i heve a cyber acoustics surround sound system 5150 5.1 and i only get sound out ov 2 speakers i heve dunn a test on all speakers and all ov them graft.properly? my computer is an acer aspire x-1300.
View 3 RepliesI recently reinstalled Windows 7 and have since then not been able to use my speakers correctly since. It's important you know that they worked just fine a few days ago before I reinstalled. I did of course do a full format of the hard drive. When I'm configuring the speakers in Windows to 5.1, I'm not getting any feedback from the two rear speakers.My speakers are Logitech Z5500, motherboard Asus 880G Extreme3, sound card Creative SB X-Fi XtremeGamer Fatal1ty Pro. Enabling X-Fi CMSS-3D doesn't do anything either but make the volume of the front speakers a bit lower to compensate for the supposed increased volume of the rear speakers. Which is non existent anyway.
I tried plugging the cables (I use analogue) into the on-board sound card's ports and had the same problem, which tells me it isn't a problem with the Creative sound card, but most likely something in Windows that I'm missing. Testing the speakers through the receiver works just fine. I have also tried removing the drivers I installed completely and reinstalled to see if it just was some installation error. I have also tried removing the on-board sound card drivers and disabling the on-board sound card in BIOS while trying to install the Creative drivers again. This shouldn't have worked anyway since I'm having the same problem with the two sound cards.
Hp 5150 driver sound?
View 2 Replies View RelatedI have a Dell Dimension 5150 which runs XP Home and is 3 years old. I pre-ordered Windows 7 but the Windows 7 Upgrade Advisor says my onboard graphics adapter won't support the Windows Aero User Interface. I don't play games on my PC but I would like all the fancy visual features of Windows 7. How do I go about choosing a graphics card that will do the job for me?
View 8 Replies View RelatedWhat audio device in a dell dimension 5150
View 2 Replies View Relatedget rid of this crazy software, i cannot close it anymore from my laptop
View 4 Replies View RelatedSend me driver for camera sony cyber shot vx dsc N1 8.1 M P
View 1 Replies View Relatedmy cyber-shot camera wont dowload its pictures its a DSC-S780, i have theusb lead and everything i just want to no if theres a download i can do to make it work?
View 2 Replies View RelatedMy new Dell comes with a dluted vbersion of windows 7 that does not allow the Cybershot to download the pictures. Is there a driver program available or a special way to get the caera to down load?
View 2 Replies View RelatedI would like to download a driver to be able to transfer my photos from camera to computer.Do you have a download for windows 7?
View 1 Replies View Relatedi want to download dell inspiron n 5050 webcam drivers
View 1 Replies View Relatedi recently brought sony32EX650 LED TV with Sony DVD player with home theater.and i want to watch HD movies on this TV with surround sound but we know dvd player don't play the Hd quality videos.But on TV's usb we can play those Hd videos and they have 5.1 surround sound also.and i can't get 5.1 through TV's USB. is there any possible to get 5.1 through TV's usb via home theater.
View 1 Replies View Relatedixin my surround sound
View 2 Replies View RelatedI installed SP1 for windows 7 this week and since then my sound is not working propely. Its only playing my front 2 speakers (Not rear 2 or centre on 5.1s) I have installed new drivers (Realtek) but nothing.If I run a sound test all speakers ding (on realtek or windows audio settings) Great but any application just pipes sound out to front 2 speakers. Is there another setting within windows ive missed?
View 1 Replies View RelatedSo after installing win 7 ultimate x64, 5.1 surround stopped working and now i can only use my 2 front speakers + sub. In test all speakers don't work aswell.
View 3 Replies View RelatedMy laptop is a HP Pavilion dv7-2078ca Entertainment Notebook PC
Specs here: Product Specifications*
I have my Computer hooked up to the TV through a HDMI Cable and My TV is hooked to a surround sound receiver through
red and white cables.
From Audio Out on the TV
The TV is a Toshiba 37HL57
I tried installing new Realtek and ATI drivers, but I still couldn't get the surround working.
I installed these:-
ftp://webuser:WN4Ic2i@218.210.127.133/pc/audio/HDMI_R229.exe
ftp://WebUser:DAx7h9V@66.104.77.130/pc/audio/Vista_Win7_R229.exe
https://a248.e.akamai.net/f/674/9206/0/www2.ati.com/drivers/9-7_beta_win7_64_dd_CC.exe
But working I mean, I go to control panel then sound and for HDMI is only lets me select stereo.
After some research I figured maybe its because the HDMI goes to the TV and the TV itself only has two speakers.
Still there must be a way to do this.
I can't do HDMI to the surround receiver as its a bit old
But, its seems to be surround when playing movies through VLC...
