I'm trying to transfer between my Desktop computer (XP) and laptop (Windows 7). When I do it wifi it only transfers at speeds between 1MBs to 3MBs. When I physically connect to my router I get better speeds at 10-11Mbs. However in both cases on large files it loses connection.It says that connection lost/failed and gives me option of retry/skip. When I hit retry it still doesn't work. When I disconnect and retry that method it starts up again from scratch however rarely does it fully transfer a file. These files are anywhere from 2GIGs to 4GIGS.I don't have anti-security on either computer. I'm using new Netgear router.
i have bought a notebook with vista 32 bit home basic and didnt like vista so i upgraded it to windows 7 64bit after 1 day usage. Generally i found new os fine but i have a problem with file copying from my desktop (running xp sp3). My transfer speed is only 1.5 mbyte per second. Notebook has atheros 5007eg (54mbit) wireless lan and desktop has realtek gigabit lan. And my router is airties rt-205 with 125mbit wireless signal. I have done the following things but it's still same.
*netsh int tcp set global autotuninglevel=disable. *Turn off Remote Differential Compression. *Disabled Remote Assistance. *Unchecked ipv6.
Here is my problem. In this case, I am trying to transfer pictures from one of my XP systems to my Windows 7 Home Premium system over my wired network. Between the XP systems, things run fairly quick. But not with 7 involved. When I go to transfer the 47 pictures that I want, it tells me that it will take 18 minutes. And this is for only 66.7MB of data. Tell me this can get better. Being new to 7, I have no idea where to look for the problem. I tried searching Microsoft's site and the help files on my system. I just can't find a solution.
Here is some more info, and maybe some you don't need. On the Windows 7 system, I can access all the shared folders on my other systems (all XP SP3). If I go to the network map, my other systems are marked as "The following discovered devices can not be placed in the map.". I don't know if that is a problem or not. The reason I did that is because I was reading through the Microsoft site on file sharing and that was mentioned. It also mentions a program called LLTD, which may be needed on 32-bit XP systems. I tried installing that on my XP system, but it said I didn't need it.
As far as the file transfer, while sitting at my XP system, access is denied when I try to access the shared folder (for my pictures) on Windows 7. Now if I transfer them to the Users/Public/Pictures folder, it will transfer them in just over 5 minutes. Still a little slow, in my opinion, and not where I want them. Why can I transfer there and not into the folder I want them? And why is quicker to transfer while sitting at my XP system?
I have made sure that all the systems have the same workgroup name. I have also tried disconnecting the power from my modem, router, and all systems then powering each one up one at a time. That was suggested to me before. It didn't change anything.
One last thing. While starting my Windows 7 system, as soon as it was at the desktop, I tried to transfer the pictures again and the transfer took off. Almost immediately, it said that there was 20 seconds left. It was flying like I thought it should. Less then a minute into the transfer, it hit a wall and changed to about 20 minutes. Go figure. I checked my settings for the folders I want to transfer to and they are set as shared. Maybe at that point, a security program started up. I don't know. I do have a trial version of Norton's Internet Security installed. It came preloaded with the system. I was thinking of removing that and going with Avast free. I have checked any firewalls and did disable them. No difference.
I tried to list everything I've tried. Hopefully, some helpful info in there. I find it strange that I can access the shared folders but not transfer from them. Any thoughts on what to do? Is there a setting in Windows 7 that needs to be changed?
I have a Dell XPS 15Z with gigabit ethernet port, have dgs 1005d gigabit switch and WDTV live hub also with gigabit "capability"... The network cables should be fine...
The issue is that the file transfer (these are usually HD movies) from my laptop to WDTV are rather slow having in mind it's a gigabit network connection... The speed tops 15 MB/s. Same thing if I connect WDTV directly with my laptop.
The switch indicates (green light) it has set-up a gigabit connection both with WDTV and my laptop.
I have disabled autotuning, RDC, AV software etc. Tried with jumbo frames, disabling flow control - EVERYTHING
issue: file transfer from/to xp from my laptop very slow while PC is turned off. as soon as i turn pc on all gets good. this looks really weird to me, all of these 3 are connected with cable not wireless, i also have tried changing the port of the laptop cable on the router but didnt change anything.
Using Easy Transfer from a Windows 7 desktop to a Windows 7 laptop [over a network] a 17.5 GB data partition transfer took over 5hrs. It all went smoothly but ... is this a reasonable time ?
