Getting 80070570 Error And Windows 7 Install Fails
Mar 17, 2010
I'm having problems installing Windows 7 on my new PC. I just build the computer using these parts... Not sure if that matters, but there it is. I have set up the two 500GB HDDs in a RAID-0 (the install can see the drive, so I do not think that is the problem). I purchased an upgrade version on Windows 7 Professional 64 bit through a cheaper-than-dirt college program (only $30. And yes, it is legitimate.) This gave me an ISO image which I burned to a DVD.
I am trying to do a clean install of Windows 7 as the first and only OS on my new system. For whatever reason, when I try to do the install, I get a 80070570 error and the install fails (at around 5% into the "Expanding WindowsFiles" stage). I assumed, with the aid of some other forum topics, that this was likely due to a bad DVD burn... so I made a bootable Flash drive and tried that... same thing.
Clean install, I get error 0X80070570 while unpacking at 14%. Did memory test all is good. Used this dvd on another machine and worked fine. Also tryed everything I have found on the subject in forums with no luck so far.
I know there are lots of these problems here but I thinkmine is different.I have a file on an external HD that I can not delete, as it gives the above error. I use the external HD formy backups.Running Windows 7 pro 32-bit with all the goodies.I know I could format the HD to solve the error but I
I purchased the Home Premium version of Windows 7 from TigerDirect.com; I don't know enough to download the installation! I have tried everything I know (which admittedly is next to nothing) and keep getting the above error message when installation reaches the part where it's unpacking/expanding the files. I'm upgrading from Vista, uninstalled all the recommended programs to be removed before installing Windows 7 and I still keep getting that error message.
I'm working on a client's laptop, compaq Presario CQ57, 2gb ram 250 GB HDD.
I installed a new harddrive and installed a new copy of Win 7 Home Premuim x64 After it reboots, it just hangs in the welcome screen with the Windows logo.
I reboot via Windows 7 repair disc and run C: chkdsk /r and I get this message "disc check error 766f6c756d652e63 3f1"
I have tried to install this update six times today (07/05/12) after it was flagged as an important update this morning. Looking at my update history it also failed to instal on the 18th October last year but it has not bothered me since and i have not noticed it until now. Of the seven attempts I had the following error codes from earliest to latest : 800B0100, 80246007, 80010108, 8024200D, 8024200D, 8024200D, 8024200D. I have followed advice from MS running KB947821 and FIX IT also disabled my Norton 360 firewalls and auto protect but to no avail. Also I do not have a DVD with Windows 7 as it was not supplied with my PC and I don't want to restore my computer and lose all my installed software.
Windows Update installation of Win7 SP1 (updating existing version of 6.1.7600.16385) reports the install as successful until reboot, then says successful and unsuccessful in the same dialog box. Error ID is 80242016. Subsequent run of windows update shows SP1 not installed. Problem repeats, even after following all steps in troubleshooting, including running the recommended hot fix for KB 947821, troubleshooting, & turning off anti-virus. Also, the windows update troubleshooter identifies my system as AMD64 architecture even though it is Intel I7 2600K. System infomation id's the CPU correctly. System MB is ASUS P8P67 PRO, 16GB memory, AMD Radeon HD 6800 Series video card.
Tech Support Guy System Info Utility version 1.0.0.2 OS Version: Microsoft Windows 7 Professional, 64 bit Processor: Intel(R) Core(TM) i7-2600K CPU @ 3.40GHz, Intel64 Family 6 Model 42
After I tried to make a dual boot with Ubuntu and Windows 7 Ultimate (64-bit), Windows now does not boot. I have tried to reinstall and repair the HDD but the disc fails to recognize my HDD (Western Digital Scorpio Black 500 GB). My HDD is Basic, has 3 primary partitions and 1 extended (3 logical). Ubuntu 11.10 can boot fine.
I have an OLD computer with a 2.4 GHz processor and 1 GB ram, running XP 32 bit. I wanted to upgrade to Windows 7, So I tried to install 32 bit windows 7, knowing my computer couldn't handle 64 bit. However, at the end, it simply told me "Installation Failed" and reverted to XP, with all my files. I tried multiple times, then I tried installing 64 bit windows 7, and surprisingly, it worked. However, it is laggy beyond belief, so I tried installing 32 bit again. Again the installation failed. Now I'm thinking of reverting BACK to XP.