But I tried this surround test.
http://www.halfgaar.net/media/chan-id.zip
and you could defintiely tell there was "audio coming from different corners". But, when the test announced which speaker the sound should be coming out, it wasn't always accurate.
I've recently bought a SoundForce 5.1 (Trust) surround speakers set with a SC-5500P 5.1 External Sound Card. At first I didn't have the sound card so I could only insert 1 Jack 3.5mm and only 2 speakers would work at the same time.Now however with the sound card I expected them all to work together, but there's only sound coming out of 2 of them (the other emit a very low 'pshhhhhh').I've tried to configure the setting of my sound into 5.1 surround, but the test sounds only come out of two of the speakers.Do 5.1 sources play in 5.1? If so that rules out it being a 5.1 problem, and makes it that you need some kind of surround sound upmix to be done. I have no idea if there is anything like that for the audio on the Nvidia cards that have a sound card built into them. What you need to look for is some kind of speaker fill option (called Speaker Fill on Realtek, CMSS3d on Creative), or something like Dolby Digital Live (needs to be supported by the card and/or drivers, and can't be just installed as far as I know). I've found this in another thread, and tried a 5.1 wav sample. However it still only comes out of 2 speakers.
View 9 Replies View RelatedI have a system running Windows 7 64 bit and a set of Logitech z5500 speakers. Originally I was using a Creative X-Fi Titanium Fata1ity board. In XP I was able to get surround sound. When I switched to Win 7, the surround sound stopped working. Sometimes it would test as working in the sound app in the control panel and sometimes it wouldn't. Sometimes I could fix it by reinstalling the board's driver, but it always stopped again over time. Generally I had to make do with a front R/L/C system and the subwoofer.After goggling the issue extensively, I finally decided that the problem was some unidentified conflict between the Creative card and Win 7. So I researched sound cards and finally settled on an Asus Xonar ST with an H6 card. I hooked the system up via a setup that looked like the chart here: [URL]. However, now all the sound comes out of the front R/L/C--and no subwoofer!
View 3 Replies View RelatedJust found a Sharp 5.1 system in my garage. I've rigged it up, all the speakers work fine when playing the radio etc. However it only plays sounds out of one speakerIn the Speaker Configuration tab in Realtek Audio Manager HD it detects there are 5 speakers and a sub however when I click on the sub it plays sounds out two speakers and none of other ones do anything.
View 3 Replies View RelatedI have set up my surround sound 5.1 speakers recently.I went into the Realtek HD Audio Manager, and set it to use "5.1 surround sound",but as I try to play music, sound only comes through the front speakers.I have tried looking through all sorts of settings, and cant find what I could have set wrong.I have tested the rear speakers in the sound manager, and it plays sound through the rear speakers in the tests, but Itunes, and internet explorer do not play sound through the rear speakers.If I change the defult device in the second screenshot to use Realtek Digital output, no sound comes out at all.
View 4 Replies View RelatedI recently purchased a 5.1 sound system, which I have connected to the S/PDIF output on my MB (Gigabyte Guerrilla) however my system seems insistent on sticking to a 2.1 output. A quick search shows that I should go into speaker setup, find the correct playback device and reconfigure it; however when I go to this page the option to configure is greyed out so I cant use it!I have gone through the properties page and when I do the supported format tests sound is done through all connected speakers so I know they can physically receive a signal.Does anyone have ideas as to why the configure option is greyed out? I am on an administrator account and UAC is turned off.
View 4 Replies View RelatedThis error started occurring out of no where. This is the first time that my has been able to catch it. Normally the game just freezes and all three of my screens go black. Sometimes it stays there and I can here skype in the background. Other times it will completely freeze up. This only happends when I play on all three screens. If I play on 1 screen, it works nice.
View 1 Replies View Relatedmy laptop doesn't have the sound card to provide 7.1 surround sound, it does however have Dolby Surround Sound, so I was thinking if I purchased a 7.1 surround sound headset, how can I configure each speakers on it? Since currently the only audio channel I have is Stereo.The headset is plugged in by USB, so it must act like a sound card on its own, if I plug in the USB headset, will it provide me another audio channel for 7.1?
View 1 Replies View RelatedI just got some surround sound headphones. When I restart my computer after having set my sound configuration for the headphones to 7.1 (supported by these headphones) the sound configuration will be at 5.1. I don't know what is causing it to keep going to 5.1.When the set up is at 7.1 the two rear speakers are enabled. This might seem small but I play battlefield 3 and being able to better hear enemies who are behind me willter and this is one of the reasons I got the headphones so I definitely prefer these two speakers to work.
