Ping Virtual OS From The Host And From Another Network?
Nov 8, 2012
I have three virtual OS (windows 2003)installed on my server (window 2008), I can ping it from within the network but I cannot reach it from outside the network. However, I can reach the host and any other physical pc from outside the network.
I also installed VMware 5.0 on my laptop running window 7. Windows XP is on the VW. it can ping the host but the host cannot ping it. I have set it to bridge but it is still not the host cannot still ping the OS on the VM.
I have done as you instructed. The WinXP VPC I set up can see the internet but for some reason it does not see the host Windows 7 machine. When I ping the host from the VPC I get no response. I can ping the VPC from the host machine. I intend to run the ArcInfo license of ArcGIS Desktop on the VPC. That license requires communication with a license server. The license server is running on my host machine. If I can't ping the host then I won't be able to use the license server.
I have done this on another machine with WinXP as both the host machine and the VPC and the VPC can see the host via ping.
I have an XP virtual machine running on a 64-bit Win 7 host. I have a home wireless network that I need to access from the XP VM in order to use printers attached to the other computers on the network. All computers currently on the network have the same workgroup name. I have networking on the VM set to use the wireless adapter on the host laptop. With this configuration I can see and access the host, but I cannot see nor access any other computers on the network.
Now, it seems to me that I will need to run the XP Network Wizard to set up the network on the VM before I am able to see the network, but after reading dozens of articles and posts on networking a VM, I have never seen this step mentioned. (I am at work now, so I can't test this out on my network until later.) So, my questions are:
(1) Do I need to run the XP Network wizard to get the VM to join the wireless network, and (2) if I don't need to run the wizard, what DO I need to do to get this to work?
I've taken on a migration project for an SMB. They have an ancient application that they use and cannot find a replacement for.
The problem is that the application writes to the root of C: when creating mail merge documents, while this wasn't an issue on XP with the correct permissions its a problem with 7 due to UAC not letting standard users write to that location.
The software vendors have come back with the standard answer "turn UAC off" ... nope .. not prepared to do that.
I've managed to get a copy of the application so I could do some experimenting with Virtual XP mode. While this allows the application to run and create the mail merges correctly it seems to require the creation and setup of a VM every time a new users logs on.
Is there anyway to share a single VM between multiple users or could it be done by assigning published applications to all users on the host?
I'm running windows 7 ultimate and i haven't run XP mode in a while so i'm not sure if it was an update or what that caused this. but the crashes that i'm referencing happened on 4/27/2012
i have v-box running on win 7 in the vbox i have win xp i have it set on bridge connection i can ping the windows 7 side just fine but i can't ping 8.8.8.8 google and have no internet connection the internet on the host is fine?
the router gateway address is 192.168.178.1 the windows host has a static ip of 192.168.178.107 the xp in the v-box can not connect with dhcp so i have it set manual to ip 192.268.178.107 subnet 255.255.255.0 default gateway 192.168.178.1 dns 1 : 192.168.178.1 dns 2 : 8.8.8.8 it is bridged with a wireless network guest additions are installed
I have a PC desktop Windows 7 ultimate 64bit and Dell Vostro 3500 Windows 7 professional 64bit. Both connected through D-Link 655 router and they are in same WORKGROUP with files and printer sharing enable. As security the PC has Malwarebytes Anti-Malwares, Comodo firewall, Avira free antivirus. The Vostro has Zonealarm firewall and Avast for anti-virus.Recently I bought a NAS (Synology DS211J) in order to centralize important documents, media files and the printer. My desktop Windows 7 ultimate has no problem connecting to the NAS. I can ping the NAS ip and name. I can see the NAS listed in network from windows explorer connect to it and browse the NAS directories...yes flawless! However the Dell 3500 could ping the NAS ip and name but I do not see the NAS in the laptop Network of Windows Explorer therefore I could not access the NAS and browse the directories. Both PC and Vostro could ping each other ip and name, both are listed in their respective Network of Windows Explorer and I could access to each other shared folders. For debugging I turned all securities softwares down on both PC . Problem still persist i.e. Vostro can ping NAS but do not see it in network. I have another laptop winXP Home edition 32bit and I could ping both PC and the NAS by their ip and names. I could access from that laptop the shared folders of the PC Windows 7 ultimate and NAS but not the Vostro. Vostro can ping ip and name of laptop winXP but not listed on his network places.
why the Vostro 3500 can ping the other machines by ip and name but it does not listed them in the network windows? Is it because of a Windows service not enable, a setting or something in the registry?
