected. I made a new network connection for the printer but it did not work.
Is there a way to reverse this update or should I uninstall the 802.11 LAN card and let windows re-install anew.
The printer is a HP Officejet Pro 8600e
Windows 8.1 Pro with Media Center,
Windows 8.1
Comcast Gateway.
Pro Media can access 8.1 Network and Homegroup.
8.1 cannot access ant Pro Media. Network Error "Windows cannot access DesktopUsersPeteDocuments' (or any other folder)
Can access IP4 address.
Windows 8.1 new machine, came with 8, updated to 8.1 then 8.1 Update.
I just bought a Lenovo Y500 a couple of days ago and it came with a pre-installed Windows 8 everything seems working fine but when it comes to Wifi it randomly disconnects a lot , sometimes shows limited access and most of the time the signal strength bars keep going up and down.
View 6 Replies View RelatedI re-installed Windows 8 yesterday evening (thought it would be quicker than to cleanup and fix my old install) and then directly upgraded it to Windows 8.1. The problem I am experiencing is quite weird: The Operating System doesn't detect the network cable.
With that being said, do not jump straight to the "Did you turn it on and off again" questions. Here is what I have done so far:
Hardware-Side: Cross-check the cable with another computer --> Working fineCross-check the wall plug with another computer --> Working fineTest the connection with the BIOS's connection diagnostic utility --> Link detected
Software-Side: Checking if Windows was up to date --> Nothing to updateUpdating the motherboard's BIOS --> Not betterUpdating the LAN's drivers with the ones I found on the manufacturer's website --> Not better
I am wondering what is wrong with my installation. It was working A1 a few days ago, except for the issues I re-installed the operating system for.
In my network 4 Desktop running windows XP all are connected LAN cable and my modem is tplink and 1 laptop running windows 8.1 pro accessing network through wireless in my laptop network place all the pcs are visible but I am not able to ping them and when I click I am getting message that Network path not found Error code 0x80070035
View 2 Replies View RelatedMy 8.1 laptop shows multiple network connections to my Samsung Smart TV --- One as "media connections" and 3 as "other connections". Both devices are on a simple wireless network using Linksys WRT54GS.
Under the "Network" page, most of the "Properties" of the TV connections are the same except for "Serial Number" and "Unique Identifier". Did I do something wrong when setting things up? Are these extra connections harmful? Should I delete some? How?
I purchased a new Windows 8, Inspiron 15 7000 series - 7537 last December. I had been using a router at a hotel for the time, and it worked correctly. When I arrived home, I had a Belkin router, and i experienced network issues in that i could not connect to the wifi. I could connect with Ethernet cable. The problem was fixed through customer support eventually, but I now have a new Comcast router, and i'm experiencing what appears to be the same or a similar issue. I can access the internet fine by wire. With wifi, it says i have access to the internet over the internet icon in the bottom right, but i cannot access webpages. I can use skype, and communicate through it.
Here is the result from the ipconfig /all :
Microsoft Windows [Version 6.2.9200]
(c) 2012 Microsoft Corporation. All rights reserved.
C:Windowssystem32>ipconfig /all
Windows IP Configuration
[Code] .....
I really need the wifi on this router working for this laptop. Let me note that it works on other laptops, so it should be an issue with hardware or settings on this laptop.
With the following problem regarding media streaming in windows 8. Up until recently I could stream video films from my HP laptop & HP desktop onto the TV via DNLA.
After following several posts on various sites it seems that when I try to start the windows media player network in the services I get the error message "windows could not start the windows media player network sharing service on the local computer.
Error 1068. The dependency group failed to start."
In the dependencies tab in the lower box of the two "the following system components depend on this service"
The box is greyed out and the words no dependencies is displayed.
I have two wifi APs in the home and only one has an Internet connection. the other is to access the wired LAN.
Last week I updated from Windows 8 to Windows 8.1 and thought everything was going well until I started getting wired LAN dropouts.
I have traced it back to 8.1 handling connection to wifi APs. In Windows 8, I was able to have "Connect automatically" for BOTH wifi adapters on this laptop. Now when I try to connect to the non-Internet AP, Windows 8.1 announces (correctly) "Limited access" and that's what Windows 8 did too. BUT, Windows 8.1 waits a few seconds then drops the connection with a useless message, "how me solve connection problems," where there is NO problem. A limited connection for the AP to the wired LAN is OK as it was in 8.
So now I am stuck with no home LAN access unless I drop the Internet AP and connect to the LAN AP.
Also, in the great wisdom of 8.1, because it is only a "limited" connection, it does not remember the Passphrase so I have to type it in every time. So much for progress.
What to do to get past this behavior and have a "limited" connection as OK as it is with Windows 8?
I upgraded to Windows 8.1 from Windows 8 and I can no longer see the files inside the folders on my networked drive. Before I upgraded I could see them, after the upgrade - not so much. The folders are fine, I can see them, just no files visible. There's no network issues as the files are visible from my Win7 machines and my wife's Windows 8 machine. All the standard default sharing and viewing settings are correct. Even if I put the direct path in File Explorer is tells me there's nothing there. I'm absolutely baffled. I have never seen this particular type of sharing issue before. I'm a pretty savvy Network Admin so the basic troubleshooting (and standard sharing settings) has been covered.
