why, when connecting wirelessly under Windows 7, to a wireless access point I am unable to change the "Network Type" from Public to Home, thus no connection to the Internet is allowed? I cannot change any of the parameters of the network at all. Under XP on the same network I have no problems at all.I have set up three access points by simply adding additional wireless modems (of the same brand as the primary modem), turning off DCHP and U PnP and assigning a unique IP address, to avoid DCHP conflicts (as I understood it).Which change would I have to make to the access points such that Windows 7 fully recognises each access point and allow me to assign them to type "Home"?
I have just reinstalled Windows 7 64 bit and it won't see my local network. I'm running a hardwired network, my switch is a netgear RP614 set to act as a dhcp server. I had the 32bit version of windows 7 installed and that picked up its network address fine to start with and then just stopped working. I have tried hardcoding the ip address onto the network card but that makes no difference.My xp machine connected to the same network works fine.
It appears that windows 7 isn't picking up the ip address from the dhcp server as it should. it gets a default address of 169.254.107.37 whereas my network is 192.168.0.0 I have put in the default gateway and the dns server addresses that my isp uses but this makes no difference.
I have tried turning off the dhcp flag as recommended by microsoft in case that is the problem but that made no difference and it was working under 32 bit for a while without the flag turned off.
I have installed the nforce drivers in case it was the windows drivers causing the problem that made no difference. I have run a network capture and that shows that it is seeing the dhcp packets from the dhcp server.
I have done everything I can think of and everything I can find recommended by Microsoft but all to no avail. Any help with this greatly appreciated as I really like windows 7 and don't want to have to downgrade my system.
Stuck with my local area connection problem.I can not access my internet,under networks options there is no local area connection or any thing like that.I have also tried to format my computer to fix the error but no success.I have also tried to uninstall and then install the drivers but it was of no use but when i troubleshoot the it says the drivers are not installed properly.
I am running win 7 and my LAC says "unidentified connection" no internet access. I can still connect wireless to other connection. I am running comcast broadband connection through a marvel yukon ethernet. I can't get my work done from home anymore!
Above is the error that comes up after I troubleshoot this issue. okay so to start off let me say the things I have done.
1. I have restarted my computer multiple times and restarted the modem and router. 2. I've checked my services to make sure that that weird code is not there and it was not.
This problem just came up recently and had no issues with it before and this computer has been running for over a year.
I have Brother MFC7340 printer connected to my HP home premium Windows 7 64 via a USB port. There is no ethernet connection. I want my Windows XP computer, connected to the local home network via ethernet hard connection through my wireless router to be able to print either with a hard connect or wirelessly to this printer. I am having trouble figuring out what to do and have tried various strategies to no avail.
Basically my ethernet capability flew out the window ranomly the other day. Wireless works perfectly however.. before ...the other day.... it has been working solidly for almost a year Im plugged into a router which is running off my cable modem, both sitting less than a foot away from me. Also hooked up to the router is another computer, and my xbox the xbox works but the other computer cant seem to get a local connection either.
at first i assumed they were having an ip conflict of some sort, but why now after all this time?
I have tried:
- ipconfig /release - /renew - abolishing bonjour - taking the other pc completely off the router/network - updating drivers.....rolling back the updates - different cables different ports -plugging directly into the modem - and asking nicely
im on my laptop, Dell studio also the first time i noticed this happen was directly after having powered down the modem and router.
below is the ipconfig Microsoft Windows [Version 6.1.7601] Copyright (c) 2009 Microsoft Corporation. All rights reserved.
i am having problems connecting to Xbox live because it has no internet access and i have tried lots of things and nothing is working. here is the story behind it.... i had tried connecting many times before but it wouldn't work but one day i tried and i changed sharing on something (IDK what i forgot) and it worked so i had live for a couple of days. then one day my bro was online and the power went out in the house for a while, the next day i tried to connect and it wouldn't... on the when i plug in xbox ethernet to computer
Unable to see home network computers in Windows Explorer Network screen.
I have a home network with 2 laptops and 1 desktop. The desktop I use as a "file server" in that all work done on the laptops is stored to the desktop. The desktop computer name is HAL. One laptop is fine and sees the network. The other just stopped seeing it; rebooted the laptop; rebooted HAL; did a number of refreshes without any luck. I opened EXCEL and found a worksheet that was listed that I knew was saved on HAL. Was able to open the file and when I tried the SAVE AS I could navigate through all of HAL just as normal. Went to Windows Explorer and still no HAL listed as a COMPUTER on the NETWORK. I have a internet connection so I know I am making it to the router at least. And when I check NETWORK AND SHARING CENTER it shows an active home network. The laptop is running Windows 7 Home Premium Service Pack 1 Build 7601.
