Maintenance :: Where Is The CHKDSK Log Located In Windows 8
Jan 16, 2014After I get to the event viewer, where do I go from there?
View 2 Replies
ADVERTISEMENT
Maintenance :: Windows 8.1 Chkdsk Scan Hanging?
Jun 13, 2014Today I've tried doing a Chkdsk scan on my primary drive. Through the console, I entered this line to start the process on a re-boot 'chkdsk /f /r c:'.
I afterwards left it to do it's work for the next 1 and half hours '6:40-8:10pm', during this time I went to check on the progress of the scan and what I saw was that it was only '10%' into completion, this confused me greatly as previous computers that I have owned would atleast be around 70, or 80% percent completed, so not knowing what to do, I did a cold-boot.
From what I can tell, no visible damage has afflicted said the drive I did the chkdsk scan process on, but I would still very much like to know why my scan is hanging.
Maintenance :: Windows 8 / New Chkdsk And Drive Activity After Scan
Feb 24, 2014 I have some questions regarding the new Chkdsk in Windows 8 (I'm using Windows 8.1 Pro 64bit).
note that Windows 8's Chkdsk has changed considerably since the previous Windows versions; so if you know about the Chkdsk in Windows 7 or previous Windows versions, this could not apply to the Chkdsk in Windows 8.
I also point out that I'm talking about the GUI version, accessible from the drive's properties Window.
My main questions are: when Chkdsk has finished scanning, and the results window appears, can I at once proceed with the following, or should I wait some time:
1) In case of an external USB drive, disconnect the hard drive (with "safely remove hardware", even if the cache is turned off), and turn it off.
2) In case of an internal drive (HDD or SSD), reboot Windows, or turn off the computer.
My worry is that if I would disconnect a USB drive, or reboot or turn off the PC in case of an internal drive, before the Chkdsk-related activity is finished, then the file-system of the disk in question could get damaged.
My doubts come from the following facts:
- I have been told that when the Chkdsk results window appears, this means that Chkdsk has finished working with that drive; but I have noticed that some short drive activity is happening some seconds (about 6) after the results window appears (should be a write activity, not sure if also read activity). I noticed this by observing the LED on my USB drives, and also by monitoring the drives in question with Windows 8's new Taskmanager.
- In case of disconnecting USB drives, I have been told that I can be sure that if some drive activity is happening, then the "safely remove hardware" feature won't have effect, and would warn me that there is disk access going on; but I have tried to select "safely remove hardware" while Chkdsk was in the middle of a scan, and the result was that Chkdsk got interrupted (with an error messsage appearing probably from Chkdsk), and the USB hard drive got removed. Though this seems not to have caused any file-system errors (I did another Chkdsk scan later).
You may think that I just need to look at the drive's LED, or monitor the drive's activity with the new Taskmanager, and take note of after how much time the drive activity ceases. Then I would just need to wait so long before disconnecting the USB drive, or rebooting or turning off the PC.
My problem here is that I'm not sure if the new Taskmanager, or the drive's LED, are sensible enough to detect even the smallest disk access, which could get unnoticed. I'm not sure how much I should wait... seconds? Minutes? What do you think? Perhaps there's no need to wait at all?
I did some tests by disconnecting (with "safely remove hardware") a USB drive shortly after doing a Chkdsk on it. Then I did another Chkdsk after turning it on again. I didn't get any error message from Chkdsk. But I'm still worried that there could be an unfortunate moment, during which a disconnection (still with "safely remove hardware") could cause problems, perhaps because in that moment a write operation could be in process.
I think I have read that the new Chkdsk in Windows 8 uses VSS ("Shadow Copy") to check the drives while keeping them online. With this new Chkdsk, I think it is possible to continue using the drive while the scan is happening, even on the system drive.
I was thinking about this: is it possible that the short activity which I have noticed after Chkdsk's results window appears, comes from this Shadow Copy Service, which is "unmounting" (?) the shadow copy used by Chkdsk?
If this is true, is it important to let the "unmounting" task happen, or can I disconnect, reboot, or turn off before it starts? And what happens if I interrupt this "unmounting" task in the middle, while it is in process?
Does it make some sense to wait some time after doing a Chkdsk, or can I at once proceed to disconnect the USB drive, or reboot or turn off the PC (in case of internal drives)?
