BSOD Only After Long Time Without Power Supply, 0x0000001E
Nov 16, 2011
If the computer is shut down and disconnected from the power supply for about 5 hours or longer I get a bluescreen right after the windows boot screen. Otherwise it starts without problems and works fine. My workaround for the problem after long shut down is to switch on the power supply, then immediately switch it off and then on again. This works always fine!
My System:
Windows 7 Home Premium 64bit SP1
AMD Phenom II X6 1090T Black Edition Asus M4A89GTD PRO/USB3 4GB (2x2) 1333-777 RAM ATI Radeon HD 5570
Blue Screen: *** STOP: 0x0000001E (0x0000000000000000, 0x0000000000000000, 0x0000000000000000, 0x0000000000000000)
I already used all of the windows debugging, diagnostic tools and Memtest but without success.
I have windows seven RC1(32 bit) and I get a BSOD when my computer works hard for longer periods of time. I do not have this problem with my vista partition. For example if I do a 30 mins skype call or play a game for 20 mins I get the BSOD. However I can surf the internet and listen to podcast for hours and have no problems.
My computer gets at least ONCE BSOD every time I turn it on after a long period of shutdown. It also sometimes randomly just shuts off or give me additional BSODs. It has got to the point that I can't even load to windows recently, which lead me to reformat my computer. I know the drivers here are not the latest ones, I am trying to use only the drivers from the CDs that came with the hardwares because the last time I used all the latest ones it still caused BSODs. I am not sure what other information I need to post up.
Windows 7 Ultimate x64 - fresh reformat ASUS M4A77TD Pro AMD Athlon II X4 635 2.9Ghz Socket AM3 95W Crucial 4GB DDR3-1333 (PC 10600) MT16JTF51264AZ-1G4H1 (It's a 2x 4GB set, but I'm just using once at the moment to filter out problems) SAPPHIRE Vapor-X Radeon HD 4850 1GB 156-bit GDDR3 Western Digital Caviar Black 640GB 7200RPM SATA Antec Trupower 650W
I'll be playing a game for about 25 minutes then it will crash and another time where it crashed is when I leave it on all night to finish steam downloads. I figure it might be the CPU or the video card but i am not too sure.
A standby machine that I have is having trouble starting. When first turned on, it will attempt a start, drive lights fans etc come on then within 3 seconds, go out and repeat. This does this for about 5-6 iterations and then starts normal and will run until turned off. This system has one HDD, one DVD drive, MB graphics, so I don't think there is much of a load.
My original problem, i am sure is my power suplly, I have just upgraded to the cross hair V main board. My computer has been restarting randomly during intensive game play. it didn't do this before my upgrade. Secondly as i have said above i currently have a 500w PSU. I am thinking of upgrading to the antec High Current Gamer 750 watt. I have filled in the system specs. do you think it will run my computer perfectly. also i will be getting 16GB DDR3 1600MHz RAM and an ATI 6970 will the antec PSU be enough?
i just bought a new gpu (Nvidia Gefore Gt 440) but it reccomends more than 400 watts, i only have 240 watts. Due to this, games lag on my new gpu. Can i overclock my power supply so i dont have to buy a new one?
I'm having some strange problems with my PSU. My computer went black last night while I was playing GTA IV. After some research on the web, I came to a conclusion that my PSU died. I attempted the paperclip trick with no success - fans didnt do anything. I was about ready to start shopping for a new one, plugged everything back into places, when I saw a red 115V/230V switch on the back. I switched it from default 115V to 230V and tried the paperclip test again. This time the fan on the back of the case (not PSU) started spinning, and lights on the front and the green light on CD-ROM lit up. I plugged the 24 pin connector back into the motherboard, and hit the on switch (still with 230V), and the same thing happened.From what I described above, what do you think has gone wrong with my PC? And why is PSU acting the way it is?
Which power supply is better for gaming? CHIEFTEC 750W PSU, 85+,230V W/CABLE MNG ( CTG-750C ) Or OCZ ZT Series 750W fully Modular 80 Plus Bronze, ATX12V v2.2 Active PFC ( OCZ-ZT750W-EU )In future i might Sli/crossfire.
I replaced my power supply and now I get a 0x80070035 error when trying to map my network storage server. I've had this mapped for over a year, and usually just need to enter the password to re-connect after a re-boot. I've tried disabling the firewall, anti-virus, file and printer sharing, etc. I looked for the extra network entries that others have said to delete, but I don't have any.
This computer is running Windows 7 Professional 64 bit. The network storage server is running Windows 7 Professional 32 bit. From the 32 bit machine the 64 bit machine shows up, even in explorer.
From the 64 bit machine the 32 bit does not show up except under the Network and sharing center, selecting "see full map" shows both machines.
I can't see how changing a power supply could cause a problem. I tried going back to a restore point from last week in case a "windows update" caused the problem, which did not show up until the latest re-boot, but that did not help either.
Why is this. Like 10 minutes plus and it still says recycling. It should only take a second. Is it bad to let it continue at its own pace or should I restart the PC and try it again?
Right I have a 550ti but only a 300w power supply. My performance is shocking on it. Is this cause my power supply? It's recommended to have a 400w +. Also my processor is only at like 70-80% use.
