When physically moving a HDD that was on one motherboard to a another motherboard is it recommended to back up all partitions for the HDD or just as long as you have the active windows partition HDD backed up, it doesn't matter?
View 3 RepliesIs it possible to move my Windows 7 installation from the partition (both the Sys. Reserved & OS partitions) of one drive on one controller to the partition of another drive on a different controller, AND have it boot? I know "something" would have to altered, but I'm not sure "what" or "how". Is this even possible without going through a lot of hoops. Specifically I have an installation of W7x64 installed on the 1st partition of the master drive on a PATA controller. I want to move it to the 1st partition of the master drive on my SATA controller.
FROM PATA0 {sys reserved}{OS install}{data}
TO SATA0 {sys reserved}{OS install}{data}
I also have another install on the 2nd partition of my SATA4 controller and want to move it to the 1st partition of my SATA0 controller
FROM SATA4 {data}{sys reserved}{OS install}
TO SATA0 {sys reserved}{OS install}{data}
I have a 320GB Seagate Hard Drive. It has 2 partitions and I used 1 for projects and recordings, and the other for backup. Now I have a WD Caviar Blue 500GB that I plan to use for projects and recordings. Is it possible to backup to both partitions on the Seagate hard drive? Someone on OCN told me that you can't already do it with native Windows backup.
View 9 Replies View RelatedI finally gave up on Backup My PC and went to Win 7 backup, but my external drive does not hold more than 2 backup cycles' worth of data. I'd like to use excess space (in a separate partition) on a 2 TB internal drive to offload some backups, but I can find no way of doing this.
View 1 Replies View Relatedi just bought a new computer running windows 7 home edition. my question is, can windows 7 make an entire image of my hard drive including (and this important) the recovery partition? If It can can anyone please tell me how. i need to have a complete backup of my hard drive in case of hard drive failure.
View 1 Replies View RelatedI have Asus N55SF laptop, with Windows 7 SP1 64 bit. Also, I have 2 external hard drives. One with USB 3.0, and one USB 2.0. Following problems, I am going to describe below, happen to the both of them. Just to mention, external drives are tested on desktop computer and following problems do not happen.
Let me now describe what happens when I try certain actions:
- When I try to copy large files (10 or more GB) I get an error that destination is no longer visible. External drives disappear from My Computer and I can't do safe remove. But when I copy files using programs FastCopy or TeraCopy everything copies well and drives do not disappear.
- When I try to do Windows Backup and encrypt them using BitLocker drives also disappear, and are not visible within OS.
There is a difference between external hard with USB 3.0 port and the one with 2.0 port:
- When one with 3.0 disappears after described actions I can't see it from Device Manager, I can see it only after windows reboot. USB 3.0 disk connects to one USB 3.0 port on laptop.
- When one with 2.0 port disappears I can see it from Device Manager, and I only have to unplug it, and plug it in again to see it. USB 2.0 disk connects to 2 USB 2.0 ports on laptop.
Common to both disks is that when then disappear from My computer the diode on the external disk cases are still flashing, what probably means that they have some power. Both disk are formated to NTFS, and Allocation unit size is set to: Default. Their removal policy is set to: Better performance (default). On laptop I only have Windows, Office and Asus drivers. Antivirus is: MSE.
As my Vista machine was failing I did a full system backup. I did not do a simple file backup. That machine is now dead. Now I need to move the files within the system backup to my new Windows 7 Home Premium 64 bit machine but I'm not finding any way to accomplish this.
View 2 Replies View RelatedI want to either move or restart Windows Backup to a new drive. So I'd like to wipe the current Backup off the drive it is currently on. I really don't care that much about saving older recovery points. Is there a way to just switch where the recovery is saved and once a new restore point has been created on the new drive I could just delete the old files on the other drive?
