Windows 7 DVD Not Booting System
Oct 19, 2012
I installed linux along side win7 dual boot system. when i removed linux partitions ex4, my system become unstable after all I had to reinstall win7 too. But this time win7 sp1 dvd scratch less media, it could not boot my system. sometimes messages showed "mbr not found" sometimes "ntldr missing" then used simple win7 dvd "not sp1" it booted my system and installed properly. But still problem is there win7 sp1 dvd not booting my sysem. is it bad file system problem or what it is?
View 1 Replies
ADVERTISEMENT
Oct 30, 2012
I have a computer where it keeps booting into the "System Repair" menu. It hasn't done this before.
Recently had lightning struck a transformer. Phones all rang and tv went bizzare! Lucky we had a surge protector.
Well...the computer wasn't doing this before. It use to boot fine but after the transformer problem it starts to boot. Then goes into a screen where it says "Launch System Repair" and "Start windows normally". Even if I select start windows normally it would still go into the system repair menu. I ran PC Check and my hardware all passed. My hard drive passed the SMART self extended test too.
Right now I'm booting off Hirens 15.1 into Mini XP.
View 12 Replies
View Related
Jun 24, 2012
I have a HP mini , which comes with windows 7 starter preinstalled .so, i which has 2 disk drives c,d and the HP recovery .in disk management i marked (HP recovery) "mark partition as active " , pressed ok on the warnings .the problem is that my laptop doesn't boot and gets to the HP recovery manager and when i cancel it to boot normally a message says "the installed program cannot start.press OK to turn off the computer".
View 6 Replies
View Related
Mar 14, 2009
I have installed windows 7 beta on my windows XP machine,SATA hard disk. Issue: Unable to boot into win 7. XP boots fine.
C: had XP. Installed windows 7 to F: drive.
After installing I could boot into windows 7 and could work on it.
Later i found that windows 7 would boot (with the windows 7 boot manager) only when the windows 7 installation disc was on dvd drive.Otherwise only XP is shown in the boot selection menu - the standard old menu.
Now, even with the dvd, it does not boot into win 7. Instead it goes to the Windows 7 install screen. But the installed files are still there in F drive. So, tried repair in win 7 for start up, but no problems were found.
Tried easyBCD from within XP, but that didnt help booting to win 7.
One peculiar thing I noticed is, although I installed win 7 to F: drive, when seen from within win 7, the installation drive was shown as C: drive. In reality the C: drive contains the xp installation. From within win Xp, win 7 installation files are in F: drive only. Is this the problem?
Now how do i boot into windows 7? Will adding some lines to boot.ini help in getting the windows 7 to the OS choice list?
View 7 Replies
View Related
Feb 12, 2013
I'm running Win 7 Pro 64 bit on a system using an ASUS P5Q Pro motherboard.henever I'm away from the computer for an extended time, I always go to Start and put it in sleep mode. I've never had a problem with it waking back up and resuming until today. I had to leave the house for a while, so placed it in Sleep mode, but then realized I'd forgotten to do something, so before it actually went into sleep mode and shut down, I started moving the mouse to stop it. Nothing happened and I eventually heard the usual pop of the speakers indicating it had shut down into sleep mode. The monitor was blank. I kept moving the mouse, but instead of waking up and going back into Windows, I heard the same beep as heard when rebooting, and the Cmos stuff appeared on the screen as if booting, but then stopped and I saw "Press F2 to load defaults and continue" ....which I did. It started to do something then stopped with no HD activity and nothing on the screen. Nothing.
No activity. I then shut it down using the button on the front of the case and let it sit for a couple minutes. Pressed the On button and heard some activity with the green light and red activity light lighting. Sounded like a normal boot with the beep, speakers popped on, and it looked like something was going to appear on the screen, but....nothing. I could see the monitor had been activated....just nothing displayed. All activity stopped within a few seconds with only the green light still on. The internal fans were running, but nothing happening. Again, I shut it down using the power button, and shut the power supply off as well. I let let it sit and tried again.....same thing. It starts to do something, then quits with just the green light on and the internal fans running. It simply will not boot...and until this episode has been running great.
It seems to have something to do with pressing F2 and loading the bios defaults. I'm wondering if it may be locked in sleep mode. I contacted the guy who builds my systems and is unfortunately out of town and I'm in the middle of a magazine layout. We tried everything, but it simply won't go past that one point. It's not even POSTing. He suggested removing the motherboard battery in order to reset the bios and if it happens to be locked in sleep mode, removing and replacing the battery will delete any sleep mode settings.After reading about similar issues, I removed the motherboard battery and changed the jumper for 10 seconds to reset the bios and finally was able to get into the bios setup.