When I press "Connect or Disconnect", it pops up an infobox saying "You are currently connected to: xnetwork"
However, there is no option to disconnect from the network. This is extremely frustrating; apparently I'm blind, but I've tried disabling and re-enabling the adapter to no avail.
I use Windows 7 Pro on our company LAN. I had to connect temporarily to another computer on the LAN to access some file shares there. Now I would like to disconnect. I haven't found any way to do this.
I have a network storage drive that has seen its last day but I still have the icon under my computer when I try to disconnect from it it tells me the drive does not exist.
I have an Acer Netbook and just plugged an external hard drive in via USB. I have 2.18G to transfer and it is telling me to wait another 2 hours and 15 minutes.It has Intel Atom N570(1.66GHz) and win7 Starter.
This sounds really noobie of me but is it possible to improve local network transfer speed by adding a 2nd network card. I was planning to connect one exclusively for lan transfers and another one hooked to a separate wireless router.
Right now only a maximum of 3 users can stream SD videos off the PC before it gets a little choppy.
The pc in question runs on windows 7 and it's board has built in gigabit, I happen to have a spare gigabit card.
I'm running Windows 7 Ultimate x64 on my Computer(...) and I have recently found a problem that's pretty annoying: The file copying is really-really slower than on Windows XP and I mean that if I want to copy a folder which is about 650MBs over to a USB Flash Drive it takes about 1 day(what??) and the transfer rate is like 300KB/s. I have tried to look for solutions on the Internet but they haven't turned out handy. Could someone please help me asap as I need to give the USB to someone in a couple of hours?
I am hoping someone might be able to shed some light on this problem. When transferring a 3 gig file from my NV+ to my internal hard drive I get speeds of around 300 Kb/s and message saying the transfer will take 18 hours.When i transfer the same file to my wifes computer over the same network the speed jumps to 30MB/s which is what it should be. I cannot understand why this is happening as my wife's computer is way slower than mine with only a core 2 duo processor and 2 gig of ram
i have been having this problem for about three weeks now and my transfer rate is very slow.... and at the end it even takes longer... sometimes it even gets stuck at somepoints but resumes after quite a while
I have a Vantec NexStar TX NST-210S2-BK Hard Drive Enclosure - 2.5" SATA to USB 2.0 wit a 120 GB Segate Harddrive in it connected to an Asus K61-IC laptop and my transfer speeds on all my USB Ports are acting super slow.Also, Just recently I've had a balloon tip start popping up in the taskbar telling me that if I hook my USB Devices up to a USB 2.0 Port it will run faster. I'm pretty sure that all my USB Port's are 2.0.
I have 2 desktop computers and one laptop on a network, all three are also part of a Homegroup. When I try to copy files from the main Admin PC to the laptop it slows down to less than 15KB/s. I thought perhaps it was the wifi reception but even when connected with Ethernet it's still terribly slow to the point that a 300MB folder takes 2 hours (estimated time). I end up cancelling the transfer sand sometimes windows explorer ends up crashing. However when I copy files from the second desktop to laptop it is normal speed. No lag, no glitch. All the files I tried to copy where share, available to Everyone. Everything else works fine, streaming video and music from the main admin PC is flawless, I just can't seem too transfer files from the main Admin PC to the laptop.
I recently completed a clean install of windows 7.
I have the i7 950 on the ASUS Rampage II Extreme motherboard.
I am currently experiencing extremely slow usb tranfer speeds.
I get transfer rates on average of 650 KB/second.
I checked the device manager and 2 of the 8 usb controllers say enhanced. The other 6 do not. According to the specs of the board, all 8 should be usb 2.0.
I have tried letting the system update the drivers, but for all, it retains the current driver. I even went so far as to disable the controllers and restart. All 8 returned, but with the current drivers.
I tried using the install CD that came with the mobo, but it states that it cannot run using the current OS.
i just notice that my usb transfer is really slow around 11mb/sec for my usb stick and around 20mb/sec for my external hard drive. I noticed this change right after installing SP1. (I'm on windows 7 ultimate 64bit.) The thing is that it happenned in a particular moment, i was transfering files to my external hard drive the same day i installed Sp1 and in the beginning of the transfer the transfer speed was normal, around 60mb/sec. Then my Internet security software (Eset Smart Security) tells me that a process has changed in i think it was taskhost.exe (i am not 100% sure but i know it was a windows process), it ask me do i accept it, i press ok accept the change and then i saw my transfer speed slowed down right away to something like 20mb/sec.