Last night I was on the internet at home absolutely fine and my laptop automatically downloaded an update, since then I have been unable to connect to my wi-fi. I deleted the updates and was still unable to connect, so I tried to used a system recovery restore point and every one I use starts but fails to complete.So, I did a factory reset after around 8 hours of trying to sort it out today and I STILL have the same problem. I can plug in the cable to connect and my housemate is having absolutely no issues connecting and neither is my phone so now I am at a total loss what I should do to resolve this. Prior to the factory reset I was able to connect to the wi-fi but it was stating no network access/limited access and now it simply won't connect to my internet at all. It finds my full strength signal but will not connect.My drivers for the Broadcom 4313 802.11b/g/n card are the most up to date and the laptop (HP G62) says it is working fine.
I tried to google for this phrase : windows 7 unable to access "Local Uesrs and Groups",,,,but all I found is related to XPMy issue is I have a standalone windows 7 ultimate 64 bit, "Local Uesrs and Groups" has a read cross on it Can't access "Local Users & Groups"- The error was: Invalid syntax - Petri.co.il forums by Daniel Petri Q. When you attempt to access the Local Users and Groups snap-in in Windows 2000 you receive 'Error loading type library/DLL'?From the cmd I run sfc /scannow the result was :Windows Resource Protection did not find any integrity viola
I have two HP desktops running Windows 7. One is connected by wire to my router because the router is right near that PC. The other PC is downstairs and connected wirelessly. There is also a Mac downstairs, connected by wire. We also have an internet TV, Playstation 3, smart phones and tablets. All of these last items connect wirelessly to the network without problems. The HP PC downstairs can see and access my PC upstairs, as well as all my external drives, media server etc. I can see and access the Mac. I do see the other HP PC in my network folder, but when I try to access it, it won't work.I have discovery turned on on both. Strange thing is that sometimes, it works. But only now and then, and there doesn't seem to be any reason to this.
I thought that maybe mixing wired and wireless devices could be a problem, but all the other devices are fine. Also, I forgot that I sometimes use my Vista laptop, and that connects fine to other devices. It's only that one PC downstairs that I can't access. Is there a way to remove it from the network folder and maybe have windows 'find' it again?
my home network w.7 desktop and wifi xp laptop were on my home network each could access each others folders via wifi. [no user log in on auto access]
all went wrong this morning on the Windows 7 desktop the network see's the xp lappy but refuses access see administrator. been trying all day and got nowhere.
I currently run windows 7 home premium on both my PC and laptop (64bit). I wish to remotely access the PC from the laptop via the home network. As home premium does not support this should I upgrade to windows 7 professional to get6 this facility or purchase seperate software?
When i am in sch, i can use my sch wireless.However, when i reached home whenever i try to connect to my wireless network but its say unidentified network. My sis have no issue with the internet.The problem is solved whenever i restart my modem. Anyone here can kindly tell me how to solve this problem? I am running on windows 7 professional with my sch domain connected to my com.
I am having problems with my daughter's laptop accessing the internet with her wifi, She accidentally reset her laptop back to factory settings. She also didn't make any recovery disks. The problem is now the laptop keeps asking for a network user name/Password when she tries to access the internet. I have researched this issue but to no avail. I am curious as to how to resolve this issue. I feel the only way may be to reset the wireless router back to factory settings and start again.
My wife has a home based photography business. Her studio is located on our property. Currently her network consists of her PC, a Motorola DSL Modem/Router from ATT and an external USB HD.
She would like to be able to access her photos that are at her studio from home, say on a laptop but I am unsure the best method for this. She needs to be able to access these images in such a way that she can post-process them in program such as Photoshop at home, and then save the image so that it updates that file in her studio when shes completed the post editing. So, basically it's like being able to edit images in 2 places while keeping the original files and the saved processed images in one central location.
I don't know if this means NAS, something in the cloud, or simply remote accessing the PC through Windows. Or perhaps some other method that I don't know about.
I consider myself to be decently informed when it comes to computer stuff but I want to get this right the first time around so I figured it best to gain insight from those who are more skilled than I before moving forward.
There's a program I use (Pocket Informant iPhone Outlook Sync) which requires that my PC and iPhone be on the same network in order to sync.
The problem is that it works only when using my home network. When I'm at home, from my PC I am able to successfully ping my iPhone, which is connected to my WiFi network. This works whether myh PC is also ethernet-connected or WiFi-connected.
When I travel, however, even though I successfully connect to the WiFi network on my iPhone and PC, I am unable to ping my iPhone.
I have tried disabling the Windows Firewall and I get the same result!