I recently built a new computer and on occasion when I turn the computer on, I'll get a blue screen saying windows failed to load type thing, and then it restarts and i have to recover. Now the weird thing is it doesn't happen all the time It more often than not doesn't work, but still there will be times where it works all day. I can't figure out why it works sometimes and not others. I don't do anything different, just facebook and Star Wars the Old Republic, so I don't think its a program which is causing the issue. Anyway here are my comp specs and the problem details:
Intel i5 2500 3.30GHz Gigabyte GTX560OC C/Master Extreme 700W WD 1TB Black Gigabyte GA-Z68AP-D3 LG DWDRW 8GB of RAM
Now the problem Problem signature: Problem Event Name: BlueScreen OS Version: 6.1.7601.2.1.0.768.3 Locale ID: 3081
Additional information about the problem: BCCode: 6b BCP1: 0000000000000000 BCP2: 0000000000000000 BCP3: 0000000000000000 BCP4: 0000000000000000 OS Version: 6_1_7601 Service Pack: 1_0 Product: 768_1
excess ie9 crashes prompted me to attempt a fix, i uninstalled ie9, updated the ie8 that was left after a restart, had the ie9 downloaded, after updating ie8 fully, tried to reinstall ie9, but installation aborted with Troubleshoot problems when you cannot install Internet Explorer 9 as my only recourse. i tried the fixit wizard, which just deleted adobe flash, but gave the same error message, and on rerunning it, said there were no errors to fix, so now i'm using firefox, ie8?
Running Vista Home Premium X64 and trying to install Windows 7 Home Premium X64. The install fails the installer's compatibility test with the message "The following issues are preventing Windows from upgrading.Cancel the upgrade, complete each task, and then restart the upgrade to continue. For these items, make the following changes:Uninstall these programs. Open Control Panel and search for "uninstall a program". Trend Micro Internet Security 2008 ".However, Trend Micro Internet Security was uninstalled from this computer at least a year ago and I can find no evidence of any shreds of it being present - not in the programs list, not in the file system and not in the registry.
I did a full back up using Acronus and ever since I have had problems. I tried reinstalling win 7, but this is what I get:"The computer restarted inexpectedly or encountered an expected error. Windows installtion cannot proceed. Click "OK" to restart the computer, and then restart the installation"I have done this repeatedly. I must add that I had a local TigerDirect store run full diagnostics and they say all my hardware is fine?
i have a hp pc with vista 64 ultimate. It crashed I believe from malware. The recovery disk suggested this was not the same pc and I'm a crook. I did change hd and a long time ago the MB due to video failure, but I've used recovery since then a couple times. This time I did disconnect the MB battery. HP support was glad to sell me a new one since my $2000 duo core 2 was obsolete. Funny you still can get duo core 2's. With much regret I bought a win 7 os and Wow the pc does work with no real issues. On the outside chance it fails after I activate and I can someway prove this, can win 7 be installed in new pc?
