the title say my problem is with pfn_list_corrupt and memory_management have already reinstalled windows thinking that was something bad with filesystem , but I still have this problem! Then i thought rams were broken , but after 8 hours i got 0 errors. And they are random , if i m play bsod , if the pc is idle BSOD.
[code]...
I've recently began building my first custom-built computer, I began with an old Compaq Presario that a friend gave me, and I've pretty much gutted it and replaced all its components. The components I've replaced have included the motherboard, processor, hard drive, RAM and PSU (I'll include the specifics of my set-up below). I've been trying to install Windows 7 but have been getting the blue screen (BSOD) before the installation could complete. The BSOD said "PFN_LIST_CORRUPT" towards the top of the screen. I'm fairly sure that I've installed all the new hardware correctly. The following is the new hardware I've installed:
Processor - AMD Phenom II (3.2 GHz)
Motherboard - Ultra Durable 3 (GA-880GM-UD2H)
Hard Drive - Hitachi Deckstar 7K1000.C (1TB SATA)
RAM - Corsair 2 Gigs (2 sticks, 4 Gig total)
PSU - Logisys PS550ABK (550 Watts)
Last week i brought to your attention i was having dxdiag and atikmpag errors. I have resolved that by purchasing and using a Nvdia gtx560ti and the tech support people i bought the previous 6950 from advised me that they have come across a lot of problems with the Asus version of the card.With the new Gtx560ti, i purchased another 4GB of the Kingston HyperX pnp Ram. Since, i was getting random BSODs relating to "page fault in non pages area". I resolved this by removing the ram stick in Slot 4 of my Motherboard. After a few successful attempts, i reconnected the "suspected" Ram stick in Slot 3 and put another stick in Slot 4Since, i have not had a problem with page fault in nonpages area BSODs.
However, i am now beginning to get PFN_LIST_CORRUPT. What i would like to know is if this is related to the "bad" ram stick or a driver problem. I use the Uniblue Driver Scanner which is unable to find any outdated drivers. Can you look at Note that i used the Windows 7 memory diagnostic test and a pfn list corrupt BSOD occurred at 99% completed.At 98% it still showed "no errors have been found".
I got a windows 7 PC six months ago, and ever since have been getting random BSOD's mostly when web browsing or leaving my computer on while it is not in use. Their are no issues when playing games, strangely enough. So far I have replaced themotherboard, ran a disk check and got no errors, ran a SFC scan and got no errorsand ran the Memory Diagnostic Tool with no errors. I'm completely stumped as to what may be causing this. All of my drivers are up to date and I have service pack 1 installed. I am not overclocking[CODE]
View 2 Replies View Relatedi just have a assignment to explore the memory management of win 7
i have a problem to find some resource about this case, because win 7 is a new OS,.
and i got some information that win 7 was using a new method of memory management that different with the past version of windows OS and make it work faster..
i very hardly to find what memory management method was used in this OS (win 7),..
can u help me to describe or give me some information to find about the new method of memory management in win 7...?
I've been using Windows 7 now since 6th of May, and love it! I haven't had any troubles except 2, but this topic is meant for only one.
I remembered an application called Everest, it lists all of your hardware and information about it, OS and stuff, really nice. It also has tab for sensors, where you can monitor temperature.
When i was looking around in Everest, I found out somehow 7gigs. of virtual memory is available, and most of the time somewhere around 2gig. is being used. That was kind of weird, because I have 4 gigs of RAM, and most of the time only 25% is used of it. So, why would Windows prefer use of the virtual memory over the use of physical memory? I found out virtual memory could be managed in "advanced system settings". because 2.5 gigs of virtual memory was used most of the time, I thought: why not just completely disable paging file.
So it's: computer --> right click properties --> advanced system settings --> advanced tab --> performance --> settings --> virtual memory --> change.
So finally comes the problem, I have successfully disabled the paging file, and it says "total paging size for all drives: 0 mb". But when I go to Everest, it still says I have 7 gigs of Virtual Memory available, and it uses 2 gigs. I want to make full use of my physical memory!
Getting several BSoD a day and it driving me mad! I have replaced the RAM but still giving me the "fault in non paged area" error and i have reinstalled windows and the error still there
i have a pile of memdumps if someone can help me
BSoD error i have had "IRQ", "MEMORYMAGEMENT" and "NON PAGE FAULT",
with me replacing the ram and reinstalling windows, where else could cause this issue?