Maintenance :: Delay Chkdsk Startup Time At OS Boot - Windows 8 And 8.1
Apr 8, 2014Delay Chkdsk start up time at OS Boot | Windows 8 & 8.1 (Or Disable Altogether)
Previous to Windows 8 if Chkdsk needed to run without prompt the user had the ability to cancel if so desired. Since Windows 8, the user input has been removed.
At the least, you can change the delay setting as follows:
Modify DWORD "AutoChkTimeout"
IMAGE ONE:
1. Open Regedit:
One way to open regedit is to hit the Winkey+S and type regedit, hit enter when you see it appear.
2. Navigate to the following registry key:
Code: HKEY_LOCAL_MACHINESYSTEMCurrentControlSetControlSession Manager 3. Click on the folder "Session Manager"
4. In the right hand pane you will see registry values. Right click on the value "AutoChkTimeout" and select "Modify" (See image one)
If the value is missing, create it (See image two)
5. Change the "Value data:" to the desired delay time of your choice.
e.x. Changing the value to 10, will delay the Chkdsk start time by 10 seconds.
Click OK, close the registry.
Finished.
Create DWORD "AutoChkTimeout"
IMAGE TWO:
If the registry value "AutoChkTimeout" is not present:
Right click on an empty space in the right hand pain (in folder "Session Manager")
Select "New"
Select "DWORD (32-Bit) Value
Name it "AutoChkTimeout" (No Quotation Marks "")
Follow step 4. above.
Remember:
Name = AutoChkTimeout
Base = Hexadecimal
Value Data = Delaytime (in seconds)
DISABLE automatic repair in Windows 8 & Windows 8.1
If you would like to disable automatic repair altogether:
1. Open the command prompt as Administrator (an elevated instance). If you have no idea how to open an elevated command prompt. Hit Winkey+S type in cmd.exe, when it appears, right click on the name and choose "Run as administrator"
2. Type the following text into the cmd window
Code: bcdedit /set recoveryenabled NO
You have now disabled the Automatic repair function.
To reinable: Follow step 1 and in step 2 type in the following text:
Code: bcdedit /set recoveryenabled YES
Having disabled the Automatic repair feature, you can follow Brink's tutorial on manually running Chkdsk > Here:
CHKDSK - Check a Drive for Errors in Windows 8
Maintenance :: Automatic And Manual Chkdsk
Apr 25, 2013I have read that Windows 8 has a new Chkdsk, which checks the file-system integrity in background. I'm using Windows 8 Pro 64bit (and NTFS file-system on all drives).
Does this improved Chkdsk check the file-system just when the computer is not used, or does it check it also while the user is working? Or does it scan the drives just when it's maintenance time?
Does it still make sense to run a manual Chkdsk on some occasions, or can I just not worry and let Chkdsk do its checks automatically? Such occasions would be for example after the computer completely hangs and I have it to brutally turn it off with the power switch (happened lately with a Linux live-CD), or after problems with the electric line (loss of power/power outage, resulting in instant turning-off).
In other words, is it useful to run a manual Chkdsk when there is a suspect that something could have gone wrong with the file-system, or can I just continue working and let Chkdsk do its verifications?
How long should it take (more or less) from when a file-system corruption arises, to when it gets detected by Chkdsk?
What worries me, is that not doing a Chkdsk at once, to repair eventual problems, may make the problems get bigger while the hard disk (or SSD) gets used. And they could get such big that they could not get repaired anymore (just an hypothesis).
Maintenance :: Why Doesn't Scheduled Chkdsk Run On Restart
May 23, 2013I have a dual boot laptop with Windows 8 and Win7. When I choose to run chkdsk /f from Command Prompt(Admin) on my Windows 8 boot drive, I get the normal message that says disk is in use and to type "Y" to schedule it to run on restart. I type "Y" and hit "Enter", but if I either Restart or Shutdown and turn laptop back on, and choose to boot Windows 8, chkdsk seems to cancel itself. I get the message to "press any key" in 2 seconds if I want to cancel the disk check, but I never press or do anything yet chkdsk seems to cancel itself. When Windows 8 boots I have looked in Event Viewer and there is no sign of any chkdsk or wininit event that says it checked disk for errors.