View 7 Replies
View Related
Nov 2, 2012
My system is booting up extremely slow its slow to show f2 for bios option as well so I thought its a hardware prob. I ran a memory diagnosis and this is what comes up. Its a customised pc so need to call a particular products manufacturer if its a hardware problem.
View 1 Replies
View Related
Feb 12, 2013
I bought a PC with a quad-core system with 16Gb RAM, a 128Gb SSD C: drive and a fast 1Tb D: drive. I just discovered that I have an 18Gb C:pagefile.sys and started wondering about the pros and cons of having this paging file on my SSD C: drive. Given that I have 16Gb RAM, I could probably get away with no page file at all. I could certainly manage with the pagefile entirely on the "traditional" D: drive. Are there any guidelines on pagefile placement in the SSD era?
View 9 Replies
View Related
Jan 7, 2012
I can't use my system it hangs up after booing. I have used several antiviruses in safe mode but all futile.
View 1 Replies
View Related
Sep 28, 2009
My main desktop is a Windows 7 installation but my partner still works from a laptop with XP installed.
She has a port replicator connected to my monitor and both our computers feed into it.
I was wondering if this scenario is possible;
Create a disc image of her system and install it on a new drive within my tower. (this will also have the added bonus of convincing her that we need a new bigger monitor!! )
Dual boot Windows 7 and XP.
Curveball;
Is there a way to allow her laptop to ghost the main install so that all files are synced or alternatively allow a ghosting of the whole installation?
The motivation behind this is that should she need to go away - always has a day or so notice, she can just pick up her laptop and know that when she opens it up she will just be able to carry on.
Curveball 2;
The laptop is a dell, so will all the drivers and bloatware that is on her install cause issues if the disc image is installed onto a desktop?
(before anyone asks, I have a retail XP licence which I will rely on for EULA etc.)
View 3 Replies
View Related
Jan 22, 2011
My Win7 HP x64 PC has two hard drives, each partitioned into two volumes:
My C: and E: drives are each half of a 200GB drive, both NTFS.
My D: and F: drives are each half of a newer, 1TB drive, both NTFS.
My F: drive has around 400GB of 'stuff' that I want to preserve.
I've been trying to migrate the win7 installation from C: to the first partition of the 1TB drive with two different tools (Norton Ghost and the built-in Windows backup utility) and both fail identically.The backup procedure itself appears to work in both cases.Restoring the backup to the first partition of the 1TB drive "works" in so much as I don't get any errors either way.Creating the requisite boot structures also work, as the O/S appears to be bootable.However, when the restored O/S makes it to the login screen, two flaws are evident:
1. The keyboard absolutely does not work.
2. If I log in on an account that doesn't need a keyboard (no password), I see "Loading desktop", then a few seconds "Logging out" and I'm back at the login screen.
If I look at the event viewer logs (booting up with the O/S on the smaller drive), I see numerous events like this:"The AVGIDSAgent service failed to start due to the following error: The system cannot find the file specified.""The Windows Live ID Sign-in Assistant service failed to start due to the following error: The system cannot find the file specified."
[code]....
View 1 Replies
View Related
Oct 4, 2012
One of my machines has an error message flash by very quickly each time I boot it up. It goes by too fast to read the whole thing, but it starts with "Alert! Previous attempts at booting this system have failed at checkpoint..." The computer is a Dell XPS 8000 and runs Windows 7 64bit. I'm having no problems with the computer at all. The message goes away and Windows 7 continues to boot up just fine. I'm not sure when the message started because I usually hit the power button in the morning and walk away. Is this message indicative of a problem or can it be safely ignored if the computer has no other symptoms? I've searched and only found issues where computers won't boot or have other problems along with the message.
View 7 Replies
View Related
Aug 6, 2012
Booting with the 32bit dvd does not bring up the Repair service but goes onto Starting Windows screen from the dvd itself. Then PC lockup. Every time.How to stop DVD at booting to bring up System Repair service?
View 1 Replies
View Related
May 17, 2012
i have an m17 r2 alienwAre laptop.in the bios menu the sata option HCAI is selected but when the comp boots it says no operating system is found when booting for bios sata option RAID it runs fine. But the comp should be on HCAI in order to run features that a specific to that computer . I have tryed reformatting but in HCAI it on finds the second of 2 500g hard drives but the partition with the boot is on hdd1 not hdd2 . Boot up again with RAID it finds both and and I can reformat have tryed to reset the registry and have tryed using drivermax to find out if I'm missing sata drivers I've also tryed reinstalling my bios from the dell
View 6 Replies
View Related
Mar 10, 2011
I recently (~2-3 months ago) installed windows 7 on a brand new 1TB hard drive. This hard drive is broken into two partitions - C & G. Windows 7 is installed on C; and G is only for data storage etc. Here is the description of partition C from Disk Management:
C: Simple Basic NTFS Healthy (Boot, Page File, Active, Crash Dump, Primary Partition) 98 GB
Unfortunately, "System" is missing from that description. Somehow "System" ended up on hard drive L - an old 80GB IDE drive that has migrated from build-to-build. This drive has just started on the *hopefully* slow road to death. I decided to retire this drive when I discovered I couldn't securely erase it because it is the System partition (there is only one partition on this drive).
