Windows 7 Wont Boot Up After Bios/cmos Reset?
Feb 20, 2012
Okay so i recently bought a new desktop computer and i left it on over the night and in the morning it was frozen, so i popped out the battery and waited 5 min and then i put it back. Now when i start it up either i get the white and black screen with 2 options, to start windows normally or to run system repair, it fails with repairing and restoring. And sometimes when i start it the windows 7 thingie with the like 4 orbs who create the flag just freezes and a blue screen with white text comes up for 1 sec and then it reboots and i get to the black and white screen with those options that i mentioned before.
View 8 Replies
ADVERTISEMENT
Dec 20, 2012
I reset the cmos by pulling the battery, and now the comp won't boot, won't show the F2 F^ boot options in the upper left corner, and won't react to any key pressed, just shows a messages saying to run setup, but no clue how to get there using usual keypressess.
View 2 Replies
View Related
Mar 23, 2011
Seems my CMOS data corrupted... Sometimes, I can't able to get into BIOS setup, as there is no option seen in the screen to enter by pressing DEL (I have a Gigabyte MB).. After couple of restarts, my MB showing me as normal that (Press DEL to enter setup).
View 2 Replies
View Related
Mar 18, 2012
reset my CMOS... Seems my CMOS data corrupted... Sometimes, I can't able to get into BIOS setup, as there is no option seen in the screen to enter by pressing DEL (I have a Gigabyte MB).. After couple of restarts, my MB showing me as normal that (Press DEL to enter setup)..
View 9 Replies
View Related
Apr 4, 2011
We just build a new system to play around with the Intel Rapid Matrix RAID
Asus P8P67 MB + 8GB RAM+ I5 2500K + 2xWD BLUE HD SATA 6 IN SATA 0 and SATA 1 ( SETUP AS RAID Mirror)We install the Window Ultimate 64 Bit in the RAID Drive .... No problem after all the drive install We also allocate 50GB for doing a image backup (Drive F) We restart the system and goto BIOS to set the HD from RAID to AHCI ( This is the situation happen when the BIOS reset)
Supprise me the system can boot form the Drive ...... (In Device Manager .... I see two WD 1TB HD instead of one 1TB RAID Drive) But when I use Disk Manager it takes really long time to run... I can't wait for that long and shut down) On My computer I only see one HD with 4 Partitation ...
I restart the system and Goto the BIOS to reset back to RAID...and it give error..
I but the W7 Ultimate Boot disk to repair but no success.. Try to load the Backup Image .... cannot find it...
From the old time .... if the BIOS reset it will set to IDE Mode ... Then I am'not able to login to window it will come up blue screen and I just reset to RAID it will fine.... But nowadays... the New MB set Default AS AHCI...then I encounter this issue.... Lucky ... we just testing the new system now..
If I have a cooperate customer want to setup a RAID drive and suddenly Power Cut Down.... BIOS reset..
View 1 Replies
View Related
Aug 17, 2012
My computer suddenly froze, well it appeared that it had, it was infact just the Keyboard and Mouse. I turned it off manually and re-booted. Lone behold the Keyboard and mouse still don't work. This has happened before and I found a fix for it by following some steps to do something like an electrical reset or something where you turn it on and off and hold a button in for a certain amount of time etc, BUT I can't remember how to do it.
View 7 Replies
View Related
Dec 28, 2012
I bought a Windows 8 laptop, ASUS Q500A, and reformatted it with Windows 7. I went into the BIOS and used "Restore Defaults" and now all Boot Option Priorities are deleted. Each time I boot the laptop, it automatically goes to BIOS (or UEFI). I tried inserting the Windows 7 disc so I can access Startup Repair or Command Prompt but it freezes before it could get anywhere even when I tried it with an external CD/DVD drive. I cannot get the laptop to boot to the hard drive or CD drive at all, how I can reset the boot option priorities so it will be boot to the hard drive again.
View 1 Replies
View Related
Jan 17, 2013
How do I reset the bios password that is required when I use F2 on my gateway laptop NV53a
View 5 Replies
View Related
Mar 13, 2012
I have a problem with my bios password,could you plz suggest me how to reset bios password.
View 3 Replies
View Related
Jul 17, 2012
The HDD password was set by mistake in the Insydeh20 BIOS and i don't know what it is. The computer is a Toshiba Satellite laptop. This is a REGISTERED password on the HDD that was set using the BIOS.
View 3 Replies
View Related
Sep 27, 2012
Can I download content to reset my bios password?
View 4 Replies
View Related
Dec 27, 2012
I want to reset or remove my bios password from pcg-61112L sony vaio laptop.