View 6 Replies View RelatedWhen I click network while i am in windows explorer, the network infrastructure is not there, only the Computer is visible there and i want to fix something by changing the properties of my modem/router on the network infrastructure.
View 5 Replies View Relatedwithout the likes of logmein?If I enable remote login on my pc, what needs to be done in my router (if anything) so I can remote in from wherever I want? I am running Windows 8.1 pro X64 router is netgear R6300
View 7 Replies View RelatedI have Windows 8.1 Pro installed signed in with my Microsoft a/c. I have some folders shared on the network through Wifi. I also have an Android device with a File Manager that has SMB capabilities.
Now I want the to connect to my shared folders through the app which works perfectly fine. But what my requirement is that if anybody else want to connect to those shared folders (with the same or another app), I have to give out my Microsoft Account password for that.
Is there a way that I can avoid this password giving? What I'm looking is for creating another set of credentials to access the shared folders without giving away my Microsoft account details. I assume I can create a local account and do the same. Is there any other way I can do this?
Unable to figure out a default setting.
Simply for the home desktop and want to share with other kit on the home network.
When I boot up it appears I have to always tweak the settings :
1) Control Panel > System > Change settings > Network ID and select under "Select the option that best describes your network" so I opt for I tick "this is a home computer; it's not part of a business network."
2 )The reboot.
All works fine and all devices can be seen and read/write in accordance with the appropriate share settings.
Now the issue is when I next reboot the
Control Panel > System > Change settings > Network ID and select under "Select the option that best describes your network" will default to "This computer is part of a business network; I use it to connect to other computers at work".
So I have to got through steps 1 and 2 again.
How to I get Windows 8.1 Pro x64 to default to the "this is a home computer; it's not part of a business network." on each boot without having to manual configure.
I have up until a few days ago been able to modify and save my network properties ok. I connected a new DisplayLink USB docking station that lead to an update of some sort. I believed this to be to do with associated drivers. I let this go ahead and it may well have nothing to do with the problems I have been having.
First of all I couldn't even see the IP parameters and kept getting an error as follows:
"In Order to Configure TCP/IP, You Must Install and Enable a Network Adapter Card"
The wired and wireless was working in environments where I could use DHCP so I was confident the hardware was ok. Uninstalling the drivers and then updating them has got me passed this problem so I can see and edit the IP parameters. However now they are never saved. I edit them, close the window, re-edit them and they are back to automatic settings! I need to use static settings in the office.
So far as I can see there are 2 possibilities:
1. I don't have permissions to save these settings, wherever they are stored. But I have administrator permissions. Where are the settings stored? I have saved them before. How can I get access to be able to save them again?
2. Something else is overwriting the settings. How do I find out what and stop it?
I want to forget a Wi-Fi network from my network list i windows 8.1 . But when I right click on that network (to forget that network) nothing happens i.e. right click menu does not open.
View 6 Replies View RelatedIn XP you used to be able to pull up a CMD Prompt and ask: net config server and this would tell how many machines/devices (other computers, printers NATs, NASs etc.) that you could hook to a machine.
they removed this function (as far as I can tell) in win7 but you can find references to the maximum number of devices that you can hook up (10 for Home , 20 for Pro) . How many devices that is for Windows 8?
My Windows 8.1 Pro machine sometimes lists someone's mobile phones in its Network list. They disappear and reappear periodically. Yesterday it was showing a device names "jewel", which, according to its properties, was an HTC EVO ("jewel" is the internal name for that model). Right now it is showing "SPH-L720", which is a Samsung mobile phone.
The machine is connected by Ethernet to Netgear R6300 router, so I presume that these devices are probably picked up over WiFi by the router. But why are they picked up and listed in Windows Network list? Does all this have something to do with router settings? A Windows 7 machine on the same network never shows anything like that.
None of these devices are mentioned in the list of WiFi attached devices in the internal router pages, meaning that they are not connected to my WiFi. At the same time my own mobile phones are successfully connected to my WiFi, but Windows does not list them in Network. So, what could it possibly be?
I'm using Windows 8.1 Professional. After the update to 8.1, I can't connect to my network printer which is connected to a Windows XP Home machine. Everything was working before the upgrade. I can currently see, connect, access and modify files on all the computers. I keep getting a message that I don't have permission to access the printer and I can't access the permissions on the Windows XP computer. I'm also using a Windows 7 computer which has no problem accessing the printer.
View 7 Replies View Relatedhow to Display the "Network Connection Icons" in the bottom right corner of the screen for "Windows 8.1 Pro".
An example of what I am referring to can be seen in the attached sample image taken from a "Windows XP" Computer.
I want to connect 2 computers together to send data from one to the other. Then I'll copy a partition to an empty computer.
View 1 Replies View Related