I can't believe that all these different WiFi networks I connect to (airport, hotel, work) that they all have a configuration issue, so I'm thinking that the reason for the discrepancy must be because of some setting/configuration on my PC/home network.
Is there anyhing else besides disabling the Windows Firewall that I can try?
When i try and access a network share windows seems to be searching for files on my HD. Also i cant find the "display run command " option in start menu properties.
Until recently I ran windows xp. I shared a built in wall Ethernet jack with another desktop. I used my router (Linksys Befsr41) as a switch by disabling dhcp and connecting the wall ethernet and the two computers to the Lan ports on the router. The other desktop until recently was also running windows xp, but was upgraded and is now an apple imac running os x lion. My internet briefly stopped working but I was able to reset my router and get my internet running again. I then needed to reformat my build and installed windows 7 ultimate 32 bit. I cant quite pinpoint my problem. If I connect straight to the wall ethernet jack i have internet access. However if i use my router as a switch to get internet for both my pc and the apple imac, I will not have internet access. Sometimes the internet does indeed come back on in this circumstance, only to get disconnected again shortly. I am not sure who to blame because the router worked fine when spliiting ethernet for xp machines, and I have internet access when running straight from the wall to my pc
I have recently been having difficulties with connecting with my wireless connection. We have a in-home router that is connected to two computer's downstairs by cable. I however own a Acer, Windows 7 laptop that I mainly use upstairs and I get a Excellent signal strength.I have connected to my Home wireless connection before with no problem but recently the connection keeps coming up as ~Identifying... No Internet Access.Also when I have had connection to this network prior to this problem the connection is under Home. But when I try to connect to the same network it comes up as Public or just keeps Identifying. I have the connection set to Connect Automatically.Also the yellow triangle with the exclamation point almost always pops up immediately when I reboot my system or after I Disconnect and Connect the network again. I have tried Disabling and Enabling the network in the adapter settings and this does not work either. In the manage wireless networks tab, I have repeatedly deleted the connection and reentered the security password and again put it as automatically connect but it still comes up as Identifying. I have seen many people with this same problem and have tried many of the suggestions to no avail.It is rather bizarre because my connection will be in this Identifying state for a while and randomly connect properly and I have no idea what makes it go off and on so erratically. I just had it working again for a few days and it is again acting up.
I have two win 7 computers on a home network and I would like both machines to have full access to the hard drives on either machine, not just share folders. How is this done?
Printer plugged into Win7 box - how to print from remote XP machine? describes an original difficulty I had getting remote computers (laptops and desktops) to print to a USB printer connected to my Windows 7 box. Read far enough and you'll see that I solved that problem using Networking issue - Win7 printer, XP remote machines.Fast forward 13 or so months. Since that time I have replaced the printer, I've had a motherboard and processor issue with my box (since fixed), and no interruption of things working as they should. My printer - Canon ip4800 series - is USB hardwired to my Windows 7 computer, and the other home computers - two Windows 7 laptops, an XP box, and an XP netbook - can print to the printer, and view files on my Windows 7 machine, over our wireless home network. And that's been constant through the changes described.
Then yesterday, for no known reason, my daughter's Windows 7 laptop stopped being able to print. She'd send jobs to the correct printer, but they'd just queue up, with the queue visible from her machine, but not when I looked at the printer from my machine (that is looking at the print queue from her machine shows the jobs, but looking at it from mine shows no jobs).Nothing I did would result in stuff from her machine, from any application, to go to the printer.I finally deleted the printer from her machine, figuring I'd just add it back.I try adding a printer to the laptop, it doesn't find the printer on the list of available printers. When I try adding it by typing the name - \mywin7canon ip4800 series - that fails.When I look at "network" from her laptop, my computer shows up, but if I click on it, Windows says it can't connect.
When I type ping her_computer from a DOS box, it can't find it - but when I type ping any_other_computer it finds those.Her laptop can get on the internet from our home wireless network. All the other computers in the house - Windows 7 and XP - can access shared files on my PC, and more importantly, print across the network to my USB printer.Please, patiently and precisely, guide me through stuff to check on my PC and her laptop, to get this working again. I've been through the network and sharing center on my PC and the settings are correct.Again, as it is right now, my printer is not defined on her laptop.Final, cro-magnon- level question here: If I did a system restore on her laptop, back to a point when it had been able to print, might that fix things?
Is it possible with the non-Windows 7 machine's shares set to something besides "guest access allowed"? I've tried a few tweaks on my Windows 7 desktop and my Kubuntu 11.04 Linux-running laptop. Nothing has worked. Unless access to a shared directory is set to guest on the laptop, the Windows box keeps asking for a legitimate password, whenever I attempt to 'open' them.
