Maintenance :: Scanning And Repairing Drive C (chkdsk) Stuck At 100%
Mar 3, 2014
I have been having trouble with my laptop lately. I was trying to install a new driver for my graphics card when my computer suddenly rebooted, I was forced to refresh Windows 8, then an even bigger problem happened, windows kept thinking that it was not registered but when i go to system from the control panel it says it is registered and gives me the product code, so I read somewhere that doing the chkdsk scan will fix this so i did it, first it was stuck 27% for about 4 hours then it is currently stuck at 100%, its been at 100%for about 13 hours now. I do not know what to do, afraid to force restart, might cause errors.
View 7 Replies
ADVERTISEMENT
Dec 28, 2012
I'm having troubles with a disk check.
Firstly, I'd like to mention that I've had this PC for a while... I've even taken the whole thing apart and swapped out all of the components (slowly upgraded over time). It's actually at the stage where I've been left with all the old parts as spares, and put everything back together, almost exactly as it was when I bought it. All in all, the initial build is probably 2 or 3 years old now (for the most part, the specs can be found here).
After formatting the hard drive, putting things together back with the old build, and booting up Windows 8 onto it as a gift for my dad, most things were working fine, but one exe file which I copied across wasn't running (at least one which I noticed). I checked up the error code, found people with similar problems, and heard it could just be that the file was corrupted.
So, to get to the main point... I figured it wouldn't hurt to run a disk check, in case there were any other errors or problems. I knew it would take a while, so I opened command prompt, and typed in "chkdsk C: /r", before hitting enter, letting it schedule the disk check for next startup, rebooting the PC, and then leaving it to do its thing. It's been running probably for about 4 or so hours now, and for most of that time it's been at 27% on "Scanning and repairing drive (C:)". Normally I'd just give in and force shut down at this point, but I'm wondering... what's the best course of action if it doesn't get anywhere with this?
I'd really prefer not to force shut down, in case it causes any errors... I mean to say the least it's taken some effort and persistence to get the old build up and running again.
View 9 Replies
View Related
Sep 15, 2014
I wanted to do a system restore on my Toshiba laptop but when I tried Windows just restarted, gave me error 0x81000204 and told me I should run chkdsk /R. I tried to run chkdsk and everything was going fine and working at a normal speed until it got to 10%, at which point it got stuck and has been at 10% for over two hours. The circle on screen is still spinning so I know my laptop hasn't frozen or anything. I don't really want to have to cancel the disk check because I want to be able to do my system restore, so I was wondering if there's any way to fix this without cancelling, restarting etc. Or if I have to cancel the disk check, how can I do a system restore without doing another disk check and getting stuck again?
View 1 Replies
View Related
Feb 26, 2014
Windows 8 Scanning and Repairing (C:) on Startup - PROBLEM
Laptop model: toshiba satellite l70d-a
Age: 3 months old
Problem: when loading laptop Scanning and Repairing drive C stuck at 100%. I cannot do anything else than removing the battery. Started suddenly. I have tried to see if there were hd problems but found nothing.
I have opened the registry and (following the suggestion from the thread above I have looked at HKEY_LOCAL_MACHINESYSTEMCurrentControlSetControlSession Manager) the reg key is:
autocheck autochk *
And also, since we are talking about the registry, if anything goes wrong how do I reload the registry backup I have just made?
View 3 Replies
View Related
Jul 8, 2014
I have tried to run boot time scan and repair then restarted then the scan started then when it reaches 11% the wheel still turning but stuck at 11%.
View 1 Replies
View Related
May 25, 2014
I have this problem where it takes approximately 5 minutes to boot up my Lenovo Y500 (Windows 8, 64-bit) laptop. I had this laptop for almost an year. It was fine in the beginning, took around 20 seconds to boot. However, over time when I restart my computer because of the windows update or defraging, I noticed that it took extremely long to boot, like 5 minutes. It would be stuck on the Lenovo logo with the spinning circle for 5 minutes.
