Upgrading To Windows 7 64bit With Software RAID 0 In Box?
May 18, 2011
I am wanting to upgrade from Win7 32-bit to Win7 64-bit. I am told this will require a clean re-install of Win7. That isn't a problem in and of itself. My question is what will happen to the other RAID 0 arrays in the box? Since they are "software" RAID 0 arrays that were created by WIn7 32-bit after it was installed will they survive intact when I install a new version of Win7 on the base drive? My base drive is not part of a RAID setup. Will the new Win7 64-bit install recognize the two separate RAID 0 arrays automatically? I hate the idea of having to try to backup a couple of TB of data from the RAID 0 arrays (and then restore it) just to install Win7 64-bit.
Biggest bottleneck in my system right now is my boot drive, which is a WD velociraptor. I want to change this for dual 120GB SSD's in Raid 0 configuration. Can anyone walk me through the steps to copy over the existing Win7 64 install onto the SSD's, I dont want to have to load everything again
I finally got Windows 7 and I was hoping I could finally switch to 64-bit (I took long enough to join the rest of the world) but I am having issues upgrading to it from XP.Now, I do know that I can't directly upgrade from XP to 7 without losing all my junk, I know everything is compatible (ran the Upgrade Advisor thing), and I'm following the process on the official site url...However, I can't seem to get it to boot from the disk. I've changed the boot order to the "DVD/CD" option being first, Hard Disk second and Floppy last but it seemed to just ignore the DVD. After that, I even changed the boot order so it would only try to boot from DVD/CD and set the other two settings to "Nothing" BUT it completely ignored that and somehow just started normally. I even tried opening to Boot Menu as well, going down to the DVD/CD option and pressing enter, but that didn't do anything whatsoever.
I have been trying to get windows 7 Ultimate 64 bit installed onto a raid I created with two ocz agility 3 ssds. Everytime I try loading the drivers at install it gives me an error stating the drivers are unsigned and to install a 32 bit OS. When installing a 32 but OS, the install works normal and the computer runs fine. I am just wondering why it wont install for 64 bit considering I would much rather run 64 bit. I went to both the MoBo's website and the main companys website for the chipset drivers (AMD) but have both turned up with the same error.
I want to install windows 7 64 bit on my system which has a raid array. My motherboard is an Asus M3A78-T and my CPU is an AMD Phenom 9950 Agena 2.6GHz Quad-Core Black Edition.
I'm planning to replace the 32-bit OS with 64-bit Windows 7 Ultimate. This laptop can support 8GB as mentioned in the catalogue. I guess the processor i5-430M is the first generation processor. I'm getting two 4GB RAM modules fairly cheap with same speed specifi'x.
I've no plans to trade off this laptop because its a rare "breed" - Made in Japan by Fujitsu and after 2 years of service it still runs extremely well.
I know that one copy of windows 7 can only activate one computer. I have two, one already with windows 7 32bit installed and one without windows 7. I plan on buying a new one, installing windows 7 on my second computer and upgrading windows 7 to 64bit on the other. If I upgrade, will windows use the old activation key or require me to enter a new one, because that computer came with windows 7 32bit so I don't have the disc.
I want to upgrade my windows 7 32 bit installation to 64bit so I can add some extra ram to my system, but I was wondering if I do a backup on my 32bit install, format the drive, and then install 64 bit windows 7 and recover from the backup will it work? Can you use a 32 bit backup on a 64 bit machine?
i have brought new desktop and installed windows 7 32 bit and now i would like to install windows 7 64 bit how to do that. is there any other patch should i download... or should i install new operating system itself....
I have a Dell XPS M2010 that I recently changed to 64 bit running Windows 7. Since I have had the computer there have been issues with the display driver not responding but when I check for updates, it says best driver is already downloaded. Not a day passes by when the display crashes and recovers on the average of at least 5 times.There has to be another driver that will work for this thing but I am not having any luck finding it. Can someone please tell me how to fix this issue
The reason on why i want to upgrade from a 32 bit to 64bit is because i have some extra ram that is not being used. Also i want my computer to be a little bit better when playing my games.
Processor : Intel Core 2 Quad CPU Q8200 @ 2.33GHz 2.34 GHz Memory(RAM) : 4.00 GB System type: 32-bit Operating system Graphics : NVIDIA GeForce G100 64-bit capable Yes Model : Aspire M5700
I tried looking online about this I need to know if there's a big difference between 12GB of system memory and 16GB of system memory. I don't play many games but I do convert HD videos a lot and these programs are a pig on ram. I have 8GB now and have ordered 2 4GB sticks and was wondering if I should stay with 2 4GB sticks and 2 2GB sticks(total12GB) or should I upgrade to 16GB.