So, how I can relocate the system drive data to another drive (preferably C) in the safest way possible. I found a solution here: [URL]. But I don't want to copy the entire contents of L to a new drive, all I want is the data needed for booting, and to securely erase everything else on L. Looking around, it seems I may be able to boot from a Windows 7 repair disk and recreate the system files on C, but this seems risky and likely to require a full re-install if something goes wrong.
View 4 Replies
View Related
Jul 10, 2012
I'm trying to restore my Windows 7 64bit machine to its factory settings at the moment, and I've tried the following but they've all failed.1.) Boot up and hit F8, select Repair computer, but then it just boots Windows normally.2.) Create System Repair Disc, and from BIOS boot-up, choose boot from DVD-RW, but when it does that and loads Windows files, Error 0xc000000d and winload.exe missing comes up.3.) When I tried to insert the installation disc that came with my computer, it's not recognized and nothing happens (during boot from DVD-RW).*Note - Just today when I tried to do a system restore, it said that I had no previous restore points, but I just restored a week ago, so that might add some info.
View 3 Replies
View Related
May 6, 2012
Firstly I should say that I am primarily a mac user, and it is not my laptop I am posting about. Although I am reasonably knowledgable about Windows, I haven't used it since XP, about four years ago, and so am pretty rusty.Basically, my girlfriends computer randomly turned off about a week ago, she assumed it was a dead battery, plugged it in, and then when it turned back on it wouldn't boot displaying error message: missing operating system.As it is a Dell laptop it didn't come with any installation discs, and I totally forgot to even make a repair disc when we got the laptop. I managed to get hold of a Windows 7 Installation Disc and license key for Windows 7 Ultimate 64 bit through my university. I think the laptop was previously running Windows 7 Home Premium, but that's all I know, and I'm not entirely sure of that fact.
Anyway, burnt the .iso to disc and have tried to boot several times from DVD Drive. The laptop loads the files from the DVD fine, and gets as far as the "Starting Windows" screen, where it seems to get stuck for a few minutes, until it becomes a black screen with just a cursor (the cursor still moves). This also happens with an 64 bit repair DVD I also managed to get hold of.
View 9 Replies
View Related
Jun 19, 2012
Earlier xp but after win7 the booting not show xp at booting time
View 1 Replies
View Related
Nov 4, 2009
Created it with no problems, apparently at least. My BIOS is set to boot from CD drive, so why won't my machine boot from the system repair disk? There were no errors when disk was created. My machine just boots to windows.
Anyone else experience this with Win 7 Professional?
View 9 Replies
View Related
Mar 23, 2012
I just recently upgrade my system's OS from Win XP to Win 7 but I'm facing some problems with my Win 7. Whenever I boot up my system without my GPU installed, it boots up just fine. But as soon as I install my GPU i.e., GT 240, Windows 7 doesn't respond after "Starting Windows" screen or simply fails to boot. I also faced the similar problem while installing my Windows 7. I resolved that one by removing my GPU while installation.
View 9 Replies
View Related
Feb 3, 2013
I have a Medion Laptop and it froze so I forced it off. Now when i load it in any mode (safe mode freezes after avg file) It will go to a black screen or a 0xc0000009 I/O error message.I've run it in start up repair and there aren't any system restore points available and start up repair took 17 hours before i decided to turn it off! What is going on!? My hardware doesn't make any strange sounds and my bios recognises my Hard Drive.Luckily, there's nothing important on the laptop so i don't mind if we have to reset it to factory settings as i have the Windows 7 installation disc as well!
View 8 Replies
View Related
Jan 19, 2011
I have a Dell Inspiron E1505 with Windows 7 (32bit) and it's not booting. I tried safe mode with and without networking as well as the startup repair and system restore options.Startup Repair basically said that it couldn't repair this computer automatically and this: [code] System Restore said that it couldn't access a file and something about anti-virus as well as "An unspecified error occurred duing System Restore. (0x 80070005)"..Seems like my only bet is to do something with Command Prompt... but I seriously don't have the slightest clue as to what.