As of recently (for the last couple of weeks) I noticed that the transfer rate to my external WD Elements SE 1TB drive is very very slow (~2MB/sec). This wasn't always the case, and the drive was much more responsive than that.
I searched about this topic extensively and the only thing I found was an issue with installing Windows 7 SP1 that in some cases screwed up the USB2 drivers. This was supposedly addressed by KB2529073 which is installed on my system. However, I'm still experiencing this ulta slow transfer rate.
I know there are very similar threads but like I said I cannot find a solution. [code] I recently noticed the transfer rate really slow, at an average about 1.5MB/s.I have tried enabling Better Performance option but what happens is that it starts really fast and then goes down to about 1.5MB/s anyways and usually just freezes or stops.I also have a laptop, its an Acer Aspire AS5745DG-6681. Specifications are:Intel Core i5-480M, 15.6" HD (1366x768) LED-backlit, 4GB RAM, 500GB HDD, Blu-ray Combo Drive, NVIDIA GeForce GT 425M 1GB, Wireless N, HDMI, Webcam, 9-cell, Windows 7 Home Premium 64-bit.I updated the RAM to 8GB on the laptop.Using the same external hard drive, I can get rates at an average of 30MB/s and better performance is also disabled on the laptop.I Don't know what the difference is they both have Windows 7 64 bit, just the laptop is Home Premium and my desktop is Windows 7 Enterprise.
I bought a hp dv5-2230us 3 days ago with a i3 380 4 gb ram and win 7 home premium . I tried to copy a 1GB file onto an sd card and it took over an hour! it was going at about 200kb a sec or so. On my old satellite A105 with 1 GB ram and T2050 1.6 GHZ it took about a min to transfer the same file on the same card running ubuntu. It was not a linux specific file. Only thing that has been installed is firefox, flash, java, and microsoft updates.
I have recently had to format my hard drive and re-install windows. I have also had to replace the motherboard, CPU and power supply. I borrowed a 1.5 TB Freecom firewire external hard drive from a friend to back-up important data before the format, but the transfer speed is uselessly slow now that I am attempting to put the data back on the drive.
I have tried:
- updating the drivers for the firewire card
- switching to 1394 OHCI Compliant Host Controller (legacy) in the device manager
- Optimizing the drive for 'better performance' as opposed to 'speedy removal' in the drive's properties.
As things stand at the moment, I am getting about 400 kb/ps transfer speed from the external to my on-board drive. As you can imagine, this is virtually useless to me, considering I have hundreds of gigabytes worth of data to transfer.
My western digital usb 3.0 external hard drive is giving only 1 MB/Sec transfer rate. I know its really very slow. Can any one let me know what we could do increase the speed.
have been struggling with my system taking 2-3 minutes to find drivers for any memory stick I plug in to any of 3 USB ports on my Acer 1810T. When the process finally completes, the transfer speeds are about 1MB/s or less.Another (possibly related?) problem is when I insert any SD card in the dedicated slot for the first time, everything is fine. Once I remove and either re-insert (or insert a different card), nothing appears. I get a message saying "process is already in memory". I have to reboot to get things working again.
My problem is slow usb transfer rate - at first it start off real good (70-80 mb/s then within 10 sec it drops down to 3 and even 1 mb/s). 1.5 mb file gets into my flash drive in 10 min or so. Now I've formatted flash drives, no change. Write-caching enabled, "best performance" for flash drives enabled... Tried on a Lap-Top - transfer rate is not so high, but stable all the time - 15-12 mb/s. Remote Differential Compression disabled. Transfer rate within the hard drives in my computer is OK (I got 2). I don't know if it's the Windows 7 problem or the motherboard problem or hard drives config problem.
Here is my info: Windows 7 Ultimate 64 bit HDD's: Samsung 500bg and ST 320 bg, both 16 mb 7200 mobo - GA-770T-D3L, v.1. RAM - 8gb Phenom IIx6
My problem is windows 7 hangs and freeze when access 2003 server Enterprise edition. This is not a small network, one of the biggest network.i have doubt on individual users on domain. before 2 months we had department wise users mean, for example Accounts@domainname.local. But after we created the individual users like john@domainname.local to all users. this is i believe the cause of problem. When we acess the server via the software it freezed for 5 seconds and then repeat to normal state. And after some time it hangs for 2 minutes.
