have an asus a7n8x-x mb with amd athlon 2500 cpu. was running with 3x512 mem tried to upgrade to 3x 1gig. running vista home basic it will not boot with anything over 2 gig total. anyone with any ideas (other than a new system)?
View 7 RepliesI am runing windows vista 32 and it is actualy running ok for me thought I just tryed to run a memory test and found that it runs up to about half or what i have then it starts over. It will do this till i get tired of watching and jump back in to my bios and tell it to run the fast test witch dose not run any real test. Then the comp will boot fine and run ok. I would really like to know how to get it to run a real mem test so i can check my systems memory. I had a problem a wile back where my main board desided to over clock my memory on its own and thought it is now runing ok i want to make sure it did not damaged the memory. I already found that it had damaged my FX card and had to replace it.
View 8 Replies View RelatedI have a system runnung Vista, XP and Ubuntu. Now I replaced the memory from 2 Gb before to 4 GB DDR2 now. After this Vista is not starting successfully anymore. During boot process it restarts the computer. Booting in safemode the last loaded driver shown is crcdisk.sys before the system restarts. Windows XP and Ubuntu are running without any problem, HDD check shows no error, even Windows Memory Diagnostics is runnung without reporting any problem. If I change the RAM back to my old 2 GB also Vista is starting again. But with 4 GB it will not.
View 8 Replies View Relatedi installed vista 64 ultimate with 3 gig of ram but i was told that vista 64 could run with 4 so when i installed the 4th gig or ram my pc would turn on but not boot (did not see any display) so a friend told me that it is a known issue and to fix it i needed to reinstall service pack 1 with just 2 gig then that would allow me to install the full 4....i did this and now my comp will not boot unless i have just 2 gig, it wont even boot with 3 gig like before,
View 9 Replies View RelatedAm running Vista 64 Business on XFX 680i Sli LT with 2Gb ram, Quad core 6600, 600GT video. System runs fine, but I want more memory to help performance. When I try to install additional 2Gb, I get a blue-screen every time I boot (some blue screens have an IRQL_NOT_LESS_THAN_OR_EQUAL, most have no error msg). Is there a way to determine if my installation of Vista already has this installed? I've already checked the Control Panel/Windows Update/Review Update History, it's not in there, I thought it may be in the core install on the DVD?
View 9 Replies View RelatedMemory DiagnosticsIf Vista detects a memory problem in your system such as a faulty RAM module, it will display a notification asking if you want Vista to try to diagnose the problem.Then again you may also recieve the sudden BSOD with the error MEMORY MANAGMENT at the top. You can manually run this tool anytime just typememory in the search box inside the start menu.This tool offers you two options: restarting immediately and checking for problems, or running next time you reboot your machine (the memory diagnostic tool must run at boot time).
Network DiagnosticsWindows Vista also allows you to check the connectivity of your network connection using the Network Diagnostics Framework: An infrastructure and a set of built-in and extensible components that attempts to automatically diagnose and correct network connectivity problems. The usual way to run this check is to open Network Center and click the Diagnose Internet Connection link on the left Vista will either identify ............
I had 4GB physical memoryon the PC. With Windows vista 32 bit, available memory is shown as 3.3GB. I asked and was told that only under 64 bit windows, will the available memory be 4GB. When I upgraded to windows 7, I chosed 64 bit, but the available memory shown in the system is still 3.3 GB. Why is this and is there a way to make the full 4GB available? It's possible that my video card is using RAM instead of its own RAM. If I install a video card with its own RAM, will the full 4GB be available?
View 9 Replies View RelatedI have a problem with Vista Ultimate x64 SP1, I always seem to lose all my free RAM within an hour regardless of system activity, even while idling. I have noticed an svchost.eve process runs each time I reboot which seems to bloat constantly although when I close it down it only frees up about 800MB, what's happening to the rest of my 8GB??? When I launch Task Manager it says I'm only using 10% Memory but free RAM sits at 0?!?!
View 9 Replies View RelatedI had 4GB physical memoryon the PC. With Windows vista 32 bit, available memory is shown as 3.3GB. I asked on usenet and was told that only under 64 bit windows, will the available memory be 4GB. When I upgraded to windows 7, I chosed 64 bit (I did clean install of course), but the available memory shown in the system is still 3.3 GB. This is show in both task manager under performance->Physical memory->total, and 'property of My Computer'->Installed memory (4GB/3.3 GB usable)........
View 7 Replies View RelatedI am fairly new to the forums, and VERY new to Vista x64. The machine is new, and I was trying out some apps and games, I was in Secondlife when I got an error messege saying I was out of memory and needed to free up memory. I shut down the app and restarted it. Runs but I watched Task manager and saw my free memory down to almost nothing after an hour or so. The cached seems very high.