I'm new to this community and not the most computer savvy person, but I've been having this error for a while and it's starting to bug me. We recently got a new computer but as I start to use it, I'm noticing a lot of crashes and blue screen. Of the errors I've noted, the major one seems to be the "MEMORY_MANAGEMENT" blue screen. I'm currently running Windows 7 64-bit and I have about 16G of memory installed.I did some preliminary research and many topics suggested either pulling sticks out (which I do not know how to do), posting minidump file (attached), and running a memory test (I just ran it for 12+ hours and it still did not finish, but I need to use my computer).
View 5 Replies View RelatedAfter previously solving the BSOD error "a clock interrupt was not received on a secondary processor within the allocated time interval" by replacing the CPU, I have run into another BSOD. This time the error is "memory management". After doing some research I'm thinking this error is about some program conflicts or something similar (I'm hoping that is the case!), instead of a hardware problem. I have attached the last 3 minidumps I have.
View 14 Replies View RelatedI started to get random BSODs, usually after a few hours after turning on my PC. The only major change I made was a firmware upgrade to my Asus P8Z68-V Pro MB to the latest iteration: 3203 released Feb 21/12. Recently my website got hacked via ftp password breach but I ran a full system AV & Malware scan and results were clean.
Windows 7 64-bit (student upgrade version), approx 8 months old.
System: Intel i5 2500k cpu @ stock, 8800GT, 16GB G.Skill PC3-12800 ddr3 ram,
Windows booting off a WD 1.5gb Black HDD
[code] I bought this computer at Microcenter, they manufacture them and sell them under the brand PowerSpec. Mine is the B633 Since I bought it, it had had multiple errors, as shown in the attached .zip. I want to know what I need to do to fix these errors.I have ran memtest and let it do 10 passes with 0 errors. I am running driver verifier right now and have had 2 BSOD that I have never seen before, one was Special Pool...? Most of the time it is Memory Management BSOD, however.
View 7 Replies View Relatedmy computer has been receiving random BSODs throughout the day, especially when I am browsing the web. The message is usually "memory management." This computer is around 3 months old. The first 1 1/2 month, it did not experience this problem. However, from July and onwards, my computer would get BSOD; it would occur at least once a day.
According to BlueScreenView, the driver that is causing BSOD is "ntoskrnl.exe."
I just installed windows 7 rtm 64bit and I really love it. But i got a performance problem under certain circumstances and hope u can help me
First, here is a list of my relevant hardware:
AMD X2 4200+ @2.7 GHz
3 GB DDR RAM
System drive: 2 x 250 GB (raid 0, about 90 MB/sec reading)
graphics: 9800gt
2 USB Flash drives dedicated to Ready Boost (2 GB and 512 MB)
Now let me describe my problem: I have to run 10 virtual machines on this PC. I use VMWare Server, each virtual machine is set to 128 MB RAM (lowest value possible, any lower values result in excessive swapping). All virtual machines are set up on another harddrive (200 GB, about 40 MB/sec reading), so they don't affect my system drive.
Performance is normally just fine in Win 7 (the virtual machines eat up very little CPU power). But when i use very demanding applications, e.g. Crysis, performance becomes a nightmare (framedrops, game is not playable). The LEDs for my flashdrives and my harddrive are flashing all the time. I guess all my Ram is used and win 7 swaps the data needed for crysis instead of swapping my virtual machines. Only way to play crysis is to stop my virtual machines (which is not acceptable).
In Win XP that wasn't such a big problem, there was some swapping for about 1 minute when i started crysis, then performance was just fine.
Any hints?
Hey guys, so I just built my new computer a week ago but recently I've been having lots and lots of blue screens. The most common blue screen is Memory_Management, I know because my computer just stays at the blue screen and doesn't shut off. I think thats a reason why im having driver blue screens and not being able to start my computer correctly, sometimes my computer can't find the appropriate Windows 7 files. I've right clicked manage on my computer and I don't seem to be missing any drivers. My DRAM voltage is on auto.
[code]...
BSOD occuring randomly at no specific time.(atleast 4 times a day)All my browsers keep on crashing.Windows explorer and catalyst control center also crash a lot.Did memtest previously overnight didn't get any errors.checked the system with replacing each memory stick individually,ran similarly with each one of them.
Windows 7 X64-Retail version
one and half year old hardware(problem was there from almost an year)
OS reinstalled 3 months back.
i recently made a thread in regards to my blue screens and i will now upload more of the minidumps. they generally occur when i am on chrome and watching a Internet video. i just received one then in regards to memory_management and no reason was shown.
View 5 Replies View RelatedSo I've been having random BSOD's for 10 day's now - They appear at complete random and I can't tell why, Each time they display 'Memory Management' - I can normally diagnose them and narrow it down, However I cannot seem to do so. Can an expert have a look at the dumps and see if they can work it out?