There's a program I use (Pocket Informant iPhone Outlook Sync) which requires that my PC and iPhone be on the same network in order to sync.
The problem is that it works only when using my home network. When I'm at home, from my PC I am able to successfully ping my iPhone, which is connected to my WiFi network. This works whether myh PC is also ethernet-connected or WiFi-connected.
When I travel, however, even though I successfully connect to the WiFi network on my iPhone and PC, I am unable to ping my iPhone.
I have tried disabling the Windows Firewall and I get the same result!
I can't believe that all these different WiFi networks I connect to (airport, hotel, work) that they all have a configuration issue, so I'm thinking that the reason for the discrepancy must be because of some setting/configuration on my PC/home network.
Is there anyhing else besides disabling the Windows Firewall that I can try?
I am using Foxpro 2.6a application files they work perfectly on all 32 bit systems XP Vista Windows 7 and the screen displays work fine in the program and display correctly. When I use Windows Virtual PC hosting Windows XP the Foxpro screen Data runs off the page now missing 3 rows of data.I have complete control over the Desktop resolution but that does not help, windowed mode or full screen does not help.
Last Friday my main desktop crashed (lost power to the machine) and on restarting the PC was unable to "identify" the network. By identify, I mean, when using "Network and Sharing Centre" on the basic network information page, the PC shows "Identifying" under "active networks" - no matter how long I leave the PC.
PC details Model: Packard Bell Power x-30 Processor i7 870 @2.93GHz RAM: 8GB O/S: Windows 7 Home Premium (64-bit)
The main desktop is connected to the modem router (via Ethernet). The modem router is showing no sign of any problems itself, all the dashboard lights look ok (i.e. power is on, port 1 shows the Ethernet connection in place, both wireless bands are lit, the DSL is lit and so is the internet). The household contains a number of laptops which continue to work ok wirelessly and/or wired through Ethernet. Even mobile phones are accessing the wi-fi ok.
The DNS Server address looks ok, as that is the address of the web page to the router. I cannot access that web page (address) via the main desktop, but I can from other devices ok. Having gone through Device Manager the Realtek PCIe GBE Family Controller is showing as "working properly". I have tried pinging the DNS Server address, and that fail. I have gone through a system restore to a previous point (before the day of the crash) but that seems to have made no difference either.
I have attempted to set the IP addresses (for TCP/IPv4) directly IP address 192.168.0.3 Subnet mask: 255.255.255.0 Default Gateway: 192.168.0.1 And therefore forced to set the DNS Server address too Preferred DNS server: 192.68.0.1
But I don't know what to set for the alternate DNS Server, so left blank. This seems to step me forward, in that the device/network is now identified. However the internet access is still not work, as the "DNS Server is not responding".
I have a W7 Home Edition 64 bit and by mistake installed an old piece of hardware which over wrote my Network USB Host Controller driver. I have a disk image backup from before; I just need the name of the driver so I can install the correct one.
Win7 as a host for VPC - Network card not recognized. I've just installed VPC over Windows 7 7077 but on the network settings I cant choose my LAN connection, I only have the option of Shared NAT?
Is there any problem reported regarding this subject?
I have just installed Windows 7 32 bit on a computer with is hosting a HP Laserjet 1600 printer to which I would like to print to from my laptop running Windows 64 bit. I have added the network printer from the host machine but it won't print. Both systems File and Printer sharing is turned on in the advance sharing settings for both computers and I can share files OK. I have also allow Print permissions in the Security tab under the networked printer properties. However the spooled document print when I restart the Host computer?
I have recently installed a network printer and had many problems. I've changed the IP address 3 times to resolve and still cannot. When I do a continuous ping to the printer (approximately 100, I had 4 request time outs). The 4/5 clients using the printer are having problems printing to it.
I recently purchased a desktop computer with Windows 7 already installed. I set up my wireless connection to my home's wireless network, but when I first connect to the internet, it connects to a virtual profile instead of my wireless network. I've tried setting my wireless network as the default network, but after I shut down and restart, it just goes directly to the Virtual Profile. I've even tried deleting the VP, but the computer finds it and goes straight to it as soon as the computer starts up again. Is there any way to permanently disable the virtual profile?
