Maintenance :: Why Doesn't Scheduled Chkdsk Run On Restart
May 23, 2013
I have a dual boot laptop with Windows 8 and Win7. When I choose to run chkdsk /f from Command Prompt(Admin) on my Windows 8 boot drive, I get the normal message that says disk is in use and to type "Y" to schedule it to run on restart. I type "Y" and hit "Enter", but if I either Restart or Shutdown and turn laptop back on, and choose to boot Windows 8, chkdsk seems to cancel itself. I get the message to "press any key" in 2 seconds if I want to cancel the disk check, but I never press or do anything yet chkdsk seems to cancel itself. When Windows 8 boots I have looked in Event Viewer and there is no sign of any chkdsk or wininit event that says it checked disk for errors.
I have gotten the message in Action Center, to reboot to scan and repair errors which works fine. Right clicking my boot drive, going to the Tools tab and scanning drive for errors also works. My only issue is scheduling to check my boot partition for errors via command prompt.
Must I disable Fast Startup/Hybrid Boot for the scheduled chkdsk to work or something else?
View 6 Replies
ADVERTISEMENT
Apr 19, 2013
Having a problem with the Regular Maintenance waking the computer (Windows 8 on a Lenovo Q-190) to do its scheduled task as it's supposed to do. Here are the symptoms:
1. If I change the time for Scheduled Maintenance in the Action Center (Change Maintenance Settings), it WILL be reflected properly in the Properties of the Regular Maintenance Task in Task Scheduler.
2. However, if I check the box for "Allow scheduled maintenance to wake up my computer at the scheduled time" in the Action Center (Change Maintenance Settings), it WILL NOT reflect in the Properties of the Regular Maintenance Task in Task Schedular. Specially, I check the box to wake up my computer in the Action Center Maintenance Settings, but the corresponding checkmark is NOT reflected ("Wake the computer to run this task"), in the properties of the actual task in Task Scheduler.
3. I then put the checkmark directly in the Regular Maintenance Task itself ("Wake the computer to run this task"). However, at some point in the future, (not right away; I close and then reopen the task to make sure that it 'sticks'), the checkmark "disappears. Then, the task does not run at night while the computer is asleep, but runs in the morning when I wake the computer for regular use. At that point, the checkmark in the task is gone.
View 6 Replies
View Related
Jun 21, 2014
I have Automatic Scheduled Maintenance set to run at 3:00AM. I get to this setting by going to Control Panel > Action Center > Maintenance > Change maintenance settings. I also have the box for "Allow scheduled maintenance to wake up my computer" checked.
However, I note that if I put my computer to sleep for a few days, when I wake it back up, Automatic Scheduled Maintenance has NOT run. I can tell this because my antivirus definitions are out-of-date and haven't been updated since I put the computer to sleep.
how to figure why it's not waking up for Scheduled Maintenance? Is it possibly a BIOS setting? Do I have to manually add it to Task Scheduler? I'm running Windows 8.1 Update 1, ASRock Z87E-ITX mobo, Intel i7-4770S CPU, Samsung 840 EVO mSATA SSD, 16GB RAM.
View 4 Replies
View Related
May 15, 2014
Windows 8 waking & sleeping issues:
This is a backup task I've been using for several years with Windows 7 machines, but only recently started adding to Windows 8.1 boxes. The strange behavior is as follows:
-If the computer is on, the task will start at the scheduled time and do it's thing.
-If the computer is asleep (S3), it will wake up at the scheduled time, but the task never runs??!!
I have attached the XML export of the task ....
View 3 Replies
View Related
Feb 23, 2014
Almost every morning for the last month or so I will discover my computer is running (monitor off, but computer not in sleep mode as it should be). To figure out what was waking it, I went to cmd prompt and used the command "powercfg -waketimers":
C:WINDOWSsystem32>powercfg -waketimers
Timer set by [SERVICE] DeviceHarddiskVolume1WindowsSystem32svchost.exe (Sys
temEventsBroker) expires at 4:01:43 AM on 2/23/2014.
Reason: Windows will execute 'NT TASKMicrosoftWindowsTaskSchedulerRegular
Maintenance' scheduled task that requested waking the computer. I also tried "powercfg -lastwake":
[code]...