I am trying to go from 32 bit Vista to 64 bit Windows 7. The 32 bit Vista was installed by mistake. My system can handle a 64 bit OS. Now I have finally found the time to upgrade. But the 64 bit installation DVD can't be read from my OS. I have tried setting up my CMOS so that I can boot from the DVD but I have run into some issues. First of all, when I look at my keyboard during the boot procedure, I noticed that the little light which indicates that one row of buttons are to be used for F1 - F12 keys, the little green led light goes on and off. Sometimes, during the boot process, it is on, sometimes it is off.
The CMOS procedure tells me I can hit F12 and set the boot order. I can hit F12 but when I go into that menu, I notice my keyboard is dead. The CPU does not accept any commands from me. So I need to power off and power on and try again. The CMOS procedure tells me I can hit DEL and that launches the whole CMOS utility. There I can set the boot order so that the DVD is run first. But when I save and exit, I notice my keyboard is dead again. This time, the screen is showing things being set and loaded and I am prompted to hit any key to show I am sure that I want to boot from the DVD.
I hit the Y key and I hit the spacebar, but it becomes clear that my input is ignored since my keyboard is being ignored. And the ol' Vista OS is loaded. Is there any way to set things up in the VISTA OS to force a boot from the DVD? I guess I can load the OS in save mode and format the C drive, but if I do that I might risk having a dead computer since the CMOS does not seem to be trusting enough to boot from the DVD drive even if you tell it to.
Microsoft has this page of links: [URL] And then there is this link: [URL]
And the Notes section specifies that I need boot off the DVD drive: "To install a 64-bit version of Windows 7 on a computer running a 32-bit version of Windows, you'll need to start, or boot, your computer using a 64-bit Windows 7 installation disc or files."
Ive been trying for 3 days now to install a clean os on a raid 0 setup. I can get the array setup in the bios np, but when it comes time to actually install the os i can't. Reason being i cannot for the life of me find a raid driver that is signed by windows>< The south chip is sb700.
ASUS P7P55D-E EVO 2X80gb Western Digital SATA Drives 2x2TB Samsung Spintpoint SATA Drives
I have already been using the machine with another 80Gb Western Digital SATA Drive with Windows 7 Pro 64Bit installed and now want to convert to RAID 5 for redunancy in case of Drive failure (We all say we will back up but we are all lazy when it comes to it LOL).I have taken out the original OS drive and plugged it into the E-SATA connector on the MOBO, gone into the BIOS, turned on RAID for the SATA Ports on the MOBO, and connected the 2 X 80Gb Boot drives. Entered the Hardware RAID Controller POST, and created the RAID 5 Volume from the 2 X 80Gb Discs.Now boot with Acronis Wester Digital edition.Clone the Original 80Gb Disc to the new Raid Array.Shut machine off, remove original OS 80gb Disc from E-SATA port.Boot machine.It starts to boot, and gets as far as the Windwos 7 Microsoft 4 Colour logo and then I get an error and then have to boot into Windows 7 from DVD and go through the repair process.When the Repair has run it reports the following:
The following startup option will be repaired:
Name: Windows Boot Manager Identifier: {9DEA862C-5CDD-4E70-ACC1-F32B344D4795}
The following startup options will be added:
Name: Windows Recovery Environment (recovered) Path: Recoverye52d0bc2-1f15-11df-af10-d764fe3715b8Winre.wim Windows Device: Partition=D76190 MB)
A copy of the current boot configuration data will be saved as:C:BootBCD.Backup.0001 However it fails to do the update How do I get this RAID to boot successfully? I *don't* want to have to re-install the Operating System as that is just too painful a thought?
I just preorded the windows 7 upgrade and I'm wondering, is it possible for me to "upgrade" (Clean install) my windows xp 32 bit to 64bit windows 7? I've read the windows 7 FAQ and it said of your upgrading from XP, a clean install is required to upgrade but does the upgrade offer allow for xp 32bit to be upgraded to w7 64bit?
My OS is XP Pro 32-bit. Using Easy Transfer 32-bit saved selected files to external HD. After installing Win 7 64-bit, can I use the resident Easy Transfer to reapply/import the earlier saved files?
I have a computer running a 32 bit oem version of windows 7 home. I really need to change this to a 64 bit version. I do not want to do this illegally. Can I buy this upgrade copy of 7 professional, perform a clean install of windows prof. 64 bit with the upgrade disc, and then use my current oem 32 bit home disc and or license key, to validate that i do in fact have a copy of windows currently.
So technically I wont be "Upgrading" from 32 to 64, I will be re-installing. I have asked several tech savy friends, and while they don't think it cant work, they are unsure. Essentially I am asking if anyone knows what validation windows requires for its upgrade discs. I am given to understand it requires you to put in your original windows disc at some point, and i assume your original key, but will it accept a 32 bit disc/key?
