System is RAID 0 with 4 hard drives, I want to put in new/faster HDs. I thought all I'll need to do is copy system with Nortons Ghost, replace the drives, install the Ghost disc and reboot, is this true?
Do I need to cpoy the bios info. before HD replacement and then after replacement go back into the bios and re-enter all the info as it was before I swapped HDs.
Last night I switch over to the HD that W7 is on. It has windows updates ready to install. I have it set to notify. I clk OK and walk away. BIG mistake. I check it and there is a screen, not a window, the whole screen is black and running through commands of DEL.... I didn't write the whole line down. Just didn't know what to do. I couldn't get out of the screen. I hit restart. I didn't know what I had on my hands. A virus? It starts up fine (W7). But I get a message that chk dsk and so-so didn't finish. So I figure if its a virus I have to format anyway. I let it go through the motions. It deleted some files, it recovered some files, and in the end gave a screen with all the data about what it did, just like chk dsk and error chking does. Looked real. W7 loads fine so I figure it was OK. Today I start up the other HD with XP on it and I get two reeor messages saying that it can't find a couple .DLL's. ODBC32.DLL and MSGINA.DLL. I figure I can down load these and stick them back in. I start up W7 and can see the drive that XP is on, go to the system folder and there is no files in it. I'm pretty sure that a system folder that is empty is going to be a problem
And that was the only thing I did when I started W7.
My Dell 1525 Windows 7 laptop had begun to experience more and more frequent hard drive errors. So, in an effort to fend off total disaster, I purchased a new hard drive. The new drive was slightly larger than the old one (250GB vs 160GB). With a week old backup in hand, I used Acronis to do a disk CLONE to the new drive in an external enclosure. I was able to do it without any apparent drive errors. I then swapped drive for drive and rebooted. My most frequent apps worked fine, network access was fine, etc. Then I went to do a Windows Update - not fine. The little shield in the upper left corner of the box was red and, when I clicked on the "Check for Updates" box, it replied Windows Update cannot check for updates because the service is not running. You may need to restart your computer." I went to Services, started the service, marked it Automatic, and tried again - no joy. So, as it suggested, I rebooted. No joy again. After trying a couple of different backup versions with the same result. I went back to square one and used the original Windows 7 install disk. The install went fine and I was able to use Windows Update successfully. I hoped that having verified that a vanilla Windows 7 worked, I might be lucky enough to just be able to restore my latest backup. Wrong. The system appears to work fine with the only KNOWN problem being Update - there may be other problems, as yet unknown. Differences I am aware of: new hardware partitions proportionally larger than the previous disk.
View 3 Replies View RelatedWhat all is involved in loading Windows 7 on a new, blank drive from an Update disk?'ve got 2 computers to upgrade and am about to build a third one, so I'd like to get the Family Pack, which has retail licenses instead of OEM, but how hard will it be to use that on the new pc build?
View 5 Replies View RelatedI have a Maxtor 500GB stand alone hard drive which I originally bought for a Vista laptop, but have also been using it on my new Windows 7 laptop.It has been absolutely fine for the 6 months that I've been on Windows 7, but today Windows Update decided that I needed 27 (count 'em!) updates to be installed an run - mostly for MS Office.
View 9 Replies View RelatedI have a hard drive I want to backup to a 64gb flash drive and then restore it to another different hard drive than where it came from. I have windows 7 and office on my laptop and I want it on my desktop pc. There isn't close to 64gb of info on my laptop so it should be fine even though the hard drive says I have 160gb. It is all free space except for those programs.
View 3 Replies View RelatedSo, I have a i7 2600K system with a solid state disk as the boot drive, and an older (c2008) Samsung Spinpoint F3 500GB drive as the data drive for programs (that I deem as not worthy of the quick load times). The hard drive has given me some errors over time, and I bought a hard disk to replace it (a Hitachi 1TB). The issue I'm having is that the fact that Windows 7 puts a small (100MB) partition on the F3, and for some reason, even though I'm running Acronis 2012, it doesn't seem to be able to clone the F3 over to the Hitachi. I've also tried Drive XML, and for my 2 hour wait, I only managed to acquire a boot error. Thankfully, I've not done anything rash to destroy the data on the F3, but given the fact that I've seen corrupted files in Steam from that drive, I'm not will to trust it long term with my data. I really need to get the data onto that Hitachi, though... Anyone have any advice for upgrading the HDD in a SSD/HDD system? I don't really feel like it should be so hard, especially if I've bought Acronis True Image, but maybe they haven't designed their product to handle this scenario quite yet?