I did alittle research and decided to set a second page file on my 1TB hard drive, (OS is on the other HHD's )( regulated by system for size ) I'm not really sure whats going on. Example of just task manager and this page openis attached. Again, any help would be great in getting the memory set up on here optimal.
I have 6gigs of DDR3 memory at 1600hz. Running on Vista 64bit and every now and again my memory performance just maxes out. The problem can occur around the time when I am installing something but I dont think its always this way. I have read forums where it could be the hardrives performing self diagnostics. I have all the latest patches for vista.
View 7 Replies View RelatedI went to turn it on this morning, I just had a black screen showing the following words;
Press F2 to run
Press F11 to boot menu
Auto detecting PRI Master Atapai CDROM.
It then went to reboot and select proper boot device or insert boot media in selected boot device and press a key. I went into the BIOS to change the boot order and inserted my Vista home premium 32bit. I then got windows is loading in files. After a short while I got the black start up screen with Microsoft Corporation but after a few seconds it just froze. Moments later it went to a blue screen with white writing part of which said the following; A PROBLEM HAS BEEN DETECTED AND WINDOWS HAS BEEN SHUT DOWN TO PREVENT DAMAGE TI YOUR COMPUTER.
I'm running Vista 64 Home (SP1) Premium on a homebuilt machine w/8GB (4 X 2GB modules). Windows is reporting 8 GB of Installed Physical Memory but is reporting only 4 GB of Total Physical Memory. I first noticed this when, after installing a game, the game system specs said 3092 MB of RAM.
I have checked the BIOS and it recognizes 8 GB. Memory Remapping is Enabled. Under Memory Remapping is "PCI MMIO Allocation: 4GB to 3328 MB" (?). MSConfig Boot Options shows Max Memory is not checked and no value in the box below. I tried enabling it and using 8192 as the value, but it made no difference. DxDiag shows 8 GB installed RAM. how I can get windows to make available all 8 GB of RAM? (Motherboard is ASUS Maximus II Extreme w/Intel Q9550 processor running at Q9650 clock speed, memory running at 1127 MHz
i can no longer boot up my computer as the boot/bcd file is miising or corrupt i found a windows artical on how to fix it and it didnt work ive also tryedd googleing the problem and got many results but none that seem to fit the problem or are helpful what can i do to solve this
View 9 Replies View RelatedI have a Dell Inspiron 530 Desktop and every now and then it won't boot up. I get a black screen with 'Windows Boot Manager' ," Windows failed to start. A recent hardware or software change might be the cause."
File: BootBCD
Status: 0xc000000f
Info: An error occurred while attemping to read the boot config data.
When I boot the PC with the Installation disc, it repairs it and it works until the next time. When I click on the details to see what is to be repaired, this come up:.......
I have windows xp installed right now and I dual booted with vista by re-partitioning my hard drive. After encountering problems with vista I delted the vista partition and resized the xp partition back to it's original size. I am now stuck with the windows vista boot loader which persistantly telling me that the windows vista files are not present etc. etc. Is there any way that I can delted the vista bootloader and go back to using the xp bootloader?
View 8 Replies View RelatedVista used to boot up very quickly. Now it spends ages on the page with the "loading" bar. Is it performing some sort of CHKDSK during this time? I only have sidebar and rocket dock starting up, and it's fast again when it gets to the desktop, it's just that loading bit takes quite an ages, and it didn't used to. Virus/spyware/malware free. How do i find out if it's doing some sort of chkdsk at boot?
View 9 Replies View RelatedI built a new machine.Running Vista Home premium,8GB of Ram,Phenom11 3.2MHz.
I have 2 hard drives.First one portioned to C: and D:
Second HD portioned into D: and E: I have Vista on C drive.I would like to Dual Boot Vista with Windows7.
My question is do I need a Boot loader application or does vista have the ability to dual boot?
I have more or less completed all the driver upgrades and windows updates but I keep getting repeated boot failures of Vista. I can always get into Safe mode but in Normal mode the boot fails just after the first spash screen at the point when the screen goes blank to be replaced by the small circular Vista logo. After 2 or 3 attempts it succeeds to load but then the problem seems to reoccur, particularly when I have been back to XP for a while.
I had a similar problem with XP but that seems to have sorted itself out. I have tired looking in the logs for faults and failures but no clues there. I am running an ASUS P5E MB with Intel Quad 6600, 4Gig RAM, GeForce 8800GT and 2x250Gig HDs.
This is the best install I have ever done (or was)…I did a fresh install and followed a tweak which was to very enlightening, to say the least. From there I have been to a few other sites and moved on to fully customizing my desktop/login and……well…this is where I stuffed up…My BOOT screen no longer works properly, even with the original “winload.exe.mui” file replaced.
