I bought a HP LASER JET 1007. which is a USB 2.0 printer. i have two pc both are connected via a switch. There has a modem connected also in the switch which have a usb and a ethernet port. ethernet port is used to connect the modem to switch.. That means in my network i have 2pc and a modem connected. is there has any procedure to connect my printer to this network. I dont want to connect the printer in a pc, cz to access the printer i have to power on the pc always.
Originally, i had one network running under a Dir-665 router where all the computers under that could connect to the printer (HPPrintPC) on the computer (which is connected to the router.After moving to uverse, i have two networks, the one above and now the 2wire network due to uverse.The computer with the printer is connected to the 2wire network, and all the other computers are connected to the Dir-655 network. The computers on the Dir-655 Network can't connect to the printer on the 2wire network but can ping the computer it is connected to.
I have installed a wireless Epson Workforce 610 printer (it is fast!) but if it is not turned on when I boot I get a notification message "Could not reconnect all network drives".Is there a setting which will prevent this from displaying? One other computer which has the same drivers does not show this message, so it is puzzling.I disabled all the Epson drivers in Startup but that did not help.
I had my computer at my home, connected to my home network. I moved to a Corporate apartment, which has a different network, and now I can't print to my printer, which I brought with me. I did set the new network as my 'home' network, and folowed instructions, but it does not seem to be working.
THe printer is a C6280 Photosmart, and is wireless enabled, but my new place doesn't have a router to attach to. Basically, I'd just like to connect the printer directly to my computer, since I will be the only one printing to it.
I have a laptop with windows7 and i want to connect it to network and share printer on a computer with windows XP. It doesn't detect the computer and even when i have changed sharing settings on laptop.
I have 2 computers on my home network. My desktop is running Windows 7 ultimate 32 bit and I have a kodak 5500 Aio connected to it. I also have a laptop that's running windows 7 home premium 64 bit that connects wireless. I was able to print until today and now I can't print from the laptop. I can see the printer in the add printer window but comes up with cannot connect with error of 0x0000000d
Can anyone advise how I would go about fixing this. I am trying to connect to a network (I have a dell running on windows 7) and it keeps telling me that windows is unable to connect to the network-this is before I can even enter the security key. I know it is not a problem with the wireless because other people are able to connect to it fine.
New windows 7 Home Premium desktop that can print when the printer is directly connected but can't print when the printer is connected to an XP pro pc. It can see it but we're getting a "driver cannot be found on the network" flag.
We have just added our first Windows 7 pc to our XP network. I would like to connect to the Windows 7 PC to a shared "Epson lq-590" printer on one of the XP machines.According to the Epson website the only drivers available for this printer are through Windows 7 update in the "add a printer wizard". If the printer is directly attached to the Windows 7 PC the driver installation via "add a printer wizard" works without a hitch. When trying to add the printer over the network the Windows 7 "add a printer wizard" cannot find the driver for the printe
I went to the HP site to download the latest driver for my printer model, but on this page it says:HP PSC 1200 All-in-One Printer series - HP Printer Install Wizard for Windows 7 - HP Business Support Center "The drivers for your HP product are already included in the new Windows 7 operating system! You do not need to download drivers to use the product.Simply connect the printer to your computer with a USB cable, and Windows Update automatically installs the driver for your product."
I just upgraded all of my computers to Windows 7 Professional and Office 2010 Professional Plus, and they're all running great. Much faster than the previous configuration, Windows XP Professional SP3 w/Office 2003 Standard. I'm using one computer to store all of the file backups and share the printer, a Dell Photo AIO 924. Everything's working fine, except for the printer. The printer prints from the computer its directly connected to, and I have it shared. However, when I try to connect other computers to it, I get an unable to connect to printer error with code 0x06. I checked a couple of things, Print Spooler service is running, network passwords are disabled, and all computers are in the same workgroup. I've gotten this to work before, but that was a while ago when I was running Windows 7 Enterprise trial on the same computer, everything worked great
I need to connect a printer via crossover cable to a Windows 7/64 laptop. The printer has a USB port, but it is defective. I created a xover cable. How do I set up this printer (HP Deskjet 6940) using the xover cable connected to the ethernet port on the laptop?I found this thread, but as the last post indicates, it lacks the details needed to do the job. Installing printer via Ethernet Cable I connected the printer to the laptop with the xover cable, ran through the printer wizard to install the HP6940 drivers as per the Windows 7 printer installation routine, but nothing will print. I tried the MS FixIt routine and still no printing. All I see is an error - printing for this printer when I open up active printers.