I have gotten the message in Action Center, to reboot to scan and repair errors which works fine. Right clicking my boot drive, going to the Tools tab and scanning drive for errors also works. My only issue is scheduling to check my boot partition for errors via command prompt.
Must I disable Fast Startup/Hybrid Boot for the scheduled chkdsk to work or something else?
Maintenance :: Stuck Scanning / Repairing C Drive (Chkdsk)
Dec 28, 2012I'm having troubles with a disk check.
Firstly, I'd like to mention that I've had this PC for a while... I've even taken the whole thing apart and swapped out all of the components (slowly upgraded over time). It's actually at the stage where I've been left with all the old parts as spares, and put everything back together, almost exactly as it was when I bought it. All in all, the initial build is probably 2 or 3 years old now (for the most part, the specs can be found here).
After formatting the hard drive, putting things together back with the old build, and booting up Windows 8 onto it as a gift for my dad, most things were working fine, but one exe file which I copied across wasn't running (at least one which I noticed). I checked up the error code, found people with similar problems, and heard it could just be that the file was corrupted.
So, to get to the main point... I figured it wouldn't hurt to run a disk check, in case there were any other errors or problems. I knew it would take a while, so I opened command prompt, and typed in "chkdsk C: /r", before hitting enter, letting it schedule the disk check for next startup, rebooting the PC, and then leaving it to do its thing. It's been running probably for about 4 or so hours now, and for most of that time it's been at 27% on "Scanning and repairing drive (C:)". Normally I'd just give in and force shut down at this point, but I'm wondering... what's the best course of action if it doesn't get anywhere with this?
I'd really prefer not to force shut down, in case it causes any errors... I mean to say the least it's taken some effort and persistence to get the old build up and running again.
Maintenance :: Scanning And Repairing Drive C (chkdsk) Stuck At 100%
Mar 3, 2014I have been having trouble with my laptop lately. I was trying to install a new driver for my graphics card when my computer suddenly rebooted, I was forced to refresh Windows 8, then an even bigger problem happened, windows kept thinking that it was not registered but when i go to system from the control panel it says it is registered and gives me the product code, so I read somewhere that doing the chkdsk scan will fix this so i did it, first it was stuck 27% for about 4 hours then it is currently stuck at 100%, its been at 100%for about 13 hours now. I do not know what to do, afraid to force restart, might cause errors.
View 7 Replies View RelatedDell :: XPS 15Z Windows 8 Unknown Device Located On PCI Express Root Complex
Nov 7, 2013I have a Dell XPS 15Z, which I bought off a friend. They recently updated to Windows 8 and so now thats what I have. But when i go into my drivers its telling me that i have an unknown driver. no solutions online have answered my questions though some came close. So, this is what i know:
Unknown Device
Device Type: Other devices
Manufacturer: Unknown
Location: on PCI Express Root Complex
Hardware Ids:
ACPIVEN_SMO&DEV_8800
ACPISMO8800
*SMO8800
i don't know if this is related but my laptop also wont charge. I just bought a new AC Adapter to replace the one i had, and it still isn't charging. The light blinks red 4-5 times and blue/green once. ive searched online to see what the problem is but i cannot do some of the fixes as the computer is at 0% battery.
Maintenance :: Win 8 / 7 Dual Boot Results In Chkdsk Run At Boot?
Jun 8, 2013I am dual booting Windows 8 and win7. I actually have Windows 8 installed on its own hard drive and win 7 installed in its own hard drive. The win7 hard drive has been in use for the past 2 years and I have had Windows 8 running for about a week now. I purchased another hard drive for Windows 8 and left the old Win7 as it was.
I also have 3 other hard drives in the system. Everything is formatted NTFS.
So my system is as follows
Drive C - Boot Drive - I physically swap out the dedicated hard drive for Win 8 or Win 7
Drive D - internal 250 GB sata drive
Drive F - internal 250 GB sata drive
Drive H - internal 250 GB hard drive.
I have been running this config for about 2 years under Win7 with no problems.