After that there is no problem getting to my desktop. I assumed my HDD (1 terabyte) had a problem. I ran all different programs to diagnose the HDD but it all said it was in "OK" status. So, I did the chkdsk on the CMD and it prompted me that it'll start when I restart my laptop. So I did and now it's stuck on scanning and repairing drive (C: 27% complete for almost 12 hours.
I am not sure how long I have to wait and if it's going to be 27% forever. I have approximately 250 GB / 1 TB on my HDD. I tried doing recovery but it would not work either. If I tried booting through safe mode, it would continue to do the same thing, Scanning and repairing drive (C 27% complete and stuck there. So finally, I tried going for the recovery USB boot drive since I cannot use the recovery built-in the laptop nor have the recovery disc.
However, I was looking in Google how to make a recovery USB for windows 8 (64-bit) but it all looked like you have to be in Windows 8 in order to make a recovery USB drive, but I am stuck on the Lenovo logo screen. Is there an alternative solution to this? Is there a downloadable recovery drive so I can make it boot to the USB?
View 4 Replies
View Related
Nov 22, 2013
Im using windows 8.1 which came out with my laptop.
Problem is that, that "scanning and repairing drive ( c : )" stuck at 10% completed...
Today I installed latest TuneUp utilities program, and it recomended me to use ' disk doctor' , after that, Ive restarted laptop as it asked, and now all i see is HP logo and that line, where it says ' S. and R. drive C : 10% completed ..
It been like that for a hour or so...
I had did disk scan n repair month ago as well, but then everything worked without any problems. Then (month ago) and now, while this scan and repair is working, I hear some kind of sounds coming out from my laptop. Like clunking,very quiet beepinv or clicking something like that( never heard these sounds, while i boot and use my laptop normaly).
Ive red in this forum about same situation, but didnt got correct answer.
Is there anyway to cancel this scan? I tried holding power button and restarting like that- on boot it goes on s and r. again, and stucks at 10% ..
If no, how long it will take to scan and fix c disk, if it has 1TB in in?
View 3 Replies
View Related
Aug 18, 2014
I recently went to command prompt on my main pc and did : chkdsk /f /r on my main computer.
It said "the current thing is in use, would you like to run check disk on startup? (Y/N) I put Y, then restarted my computer. Then it was stuck on 27% for about an hour, so I got worried and restarted my computer about two or three more times. it says "scanning and repairing drive (C 27% complete)" and none of the times it would load regular windows so I decided to just stick with it.
It's been over 3 hours, and it's still stuck on 27%. How can I disable it or how long will it take?
system info HP desktop
12gb ram
2 tb hard drive
windows 8
Also I tried f8 and it just brings me back to system restore, and when I tried that it just gave me a black screen, so i'm just letting my PC sit and do the C: repair
View 1 Replies
View Related
Apr 20, 2013
I have a problem when booting the widows. It struck while Scanning and Repairing Drive, and I wonder if you have any solution to bypass that.
This problem camp up when i tried to test chkdsk /f /r to restart and check drive.
View 1 Replies
View Related
Feb 4, 2014
My windows 8 HP laptop keeps getting scanning and repairing drive D 100% complete and just stays there and nothing happens. And sometimes it goes on and it just becomes a black screen... My laptop was shut down for a few weeks and this happened and I need it again now... I got a new laptop which is why it stayed off but now i need it again. What should I do? I don't care if everything on it gets erased. I actually prefer to format it. Moreover, my f keys dont work nor does my escape button.
View 4 Replies
View Related
Jul 10, 2014
I have a Samsung Ativ Book 4 (model number: np470r5e-k01ub). When I turned on my laptop today, I was prompted the message "scanning and repairing drive c". This has been going on for longer than I expected (about 6 hours and is stuck at 9%) and I am starting to get worried that something is seriously wrong. I have tried rebooting into safe mode but my keyboard isn't working. I have no way (that I know of) to restore to factory settings seeing as how my keyboard isn't working.