I've searched forum threads & online info extensively and tried everything I could think of before posting, but haven't been able to solve this issue. I recently did a new build, including:
MB: ASRock N68-VS3 UCC CPU: AMD Phenom II 965e black edition graphics: Radeon HD 4850 RAM: 2x4Gb Crucial (Micron) DDR3 1333Mhz Power supply: Seasonic SS500-HT (500 watts) Case: Antec P180B Drives: Samsung SP1614 Seagate ST3160023AS, both 160Gb
I installed Win7 ultimate x64. Installation was smooth, and everything worked, but was much more sluggish than I expected. Running a diagnostic, I found the CPU was running at 800 Mhz rather than 3400 Mhz.This was the first time I'd done a build, so I'd missed that the ASRock board supports the Phenom II line, but didn't have enough power for this CPU.So I swapped out the motherboard and installed an MSI 760GM-P34(FX).When I did the Win7 install, it proceeded through all steps to part way through the final "completing installation." It does a successful restart, and completes "Setup is updating registry settings" and "Starting services." It then does another restart.The windows splash screen comes up, but instead of starting up it goes to a black screen for a minute or so, then restarts, shows the splash screen, goes to black screen, etc. After trying a number of fixes, I posted on the MSI forum. A moderator there told me that even though the MSI web site says the board supports 125 watt CPUs, he has found that under load it would cause instability issues for a 125 watt CPU.So once again I swapped out the board and now have an Asus M5a97 R2.0, which supplies 140 watts, which should be enough for my 125 watt CPU.When I did the install, exactly the same sequence followed, the black screen at the same point in the install.Here's the kicker: in order to get more information, I tried an install with an old XP disk I had around. It installed with no issues, and has been running a variety of tasks including gaming for a week now.Everything looks good in the bios: 4 cores running, 3400Mhz, temps low, voltages from power supply look ok, memory & drives are present.
Here's what I've done:
--run Windows disk repair utility from install disk. It says Windows has booted properly.
--boot into Safe mode. It says installation is not complete, and I have to restart normally.
--remove second hard drive.
--remove second stick of ram, try booting on each individually.
--run Memtest 86 v.3.5b: 2 passes on each stick of ram individually, then with both installed. It found no errors.
--run Windows memory diagnostic, which also found no errors.
--change sata mode from AHCI to IDE
--installed XP on each hard drive without issues.
--download a fresh copy of Windows 7 x64 from Digital River, burn & install. Exact same problem.
--turn off everything in bios, including all usb, power management, lan controller, etc.
Using the tutorial at Repair Install I am attempting to repair Windows 7 Professional but at step 6 A) of the tutorial the following message is displayedWindows could not update the installation files. To install Windows, close Setup and restart the installation. Error code 0x0I wohow to proceed as I believe I have complied with the the steps thus far as set out in the tutorial
I have put together a new computer and went to install windows. Boot off the cd, everything is fine. New drive (64gb SSD for the OS) so the partitions are the 100mb windows boot partition and the remaining space for the OS, everything is fine. It starts copying and expanding files, everything is fine. Then i get to "Windows needs to restart to complete the install", ok, no problem, computer shuts down and restarts."Windows did not shut down successfully.... I select Start normally.tarting windows, pretty logo,Setup recovered from an unexpected shutdown select on option"... Safe mode, command prompt, "Setup is starting servuices"Then "the computer restarted unexpectedly or encountered an unexpected error. Windows installation cannot proceed. To install windows, click OK to restart the computer and then restart the installation."
I am having difficulties with updating Windows 7 on my laptop MSI FX603. Windows 7 came loaded with the laptop, though I do not know if I have windows 7 basic, premium, pro or else.I went on vacations in July, came back in August and I had a bunch of updates. I updated everything at once but I have 8 update files that fail to install from which only 1 error fail to update occur in the update history; therefore I assume this particular error prevents other updates to install correctly.
Update for Windows 7 for x64 based systems (KB2732500) installation date: 8/29/2012 You may need to restart your computer for this update to take effect. Installation status: Failed Error details: code 80071A90 Update type: Recommended
The knowledge base has several links, I tried all of them. 1 of these knowledge base is about downloading a windows 7 little program called "fixit" but after several attempts, I concluded Fixit cannot solve my issue or is not the proper way to solve my issue.The whole updating package files is roughly around 39 megs and I wonder if Windows 7 actually download the packages every time I click on Update or if Windows stores the updates ready to be installed somewhere on my HDD in which case I would need to re-download the update but I do not know how?
I was just installing windows 7 from bootable USB when I noticed the "copying windows files" only lasts for about 2 seconds (jumping from 0 to 100% in the process) before continuing to the next step. The whole setup process actually finishes without a problem. But the result is only about 5GB of usage of the hard drive and no creation of the 100MB system partition. I thought it might be the new SSD I'm installing it to so I tried installing on another hard drive, didn't work either.