So it appears that "Regular Maintenance" is waking my computer. But why isn't it returning to sleep? It used to.
I then went to Power Options > Edit Plan Settings. These settings are still correct (Put the computer to sleep: 30 minutes).
Next I checked the Task Scheduler. Under "Active Tasks" I found "Regular Maintenance".
Next run time: 3:53 AM tomorrow. That very closely matches the 4:01 AM listed in "powercfg -waketimers", but I find it odd that it is after the scheduled time.
Triggers: At 3:00 AM every day
Doubling clicking on Regular Maintenance provides more detail.
Last Run Time: 5:46 AM
Last Run Result: operation completed successfully
However, another item in here is "Idle Maintenance".
Triggers: when computer is idle
Last Run Time: 5:46 AM
Last Run Result: The process terminated unexpectedly. (0x8007042B)
All of my drive partitions are scheduled to optimize weekly rather than daily. My computer is waking up daily.
Last night I turned all scheduled optimization off. This morning my computer was again woken from it sleep.
The cmd prompt gives me the same reason for the wake (Regular Maintenance).
Task Scheduler shows Regular Maintenance as:
Last Run Time: This morning at 4:36 AM
Last Run Result: The last run of the task was terminated by the user. (0x41306)
Under Idle Maintenance it shows nothing for this morning.
What does this mean? Optimization ran despite me turning it off?
View 6 Replies
View Related
Jan 16, 2014
After I get to the event viewer, where do I go from there?
View 2 Replies
View Related
Apr 25, 2013
I have read that Windows 8 has a new Chkdsk, which checks the file-system integrity in background. I'm using Windows 8 Pro 64bit (and NTFS file-system on all drives).
Does this improved Chkdsk check the file-system just when the computer is not used, or does it check it also while the user is working? Or does it scan the drives just when it's maintenance time?
Does it still make sense to run a manual Chkdsk on some occasions, or can I just not worry and let Chkdsk do its checks automatically? Such occasions would be for example after the computer completely hangs and I have it to brutally turn it off with the power switch (happened lately with a Linux live-CD), or after problems with the electric line (loss of power/power outage, resulting in instant turning-off).
In other words, is it useful to run a manual Chkdsk when there is a suspect that something could have gone wrong with the file-system, or can I just continue working and let Chkdsk do its verifications?
How long should it take (more or less) from when a file-system corruption arises, to when it gets detected by Chkdsk?
What worries me, is that not doing a Chkdsk at once, to repair eventual problems, may make the problems get bigger while the hard disk (or SSD) gets used. And they could get such big that they could not get repaired anymore (just an hypothesis).
View 2 Replies
View Related
Jun 4, 2014
It seems that Windows 8.1 Pro's scheduled defrag is consolidating free space, which is taking forever on one of my 2 TB data drives, which has about 300 GB free space. I stopped it at about 9%, and dfrgui immediately showed it as "OK (0% fragmented)". Clicking its Optimize button resulted in the defrag phase completing almost immediately, but then it was back to consolidating free space, starting at 5% this time. According to Task Manager, it's read/writing about 40 MB/sec, and the Active Time is over 90%. I really don't want this to go on for hours and hours and potentially repeat itself during future scheduled scans. Is it possible to alter this behavior, or should I just disable the weekly defrag task?
View 7 Replies
View Related
Jun 13, 2014
Today I've tried doing a Chkdsk scan on my primary drive. Through the console, I entered this line to start the process on a re-boot 'chkdsk /f /r c:'.
I afterwards left it to do it's work for the next 1 and half hours '6:40-8:10pm', during this time I went to check on the progress of the scan and what I saw was that it was only '10%' into completion, this confused me greatly as previous computers that I have owned would atleast be around 70, or 80% percent completed, so not knowing what to do, I did a cold-boot.
From what I can tell, no visible damage has afflicted said the drive I did the chkdsk scan process on, but I would still very much like to know why my scan is hanging.
View 9 Replies
View Related
Dec 28, 2012
I'm having troubles with a disk check.
Firstly, I'd like to mention that I've had this PC for a while... I've even taken the whole thing apart and swapped out all of the components (slowly upgraded over time). It's actually at the stage where I've been left with all the old parts as spares, and put everything back together, almost exactly as it was when I bought it. All in all, the initial build is probably 2 or 3 years old now (for the most part, the specs can be found here).