View 1 Replies
View Related
Jul 13, 2014
Every time I boot up my windows 8 laptop now, it just says Scanning and Repairing drive C and then it gets stuck at 27% and never moves past that
View 3 Replies
View Related
Apr 3, 2013
So, long story short I had some YouTube uploading troubles, I asked some guy about it and he said its possibly caused by a virus, so I looked at my antivirus and it said there was an error with my C drive and I needed to restart to repair it, so I did and the repair process got stuck at 27% for about half an hour, I've tried everything and I've looked everywhere, but I got nothing, my laptop now can't do anything, if I try to skip the repairing process it just restarts it again so I can't get anywhere with it, it's a new computer
View 1 Replies
View Related
Jul 19, 2013
I`ve got HP Envy Phoenix H9-1400ec with Windows 8 64bit. Can`t boot it, I`ve tried restarting and all that during the scanning and repairing process, but it`s just frozen on 1% for quite a few hours already(I just let it run in case some miracle happens...)
View 8 Replies
View Related
Sep 22, 2012
I have windows 8 on my computer. Yesterday I turned on my laptop and it says scanning and repairing drive but it keeps getting stuck on 28%. I can't install windows 7 again because you need to get past the start up screen, which I can't.
View 9 Replies
View Related
Nov 7, 2013
i recently got a new laptop "asus vivobook" that came preloaded with windows 8.
The laptop comes with a hybrid 24 GB ssd (8GB of those are for the system files,windows 8 is installed on,the remaining are in a 2nd partition for recovery) i deleted the recovery partition and made a recovery on an 8 GB usb drive,because im dual booting a different linux os alongside windows.
I used rEFInd boot manager to boot the 2 operating systems,everything boot and works fine.
However,since the dual booting started i noticed that the windows 8 loading time has became a bit slower,when i choose to sart windows 8 the asus logo appears and under it this message
"Scanning and repairing volume (?Volume{...large hex identifier..}): 100% Complete"
it stays for 2,3 seconds and then windows 8 start,i ran a chkdsk for the c drive,but that didnt solve the problem.
View 9 Replies
View Related
Dec 8, 2012
I downloaded and installed Windows 8 on October 26th. So far, great experience however... the last couple of days when starting my new Dell Inspiron 5720 it is running a "Scanning and Repairing (C) and is getting stuck at 27% (waited over 2 hours) so I hold down the power button and it restarts as normal. Only seems to start the check on every 2nd or 3rd startup. I have googled and read many articles and have since error checked my C: drive through properties with no errors being reported.
I guess my question is what would cause this to all of a sudden start and why and how do I stop it. It is very frustrating . I have completed virus scans, defrag, error checking, etc.
The Dell laptop is new but came with Windows 7 in early October. It is 8GB RAM with a 1TB drive running Intel 7.
View 9 Replies
View Related
Jul 24, 2014
in the process of trying to fix another issue (metro games not working on one profile but working on another) I tried to scan and repair any drive errors, it gets to 58-59% and then the machine just reboots Running Windows 8.1 pro 64-bit
View 2 Replies
View Related
Feb 24, 2014
I have some questions regarding the new Chkdsk in Windows 8 (I'm using Windows 8.1 Pro 64bit).
note that Windows 8's Chkdsk has changed considerably since the previous Windows versions; so if you know about the Chkdsk in Windows 7 or previous Windows versions, this could not apply to the Chkdsk in Windows 8.
I also point out that I'm talking about the GUI version, accessible from the drive's properties Window.
My main questions are: when Chkdsk has finished scanning, and the results window appears, can I at once proceed with the following, or should I wait some time:
1) In case of an external USB drive, disconnect the hard drive (with "safely remove hardware", even if the cache is turned off), and turn it off.
2) In case of an internal drive (HDD or SSD), reboot Windows, or turn off the computer.
My worry is that if I would disconnect a USB drive, or reboot or turn off the PC in case of an internal drive, before the Chkdsk-related activity is finished, then the file-system of the disk in question could get damaged.
My doubts come from the following facts:
- I have been told that when the Chkdsk results window appears, this means that Chkdsk has finished working with that drive; but I have noticed that some short drive activity is happening some seconds (about 6) after the results window appears (should be a write activity, not sure if also read activity). I noticed this by observing the LED on my USB drives, and also by monitoring the drives in question with Windows 8's new Taskmanager.