The problem that I have now is when I swap the boot drive and boot up a different OS than last time (Like booting Windows 8, powering down system, swap boot drive, boot Win7) the system always says that there are problems on the 3 non-boot drives. It runs chkdsk(it least that is what it look like) and processes the 3 non boot disks one at a time which take about 10-12 minutes for all 3. Most of the time it finds no problems, but about 1 out of 5 boots will find a problem with one of the disks and then fixes it. The disks seem to be OK while I am running. I then power down and swap boot drive and reboot the other os and we start all over again. I am powering the system completely down for each reboot to make sure that the disk cache is flushed.So far the disk problems have been fixed by chkdsk at boot, but I am sure the day will come when the disk cannot be fixed and I will loose data.
This File Is No Longer Located Here - Verify Items Location And Try Again
Jan 10, 2014I had created a folder in my external hard drive.
The problem is that i am not able to delete or move it.It throws me an error telling "This file is no longer located here.Verify items location and try again."
The properties of the file are like last modified etc are also not shown.It contains some files but shows that it is using 0 bytes.
I want to delete it.
Missing Files After Chkdsk Repair On Windows 8.1?
May 7, 2014So I did a disk repair for one of my hard drives (not the system drive ) using check disk because I could not open my folders it would say they were corrupted. This followed me powering off my pc while it was shutting down. So after the chkdisk repair my drive was now functioning ok except for one thing; some of my files and were missing. I could not see any Found.xxx folder even after showing hidden files. I then checked my free space and noticed that it had not changed inspite of the files missing one of which was a folder containing 250GB of data which I cant afford to lose. This has led me to think my data is still on the drive but just hidden somehow. How can I recover this data.
View 6 Replies View RelatedCan't Access Safe Mode Or Run Chkdsk?
Dec 11, 2013Win 8 Pro..I am trying to fix an error that is causing my desktop to randomly reboot.
I wanted to run chkdsk from safe mode, however, tapping f8 doesn't work for me.
Tried to restore a backup and paragon merged all the drives into one file and says the structure is different and I may lose data.
Win 8 will not let me stop chkdsk with any key press.
Debugging :: BSOD After Running Chkdsk For 120 Hours On Broken HDD
Jul 19, 2014I have a friend with his broken HDD, ran chkdsk on it , after 120 hours it had gone up to 45% only and I got a bluescreen while playing dota 2 so chkdsk was interupted, when the pc jumped back I could access the HDD but it was super slow and after a restart I couldnt access it anymore, I unplugged the HDD thought it was gone forever and today I got another BSOD while I was on youtube. I got really scared cause I have had tons of trouble with this PC but after I switched out a damaged motherboard it all dissapeared and the PC was finally working 100%.
I deleted the old dumpfiles cause they were from when my motherboard was broken, if you find traces of the old dumpfiles, ignore them cause that problem is solved, its dumpfiles from july (its 2 of them) that are making me scared if I made a big mistake letting chkdsk run for that long on a bad hdd ...
SF diagnostic tool file:
SF_19-07-2014.rar - Speedy Share - upload your files here
Maintenance :: Any Way To Disable Automatic Maintenance In Windows 8
Jul 22, 2013I noticed that automatic maintenance in Win 8 cannot be disabled. I maintain my pc regularly and do not need it. Is there a way to do it or should I let it run?
View 9 Replies View RelatedMaintenance :: Regular Maintenance Scheduled Task Not Waking Computer
Apr 19, 2013Having a problem with the Regular Maintenance waking the computer (Windows 8 on a Lenovo Q-190) to do its scheduled task as it's supposed to do. Here are the symptoms:
1. If I change the time for Scheduled Maintenance in the Action Center (Change Maintenance Settings), it WILL be reflected properly in the Properties of the Regular Maintenance Task in Task Scheduler.
2. However, if I check the box for "Allow scheduled maintenance to wake up my computer at the scheduled time" in the Action Center (Change Maintenance Settings), it WILL NOT reflect in the Properties of the Regular Maintenance Task in Task Schedular. Specially, I check the box to wake up my computer in the Action Center Maintenance Settings, but the corresponding checkmark is NOT reflected ("Wake the computer to run this task"), in the properties of the actual task in Task Scheduler.
3. I then put the checkmark directly in the Regular Maintenance Task itself ("Wake the computer to run this task"). However, at some point in the future, (not right away; I close and then reopen the task to make sure that it 'sticks'), the checkmark "disappears. Then, the task does not run at night while the computer is asleep, but runs in the morning when I wake the computer for regular use. At that point, the checkmark in the task is gone.
