I have 5 USB devices (2 external drives, 1 flash drive, one CF card reader, and 1 Sony walkman) that when connected score a drive letter. My problem is that the drive letters change depending on the order in which the devices are connected (the first one plugged in gets drive F, then G, etc). This causes a headache for my backup software SyncBackPro, where I have schemes set up for my two external hard drives based on drive letters. I can change the drive letters in Disk Management (Vista Ultimate) but that only sticks while that device is connected. For instance, if I unplug my primary backup drive G and connect my flash drive, the flash drive would then become G. Is there any way of permanently locking a particular device to a particular drive letter?
I have the following setup now: C: Vista, D: CD, E: CD RW,F: DVD RW, G: = Backup Vista, H: Backup 2, I: Old Stuff. This is what shows up when I look in Computer. The surprising is that I = don't have a CD, although I do have everything else. I want to remove = the erroneous D: and rename I: to D: -- and Disk Management does not = appear to help.
I recently fresh installed my Vista Premium x86 on my homebuilt, and I had all my data backed up on my flash. When I plug it in, Vista dings like normal, but it is not in Windows Explorer and Disk Management. The Drive did have some Code 10 Device Cannot Start problems, but those are worked out when I disabled it and re-installed the driver, and the drive DOES show up in 'Safely Remove Hardware' and the Device Manager. I kinda diagnosed that it doesnt have a Drive Letter assigned, due to the flash drive working in my XP x64 dual-boot.
I want to shrink the C Drive (Vista Drive). Actually 111GB is free out of 236GB on the C Drive but I am only about to Shrink 6GB and even when I try to Shrink the Drive by 6GB I get an error. I want to create a new partition on my hard-disk. These are the screen shots:
I want to know that how can i increase my C drive. In the disk management it is showing 23.75 G.B. but in my computers it is showing 12.74 G.B. and apart from this i have F drive which is fully empty can i utilise it?
Vista Home Premium 64bit SP1. When I try to get into Storage -> Disk Management, it just sits there. At the bottom it says "Connecting to Virtual Disk Service".. I see NO disks listed, not even C:...
how my External Hard drive's letter (F Changed to G and moved to my Cd Drive. I was wondering how to change my CD drive's letter, so that I can have my external as the letter F again.
With the advent of terabyte hard drives, is there a work around for the limitatation of 26 letters for drive designations. I have a new computer with 2 terabyte hard drives, two DVD's, several USB connections, and I am running three different programs from ISO files stored on the hard drive with Daemon Tools, all of which take up drive letters. I have Windows Vista Home Premium, but see no work around for this limitation. I have searched Microsoft KB finding nothing addressing this issue. I am hoping that some one knows of a work around for the problem
I was under the impression that it was possible to partition a hard disk via Disk Management. I want to split the existing C drive into two drives but when I right click the drive in Disk Management there is no option to do this. Is this not possible in Vista?
I want to install Windows 7.I have 2 Hard Drives, both are portioned in 2 .
If I install windows 7 by booting into Vista, inserting the Windows 7 DVD and run setup.
This way I can assign drive letters that I will want to use consistently in both Operating Systems
I am a little bit confused after reading about installing Win 7. If I boot from Win 7 DVD it will assign the letter C: to its Boot Volume, no matter what drive I choose.
Then it says to assign D: to the start volume. The other letters will be in sequence.
Does that mean I need to put Win & Boot Volume on the same drive as Vista's Boot Volume?
As of now I have First Drive Portioned in to C: and D:
Second Drive Portioned into E: and F:.
I want to install Win 7 on the second drive in part ion 1 which is E:
When I install from Vista I just have to check E: Drive and the Boot Volume will be on E: too. Hopefully I will have the choice to boot into Vista or Win 7?