View 4 Replies
View Related
Nov 5, 2012
So, we have multiple computers that the wireless capability stops working randomly and can be fixed by going in to the BIOS and resetting it to the defaults.
View 5 Replies
View Related
Mar 20, 2012
my laptop have a problem of bios password, model is acer aspire 5810T?how to reset bios password?
View 3 Replies
View Related
Apr 30, 2012
how i to reset my bios password compaq presario R3000
View 2 Replies
View Related
Oct 5, 2012
I tried:
1. Installed Acer Power Management Utility V6.00, It is located in programAcer, but it can not be run from Start. Because it is not there. (I do not know how to index it and let it show in Start menu.
2. CmosPwd 5.0 does not work in Windows 7 64bit version.
3. The cmos coin battery seems located under the keyboard. It is difficult to move three latches locking it.
View 6 Replies
View Related
Mar 19, 2012
i want to reset or remove my bios password from VPCEB14EN sony vaio laptop.i m unable to boot my hard disk from other cd/flash etc.
View 1 Replies
View Related
Aug 25, 2012
so i did a bios update, and it wont boot after the update.its a asus m4a79xtd evo (rev 1.01g)i dont have a backup of the bios
View 3 Replies
View Related
Feb 28, 2011
send me how to install window 7 in cmos setup
View 1 Replies
View Related
Oct 26, 2009
I am choosing which OS to boot by changing the boot order in my BIOS. To me, this seems clean and simple. I built 32 bit XP on one disk, then removed that disk from my system, installed a different disk, and built 64 bit Windows 7.
When both disks are installed, I change the boot order to select the OS I want, and each OS sees and can use the files on either disk.
Am I asking for trouble here, or is this as clean as I think it is? What I want is one set of user document files which can be used from whichever OS has been booted.
View 2 Replies
View Related
Jul 5, 2012
I have a Lenovo ThinkPad X60 laptop with Win7 32-bit Ultimate and an SSD (I know, I know, just go with it. I'm building a desktop soon). I could list the specs, but that's useless for this problem (I'd think).
At times (not always), when either resuming from hibernate or booting up from a shut down, the computer generally freezes at the point right after the BIOS screen. So it's just a black screen. This is before the window that says "starting up" (literally a window... the Windows logo). Whenever it freezes, it NEVER goes to the boot screen of Windows. I'm assuming this is an error with the hard drive, since the OS is on the SSD and the boot screen is from the mobo. However, this only started happening after a rather heavy fall to the ground that cracked many parts of the plastic shell on the computer. It still works occasionally when I can get it to boot up (nothing different when it boots up... same settings and everything. Spontaneous).
I have tried:
1) Cold reboot
2) Removing battery
3) Going off only battery
4) Unplugging EVERYTHING from the computer
I have not tried chkdsk yet. Is it necessary? Also, would there be a log somewhere of what happened? It never booted into Windows.
View 4 Replies
View Related
Nov 16, 2011
Windows 7 ultimate 32 bit suddenly switched off, reboot does not show on screen which reads "HDMI CHECK SIGNAL CABLE". Using ATI HD4350 fanless with heatsink connected via HDMI lead. tried another monitor using white dvi cable monitor stays blank then shows power saving mode. So that eliminates the monitor & hdmi lead. Could a duff graphics card show this error? No on board graphics. Unable to get into bios no bleeps, Windows 7 dvd no good either, all fans come on and motherboard MSI X58 on board indicator light goes from amber to green when pc turn on so m/b must be ok.
View 7 Replies
View Related
Aug 6, 2012
In the chaos of moving to a new house yesterday, a box my friend was moving ripped and a bottle of beer smashed onto my open and powered on laptop, scattering both liquid and glass everywhere. We immediately powered down and removed the battery, and placed the laptop upside down and mopped up the excess liquid from the outside as much as possible, and set it to dry upside down on a towel.My laptop is a Lenovo U330, I had my brother install Windows 7 on it for me last year, but he kept the disks so I don't have any of them.Several hours & some blowdrying later, we attempted to start up the laptop (I would have preferred to wait longer, but I needed to know if mine would work in case I needed to borrow my friend's for the week). The laptop will load the lenovo startup screen, and then flash the windows loadings screen (with the option to press f2 or f12) for a few seconds before recommending that I run startup repair. Which if I select it, will freeze after a few seconds. Usually my laptop's pretty noisy, but while the battery light flashes as if there is activity going on, there's no noise coming from it at all.