- In case of disconnecting USB drives, I have been told that I can be sure that if some drive activity is happening, then the "safely remove hardware" feature won't have effect, and would warn me that there is disk access going on; but I have tried to select "safely remove hardware" while Chkdsk was in the middle of a scan, and the result was that Chkdsk got interrupted (with an error messsage appearing probably from Chkdsk), and the USB hard drive got removed. Though this seems not to have caused any file-system errors (I did another Chkdsk scan later).
You may think that I just need to look at the drive's LED, or monitor the drive's activity with the new Taskmanager, and take note of after how much time the drive activity ceases. Then I would just need to wait so long before disconnecting the USB drive, or rebooting or turning off the PC.
My problem here is that I'm not sure if the new Taskmanager, or the drive's LED, are sensible enough to detect even the smallest disk access, which could get unnoticed. I'm not sure how much I should wait... seconds? Minutes? What do you think? Perhaps there's no need to wait at all?
I did some tests by disconnecting (with "safely remove hardware") a USB drive shortly after doing a Chkdsk on it. Then I did another Chkdsk after turning it on again. I didn't get any error message from Chkdsk. But I'm still worried that there could be an unfortunate moment, during which a disconnection (still with "safely remove hardware") could cause problems, perhaps because in that moment a write operation could be in process.
I think I have read that the new Chkdsk in Windows 8 uses VSS ("Shadow Copy") to check the drives while keeping them online. With this new Chkdsk, I think it is possible to continue using the drive while the scan is happening, even on the system drive.
I was thinking about this: is it possible that the short activity which I have noticed after Chkdsk's results window appears, comes from this Shadow Copy Service, which is "unmounting" (?) the shadow copy used by Chkdsk?
If this is true, is it important to let the "unmounting" task happen, or can I disconnect, reboot, or turn off before it starts? And what happens if I interrupt this "unmounting" task in the middle, while it is in process?
Does it make some sense to wait some time after doing a Chkdsk, or can I at once proceed to disconnect the USB drive, or reboot or turn off the PC (in case of internal drives)?
View 1 Replies
View Related
Dec 9, 2013
Today I got an IO error when trying to upload a song to a music site. After doing research it said to run a test on command. Once I restarted my laptop it stated scanning and tunnibg. My computer went to safe mode but would not come out if it. I had no choice but to press down the power button. I tied it back on and it ran again. After 10mintues it went to 27% and stayed there for an hour. Now it went to sleep mode again. I don't know what yo do. I can't stare at the computer for ever to keep it from not going to sleep mode. My laptop is a year old and is an HP.
View 1 Replies
View Related
Jan 16, 2014
After I get to the event viewer, where do I go from there?
View 2 Replies
View Related
Apr 25, 2013
I have read that Windows 8 has a new Chkdsk, which checks the file-system integrity in background. I'm using Windows 8 Pro 64bit (and NTFS file-system on all drives).
Does this improved Chkdsk check the file-system just when the computer is not used, or does it check it also while the user is working? Or does it scan the drives just when it's maintenance time?
Does it still make sense to run a manual Chkdsk on some occasions, or can I just not worry and let Chkdsk do its checks automatically? Such occasions would be for example after the computer completely hangs and I have it to brutally turn it off with the power switch (happened lately with a Linux live-CD), or after problems with the electric line (loss of power/power outage, resulting in instant turning-off).
In other words, is it useful to run a manual Chkdsk when there is a suspect that something could have gone wrong with the file-system, or can I just continue working and let Chkdsk do its verifications?
How long should it take (more or less) from when a file-system corruption arises, to when it gets detected by Chkdsk?
What worries me, is that not doing a Chkdsk at once, to repair eventual problems, may make the problems get bigger while the hard disk (or SSD) gets used. And they could get such big that they could not get repaired anymore (just an hypothesis).