I have a Kodak Hero 3.1 connected to my Motorola Surfboard SBG8560 modem/wireless router. It connects fine and I can find the printer and even print hen my computer is connected to Ethernet but not when I switch over to wifi. This is on a computer running windows 8 rp but I know the os is not to blame because it is not found by my roommates mac on wifi or my other roommates windows xp machine. i figure it must be a router setting that i am missing. When i run arp -a in cmd this is what i get:Code[CODE]
I've got two Vista Ultimate computers. Both have the same username and password. Same workgroup name.
Password protected sharing is enabled on both. I shared a folder on computer 1, and added Everyone to the security tab, with full control.
When i try to map the folder from computer 2, I can see computer 1 listed. But when I click on the + next to it, it asks for a username and password (which I did not expect to be necessary since they are both the same user account and password) and when I enter it it says Logon Unsuccessful.
I have a local network and the printer connects to a wireless router using a USB cable, I am about to get a wireless printer. My Lap Top connects to the internet wireless throu the Router when I bring the Wireless Printer will I need to connect to the printer thru the Router or directly to the printer
I am unable to connect my computer with a Network printer in my organization. I am running Windows 7 Home Premium-64bit on my laptop. The problem here is, when I try to add a new printer as:Devices and Printers> Add a Printer> Add a network, wireless or Bluetooth printer.The wizard searches for a few seconds than my LAN automatically gets disconnected.The other way round I've also tried to manually add the printer but it didn't work. It gives the error "Cannot Connect to Printer. Error 0x0000007e" The printer in Network is RICOH Aficio 8001 PCL6.I've tried to contact my IST department but they are saying that we are also unable to connect it with 64-bit operating system.
I just installed Win 7 home premium. When I go to my printer which is on the wireless network, I can print with no problems. When I try to scan I go to HP Solution center to scan and it I get a message that my device is not connected. I then reinstalled all the Win 7 drivers for the HP C7280 all in one printer and when I go to connect to the printer device, I get the error message that it can not connect to the printer. The printer did show up. I also disabled the norton firewall.
I download the software for my Brother printer for installation. When I Run the installation till "Now plug in the printer with USP port and turn on the printer", nothing shows just like the printer did not plug in.
so i'm having an issue trying to connect to the shared printer on one of my windows 7 x64 machines.i've tried setting the network on windows 7 to "work network" instead of "home network" thinking that the workgroup being the same on all systems will do the trick but it doesn't.
I have a LaserJetprinter with a bad USB port, and I want to connect it directly to my laptop using the ethernet port. Since there is no internet at this location, I have been using the USB port.If I connect the printer directly to my laptop what type of cable do I use (crossover?) and what kind of port settings do I use (TCP/IP?) and how do I set this up correctly?
I am trying to connect my printer HP Deskjet 1280 to my new laptop - Windows 7 64bit and have also have 32 bit. I have used the disk that was supplied with the printer, but no luck and when I go to the HP website, they tell me the driver is automatically installed, yet a message on my laptop says the Deskjet 1280 doesn't have a drive.
I have a Epson Photo RX585 Printer which is giving me one hell of a headache since I upgraded from XPpro to windows 7 32bit.I cannot get the Computer to communicate with the printer or is it the printer to accept the computer communication.I have downloaded the latest driver for the printer from epson home site and installed it.The automatic configuration of the driver into the appropriate port is not appening and asks me if I want to install it manualy (with me thats like asking a bus driver to fly a jumbo Jet).I did try getting directions from the internet but got lost and finished up with my printer driver attached to a LTP1 port instead of a printer USB port, needless to say it still wont work.I then decided that I would add USB ports myself Dont ask me how I didit but some how through the device manager I typed in USB001, USB002 and USB003 and the computer seems to have accepted these port as it has not thrown them back at me yet.My next venture into the unknown is to configure the printer with one of these ports to see if it will work.The computer will not configure automatically to any of these ports and I do not have a clue as to how to do it manually.As you can see by the details above anyone after reading this who is brave enough to attempt to give me instructions as to how to get this compuer of mine and printer onto speaking terms again is either mad or deserving a medal.