Both machines have the same log-in strings for both basic log-on and Samba. Or do they? I'm presuming there's no separate logon/password required for Windows 7 Home Premium when it comes to file sharing, but as a late Windows XP Professional user (both SP2 and SP3), I'm not taking anything wholly for granted. Any Windows build since the dawn of XP that installs without gpedit.msc is bound to be lacking in other ways, imco.
I have an intermittent problem with networking my desktop machine to my laptop. Sometimes after I hibernate my laptop and then wake it up, I am unable to access my shared drives on my laptop from my desktop. I am always able to go the other way (access shared drives on desktop from laptop. When it does this, even reboots of both machines don't help.
I just asked Windows 7 to diagnose and I get this. Usually after "messing" with the network settings, log offs, reboots, who knows, it usually starts working both ways again until some later hibernation restart of laptop. I wish I could pinpoint some common things that cause it but I just can't figure it out. Any ideas?
5 month old Dell XPS 8500 Win 7 64 bit Pro as main computer connected by Wired Adapter, Upgraded Gateway 5632E also running Win 7 64 bit pro as second connected by Wireless. Both running Kapersky successfully. no network problems for 5 mo.
Both were successfully linked using homegroup. Had to take Gateway to a remote location to do a business demo. While there had to link to a local public WiFi. While connecting made mistake and left homegroup.
When Gateway returned to homebase a few days later it was fine, had no problems finding wireless but could not see or rejoin Dell machine homegroup. It would let me set up a new homegroup.
Went to Dell box and found 1) homegroup no longer existed, 2) router and network and wireless printing no longer found - Red X on the taskbar) even though internet was still working fine.
Took nearly a week of trying differernt fixes, on adapter- off adapter- different adapter reboot network, router, even updated router firmware (Yes I went through every ipconfig reset, renew, redecorate etc. I've used netsh functions to try to get evrything to reset. Changes services.msc settings per other posts. Finally in desperation, deleted every sub key in the registry related to network locational awareness and got the Dell to find the network, let me set it up as a "home" network and then even see the invitation to join the Gateway's homegroup.
Then I hit a wall- when I try to join- Win 7 says I can't join the homegroup because the network is not a "home network". Of course troubleshooting is useless and goes into an endless loop. Have searched in desperation for any way to make Win 7 return to a clean slate so it can sense that it really is on a home network without success. Applied the fix-it and hotpatch for when Win 7 gets stuck in public mode. No joy. Deleted the hide wizard subkey as suggested elsewhere. No Joy. Gut feeling says problem must lie in the NLA or peer networking somewhere but where?
Does anyone know of a method or set of steps (short of a clean reinstall of Win 7) to completely clear every thing the OS knows about my network and force it to acknowlege my network is a home network? Is there a registry hack that will clear the problem?
I know I could abandon the homegroup and do conventional file/print share but I am concerned that using that solution won't last as whatever is screwing up the homegroup could eventually screw regular sharing and then I'm back to reformating/reinstalling. I'm just about ready to join the Apple folks so I never have to work on Windows again.
This sounds really noobie of me but is it possible to improve local network transfer speed by adding a 2nd network card. I was planning to connect one exclusively for lan transfers and another one hooked to a separate wireless router.
Right now only a maximum of 3 users can stream SD videos off the PC before it gets a little choppy.
The pc in question runs on windows 7 and it's board has built in gigabit, I happen to have a spare gigabit card.
So, I had to send my original schoolcomputer in for repairing. My, very rude, I might add, IT-staff at school did not include local admin for the temporary computer. I did try to ask him for local admin, as I need to change certain network-settings in order for my update my network-drivers.When asking the IT-staff for local admin, reasoning with the fact that I cannot access the internet properly due to the drivers not being uptodate, they simply wrote me off, saying that I didn't need it. They did, however, challenge me get local admin, claiming that they wouldn't care as long as I didn't cause any harm to the computer.I have a normal local user, connected to the schooldomain. It is still connected to the domain-name after leaving the schoolnetwork, where my username is DOMAIN\username. I am not able to access BIOS, do any changes in group policy or system32, and naturally, all the CMD-commands we did at junior high when we were twelve does not work. The BIOS is set to automatically boot from the HDD; thus any tricks involving .iso files and CD/USB-drives will not work.
I will cut straigh to the point! I am wondering if it's possible to set up a VPN to connect to a PC on another network so i can access the other machines on that network. e.g If I have an office with a router and 1 pc connected to the internet and 4 more machines conected to the router but not going out to the internet. Is it possible to connect to that machine via VPN so then it would be as if you were on that network to then be able to access the PC's on the network?