View 9 Replies View RelatedI have a HP Touchsmart IQ500. Turning my computer PC on today, all I got was a blue HP invent screen with setup, boot menu, system recovery, and system diagnosis, and I could not get past it. I entered the BIOS and figured out that the hard drive was listed as "not installed." Pretty sure that is the main problem.I tried a system restore (with the Windows 7 install disc), but I guess the computer couldn't read the hard drive enough to enter safe mode (I tried restarting and F8ing several times). I put in an external hard drive, and the BIOS read it; however, windows does not allow you to partition an OS on a hard drive.
View 2 Replies View RelatedI have an internal hard disk not in use ,and I would like to make it as external disk !I looked on the net and I found I should have the " encelsure " butt I think I wont find it here in my city .So is there another way ? like usb -esata cable
View 3 Replies View RelatedMe and my brother built me a new computer from scratch (he did the building - i did the watching). I purchased an internal hard drive from Overclockers UK. It's a Samsung 1TB drive. I also have a 64 Solid-state drive in there as my primary hard drive that Windows was installed on and a couple of programs are installed on. My storage disk (the 1TB disk) is for all my music/films etc. Whenever I drag and drop a file into the Samsung hard-drive - it copies it rather than moves it instantly.When I had a laptop, I had 3 external hard drives and this is the way it copied files onto them.how I can get the internal drive to stop acting like an external drive?
View 6 Replies View RelatedI have a virus infected sata hard drive with windows 7 on it. It has the win 7 anti virus 2012 on it, and it's a cybercriminal virus. I have lots of files I want to transfer to the new sata drive. I already have windows 7 installed on the new drive. How do I get the files from the bad drive to the new one?
View 4 Replies View RelatedI have a USB Webcam 6.1.7601.17514 from Microsoft installed on a Fujitsu Laptop (Windows 7 ) and I want to copy and install it on another Fujitsu laptop (Windows 7).The other laptop the camera is not working and there is no webcam driver installed.
View 1 Replies View RelatedI have Vista installed on my Hard Drive, 250 GB.
But i recently purchased a 2nd Hard Drive, 500 GB, and i want to install Windows 7 on it.
Is that possible, to have both separately?
make a dualboot comp by adding windows XP to a new partition. I created the new partition with 20gb. (From the 500 of my actual harddrive)But before I actually installed on that, I got distracted with a second harddrive that my dad got(for no reason). It had a full copy of Windows XP backed up on it from another computer, so I figured I would just use that for the dualboot. I plugged it in (wired the same way as my old harddrive, but different data slot), restarted, checked the harddrive in explorer - all the data was there / reading correctly / etc, and I used 'easyBCD' to add the new harddrive to the boot list.(Which, of course, crashes if I try to start it. I just wanted to see what it would do). For a reason I can't remember, I unplugged the second harddrive for a bit, started the computer on accident (I don't know if anything loaded before I shut it off), and then when I plugged it back in.Windows 7 would not launch. It goes to a DOS-like window, except it's just a flashing _ and it never does anything even after a few minutes. XP didn't work still.. so I decided to reinstall XP (as I couldn't tell which harddrive was which on the list, I unplugged the main harddrive while installing onto the new).. and when I did this.. it formatted and installed fully... then restarted.. then restarted.. and restarted.. and just kept restarting, never showing any thing past the manufacturer logo/BIOS load-button-message-thing. So, I then try to use my 3-disk Windows7Recovery disk(burned myself with a program apparently included by the manufacturer.) It installed fully, appearing to work.. but when I launched it, it said "Invalid Partition Table" and wouldn't boot past that. When I insert my driver installer disk, it gives me a basic DOS window thing. dir A: shows the files in the disk. dir B: for some reason shows the same. C: says "Error reading from drive C: DOS area: general failure". All other letter:'s just say "invalid drive". (I'm doing this with both harddrives in.) I attempted connecting the harddrives to an old computer, but it gave an error for both. (It detected the harddrives, but said it had an error reading from it. Windows Explorer asked me to format it... {i'm willing to format one of the drives if anybody thinks it will help, but the old harddrive has data I'd prefer not to lose.} ) Looking on google, I saw several problems that all have similar problems (less overdescripptive than I am though) but none of the fixes suggested worked for me. Also - as I have two different with different errors, I only need to make one of them work.)Also - my other available computer has a CD burner / floppy drive if either are required. I also have several USB's. The computer can boot from USB's and CD's (tested), and I could easily take the floppy thingy and connect it to the computer.also - this computer is probably still under warranty unless unscrewing the hard drive voids it. .. does that count as modification of the computer?