Maintenance :: Deleted Maintenance Tasks In Task Scheduler
Oct 15, 2013I deleted maintenance tasks in task scheduler (Microsoft>windows>task scheduler) because I didn't want to have automatic maintenance fire up when I'm working, but sadly... some shit got messed up. My computer starts using hdd at 100% if left idle, and then freezes and all kinds of weird crap that I'm almost positive have to do with me deleting maintenance.
which tasks do I need to re-create in task scheduler in order to have auto-maintenance once again. If you could just read to me all the tasks, triggers, and which programs they are running .
Maintenance :: Recreate Regular And Idle Maintenance Tasks?
Sep 15, 2014I had the idle & regular maintenance tasks disabled but they always re-enabled themselves. In a fit of madness I ended up deleting them but now when I open a folder with videos or images the thumbnails always display in a slow staggered way every time from left to right, If I then exit the folder & go back in they do the same again. It's almost like they are not being cached at all & are having to be redrawn every time.
The only change I have made to my system is remove Comodo firewall & install Private Firewall & delete the idle & regular maintenance tasks.
Maintenance :: Automatic Scheduled Maintenance Is Not Running?
Jun 21, 2014I have Automatic Scheduled Maintenance set to run at 3:00AM. I get to this setting by going to Control Panel > Action Center > Maintenance > Change maintenance settings. I also have the box for "Allow scheduled maintenance to wake up my computer" checked.
However, I note that if I put my computer to sleep for a few days, when I wake it back up, Automatic Scheduled Maintenance has NOT run. I can tell this because my antivirus definitions are out-of-date and haven't been updated since I put the computer to sleep.
how to figure why it's not waking up for Scheduled Maintenance? Is it possibly a BIOS setting? Do I have to manually add it to Task Scheduler? I'm running Windows 8.1 Update 1, ASRock Z87E-ITX mobo, Intel i7-4770S CPU, Samsung 840 EVO mSATA SSD, 16GB RAM.
Maintenance :: Adding Any Task To Automatic Maintenance
Feb 1, 2013I found out how to add a task to the Automatic Maintenance that runs each morning. I use Geekzone's EPG collector to fill in the guide on Media Centre and I though it would be nice for it to run as part of Automatic Maintenance rather than wake the computer up again later to do it's thing.
Here's how:
Create an XML files in notepad and paste this in...
<?xml version="1.0" encoding="UTF-16"?>
<Task version="1.4" xmlns="http://schemas.microsoft.com/windows/2004/02/mit/task">
<RegistrationInfo>
<Date>2013-02-01T19:34:03.9529687</Date>
<Author>johnofe-laptopJohnOfE</Author>
<Description>EPG Loader</Description>
[Code] ....
Save the file then in Task Scheduler, import the XML and it will appear. Edit it from there further if you want.
I got this from exporting a task that runs as part of Automatic Maintenance and edited it to suit.
the thing is, I still don't know how it works! I haven't been able to create a schedules task from scratch that runs as part of Automatic Maintenance.
Other than plagiarising existing tasks to get what I want, how it's really done?
I have what I want, and it works great being able to run all the things I want all at the same time at 3AM each day, as part of Windows' ritual. Even better, if I disable it from waking the computer, everything runs when I'm logged in and Idle. It's fantastic.
Maintenance :: Automatic Maintenance - How To Deactivate Completely
Oct 5, 2013I'm using Intel Rapid Start function, so my PC is starting from completely off to fully desktop in less than 10 seconds (no POST, no Boot ). But I must each time remember to stop "automatic maintenance", because if it is running when closing with IRS, then it won't start again. I can find the setting to change the time of running "automatic maintenance", but I want to deactivate it for ever!! I will maintaine my PC myself.
View 9 Replies View RelatedMaintenance :: PC Not Going To Sleep After Waking Up For Maintenance
Feb 18, 2014I have set up scheduled maintenance on my laptop (on Windows 8.1) as:
I have also set up my laptop to go to sleep after an hour of inactivity:
So far, I have found my laptop not asleep everytime I wake up at around 7AM (two times in a row). Here are some "powercfg" outputs:
What should I do?
When Does Windows 8 Maintenance Run
Sep 14, 2013It's scheduled for 3AM, but the computer is powered down then. Does it run the next time it's powered up and idle?