View 7 Replies
View Related
Jan 21, 2009
First off, Windows 7 is very cool; I might use it more than vista now that I got internet for it, but that will have to wait for a month or two. My first question is: when I boot up my comp, and I have to pick either vista or Windows 7 (I have Windows 7 on another partition), I usually leave the room while my comp is booting, so after 30 seconds the BIOS picks Windows 7 as the default OS because its first. I would really like to boot up my pc while doing something else, and I would love for the BIOS to pick Vista after 30 seconds instead of Windows 7 because I use Vista for games and such. Is there some way of doing that or do I have to sit around throughout the start up and manually pick Vista?
My second question seems a little picky or over the edge, but when I boot up my comp and have to pick an OS, it prints "Windows 7" while underneath it it prints out "Microsoft Windows Vista". Is there some way to add 'Microsoft' in front of Windows 7 when Im picking in the BIOS? It doesn't look as good without the Microsoft.
View 9 Replies
View Related
Dec 25, 2011
Sometime when i turn on the PC , all fans are running but nothing boot up no beep sound either. I have to push and hold on power butt to utrn it off then turn it on again couple time to get it to boot up but then it freez up in few min!I have try to boot in bios mode but get same problem it freez!!! when i try to do memories test it tell me i have hardware problem and again it ran memories test for 2 min then free
View 6 Replies
View Related
Oct 22, 2011
Hall drivers/updates for my new build are complete, and when i boot, the first asus bios screen comes up, then displays components (as usual), but then goes back to the first start up bios screen. This cycle happens three times before "starting windows" comes up (i have windows 7 ultimate 64-bit). I have a OCZ vertex 3 60Gb SSD, i5 2500k, asus p8z68-v pro, corsair vengeance 8gb cl8 1600mhz ram, and to get to the windows screen takes 40 seconds. Can anyone explain why it is displaying the bios start up screen three times before 'starting windows?'
View 4 Replies
View Related
May 10, 2012
I just swapped out my old motherboard since it was quite rubbish (really old packard bell m-atx board) for a brand new ASrock P5B-DE motherboard.
However after installing the board and plugging everything back in exactly where it came from on the old board, the PC cant boot into windows 7 64bit. I've tried the repair option and it doesn't work.
I've tried disabling and enabling various options in the BIOS. Also tried removing the memory and only using 1 stick then tried both sticks in different slots and that hasn't changed anything.
I've tried inserting my Win7 CD but it doesn't seem to boot from the DVD drive (will keep trying to see if it can).
System specs are:
Intel core 2 Quad Q6600 @ 2.4GHz (using Freezer Pro7 CPU cooler)
Samsung DDR2 800mhz Ram (2GB x 2)
160GB 7200RPM Hitachi HDD
ATI (XFX) 5830 1GB GPU
Zalman 500W PSU
my next point of call is to try a lower end GPU as i've still got my Nvidia GTS 250 and doesn't use any external power from the PSU.
(P.S. I'm not overly bothered about doing a clean install as i recently did one anyway and I haven't had a huge amount of programs installed on the pc since then. But if I can fix this without a clean install that would be preferable)
View 11 Replies
View Related
Oct 25, 2012
I updated the Bios from toshiba site after that my windows won't start and I can't even get to Bios setup (F2) or Boot sequence (F12). and windows get stuck as soon it starts. I can't even access to Factory Restore. I have no image. For information I am using Toshiba Qosmio X770-107
View 11 Replies
View Related
Mar 26, 2011
how can i get a driver for my webcam,it's model is- cmos pc camera rfc39020
View 2 Replies
View Related
Apr 21, 2011
I already went to "msconfig" and chose my default OS. Bios still stops at the Windows Boot Manager to show me the only OS there is for me to choose/use. How can I go straight to my desktop without the Boot Manager?
View 2 Replies
View Related
Dec 19, 2012
Yesterday I was attempting to wipe my hard drive as I was putting my laptop for sale. Whilst it was wiping my laptop crashed and would not re boot properly but I was able to access the BIOS . I stupidly changed some settings following some advice on a forum I now cannot find and when I tried to re boot it stays on the philips page for around 10 minutes. None of the keys work, like F12, F2 ect. After ten minutes it give me a screen thats says 1.Insert your Windows installation disc and restart the computer.2.Choose your language settings, and then click "Next".3.Click "Repair your computer."If you do not have this disc, contact your system administrator or computer manufacturer for assistance.Status: 0xc000000fThis is how I understand it as my system is in Polish and Polish is not my first language and with technical language I am not fluent and I beleive thats how I made the mistake in the first place in the BIOS.
View 9 Replies
View Related