7 Ultimate on a Lenovo computer, 8 mb RAM, Q8200 CPU. Recently I started getting notifications that my backup failed because the system cannot find the file specified, and the above error code. I'm not specifying any files, and I've reset backup to its default settings, all to no avail. I'm backing up to an external USB hard drive. In fact I bought a new one because I thought the old one was too small
Last week both my hard drives failed and after buying a new one I reinstalled Windows 7 Home Premium. When I tried to reinstall/set up Windows Media Center the set up got to the point where it was scanning my TV signals for channels and was about 1/3 to 1/2 through when the computer killed itself and rebooted. This happened 3 times at about the same place. Why is this happening and how do I get the set up to complete? I had it working just fine before on my old hard drive but I can't now.. I am now using Total Media 3.5 which works but not as well as Media Center so I would really like to get the set up to complete...
Any attempt to download and install this tool results in " This file does not have a program associated with it for performing this action. Please install a program or, if one is installed, create an association in the Default Programs control panel."
I do not get this error with any other program I attempt to run, or download and install. I need to create a bootable usb drive or dvd to do a upgrade repair of my 7 installation. My original windows 7 DVD does not contain SP1. I have downloaded the SP1 iso and just need this too to work.
I can't install Windows Live. The installer keeps rolling everything back after 99% of the process. For the first time it failed it only installed MSN and Mail and the rest was rolled back. Since then it doesn't download the installation files any more as the old ones are stored somewhere on the disk and it uses them for the installation. Guess the problem occurs because the installation files are corrupted but how do I force the installer to download the again? Looked everywhere and can't find the place where the old installation files are stored...
Just in case, the error i'm getting after the roll back is:
'try installing win live programs again. progs were not installed because the installation was cancelled. aborted: 0x80004004'
1. Same computer in my signature/specs except for the optical drive.
2. Hardware passes Windows 7 compatibility test.
3. The install DVD can be read properly. Creating an ISO image of it works perfectly. No read errors on the disk itself.
4. The optical drive is practically brand new, the cable is brand new, never had any I/O errors using this drive.
5. RAM passes MS memory testing 6 times. 0 errors.
6. Windows 7 Ultimate install fails at the same point, during file unpacking, 3 times. Says files are missing or corrupt.
The install disk was created at home from an ISO download, student licensed Windows 7 Ultimate, 32 bit but I don't think that really matters. See #3.Is there anything else left to look at? Any ideas why this won't work?
So I have searched around and none of the solutions worked, but let me get to the basics:
DFI LanPark DK 790 FX Motherboard 3.2 GHz AMD Athlon X2 64 bit processor 4 GB DDR2 RAM Nvidia GeForce 8800 GTS Video card with 720 MB Ram
Hard drives:
Western Digital Raptor @ 70 GB (going to be used as the OS drive) Western Digital Caviar @ 80 GB
Maxtor 120 GB IDE drive (the other 2 are both SATA drives)
Sony DVD R/RW Drive using onboard audio
Okay so I am running a fresh, clean install (the only "information" is on the IDE drive, and that's my backup for iTunes and Steam) using the Windows 7 Ultimate DVD. The DVD kept hanging @ "completing installation", so I took it to my laptop, and using the instructions on here, made a bootable flash drive.I just tried completing installation from the bootable flash, and it still hangs at that step.When it hangs, it's in a locked up state.. I can't even press Shift + F10 (nothing happens). Also, the CD correctly makes the "System Allocated" section on the drive. Also, i removed all USB drives, and am running both a PS/2 mouse and keyboard.
My laptop was running windows 7 and then crashed. It was getting slower and slower, then crashed during a virus scan in safe mode. After that, it wouldn't boot up windows. It said something like disk error, press ctrl alt delete to restart. Safe mode doesn't work either. So now I'm trying to reinstall windows 7, and the installation fails when at expanding files. It says the files are corrupted and can't be installed. I've tried 3 diff windows 7 cds. It gives errors at different points during the expanding every time. Now its just hanging at expanding windows files (0%). Its been here for 20 mins so far.
I have a lop top with Windows 7 64 bit OS. Of lately, Windows update keeps failing to install some software updates. Here are the details of the s/w that would not install[CODE]