View 2 Replies View RelatedMaintenance :: Can't Run WEI In Windows 8
Apr 6, 2013I can't run WEI in Windows 8. I've tried to install Media N pack but unfortunately its fail to install!
View 9 Replies View RelatedMaintenance :: Windows 8 100% On Start Up?
May 8, 2013Is it normal to have the disk at 100% on start up? The only program that are even using any of my disk on start up is system and svchost.
View 3 Replies View RelatedMaintenance :: RAM Limit On 64-bit Windows
Jun 2, 2013I have got myself a new laptop recently with the following specs
It's a HP Pavilion G6 2253SA
Intel Core i5 3210M
Intel HD 4000 Graphics up to 1.6GB shared graphic memory
6GB RAM DDR3 at 1600MHz
1TB HDD 5400RPM
Intel HM76 Chipset
Anyway I have a 64 bit copy of Windows 8 Pro installed and this has been re-installed as I did not want to bother with all the Manufacture software that was not necessary for my system
This next part sounds silly and fussy
Anyway even after reinstallation my ram still does not go up to 6GB as it only peaks at 5.89GB and that 103MB is reserved for hardware
I plan on upgrading it to 8GB of ram however I do not want to upgrade it if all the extra memory is just going to be reserved for hardware
Maintenance :: Windows Not Using All RAM Even Though No Limit?
Mar 11, 2013The picture below is a picture of my computers information WHILE rendering a 3D-text object. I will diagnose what each picture seperately with what i want in a brief description in it. What i am also trying to do is render videos but it is wanting take over 24 Hours to rendering a 15 second clip.
(CLICK IMAGE TWICE TO ENLARGE)
The bottom photo is a picture of all my specs and what I am running (Windows 8, 64-bit, 8GB Ram, 2.50GHz, ect, ect. My laptop model is a ASUS R500A with Windows 8 pre-installed, clean. This laptop is a month old and only use it for media).
The picture on the left is a photo of my Task manager while its rendering the video. I can see the CPU is going above its limit even though I have not made any modification to my systems settings but the RAM is not being completely used? It also says 5.1GB Available, 3.0/9.1GB commited? (Even though i only have 8GB), and the Page Pool is low as hell when it should be higher? (If im correct)
The picture on the right is a picture of my virtual memory. I have 8GB of ram but the currently located is 1216MB when it recommends 4.5GB? I was thinking about maybe putting this to 4.5GB but im not sure what to set the Initial Size and the Maximum Size values too.
So basically I want to have my computer modified for rendering at the fastest speed possible. I have also gone into the settings and made sure the limited ram thing is off and it was already off.
UPDATE; I figured if my power options are set to power saving it uses less CPU but when i set it to max it uses all the CPU. This does not fix the RAM problem though.
Maintenance :: Windows 8 Keep Restarting?
Nov 23, 2013yesterday i tried to install a free copy of camtasia 8 the video showed a way so i can register the program free the way suggested was to go to c:/windows/system32/drivers/ect/ then try to change the security properties of the host file and add a states called everyone but isn't work for me so i canceled it, then i get a free user name and serial number from friend and register the program and working properly. I restart may computer lately and its not working , its keep restating i tried refreshing the system but its said my c partition is locked i tried restoring it using troubleshooter but it's not restoring it and tell that no restore point when try to make a one the system response is "system protection is available only in online operating system. auto recovery not working too .
View 4 Replies View RelatedMaintenance :: Setting Up SSD And HDD - Windows 8.1?
Jan 20, 2014setting up ssd and hdd. I have already moved page file on to hdd instead of ssd. What else needs redirecting to hdd. Found a set up guide when installed windows 7 but can't remember what else I did and can't seem to find it now.
View 3 Replies View RelatedMaintenance :: Windows 8 Won't Shut Down
Feb 9, 2013Everything goes as it should, and when computer should shut down, monitor turns off but computer still works (leds on the case, fans and so on).
I don't know what's happening, and why? It's not every time when i shut it down, but it just happens.
I'm using Object dock Start8.
Maintenance :: Want To Multi OS Windows 8?
Sep 1, 2013I want to multi OS my windows 8. Because Microsoft flight X only works on vista, XP and windows 7. So I want to get windows 7 on my PC the easy way. Like installing it with an .exe if possible .
View 2 Replies View Related