View 6 Replies View RelatedI back up my files and system image weekly. I move the recorded TV shows (broadcast TV, nothing illegal) before that from my hard drive onto an external drive. Another drive in the same cabinet does the backup. It saves time and I won't want those files after a disc failure anyway.It would be cool to be able to program the computer to move those files (but not subfolders) over at, say 11.05 pm in preparation for the midnight backup. It would be easier to put the recorded TV in a subfolder though I suppose... then no code would have to be written to ignore subfolders, right?
View 6 Replies View RelatedOne of my friends has a windows 7 computer with an account for himself, his mother and his 2 sisters. All the home directorys are stored in drive C. Partition D is shared. The question is, how to get a partition layout like this?
Partition 1: OS + programs
Partition 2: home partition for himself
Partition 3: home partition for his mother
Partition 4: home partition for his sister
Partition 5: home partition for his other sister
Partition 6: shared partition for some photos.
I created an image using the Microsoft Backup and Restore tool in Windows 7. I saved the image on a network shared folder.I then went to the Advanced Recovery Methods in Windows to restore my image...that I just created. It restarts the computer and goes into recovery mode, I point to where the image is located, I entered the network credentials and it give me an error. "The Specified network resource or device is no longer available. (0x80070037)"
View 5 Replies View RelatedAny simple backup program that is capable of backing up large files incrementally by splitting the file and backing up only changed parts of the file? The files I'm talking about are files that get altered by appending stuff at the end of the file, e.g. log files or mailbox files, so it's generally possible to split a new version of the file at the exact point where the old version stopped, purely by file size.
Specifically, I want to back up Thunderbird and SeaMonkey mailboxes without having to create additional subfolders within those programs. I understand that if something had changed near the beginning of the file, then the whole file will have to be backed up, unless the backup program is capable of some very clever searching, but mostly the files will change only by having data appended to it.
Which backup software to backup Pictures/Documents/Videos so that when you do a fresh install you don't loose anything.apart from your programs of course, just the documents backed up what do you use?
View 13 Replies View RelatedI'm running Windows 7 64x Home Premium on a Toshiba Qosmio X505 laptop. I just got it back from the warranty repair center, where they replaced the hard drive and graphics fan & heatsink, and reloaded the factory windows version. Before I sent it out for repair, I used Windows Backup to create a backup of all my files on a Toshiba casio 500GB external USB drive (I had over 300 GB of files, so it was easier to use Windows Backup than drag and drop all the files, at least at the time). Now that I have the laptop back, I'm having trouble restoring my files. When I go to Control Panel-> Backup & Restore, a message appears in the restore section, saying "Windows could not find a backup for this computer." I've tried reconnecting the drive as well as restarting my computer, but to no avail. I can see and explore the files in My Computer, so I know the hard drive is properly connected.
View 7 Replies View RelatedHow to Create a System Image Backup in Windows 7 ?
View 0 Replies View RelatedIs there way I can change the location of the backup files location using the Win7 Backup Manager? Right now it just shows me the location for a USB port. I would like to use a Home Group Location.
View 2 Replies View RelatedWhen you wish to recover your system using this utility, do you use the Windows program at desktop or the rescue disc I created from the program?The reasn I ask is because I used to have better luck using Acronis' disc rather than the program and wonderd if the same applied here.Also, does the backup remove the existing one so that you only have one at a time or can you have more than one.
View 2 Replies View RelatedIs there a way to use Windows Backup to backup to a network drive?
View 6 Replies View RelatedI backup 100GB of data with Windows Backup and over the time where I do all my backups there is like only 30GB of data which changed from those 100GB and also new files were added. Now my external drive is full. When I now delete the very early backup, the first one where the 100GB of data was saved, will it delete then ALL those 100 GB, or will it just delete the previous versions of the files which were modified AFTER that time, which are in this case the 30GB I talked about? Because otherwhise I would then have in the end an uncomplete, messed up backup.
View 9 Replies View RelatedI currently use Vista Ultimate. I am preparing to move to Windows 7. Is it possible to restore files from Vista Backup and Restore Center to Windows 7 after a clean install?