After formatting the hard drive, putting things together back with the old build, and booting up Windows 8 onto it as a gift for my dad, most things were working fine, but one exe file which I copied across wasn't running (at least one which I noticed). I checked up the error code, found people with similar problems, and heard it could just be that the file was corrupted.
So, to get to the main point... I figured it wouldn't hurt to run a disk check, in case there were any other errors or problems. I knew it would take a while, so I opened command prompt, and typed in "chkdsk C: /r", before hitting enter, letting it schedule the disk check for next startup, rebooting the PC, and then leaving it to do its thing. It's been running probably for about 4 or so hours now, and for most of that time it's been at 27% on "Scanning and repairing drive (C:)". Normally I'd just give in and force shut down at this point, but I'm wondering... what's the best course of action if it doesn't get anywhere with this?
I'd really prefer not to force shut down, in case it causes any errors... I mean to say the least it's taken some effort and persistence to get the old build up and running again.
View 9 Replies
View Related
Feb 24, 2014
I have some questions regarding the new Chkdsk in Windows 8 (I'm using Windows 8.1 Pro 64bit).
note that Windows 8's Chkdsk has changed considerably since the previous Windows versions; so if you know about the Chkdsk in Windows 7 or previous Windows versions, this could not apply to the Chkdsk in Windows 8.
I also point out that I'm talking about the GUI version, accessible from the drive's properties Window.
My main questions are: when Chkdsk has finished scanning, and the results window appears, can I at once proceed with the following, or should I wait some time:
1) In case of an external USB drive, disconnect the hard drive (with "safely remove hardware", even if the cache is turned off), and turn it off.
2) In case of an internal drive (HDD or SSD), reboot Windows, or turn off the computer.
My worry is that if I would disconnect a USB drive, or reboot or turn off the PC in case of an internal drive, before the Chkdsk-related activity is finished, then the file-system of the disk in question could get damaged.
My doubts come from the following facts:
- I have been told that when the Chkdsk results window appears, this means that Chkdsk has finished working with that drive; but I have noticed that some short drive activity is happening some seconds (about 6) after the results window appears (should be a write activity, not sure if also read activity). I noticed this by observing the LED on my USB drives, and also by monitoring the drives in question with Windows 8's new Taskmanager.
- In case of disconnecting USB drives, I have been told that I can be sure that if some drive activity is happening, then the "safely remove hardware" feature won't have effect, and would warn me that there is disk access going on; but I have tried to select "safely remove hardware" while Chkdsk was in the middle of a scan, and the result was that Chkdsk got interrupted (with an error messsage appearing probably from Chkdsk), and the USB hard drive got removed. Though this seems not to have caused any file-system errors (I did another Chkdsk scan later).
You may think that I just need to look at the drive's LED, or monitor the drive's activity with the new Taskmanager, and take note of after how much time the drive activity ceases. Then I would just need to wait so long before disconnecting the USB drive, or rebooting or turning off the PC.
My problem here is that I'm not sure if the new Taskmanager, or the drive's LED, are sensible enough to detect even the smallest disk access, which could get unnoticed. I'm not sure how much I should wait... seconds? Minutes? What do you think? Perhaps there's no need to wait at all?
I did some tests by disconnecting (with "safely remove hardware") a USB drive shortly after doing a Chkdsk on it. Then I did another Chkdsk after turning it on again. I didn't get any error message from Chkdsk. But I'm still worried that there could be an unfortunate moment, during which a disconnection (still with "safely remove hardware") could cause problems, perhaps because in that moment a write operation could be in process.
I think I have read that the new Chkdsk in Windows 8 uses VSS ("Shadow Copy") to check the drives while keeping them online. With this new Chkdsk, I think it is possible to continue using the drive while the scan is happening, even on the system drive.
I was thinking about this: is it possible that the short activity which I have noticed after Chkdsk's results window appears, comes from this Shadow Copy Service, which is "unmounting" (?) the shadow copy used by Chkdsk?
If this is true, is it important to let the "unmounting" task happen, or can I disconnect, reboot, or turn off before it starts? And what happens if I interrupt this "unmounting" task in the middle, while it is in process?