View 2 Replies
View Related
May 23, 2013
I have a dual boot laptop with Windows 8 and Win7. When I choose to run chkdsk /f from Command Prompt(Admin) on my Windows 8 boot drive, I get the normal message that says disk is in use and to type "Y" to schedule it to run on restart. I type "Y" and hit "Enter", but if I either Restart or Shutdown and turn laptop back on, and choose to boot Windows 8, chkdsk seems to cancel itself. I get the message to "press any key" in 2 seconds if I want to cancel the disk check, but I never press or do anything yet chkdsk seems to cancel itself. When Windows 8 boots I have looked in Event Viewer and there is no sign of any chkdsk or wininit event that says it checked disk for errors.
I have gotten the message in Action Center, to reboot to scan and repair errors which works fine. Right clicking my boot drive, going to the Tools tab and scanning drive for errors also works. My only issue is scheduling to check my boot partition for errors via command prompt.
Must I disable Fast Startup/Hybrid Boot for the scheduled chkdsk to work or something else?
View 6 Replies
View Related
Jun 13, 2014
Today I've tried doing a Chkdsk scan on my primary drive. Through the console, I entered this line to start the process on a re-boot 'chkdsk /f /r c:'.
I afterwards left it to do it's work for the next 1 and half hours '6:40-8:10pm', during this time I went to check on the progress of the scan and what I saw was that it was only '10%' into completion, this confused me greatly as previous computers that I have owned would atleast be around 70, or 80% percent completed, so not knowing what to do, I did a cold-boot.
From what I can tell, no visible damage has afflicted said the drive I did the chkdsk scan process on, but I would still very much like to know why my scan is hanging.
View 9 Replies
View Related
Apr 8, 2014
Delay Chkdsk start up time at OS Boot | Windows 8 & 8.1 (Or Disable Altogether)
Previous to Windows 8 if Chkdsk needed to run without prompt the user had the ability to cancel if so desired. Since Windows 8, the user input has been removed.
At the least, you can change the delay setting as follows:
Modify DWORD "AutoChkTimeout"
IMAGE ONE:
1. Open Regedit:
One way to open regedit is to hit the Winkey+S and type regedit, hit enter when you see it appear.
2. Navigate to the following registry key:
Code: HKEY_LOCAL_MACHINESYSTEMCurrentControlSetControlSession Manager 3. Click on the folder "Session Manager"
4. In the right hand pane you will see registry values. Right click on the value "AutoChkTimeout" and select "Modify" (See image one)
If the value is missing, create it (See image two)
5. Change the "Value data:" to the desired delay time of your choice.
e.x. Changing the value to 10, will delay the Chkdsk start time by 10 seconds.
Click OK, close the registry.
Finished.
Create DWORD "AutoChkTimeout"
IMAGE TWO:
If the registry value "AutoChkTimeout" is not present:
Right click on an empty space in the right hand pain (in folder "Session Manager")
Select "New"
Select "DWORD (32-Bit) Value
Name it "AutoChkTimeout" (No Quotation Marks "")
Follow step 4. above.
Remember:
Name = AutoChkTimeout
Base = Hexadecimal
Value Data = Delaytime (in seconds)
DISABLE automatic repair in Windows 8 & Windows 8.1
If you would like to disable automatic repair altogether:
1. Open the command prompt as Administrator (an elevated instance). If you have no idea how to open an elevated command prompt. Hit Winkey+S type in cmd.exe, when it appears, right click on the name and choose "Run as administrator"
2. Type the following text into the cmd window
Code: bcdedit /set recoveryenabled NO
You have now disabled the Automatic repair function.
To reinable: Follow step 1 and in step 2 type in the following text:
Code: bcdedit /set recoveryenabled YES
Having disabled the Automatic repair feature, you can follow Brink's tutorial on manually running Chkdsk > Here:
CHKDSK - Check a Drive for Errors in Windows 8
View 3 Replies
View Related
Mar 24, 2014
I was running my pc with Windows 8.0 Pro 64 bit and I now getting a screen with the Windows logo and I am now getting a message "Diagnosing PC & Auto repairing disk errors may take several hours".
It has been like that for a couple of hours.
How long I should leave it running or perhaps I should do a fresh reinstall of Windows, I have the Microsoft DVDs?