I am running Windows Vista Home Premium on my Dell Inspiron 1721. Can I upgrade to windows 7 Ultimate 64 bit software. I have purchased Windows 7 Ultimate and received both 32 and 64 bit software discs.
Recently, going back over my quasi-gaming rig, I found out that my processor (Intel Pentium Dual-Core E5200) is 64-bit, not 32. I've been running 32-bit Windows 7 ever since I got it. When I bought Windows 7, I did so off of the Microsoft store, so I always have the option to go back into my purchase history and download a new .iso of either the 32- or 64-bit release. I did so, and ran Microsoft's USB/DVD tool for Windows 7 to put it on a USB drive (I didn't have any DVD-R's on hand) and it all seemed to work perfectly fine. But when I try to boot from the USB drive, it goes from the "Windows is loading files" screen to the "Starting Windows" screen, then gives me an unexpected error and forces me to reboot. I already tried redownloading the .iso, in case it was a corrupt download.
I have recently upgraded my pc to 64-bit and Im having huge fps drops whenever I run the games that I used to play fine in 32-bit (Aion Online and Guild Wars 2). On 32 bit, I was running with 30-35 fps with highest settings, but now I'm running both games with 9-15 fps regardless of the visual settings.
I have tried reinstalling the AMD driver, as well as the chipset drivers using -overall and -overide. I have tried disabling my sound driver, and I still get the same result.
I have tried googling some fixes for my issue, but so far it has been fruitless. Aion has a 64-bit client which they say, would increase the game's performance gradually, but I have yet to try it since it's not working as of the moment.
What I'm concerned about is when I run Guild wars 2 client (just the launcher itself), I am noticing a drop on my computer's fps. I never tried to overclock my cpu nor my gpu since I have an old school mobo.
Here are my specs:
CPU: Intel Core 2 Quad Q8300 2.5 Ghz MOBO: ECS G31T-M7 RAM: 4GB DDR2 800 (2gb x 2) HDD: Samsung HD161GJ ATA (150 GB) GPU: ATI HD 5770 PSU: Raptor R500
I'm about to do a destructive install to Win 7 64bit, to upgrade my existing Win 7 32bit installation. I already have a partition in my hard disk ( K: ) where existing User profiles/data are stored. Luckily there is only my profile and one for a guest user. I've read through some of the Tutorials on this site on how to create new users on a different drive/partition at the point of installing Win 7, and I've read how to change the User Folder Name of a profile.The fear I have is that the newname user in the 64bit will obliterate the oldname at the point of being used for the first time.
Installed a new M4 ssd today and loaded windows on it. Previously i was using 2 raptors in raid 0 for the os and programs. I re raided the 2 raptors and connected them to the jmicron ports and set them up for raid in bios, then created the raid 0 array no prob. Windows doesnt see the array when loaded up and i have the latest rst drivers installed..did this prior to the os install on the ssd. using the x58 e760a1 mobo. under device manager, the raid controller has an exclamation mark and no driver installed yet i have the latest rst 10.8.0.1003 installed..
Can I upgrade from Windows ultimate 32bit ver 6.1 ( build 7600) to windows 7 ultimate 64bit edition and keep all of my installed programs and files ?[meaning not having them moved to a new folder called windows.old]
I have tried to find the way to do this, but without success as I cannot see the wood for the trees.
I have a mature Windows 7 system, with so many applications loaded that rebuilding from scratch is just not an option. I have a 300MB Velociraptor wholly given over to the OS and another empty 300MB VR. I want to extend, that may not be the right word, my OS to use both disks in Raid 0.
I have Win 7 Pro 64 bit installed on an ASUS P7P55D LE motherboard which supports RAID 0,1,5 and 10 using Intel Matrix Storage Technology through an on board Intel P55 chip set. The system was assembled in Nov 2009 using two Western Digital Caviar Black 750Gb drives in RAID 1 as Drive C:. (I now know from Western Digital Customer Service that I shouldnt have done that, but lets move on from there). Last December, an error message informed me the RAID array was broken and identified one of the 750 Mb drives as needing replacement. I happened to have a spare 1.5Tb WD Caviar Black at the time, so I pulled the 750Mb drive and replaced it with the 1.5Tb drive. Life was once again good. Then on July 4th (wouldnt you know) there was a repeat of the December 2011 error message telling me to replace the other original 750Gb drive. Okay so I had another 1.5Tb WD Caviar Black laying around (dont ask) and did a similar swap out. Thats when I emailed WD Customer Support asking about the 750 since their diagnostic software said the drives were fine. Thats when I learned that I should be paying lots more for enterprise quality drives if I want/need RAID. Well thats not what ASUS says in their advertising, but live and learn. All thats prologue, because my real question is whether its possible to break the hardware-based RAID 1 array and set up a Windows 7-based RAID 1 with the two 1.5Tb WD Caviar Black drives without having to reinstall Windows 7.