View 3 Replies View RelatedRecently I have been getting random BSOD some say Management, other say Non Default, Bad_Pool_Header, maybe some others but the BSOD is to fast for me to read exactly what it says. I been doing my research on how exactly I can even first look at this mini dumps found a program call (BlueScreenView) When look around i can see all id the dumps there but am seeing the the main culprit is a ntoskrnl.exe. Now I am guessing this Because it was shown alot. People have said to run memory checks, your ram sticks are going bad, restore your computer, but honestly I an clueless.
I would like to know
1) What are the step to find the problem
2) How to fix it
3) How to prevent it
new help with memorymanagement thecompare and contrast the basic system and difference between mac, linux and windows
View 1 Replies View RelatedThe CPU, heatsink, motherboard and RAM came premade by 3XS from SCAN. I have made sure it's all seated properly etc.
Intel i7 2600 @ 3.4gb
8gb RAM Corsair Vengeance
Win 7 64 fresh install
Radeon HD 7850 Graphics Card.
Asus z77 motherboard.
However after about a week of usage with no errors all of a sudden I have started getting the odd BSOD, and today I have had about 20, even in safe mode.
Suddenly my computer could just black out, looks like it is turning itself off, but not completely. The fans is still running, but can't use the computer and the screen is black.And yesterday I got a BSOD also. Don't know if this Memory Management issue has something to do with my earlier blackouts, but I hope so. So that there is only 1 thing to fix ;-)Yesterday I ran Memtest86+ for 10 passes and 22 hours. And I got zero errors. See picture.
View 2 Replies View RelatedI am trying to use all the 4 GB of RAM that I have for my computer so I decided to "upgrade" to 64-bit. The only problem is that when I boot from the installation CD I get a memory management error. I know that my CPU is 64-bit capable as well as my video card. As for everything else I am not sure of. What is a way to fix this problem because I desperately need to upgrade to 64-bit.
View 3 Replies View RelatedI just bought my new laptop 1 month ago, but BSOD occurred for many times.Window 7 Home Premium
System
Manufacturer Hewlett-Packard
Model HP G42 Notebook PC
Total amount of system memory 4.00 GB RAM
System type 64-bit operating system
Number of processor cores 2
Storage
Total size of hard disk(s) 596 GB
Graphics
Display adapter type ATI Mobility Radeon HD 6370
Total available graphics memory 2746 MB
Dedicated graphics memory 1024 MB
Dedicated system memory 0 MB
[code]....
Acer Aspire 4740G. 2 years old. Last 1-2 weeks constant BSOD as per title, and random freezing up, forcing restart. On restart, random issues pop-up e.g. "Windows explorer is not working", "Login services not working (causes me to be logged into a new profile, all settings, icons, wallpaper gone)". The system has run the Memory Diagnostics test. Extracting from the Event Viewer, the results are as follows:
Log Name: System
Source: Microsoft-Windows-MemoryDiagnostics-Results
Date: 16/04/2012 09:09:37
Event ID: 1102
Task Category: None
[code]....
Windows 7 x64 Professional Hardware less than 2 months.OS re installed after MS updates failures.perfmon named failure.
View 5 Replies View Relatedi'm having issues with my Windows 7 Ultimate 64 bit PC. Every so often it will just BSOD on me. I've had a look at the errors and it mentions MEMORY_MANAGEMENT and ntoskrnl.exe, but i don't really know what i'm doing so i figured i'd get some REAL help. I've recently installed new graphic drivers, hoping that might help but it just crashed on me again.Windows was pre installed on the machine and the machine itself is only a year old.
View 3 Replies View RelatedI have been experiencing random reboots which very often fail and occasional BSOD crashes, the last one refers to memory management. I am running Panda cloud antivirus and malwarebytes.Original OS was preinstalled retail version win xp proff. Current OS full retail version win 7 64bit home premium Hardware new Dec 2006. Dual boot 2 x sata hard drives?
View 5 Replies View RelatedIm always getting this BSOD error. identify the driver that is causing it.Minidumps attached.
View 4 Replies View RelatedAs you can see the drives list is blank, and I cannot change the location and size of pagefile!
Does anyone have the same problem or have some tips to solve this?
"PFN list corrupt" on start up.
View 3 Replies View Related"windows 7 setup.exe corrupt file the file or directory is corrupt"I'm trying to install 7 32bit OEM Home Premium with the legit bought holographic CD (not a burned image of any kind) onto a Gateway laptop with a brand new hard drive.I was getting this error installing the OS the regular way booting to the cd and installing from it, so instead I copied the contents of the cd to a freshly quick formatted NTFS partition on the new laptop hard drive, then used bootsect and diskpart to setup the disk. It boots just fine and also gets the same error installing straight from the hard drive.
View 9 Replies View Related