Does it make some sense to wait some time after doing a Chkdsk, or can I at once proceed to disconnect the USB drive, or reboot or turn off the PC (in case of internal drives)?
View 1 Replies
View Related
Mar 3, 2014
I have been having trouble with my laptop lately. I was trying to install a new driver for my graphics card when my computer suddenly rebooted, I was forced to refresh Windows 8, then an even bigger problem happened, windows kept thinking that it was not registered but when i go to system from the control panel it says it is registered and gives me the product code, so I read somewhere that doing the chkdsk scan will fix this so i did it, first it was stuck 27% for about 4 hours then it is currently stuck at 100%, its been at 100%for about 13 hours now. I do not know what to do, afraid to force restart, might cause errors.
View 7 Replies
View Related
Apr 8, 2014
Delay Chkdsk start up time at OS Boot | Windows 8 & 8.1 (Or Disable Altogether)
Previous to Windows 8 if Chkdsk needed to run without prompt the user had the ability to cancel if so desired. Since Windows 8, the user input has been removed.
At the least, you can change the delay setting as follows:
Modify DWORD "AutoChkTimeout"
IMAGE ONE:
1. Open Regedit:
One way to open regedit is to hit the Winkey+S and type regedit, hit enter when you see it appear.
2. Navigate to the following registry key:
Code: HKEY_LOCAL_MACHINESYSTEMCurrentControlSetControlSession Manager 3. Click on the folder "Session Manager"
4. In the right hand pane you will see registry values. Right click on the value "AutoChkTimeout" and select "Modify" (See image one)
If the value is missing, create it (See image two)
5. Change the "Value data:" to the desired delay time of your choice.
e.x. Changing the value to 10, will delay the Chkdsk start time by 10 seconds.
Click OK, close the registry.
Finished.
Create DWORD "AutoChkTimeout"
IMAGE TWO:
If the registry value "AutoChkTimeout" is not present:
Right click on an empty space in the right hand pain (in folder "Session Manager")
Select "New"
Select "DWORD (32-Bit) Value
Name it "AutoChkTimeout" (No Quotation Marks "")
Follow step 4. above.
Remember:
Name = AutoChkTimeout
Base = Hexadecimal
Value Data = Delaytime (in seconds)
DISABLE automatic repair in Windows 8 & Windows 8.1
If you would like to disable automatic repair altogether:
1. Open the command prompt as Administrator (an elevated instance). If you have no idea how to open an elevated command prompt. Hit Winkey+S type in cmd.exe, when it appears, right click on the name and choose "Run as administrator"
2. Type the following text into the cmd window
Code: bcdedit /set recoveryenabled NO
You have now disabled the Automatic repair function.
To reinable: Follow step 1 and in step 2 type in the following text:
Code: bcdedit /set recoveryenabled YES
Having disabled the Automatic repair feature, you can follow Brink's tutorial on manually running Chkdsk > Here:
CHKDSK - Check a Drive for Errors in Windows 8
View 3 Replies
View Related
Jun 21, 2013
I have had to do a system restore on my desktop 2 times because the Microsoft update rendered my windows 8 desktop useless unless in safe mode, THEN it showed my mouse pointer. the unifying software shows the little orange unifying logo every time i move my mouse, but no pointer. so i just disabled Microsoft updates.
On the laptop, it's my friends and his mousepad/trackpad died so i gave him my old mx anywhere k360 keyboard and tried to pair it with the software, SAME issue. I am not going to system restore his laptop but i believe the mouse that's on my desktop is the 810 gaming mouse? I had to do a system restore twice and now it's happening on my friends laptop.
I disabled windows updates and restarted my computer because i installed a program. when it booted, again, no mouse pointer again, so it's not the windows update. so i had to do a system restore again....
View 2 Replies
View Related
Mar 10, 2013
So I've tried to shutdown my PC 2 days ago with the shutdown key in the settings menu (or windows menu because I'm using Start8) and it doesn't work, same for restart, sleep and all that option, so what to do?
View 9 Replies
View Related
Jan 25, 2014
I've had my modem connected straight to my computer via ethernet cable and never really had any problems. I recently downloaded itunes to listen music on my ipod and i know this probably isn't the problem but weeks later i was prompted to download an update for itunes and of course I clicked restart after update but start up computer and internet did not work. It was this "Ethernet doesn't have a valid IP configuration."