View 2 Replies
View Related
Mar 4, 2013
Since a couple of weeks, Windows has started scanning my disk on every boot. It does 1%, 2%, then sits for a while before it jumps to 9%. Then it works itself up to 43%, where it sits for a long while before jumping to 100%. Every time. I'm not having any problems with the system, and I'm not missing any files as far as I know. Why is it doing this and how can I get rid of it?
View 1 Replies
View Related
Jun 8, 2013
I am dual booting Windows 8 and win7. I actually have Windows 8 installed on its own hard drive and win 7 installed in its own hard drive. The win7 hard drive has been in use for the past 2 years and I have had Windows 8 running for about a week now. I purchased another hard drive for Windows 8 and left the old Win7 as it was.
I also have 3 other hard drives in the system. Everything is formatted NTFS.
So my system is as follows
Drive C - Boot Drive - I physically swap out the dedicated hard drive for Win 8 or Win 7
Drive D - internal 250 GB sata drive
Drive F - internal 250 GB sata drive
Drive H - internal 250 GB hard drive.
I have been running this config for about 2 years under Win7 with no problems.
The problem that I have now is when I swap the boot drive and boot up a different OS than last time (Like booting Windows 8, powering down system, swap boot drive, boot Win7) the system always says that there are problems on the 3 non-boot drives. It runs chkdsk(it least that is what it look like) and processes the 3 non boot disks one at a time which take about 10-12 minutes for all 3. Most of the time it finds no problems, but about 1 out of 5 boots will find a problem with one of the disks and then fixes it. The disks seem to be OK while I am running. I then power down and swap boot drive and reboot the other os and we start all over again. I am powering the system completely down for each reboot to make sure that the disk cache is flushed.So far the disk problems have been fixed by chkdsk at boot, but I am sure the day will come when the disk cannot be fixed and I will loose data.
View 3 Replies
View Related
Aug 16, 2014
I have a HP Pavillion Sleekbook 15-b002ee with Third generation core i5 processor 1.7 GHz, 500 GB Hard disk and 4 GB of RAM installed. Windows 8 came pre installed on it.
I bought this laptop 11 months ago and it worked fine for 10 months and then from the last month its presenting unusual problems. My disk usage is stuck at 100% and the laptop freezes and never lets me work or do anything. Heres what i have already done to solve the issue but have been unsuccessful:
1) I have reset my PC completely and reinstalled windows 8 using the factory setup. Didnt solve the issue, newly installed windows displays the disk usage 100% and the performance is same i.e the system freezes.
2) I have tried adjusting my paging file, no change made a difference to the performance of my laptop. The default system managed Paging file size is something around 3.89 Gb. Does my problem have anything to do with my paging file?
3) disabling the "Windows Search" and "Superfetch" services and still it didnt solve the problem.
4) I have also run checkdisk on my hard drive completely. It took me a complete day to do so but still no change.
5) Before resetting my laptop, an error called "Kernel_data_inpage(http.sys)" used to come on my upgraded windows 8.1. Whats the issue?
So what should i do? Is there any problem with my hardware? Is my hard drive having bad sectors and is that causing the problem?
View 1 Replies
View Related
Jul 31, 2013
I have a Toshiba laptop, it's less then a year old and came with Windows 8 pre-installed, so i don't have a disc. Last night i was watching a movie on it when it froze up, i had no choice but to force reboot as it was unresponsive but when it rebooted it when straight to diagnosing and attempting repairs! I left it over night to allow it to repair but it never made it past that screen.
It's less then a year old and it hadn't had a single issue up until last night? I've tried rebooting to watch for options watch for booting options but it doesn't give me any choices at all just goes straight to Diagnosing and attempting repairs!
View 3 Replies
View Related
Apr 24, 2014
I was playing WOW the other night on my month old PC and all of a sudden I got a full red screen. I restarted the comp and this auto repair screen popped up and it freezes and just same thing over and over. the bottom of the screen is cut off and the only other window i can get into is the bios setup utility window. Cant get into any kind of safe mode nothing.
my computer is an Gateway SX2370-UR12
View 1 Replies
View Related