View 3 Replies View RelatedI'm using Win 7 Pro and want to schedule several backups to my NAS. With Win XP, I was able to schedule multiple backup jobs, which makes things easier since I have 116 GB of data. I like to backup my documents, email files, etc. every week, but my photos, MP3s, etc. don't change as frequently so once a month is fine for that. Not surprisingly, the media collection takes much longer to backup, which is another reason I try to separate it from my "regular" backup.Unfortunately, Win 7 backup only seems to allow one backup job to be scheduled, which seems awfully limited. Am I missing something? Are there other free backup utilities that would work better, or do I need to shell out some cash?
View 4 Replies View RelatedI'm trying to backup Windows 7 to an external HD that currently is used to backup mac.eed to do to make this happen? I'm sure I'll have to format the ext HD then backup the mac using a different file format, but am unsure just what I'll have to do or how to do it.
View 4 Replies View RelatedCurrently my PC is set just they way I like so I thought I'd do a backup, the idea being that should something go wrong then I can just use that backup (on DVD's) to do restore my PC to the 'now' settings.
View 3 Replies View RelatedDoes anyone know what would cause the following backup error?
The backup was not successful. The error is: Windows Backup encountered a problem while determining additional locations of one of the users included in backup. (0x81000038).
Windows 7 Backup always stops around 58% when it tries to backup "Boot (C" What should I do?
Windows Sicherung bleibt stehen bei 58% bei Systemabbild von "Boot (C" wird erstellt.
I am thinking of replacing my old Dell using XP, with a modern one. I partitioned the old one so the OS & programs were on one partition & documents on the other. I suppose this will not be necessary with the large hard drives available now? I don't foresee having any problems backing up the documents. What do others think?
View 9 Replies View RelatedI have two physical HDs in one of my machines. The first is C. The second physical HD has two partitions, which are D and E. This drive has failed, and I took a HD from another machine, and added it to this one we are talking about. Windows 7 sees this HD as D, because unlike the one that failed, this "new" one was originally formatted with only one partition. I would like to get Windows 7 to see this HD as D and E (and transfer files as necessary), so when I load my music template from my sequencer, it will find all of the necessary audio files.
If the second HD is only D, the template is not going to be able to find all of the files automatically, even if they are physically on the D drive - this is b/c the sequencer is looking for some of the files on E, which doesn't exist. I can browse for, and point to the the files on D, but it gets to be a PITA if I have to open eny old templates or projects. So, what I would like to do is somehow get Windows to see that second HD as D and E, instead of just D. Is there any trick that I can do to make this happen? Trying to avoid having to reformat.
I have a Win7 64-bit system and have been successfully using Windows backup on an approximately monthly basis. I ran it before going to bed last night and woke up to a "The backup failed." when I tried to create a system image of both of my hard discs. The error is "Incorrect function. (0x80070001)". I found a workaround solution at Windows backup or restore errors 0x80070001, 0x81000037, or 0x80070003 and looked up and found a number of "junction points", most rooted at c:UsersDilipAppData - but the problem is that there is no such folder.
View 9 Replies View RelatedI just partitioned my C drive and now have an I: drive that I use for data, music and movies and such.My question is this: if I have to do a system recovery. Will I lose that partition? Or will Windows 7 re-install on the C: drive without touching that partition?
View 3 Replies View RelatedThis is a 1TB HD with Win 7 pre-installed on a 100GB partition (C and a remaining 809GB or 811GB depending on what I use to look at it on a second partition, I would like to partition the remaining 811GB (D however I ran into a confusing snag. Even though Windows shows only 2 partitions,when I run my partition manager it shows that there are 4 partitions, 100MiB NTFS, 101GiB NTFS, (extended) 809.65GiB,sda5 809.65GiB NTFS.
View 9 Replies View Related.I originaly partitioned my hard drive and I dual boot with XP and 7.I would like to know how to merge the two partitions back and just use Windows7.Just remember that you are not dealing with a rocket scientest here,hope to make it as easy as possible.
View 3 Replies View Related