I downloaded and used “Vista Boot Logo Generator” I loved the results on my last install…It worked well. Upon deciding to do a fresh install with Tweaking in mind, I simply coppied over a Boot logo I made previously after allowing permissions and all that as well as changing the NO GUI in msconfig…ect….BUT......
i am new to this forum but i have problem with my system bootup. my system takes too long to boot and it started 3days ago. it takes about 120secs at bootscreen alone. i believe it is not my start up programs as it takes about 3 secs to start up from login page. i donot use any third party bootscreen. normally, my system boots in 30 secs but now i am facing a lot of problem which i do not understand. i have tried all the tutorials in this forum relating to bootup problems but found no luck.
View 6 Replies View RelatedXP is on 1st primary partition [active] and is old. Vista is on 2nd Primary partition and is new. Dual boot info, I believe, is all on the XP partition. Soon I will want to go to Vista only. Do I just delete the XP partition (after imaging it, of course!) and set
Vista partition to active? (Paragon Partition Manager). Will it then automatically boot into Vista (which has no boot.ini)?
I've had Vista x64 installed for about 2 full months now and I've recently begun having a lot of problems. One being: 187 seconds. What the hell? Before you ask, here are my specs. Lots of fast memory, a fast processor, 7200RPM boot drive (not listed), and ****ing awful performance. What gets me is that the delayed boot time is before I even see the "Welcome" screen.
My current boot time distribution:
1. BIOS does all its fancy stuff very quickly (about 6-7 seconds or so)
2. I get to my boot loader and it defaults to Vista after 5 seconds (dual-booting Vista/Ubuntu).
3. I then see the Vista loading screen (black screen with green loading bar) for about 4-5 seconds................
I need to do a CD/DVD Boot and I cannot find the option in the BIOS Boot Menu.
View 4 Replies View Relatedhp tool ask to do this "Then please go to “using DOS system files” column and add the link to where you stored the unzipped DOS boot up files. "so my question is , where can i get the "dos boot up files" for vista64? with the hp tool i need to locate the dos boot file address . so how do i do that? do i have to download vista64 boot files? every google links explains how to do this with xp. couldnt find any for vista. makes me feel like im the only person on the planet using vista.
View 4 Replies View RelatedI have installed Vista on my C: disk. After that I installed XP on D: disk. Now I can't boot Vista anymore.
I tried with boot.ini. I've read that there's a program called bcdedit.exe. I tried to make that one work on XP, but I failed. I don't have Vista's DVD, and I'm trying to avoid installing XP again. If there's any way around...I would be gratefull! (Is there any way I can edit bcdedit.exe in XP?)
I was running dual boot fine between XP and Vista now im running both Vista it only reads my newly installed drive on boot and i have no boot options as you do in XP/Vista installs, im a newbie to dual drives and was wondering how to set it to have boot options now!
View 5 Replies View RelatedI searched all over the internet for this simple (I think) problem, but I couldn't find any solutions. I have installed Vista on my C: disk. After that I installed XP on D: disk. Now I can't boot Vista anymore. I tried with boot.ini. I've read that there's a program called bcdedit.exe. I tried to make that one work on XP, but I failed.
View 5 Replies View RelatedI once read a post about a boot menu reappearing on every boot. Did a seach on google and found as the 10th result the post I needed (i recognised the text in the preview shown). Search on google 'site:www.microsoft.com boot menu'Found:But......that thread no longer exists. Also I cannot find that post again.With this post result? With a boot menu reappearing?
View 4 Replies View RelatedI have a HP pavilion laptop which came with 64 bit vista ultimate pre-installed. I shrinked the OS partition (160 GB), created new partition (40 GB) for 64 bit windows 7 ultimate. After installation of Windows 7, I cannot see the vista ultimate boot option when I boot my PC. When I boot into Windows 7, I still can see the vista partition. But instead of C: it is now displayed as E: I used the HP Recovery Disc to repair windows vista but I can only see a blank blue screen with the mouse pointer. How can I recover the vista?
View 9 Replies View RelatedThe other night I was in a rush and I held down the power button until it shut off. the next day I tryed turning it on and after the MB homepage came up for 3 secs on the top left hand corner of the screen it said "Disk boot failure, please insert boot disk and press enter" so i fooled around with the priority settings a little bit and nothing worked. I then inserted the windows vista CD and it would say "Loading windows files" then the loading bar came up and it would always freeze at the same point and after about a minute a blue screen came up saying a problem occured and is shutting off the computer to prevent further damage. Iv tryed everything. could my hard drive be damaged or something? Please someone help me. I cant work with much because i cant even get into windows! :-( All i can work with is the Setup menu
View 9 Replies View Related