I would also like to give the Drives Names: Drive 1 Portion 1 Big Vista - Which is C: Drive 1 Partition 2 Little Vista - Which is D:
Drive 2 Partition 1 Big Win 7 - Which is E: Drive 2 Partition 2 Little Win 7 -Which is F:
This way I will know exactly which is which, even if Vista calls Big Vista C and Little Vista D: Also if Win 7 calls it Big Win 7 H:
I am havein Vista Home Premium instaled on mu laptop. there are three partition on my Hard disk C: 31 GB D: 5 Gb (Recovery disk) E : 75 GB I wan to format my system and want to merge C: drive and E: drive as single drive. I have recovery disk with me.I dont bother if data is lost on either drive. I just want to reinsitall every thing and create single drive.
after shrinking the D: partition, the drive letters and actual partition sequence on the drive changed - the C: (Vista) partition has switched places with the D: (Recovery) partition in Disk Management (D: is now in front of C I first defragged the D: drive using JKDefrag and used its built in feature to move all the files to the end of that partition, so that after splitting D:, the blank portion would be next to the C: partition (so I could have it merge with C: ) how do I get the partitions back to their normal positions (in Disk Mgmt)? and if I delete the D: partition, will it merges with C: and keep my Vista install harmed?
I haven't found a solution to this yet: I have 2 network driver established. They reconnect during reboots and are accessible fine. For some reason they stopped being visible in explorer until I explicitly go to them by enteing the letter in the address bar. Then one or both with show up (usually just the one I put in) I also have an internet webdav drive that also does not show up until i put it's letter in the address bar. If I use applications to access the letters, they show up ok in that application's file open/save box.
When I go into my computer I cannot see my drive letters, if I type in the drive letter I can then get to that drive:mad: this is very frustrating, I hate having to type in the letter of the drive that I wish to use
My new computer has a SATA HDD and im trying to put in an old IDE HDD but when I hook it up I get get a blank screen after the BIOS loads for about 5minutes and then windows finally loads. When I do get into Windows (Vista x64) it doesn't see the drive until i go into Disk Management and rescan disk 2-3 times, then it doesn't see its partitions until i scan again, and then it freezes my whole computer and i have to hit the reset button on my case.
The IDE cable is also hooked up to a DVD drive, I don't know if thats a problem or not. Also are their IDE to SATA adapters?
Due to an Office Enterprise issue that can only be resolved with a clean re-install of Vista on an ACER computer rather than re-installing the ACER factory load I have bought a Full version of VISTA Home Preimum so that I can do a CLEAN install. I have 3 partitions on my HD C, D & hidden, the hidden contains the factory load. My plan is to run a full back up to D as well as copies of my files. I will also make copies of my files off computer. I do have the ACER recovery disks but I hope to never have to use them.
When I am all backed up I would like to format C, get rid of the hidden partition, keep D, put the VISTA DVD into the drive and do a clean install of VISTA on C . I could be wrong but I think that it would be best to format before putting the VISTA disk into the drive so there is no confusion between product keys etc. this is not an upgrade it is the same version that ACER supplied.
I recently installed Vista with on this machine with this new HD deatched though it had previously been used in this computer running xp. It is a IDE hard drive and although device manager recognizes it as a disk drive I cannot get windows explorer or disk management to notice it. It has a ntfs format.
when I go into Disk Management, my interal hard drive, external USB harddrive (Western Digital) and Disk Drive are all unreadable. I am certain it was fine when I first installed Vista as I formatted and partitioned both the internal and external HD. I have tried rescanning and resetting my computer, both to no avail. It is interesting to note that Memory Diagnostic Tool doesn't seem to want to work either...Microsoft only suggested rescanning and resetting, so I'm at a bit of a loss as to what to do.
I have a newly installed Vista64 Ultimate system. After clicking Disk Management in the Computer Management window the service never starts. Instead, the following launching information is displayed: Loading disk configuration information…..Any idea what might cause this strange behavior.
By a process too tedious to recount I've wound up with the following primary partitions on disk 0 of my laptop, a Compaq Presario R3275US with a 75-gig hard drive:
C: System (43 gig) D: Local Drive (15 gig) G: New Volume (15 gig)
Is it possible to combine the empty G with the non-empty D without erasing the latter in the process? If so, how can that be done?