View 5 Replies View RelatedWell i have a stereo 5.1 system by Creative, version SBS 580.When i first got the computer everything was fine, then my brother bought those headphones, so we didnt use the speakers at all.so after about 1-2 years without use i plugged them in and tried to use them.The problem occured was that only the subwoofer worked, none of the speaked did,and the subwoofer only worked at the "Realtek HD Audio Manager" program.I tried reading forums of creative, tried to connect the system to the computer in many ways, all of the ways give me the same result, only the subwoofer produces sound.the way creative's guide say to connect the speakers is like that: ImageShack� - Online Photo and Video Hosting The program that im using is "Realtek HD Audio Manager" : ImageShack� - Online Photo and Video Hosting so when i play this play button, only the subwoofer makes the sound, non of the speakers. All of them are connected to the subwoofer correctly, they are turned on.
View 1 Replies View RelatedI have bought 4.1 channel surround system and I connected them to my system. But am able to hear sound coming from only from two speakers. I am using windows 7. Please provide me steps how to select 4.1 channel surround system. And also to which jacks the pins have to be connected.
View 1 Replies View RelatedWell I got some old speakers an jimmied up my own 5.1 surround, though in reality it is only quadraphonic. Is there any way I can configure my system to play sterio audio through all 4 speakers?
View 2 Replies View RelatedMy computer was blue screening. I had a warranty RMA through my manufacturer and I just got it back, fixed. However since then, my Logitech X-530 5.1 surround speakers have been messed up. Initially I thought the front two were not working, but when I was testing I found the Left Rear works and the Right Rear sound comes through the Front Left speaker. The Subwoofer is fine, but the Right Front and Rear have no sound. To be more clear, when my realtek audio manager tests the front two speakers, there is zero sound. When it checks the LR it comes through the LR fine, but the RR comes through the LF speaker. I've unplugged, checked wires, made sure everything was plugged in correctly, and I reinstalled my realtek HD audio driver also.s.
View 1 Replies View RelatedThe strand thing that it's working perfectly in AIMP3 , but when I'm playing a movie in classic media player or YT video, only the center and right speakers are workinghe others have this weeird , super low delayed sound , barely Noticeable .This is my motherboard , maybe I've downloaded wrong drivers or something, but I'm pretty sure that before reinstalling my Windows 7, I had this user friendly configuration tweak with sound options . Now it seems to be gone .
View 3 Replies View RelatedI am having trouble getting my audio from my laptop to play as 5.1 surround. I have my Laptop with a HDMI running to my Vizio E260mv TV and then a audio optical cable running into my Sony BDVE390 surround sound system. It could just be a configuration problem with my PC's audio settings or something more I am not certain,
View 2 Replies View Related I've got a bit of a problem with my audio with my new installation of Windows 7. Previously I had Vista installed, and had no problems with my Realtek HD audio. Installed Windows 7 everything looked good, then realized my Sony A/V receiver model SA-WCT100 was not outputting my movie collection in surround 5.1 like it use to using Vista.
I figured, that�s cool, probably need to install ac3filter_1_51a, I had to in Vista, and it worked a treat when I enabled SPDIF pass through. I guess I should mention I�m using HDMI all the way through, from my PC to the receiver, from the receiver to the LCD. Well, that didn't fix it, everything still plays in stereo. After scratching my head and clicking here and there, I finally found a little tab in the sound settings of my Realtek HDMI setting called 'Custom'.
I selected it, it said to enable AC3, DTS, etc click this box will require a restart. I said awesome, sounds like just what I need. I clicked, and rebooted. I went into WMC, and setup my audio wizard again, and selected 5.1, and tested, and this time it reported 5.1 on my Sony receiver as before it only showed 2 channels (Stereo). I played some of my DVD rips, and bam my DVD rips were playing surround sound again.
I was like that was easy enough. I went to test my Blu-Ray rips that I had converted to WMV HD using TMPGEnc Xpress 4.0, and the video started to play, and I was like, wheres the damn sound. I noticed on the receiver, it didn't report anything for sound. I had no idea what was going on. My surround sound was finally working for everything, but my WMV HD videos had no sound output. I mean I can't even get stereo or anything out of them now. At least before the WMV played in stereo, now I can't hear anything.
Please someone tell me what could be the problem, I don't know what else to try. I don't want to have to revert back to stereo, and disable the magic box under custom in my sound setting.
I have downloaded the latest Realtek drivers form Realtek, version 2.35 for the ATI HDMI audio, and the Digital Audio. I also have the latest drivers for my integrated Radeon 3200 graphics card. I read that sometimes a high resolution can affect the audio, so I lowered my resolution from 1080p, and that didn't help, which I figured it wouldn't.