View 7 Replies
View Related
Apr 12, 2011
Booting with windows 7 and xp SP3. I tried installing 7 first and then XP and it only booted xp! So i tried in reverse putting XP then 7. BUT THEN ONLY 7 BOOTED ! I cant get the option of which id like to boot i have 2 sata harddrives.. I just cant seem to make it work any help?
View 1 Replies
View Related
Apr 15, 2011
My CPU was working finw with windows XP. it has only 512+128 mb ram..I just want to test if Windows 7 works on my PC.I instered Windows 7 and during installation when it rebooted the initial screens where Pentium 4 ht comes becomes blue.after that its hanging there
i opened PC and removed the CPU battery and tried, result was same
i removed RAM and installed again. same result
i removed all the datacard to dvd,hdd, and floopy same result.
View 3 Replies
View Related
Aug 20, 2012
No new softrware, no new hardware, I have not made any changes to it at all. I turned it on yesterday and after the Dell logo, it went to a black screen with a blinking cursor on top left.I turned it on and off a few times with no change. I finally got into the diagnostic screen (F8)and it did a thorough scan of all hardware. It came up clean. I shut it off and turned it back on again and Windows finally came up. I then did a scan of all windows files and that came up clean. After that I did a system restore and didnt have anymore issues with Win 7 booting up. Then about 45 mins ago I turned on the laptop and AGAIN the black screen came up with the blinking. I have no clue what else to check. I could call the place where I bought it from and Im sure their crack team would most likely find the problem only after giving up the laptop for 2 weeks which is what i was trying to avoid.
View 1 Replies
View Related
Aug 15, 2009
I burned the .iso windows 7 file onto a Sony DVD using Active@ ISO at 4x burn speed. Everything went fine with the burn and then i put my dvd burner (HL-DT-ST DVD+-RW GSA-H31N) as the first in my bios and then restart, but then it doesn't boot...
I don't think the DVD is the problem as i put it into my mac and it shows the 2.36GB that the windows 7 .iso file is supposed to be. But interesting enough it doesn't show in vista and every time i click on the dvd the computer freezes up.
Also i tried a dvd earlier and it booted up but it didn't work (i didn't realize that the dvd was only 702mb...)
Any help? Suggestions?
View 3 Replies
View Related
Dec 10, 2012
Everything was working fine till last night.When i switched on the laptop today the system started rebooting infinite times.whatever i enter the system keeps on rebooting.No use with startup repair,it stalls the entire system on clicking.Unable to boot from CD too.
View 1 Replies
View Related
May 5, 2011
So just to get this out there, i already know that it is caused by a hardware problem. The reason why is because this started happening after i replaced my case and psu. [URL]And just to let everyone know, i dont have the repairs disks that came with my computer and i dont have a recovery image.
View 3 Replies
View Related
Feb 12, 2012
it happened after i upgraded my Mobo and CPU, i booted my PC up and it got to the windows 7 logo and midway through that little animation it froze and rebooted, that is as far as it gets,i have tried a system repair, a system restore to an earlier point, i tried a MBR fix, nothing has worked
View 9 Replies
View Related
Aug 16, 2012
It freezes just before the splash screen on normal boot.when i try to repair it the monitor goes black, but computer is still running.safe mode had the same problem as startup repairI've tried reseating the connectors to the hard drive, reconnecting all the power cables, using a different power supply and continuesly rebooting but nothing makes a difference.
View 5 Replies
View Related
Dec 27, 2012
I try to boot frome a DVD but doesn't want to boot, and any key i use doesn't work.It's infinite boot.after and after.And any key ai try doesn't work. Work just ctrl+alt+esc and i enter in red screen (grub4dos.etc with options with "windows with SLIC loader...etc). I don't know how to boot frome here. The common methot to boot doesn't work to me. I just want to reinstal windows 7 profesional again to never have this problem again.
View 1 Replies
View Related
Jan 4, 2013
somehow my hard disk partition became dynamic. i formatted system and insttaled windows 7 ultimate in the dynamic disk partition.from then onwards system is not booting. only black screen with cursor on the upper left corner of the black screen.if i am not wrong windows 7 cannot boot with dynamic disk. i will have to go to the disk management and after conversion of dynamic disk to basic disk with deleting all the volumes (data). it is possible to boot withwindows 7. but system is not booting...not opening..so i cannot go to disk management.hrad disk is showing some partitions with system reserved.except system reserved all the partitions are shwoing dynamic.and in only one partition formatting option and installing OS option is coming while i booting system with OS DVD.
reinstalltion through OS DVD is possble by booting through OS DVD. but in advanced option repartition option is not coming. the one partition in which i installed OS previously, only in that formatting option is coming.in other partition neither formating option is coming nor extend.
View 1 Replies
View Related