View 5 Replies View RelatedI have a USB external hard drive that I keep all my documents etc on (had it for years)I upgraded from Vista Home to & Home Premium then had to upgrade recently to Professional to run my Sage. Through all these upgrades my ext. drive ran fine. Occasionally the drvie letter would change if I had something else plugged into the USB, this was always easily corected in disk management by changing the drive path.The connection on the case packed up so I had to get the drive put into a new case, now when I plug it in the drive is assigned G instead of F, I tried to change the drive letter allocation in Disk Management but it won't let me as the program still thinks I have a second ext. hard drive which is labelled F. I suspect this has happened because when the usb connection broke the drive was disconnected suddenly instead of a proper eject.How do I get Disk Management to remove the inactive drive - i can't find any obvious way - eject, delete etc are all missing when I click on tools or tasks.
View 2 Replies View RelatedI installed Ubuntu on my computer a few months ago and created another partition for it on my 1TB hard drive. I didn't really care for Ubuntu so I decided to delete the partition it was on. That might have been a mistake. Well, now there's 87.68GB of free space on my hard disk that I can't use and I don't know how to add it back to my c: partition.
There was another post about this a couple years ago, but I don't understand the instructions and am not actually sure if it worked. Can someone explain how to do this, please? I'm not completely computer illiterate, but I'm not familiar with partitioning disks. It was just the one time with Ubuntu.
My laptop is Acer with Windows 7 home premium 64 bit OS. It contain only 1 single partition disk that is c drive only.Recently, i accidentally convert the c drive which contain OS into dynamic disk.After i restart the laptop, it shows the following: BootMgr is missing Please press Alt, Ctrl +del to restart Now, i not able to enter the window. I am so worry because my important data is kept inside the hard disk, and i still not yet do any back up copy on it.I searching on this forum and learnt that i need a window 7 installation disk to repair it, but my problem is the computer dealer not give me any windows 7 installation disk when i baught this laptop as their said all the driver and windows program already kept in side the harddisk.I tried to remove the laptop hardisk which is a 500GB toshiba SATA hardisk. Then, i use the other laptop with Windows XP professional with the intention to copy yhe file inside the toshiba hard disk.However, after plugged in the hard disk to the other laptop, under the disk management, it shows that the toshiba disk as : dynamic disk, unreadable.i having problem to backup the data inside the toshiba hard disk.....
View 8 Replies View RelatedI've been noticing after re-installing Win 7 that I get random floppy drive seeks and the hard drive light flashes like crazy and then everything is fine again.I have Clamwin AV,Spyware Blaster and Spybot S&D installed,but that's it,no Windows Defender or Essentials AV.Any ideas what causes this? It's a minor annoyance,but I just want to make sure it's not damaging anything.Also would Readyboost help me? I've got 2 gigs dual channel PC3200 ram(or I could go with 2.5 gig single channel PC2700)and a P4 at 3 gig until I can afford to upgrade my comp.This is my first post in quite awhile so I hope this is in the right place
View 7 Replies View RelatedI installed Ubuntu on my computer a few months ago and created another partition for it on my 1TB hard drive.
I didn't really care for Ubuntu so I decided to delete the partition it was on. That might have been a mistake. Well, now there's 87.68GB of free space on my hard disk that I can't use and I don't know how to add it back to my c: partition.
There was another post about this a couple years ago, but I don't understand the instructions and am not actually sure if it worked.
Low disk space, Can transfer data on D drive to an external hard drive
View 5 Replies View RelatedAlmost new Inspiron 5720- Home Premium. i7 quad.