I've tried resetting the modem and nothing. It is worth noting that I reformatted to see if it would fix it but nothing. but once i connect my modem directly to my laptop it works perfectly fine. I also including attachments so i could possibly be better assisted. Also worth noting my motherboard is a Asus crosshair formula IV which unfortunately doesn't have updated windows 8 drivers but never gave me problems before. the ipconfig with black background is the laptop ipconfig.
View 6 Replies
View Related
Jun 8, 2013
I am dual booting Windows 8 and win7. I actually have Windows 8 installed on its own hard drive and win 7 installed in its own hard drive. The win7 hard drive has been in use for the past 2 years and I have had Windows 8 running for about a week now. I purchased another hard drive for Windows 8 and left the old Win7 as it was.
I also have 3 other hard drives in the system. Everything is formatted NTFS.
So my system is as follows
Drive C - Boot Drive - I physically swap out the dedicated hard drive for Win 8 or Win 7
Drive D - internal 250 GB sata drive
Drive F - internal 250 GB sata drive
Drive H - internal 250 GB hard drive.
I have been running this config for about 2 years under Win7 with no problems.
The problem that I have now is when I swap the boot drive and boot up a different OS than last time (Like booting Windows 8, powering down system, swap boot drive, boot Win7) the system always says that there are problems on the 3 non-boot drives. It runs chkdsk(it least that is what it look like) and processes the 3 non boot disks one at a time which take about 10-12 minutes for all 3. Most of the time it finds no problems, but about 1 out of 5 boots will find a problem with one of the disks and then fixes it. The disks seem to be OK while I am running. I then power down and swap boot drive and reboot the other os and we start all over again. I am powering the system completely down for each reboot to make sure that the disk cache is flushed.So far the disk problems have been fixed by chkdsk at boot, but I am sure the day will come when the disk cannot be fixed and I will loose data.
View 3 Replies
View Related
Dec 12, 2013
I just built a desktop with a sabertooth x79 motherboard, and am running Windows 8.1 pro 64-bit. When I click the UEFI BIOS Firmware live tile via the change PC settings>update and recovery>recovery>etc. my computer reboots normally to Windows and will not open BIOS. I have tried accessing it using the delete and f2 keys, but this does nothing either.
I am up to date in terms of my BIOS, and am definitely running UEFI and not legacy.
View 2 Replies
View Related
Jul 31, 2013
I should have had an automatic system restore backup today (It's been 7 days since the last system backup). It didn't happen, so I checked the Task Scheduler, and I see that System Restore task last ran yesterday morning at 8:46. Why didn't it run this morning?
View 9 Replies
View Related
Nov 3, 2012
I am running win 8 pro on a toshiba laptop R700 S1312 64 bit with 8G Ram. I am getting numerous 10016 errors (same error) after every restart.
The application-specific permission settings do not grant Local Launch permission for the COM Server application with CLSID
{7022A3B3-D004-4F52-AF11-E9E987FEE25F}
and APPID
{ADA41B3C-C6FD-4A08-8CC1-D6EFDE67BE7D}
to the user Don-PCDonald SID (S-1-5-21-2075968696-349866310-2035089026-1001) from address LocalHost (Using LRPC) running in the application container Unavailable SID (Unavailable). This security permission can be modified using the Component Services administrative tool.
View 9 Replies
View Related
Feb 2, 2013
I've had my windows 8 computer since December and for the past month or so it will not restart or shut down unless I do a hard shut down with the power button. When hitting restart it starts to shut down, then comes up with "restarting" screen and just stays there, never moves from there. On shut down it just freezes after closing down windows. It can't be good always shutting down via the power button. I haven't added any new programs at all so not sure why this started happening.
View 9 Replies
View Related
Aug 19, 2014
This states that another program is in progress or installing, or the system is waiting to restart.
The problem is I have all free programs; MBAM, SpywareBlaster, and Defender and only Defender has real protection.
I have checked task manager for other programs that may be running.
Also, my wife's laptop is doing the same thing. Hers has been refreshed about 2 months agao and mine was reinstalled about 2 weeks ago. This has just begun.
Either Defender in both machines is faulty, MS is having an issue, there is an issue on my end with both pcs or??
I find it odd that both machines are doing the same thing.