I am starting to think I may have a power supply issue and none of the programs I use seem to monitor it correctly or the power supply is bad. I have been using TOverclocker (came with my Biostar MB), Speccy, Everest, HWinfo64, HWinfo32 and SpeedFan. None of these give me consistent measurements or measure the voltages wrong from opening the program. Is there a monitor program out there that is very good at measuring power supply voltages. My MB is a Biostar TZ68A+.
I've got a gateway model computer I want to upgrade, but I need a 400W power supply for the card I'm buying, should I be worried about a new power supply being incompatible for any reasons with my computer?
Through a clean install I switched to Windows 7 last week. Today being the 6th day since I switched, the computer has frozen 4 times. Of the 4 times, one was just a sudden power down without a proper shutdown.
Through event viewer, the log suggested an error dealing with power supply.
Since I've noticed that multiple PCs on different processors are seeing the same error, I would like to know if there have been any fixes released for this yet.
I installed the graphics card but it needs 6 pin PCI-E auxiliary power connector, my power supply is DELL J102N PS-5361-2 360 Watt Power Supply XPS 435MT and it doesn't have this 6 pins, when i start my computer it's just giving me 6 beeps which means Video card failure. What should i do?
My brother needs a video card but me being the smart one here. I got his info from dxdiag and I need a recommendation for two things , a video card and power supply. His current power supply runs at a max of 250w and it seems low, mine being 500w so its the right thing to upgrade in order to get a video card. keep video card recommendations "single slot" only since I have no idea how to hook up a video card to a power supply. Single slot ones are simple.
System: Windows 7 Home Premium 64 bit Manufacturer : Hewlett-Packard Processor: AMD Athlon(tm) II X4 640 Processor Memory: 4096MB RAM OS Memory: 3840MB RAM Power Supply : 250W Max
Ever since I changed my power supply from an Orion 480W to my current Cooler Master power supply, my pc will not sleep. It initiates sleep but then immediately turns back on and boots to the login screen. I have tried everything! From powercfg in cmd to changing the seetings on the motherboard in bios, and disabling all hardware from waking my system up to changing the power supply settings in windows. I am considering doing a reinstall of windows
recommendations for compatible power supply & graphic card upgrades. My current model is EL1352-03 (specs from Newegg below):[URL]Is it realistic to upgrade this model due to the motherboard case & available slots?
My computer keeps shutting itself down with the following error message:
"Power surges detected during the previous power on. ASUS anti-surge was triggered to protect the system from unstable power.......(see below for photo of screen).
So I bought a UPS in the hopes of controlling the flow of power to my computer. Unfortunately that didn't work so I assumed that the power supply unit must be broken. I have replaced it and I am still getting the crash/error. So I simply disabled the feature on teh motherboard that controls anti-surge protection and now my computer simply crashes and powers down.
I have checked the event logs and noticed this being logged right before the crash every time:
"File System Filter 'aswSnx' (6.0, 2012-03-07T01:04:05.000000000Z) has successfully loaded and registered with Filter Manager."
dxdiag: ------------------ System Information ------------------ Time of this report: 5/23/2012, 20:17:39 Machine name: ENDUSER-PC
My desktop does not detect and external hard drive that do not come with their own power supply. I have many externals that also plug into the wall and they are working fine; but whenever it is an external without a plug, i.e. the portable ones they are never found.
They do not show up in Computer Management, so it is not because I did not assign a letter to the drive.
I have tried various things, but I don't know what I should be testing for or looking for. These externals all work on other laptops and other desktops perfectly fine so it is not the externals. When they are plugged into my desktop, they light up normally like they should, but the desktop never detects them. I have tried these externals with the different USB cable I have on hand, but nothing seems to work. It doesn't matter which USB port I plug the device in, it still gives me no response.
putting together an mobo handling 8GB ddr3 1333 & using max ram 8GB, duo core 2 E8400 3.0GHz 64bit chip, and installing Windows 7 HPrem 64bit. was wondering about how large of a power supply unit i should be considering?Sometimes all of the ram will prob be used w/ vid editing and other times just regular 2-3 applications open.
i used to get the BSOD very often so i decided to recover the system to the initial state . i did that and everything was fine , then i updated the windows 7 service pack 1 and finished the installation and rebooted my computer , the start-up at least took half an hour at that time and the service pack 1 installation showed "not successful " i tried to again to update the service pack1 which showed 73.6mb - 892.6mb so i updated it again and again the same thing happened.
I keep getting BSODs .I tried many things but doesnt solved my problem.I dont know how to open the minidump files.All i can do is use WhoCrased or BlueScreeView.But i heared they are not showing all and i must take a look in minidumps.How do i open the .dmp files?
Crash Dump Analysis -------------------------------------------------------------------------------- Crash dump directory: C:WindowsMinidump Crash dumps are enabled on your computer. On Sun 26.08.2012 07:29:29 GMT your computer crashed crash dump file: C:WindowsMinidump�82612-18828-01.dmp
I installed a power supply and removed the floppy disk from a Dell Optiplex GX520. Now when I turn it on, it says there is no serial ATA SATA-2 nor parallel ATA, Path=0 (Pri Master.) Everything is working so I don't know what the problem is.