After installing three or four updates yesterday my laptop now clicks the optical drive a couple of times as I start any video or music file on the hard drive. Not a fatal flaw, but, very irritating just the same. Did a system restore to the morning before the updates- same behavior remains. Installed updates again, removed them one at a time, same thing. Restored to over a week ago, same behavior! What is up with this clicking. The files start and play immediately, no problem there, I'd just like the optical drive to mind it's own business. Movie discs play fine, burns stuff fine, just go to your corner and SHUT UP!
I'm planning on buying an Asus Zenbook UX32VD soon and it comes with a standard 7200 rpm drive instead of an SSD. So because of that i want to upgrade it to an SSD drive.But I also want to have the same windows thats installed moved over to the new drive. The drives i've looked at all have data migration tools and one comes with norton ghost but i've never had to do something like this before where i didn't have an optical drive and a windows disk for a reinstall so i'm looking for some help here before i order everything and then do something stupid.i don't mind if i have to lose whatever settings and data i might have setup already, but i just want to make sure i have the same windows and the additions it comes with moved over to the new SSD drive.
View 9 Replies View RelatedI just started having an issue on a clean install of Windows 7 SP1 build 7601.The icons for the W & Z partitions is suddenly showing as a broken link.I have tried right clicking on each partition > properties > customize > restore default folder picture and there is no change for either to update the icon.
View 2 Replies View RelatedIs it possible and feasible to change the hard drive to a solid state drive on a Toshiba Satellite Pro L300-1FK laptop.
View 5 Replies View RelatedI have tried numerous times on my PC to install Windows 7 onto my Sata Drive to no avail. Yet as soon as I plug in my IDE HD it installs fine.I have unplugged all external peripherals USB and internal Card Reader. Set my Bios ok as it sees both the Hard Drive and DVD fine (Both in the bios and during selection of hard drive during windows 7 installation). Yet when I come to install it, it craps out at a random percentage saying cannot read from source or worse yet it crawls so slow through the percentages (I really don't think Windows 7 should take 6 hours to get to 15%!!) Yet both the hard drive and dvd are fine and the disc works great on my other PC without the sata drive in.
My motherboard is a Biostar G31-M7 TE with latest bios now what is odd is that I recently updated the BIOS to the latest one so does my problem come from here or was it always going to be a problem on this board? Also when I do have Windows 7 installed on the IDE drive when I plug in ther sata drive inside the whole system goes belly up (from freezes when transferring large files to just not seeing the drive)
I can see my external hard drive in device manager, but not in my comp
View 3 Replies View Relatedhad installed a second hard drive (seagate) sata and was installing windoews 7. I went away while the install was going on and came back to a computer that would not boot. tried the cdrom/dvd with linux live and got to linux mint 11.10 and then the compute just crashed and now, nothing even after a cmos short. cd and drives show on splash screen, but cd does not start to load. all i hear is a tick repeatedly. tried a disconnect of the cd/dvd drive and nothing.
View 2 Replies View RelatedI have an Alienware M14x R1 with a SSD - Crucial M4 in the main spot and the stock HD in the optical drive. I have never had any issues with any of this stuff before this clean install - and I have done clean installs previously. I also used Parted Magic to Secure Erase my SSD and HD before install.I am experiencing some pretty frustrating problems:
1. I have NO INTERNET CONNECTION (everyone keeps telling me to install drivers...how can I do this without internet connection??)
2. Windows is not recognizing my second hard drive in the optical drive even though it did when I was installing and showed it at the section where you can add new partitions etc
3. My display adpater is not working as I have a 1600x900 screen and I can only go up to 1024x768...
i have a (spinning) hard-drive with my windows 7system and data on it. it is up to date to this month. the hard-drive is a 320gb. there is jsut 69gb used on the 320gb.i just bought a 256 gb SSD (solid state HD). i would like to place everything on the 256 and put IT in my laptop. i have saved a system image of the 320gb on DVD. windows seems to want an exact size (320gb) to restore the system to.
View 10 Replies View RelatedMy 160 GB Win7 drive on my laptop failed (single partition), but thankfully I had a backup that I created on a 750 GB drive using EASUS Partition Master COPY. The backup drive is FULLY BOOTABLE, I've been booting into Windows 7 from an eSata external interface with no issues. It has a partition with my backed up Win7 installation and the rest is just unallocated space.
View 1 Replies View RelatedMy hard drive has been split to C and D. Im running out of space in C but have heaps still in D. Can I go back to just having one drive. C. There are files on both drives.
View 3 Replies View Related