View 9 Replies
View Related
Sep 15, 2014
Since I have installed windows 8.1, every time for example if I don't use my laptop for 10 minutes, and because of the battery saving setting plan, my display turns off. Before I installed windows 8.1, I could just move a mouse or press any key and display would turn on, but since the installation I have to restart my laptop (Samsung ultrabook), even if I can hear it's on and working.
View 4 Replies
View Related
Mar 9, 2014
My system has been on completely since 8.1 and has never needed to restart until I did some updates today.
Now I'm not really concerned about shutdown or restart as I will manually shut down the PC if I'm going somewhere for an extended time "I never leave anything on, power for the entire house is shut off" and will shut it off until I get back.
But the slow login is really killing me as it used to take 1 second to hear that little "tick" from the speakers and I'd see the login/splash page, but as of today I will hear that "tick" but the windows dotted circle will spin for oh.. 30 seconds than I can see my splash screen.
I've scanned my C: and D: disks, ran defender, antivirus, etc and all came back fine and I even have 90GB free out of my 120gb drive.
View 1 Replies
View Related
Mar 8, 2013
I have been running Win 8 on my ASUS Q200E Laptop and have been puzzled by the difference in the startup times between a cold, power off start up and a restart startup. On a cold startup, the desktop is completely ready to use in about 20 seconds. With a restart, it takes about 38 seconds to get to the same point.
View 3 Replies
View Related
Oct 4, 2013
My computer startup was fine but shutting it down or restart it are extremely slow until it takes nearly 5-10 minutes to do so. Any hint for me to solve this issue?
View 3 Replies
View Related
Jun 8, 2013
In Windows 8, I am creating a scheduled task:
When confirm all dialog windows, the error message "unsupported request" is displayed. How come?
View 3 Replies
View Related
Jan 13, 2014
I just had my laptop install Windows 8.1 tonight. It's a clean install, by the way. Now the problem is I noticed that every time I restart my laptop it's power plan reverts back to "power saver", I had it set on "high performance" before. I own a Samsung laptop, model is NP535U3C-A01, Series 5.
Processor: AMD A6-4455
Memory: 8 GB
Graphics card: AMD Radeon HD 7500G
It stops charging at 99%.
View 6 Replies
View Related
Oct 31, 2012
I'm getting soo many problems regarding booting after upgrading to Windows 8 Pro yesterday on my Asus Zenbook UX32A.
Specs:
2nd Gen i3-2367M processor @ 1.4GHz (for Ultrabooks)
6GB DDR3 RAM
500GB HDD + 30GB SSD (for Fast Resume, etc.)
Issue # 1: Whenever I Restart or Shut Down, the system HANGS there and does not progress *most* of the time. To fix this I have to always resort to holding the power button.
Issue # 2: When I boot the PC up, it takes SO long for me to get to the Start menu, around 1:15-1:30 min, which is longer than it took me on W7. I know I have an HDD, but this is abnormally long to me. Once in a blue moon, I will boot up in a matter of 30-40 seconds (which I think is how long it should take), but mostly it takes really long.
Issue # 3: To test the above 2 issues, I went ahead and opened msconfig from Run, and disabled all Non-Microsoft services except AVG to check. When I shutdown and power on - everything is fine, shuts down nicely, powers on nicely - however, the second time I do this, the system will hang on shut down, or will hang on start up, sometimes I can hear the startup sound but nothing on the screen, all sorts of weird actions.
Issue # 4: This one is funny. On standby (lid down), the system will restart itself. Happened while I was sleeping, I could hear the boot sound.
EDIT: The problem is still there when I disable 'Fast Start-Up' in Power Options. The problem is due to the processor state, it keeps resetting to 100%.
View 9 Replies
View Related
May 23, 2014
I have an Asus laptop running on Windows 8 that starts up to the initial Asus logo for a minute and then restarts over and over. I've already tried pressing f8 and it does nothing so I cannot get anywhere to attempt to fix the problem.
Unfortunately I do not have the Windows disk so I'm looking for a solution outside of having to buy another one and wiping the hard drive to reinstall.
View 9 Replies
View Related
Dec 1, 2012
My Asus UX32A has been crashing sometimes during shutdown/restart/hibernate since I updated to Windows 8.
View 1 Replies
View Related