I have several VPNs and Virtualizing software installed, and they have this virtual network adapters in the network and sharing centre. In the "connect to a network menu", one shows working internet connection, while the other one shows no internet access, How do I get rid of those entries? I dont mind messing with the registry or the system files.
my girlfriends pc at her university blocks certain ports which are required by a website which she uses to watch tv online. Therefore as a work around, she bought a service which offered a VPN. This meant that she on her uni pc be connected to the uni internet, however then open a VPN connection which meant she would then be connected to this VPN and browse the internet through them whom do no block ports.
My question is could someone please advise me on how to do this, I have WIndows 7 and she has XP Pro. I tried setting up my pc as a host, allocating her a username and password and allowing incoming connections etc. however upon trying to get hers to connect to me, it just timed out and could not connect!
I would appreciate if someone could give me a step by step guide on how to set up my PC as the host and her PC as the client, in order for her to browse the internet using my internet, not her universities. I don't want remote desktop as dont want her having control and seing my desktop, just sharing my internet.
I need to add a virtual Network Adapter (Microsoft Loopback Adapter), but all I can do is to get to a "waiting for connected devices" dialogue... Is there any way to manually add some device in Windows 7?
Running Windows 7 RC 64-bit. Everything working fine within Windows XP Mode. All of the network and network devices are visible. All systems have same user account and password. Network is workgroup called WORKGROUP.
Per the instructions, I uninstalled the previous versions of Windows Virtual PC and Windows XP Mode, downloaded and installed the new RC versions of these products. Everything installed fine, but within the XP virtual machine I do not have access to any of the other resources on the my network. Previously they were all visible.
I went though the normal XP network set up, but the only thing that is visible within XP is the XP machine itself. My network is a simple non-domain network named WORKGROUP. What do I have to do within the Windows XP Mode virtual machine to see the printers and other systems on the network.
I have over 50 virtual networking adapters in device manager, I have posted this question in many forums, and still cannot get rid of these pesky unused extra adapters. I know they have been created by using Virtualbox, and by creating many virtual machines and updating virtualbox. Unfortunately, I have tried uninstalling virtualbox and the drivers all remain in devicemanager. DeviceMgmt also does not allow me to uninstall or delete the adapters, (When I do they just stay there, even after rebooting.)I most likely have to go into the registry and delete them, but they are in so many different places there, I need to know the correct place to delete them. I have a bet that this is the forum where I will get the answer for this even though I have posted in virtualbox forums, technet, MSDN, superuser, serverfault, and stackoverflow.
I am looking at a solution to tap into the portability of virtualization across hardware. i.e. if I have my development environment as a VM, I can access it and bring it up from any machine on the network. This will enable me to be not attached to any physical machine and allow me to access my development machine seamlessly from anywhere if it is stored in a network location. I have mainly two questions around such a setup.
1) Is there anyway of hosting the VM without incurring the expense of both the host operating system and the guest operating system? The only functionality of the host operating system to host the VM.
2) Is it viable from a performance stand point to have a VM booted up on a machine from a vhd placed at a network location?
I upgraded to Windows 7, but I have a few software I installed on Virtual PC 2007 before. I use XP mode but can't find a way to use the virtual HD created with Virtual PC 2007. Is there a way to convert the virtual HD so that XP mode can recognize?
Got a new Windows 7 Enterprise 64 bit machine, found that it did not come with virtual PC. Downloaded the critical patch Windows6.1-KB958559-x64-RefreshPkg.msu and installed it. Windows Virtual PC shows up in my Start Menu. Good so far. I go through the steps to create a virtual machine and use the option to 'use an existing vhd file' and when I click 'Create' I get the above pop-up message "Cannot attach the virtual hard disk to the virtual machine. Check values and try again". A factual message but completely useless as with all error messages from Microsoft. I have tried the following:1. When I attach that vhd using Disk Management, it mounts in drive E:, I can see the files and browse the dirs in E:. In the Disk Management View, the drive shows up as 127 Gigs but 107 is unallocated space. The physical size of the vhd is only 25 Gigs2. Others in my company were able to create the virtual machine with the same vhd, checked the byte size and timing, so nothing is wrong with the vhd file itself.
3. Tried to create after shutting down all virus protection including the Micorsoft antimalware protection service. No luck4. Tried Vhd resize to resize the vhd to a smaller size (since it showed up in disk management as 127 Gigs, I thought maybe it was that size), but VHDResizer could not open the input file, gave an errors "Can only load fixed or dynamic drives"
Ping does not go through to one of the Windows 7 machines on my home network but there is no problem accessing from other Windows 7 machine to this machine for file sharing.