Is there a definitive description of the Vista Power Management options? Something like a system adminstrator description of all the options and what affect each change will have.
i want to put linux on my computer as a stepping stone leading towards my career and want to dual boot vista with linux unfortuneately i got 3 partitions in total. 1 that has EISA Configuration and an unknown 4.73GB (Healthy) partition, that i am unsure of what purpose it has because it has no info on it. I want to get rid of it so i have more space forlinux
I just installed a new Hitachi HDD and restored my disc image to it. My original disk had three partitions, the pqservice partition, the active OS partition (C drive) and a data partition (D drive). But I only chose to restore the OS and the data partitions. Now when I view the new disk via disk management, the labeling of the active partition is unusual; there is no volume name listed nor file system, and the free space is shown as 100%. Also, the status shows an EISA configuration. However, under explorer properties for the drive, things look a bit different, with the label and system type correct. What is causing the discrepancy and how to remedy it?I just now also noticed that I no longer have 4gb of ram... I haven't removed anything, but only 2gb are showing in system properties and in the BIOS???
I have a laptop with a 90GB hard disk. There is 60GB free and I'm trying to use the Shrink volume option in Disk Management to make the main partition smaller. After I want to create an additional partition so I can dual boot. The problem lies with Shrink Volume. Even though I have 60GB free it's only offering me the chance to shrink by 14GB.I've turned off system restore and hibernate. I've also used a number of defrag tools including Auslogic and SysInternals.
Friend has a flash drive that was working OK, but when he plugged it in yesterday, it didn't show in Explorer. When he plugs it in it makes the appropriate sounds, but it doesn't appear in Explorer or Disk management. We uninstalled all of the pertinent entries in Device Manager and tried it again, and it all reinstalled perfectly, gave notice that it was in stalled, etc., but in addition to not showing up, there is no "Safely Remove Hardware" icon, no mention of the device when I force the "safely remove" dialogue.
Tried it on another machine with the same results, tried another stick on my friend's machine and it works fine. Is this thing toast? Is there no utility that can reach into the "drive's" guts and make it come back out of hiding, or is it irrecoverable corruption?
A bit of background first. I have recently had installed a new 320GB Hard-drive to my Laptop [see my Specs]. The allocation of partition [volume] space has been divided evenly between the C:[Acer] - 139GB, and the D:[Data] - 138GB, Drives on the HD.
This is what I have;
Questions;
Question 1; Is this setup division just the 'norm' for allocating volume space for each drive? In this case it is more or less a 50:50 share of the available space [PQ Service on a hidden partition takes up the rest]....why not 65%[C]:35%[D]? Question 2; Is it necessary for the partition volume of the Data drive to more or less mirror that of the Acer drive? Question 3; If answer to Q2 is 'not necessarily so', am I then able to partition the Data drive to create a new drive partition of about 60GB, or are there any pitfalls in playing around with this particular drive? If possible, I'd like to create a new drive on the HD for personal data storage.
I have my old XP load on my C drive and Vista on the D drive. I'm ready to wipe out XP (I know lots of folks would go the other way) so I can create a mirror copy of Vista for fault tolerance. Before I enable RAID in the firmware, I'm thinking I need to format the C drive. However the Disk Management utility has the format command grayed out for the C drive. It shows up as:
Disk 0: C: NTFS, Healthy (System, Active, Primary Partition)
My D drive is: Disk 2: D: NTFS, Healthy (Boot, Page File, Crash Dump, Primary Partition)
What is the proper way to wipe out C so I can create my RAID mirror?
I'm on a Toshiba Satellite that's worked fairly well except for a few self-repaired hiccups. However, about a week ago my power management plans suddenly stopped working. I can switch from different plans that change how quickly my display turns off, but my screen has been stuck at the lowest brightness possible for a while now. It has nothing to do with the plans themselves, I've restored all to their default settings and still no change in brightness when I switch between all of them. The little slider to adjust brightness simply does not appear anymore. I can't find what exactly it is that's malfunctioning to reinstall, as no power management driver appeared on my disk from Toshiba. Can anyone provide an explanation or perhaps a link to repair this?
I downloaded Windows 7 RC1 with the intent of adding a partition to my HDD and dual booting. My understanding is that I would need a 16GB partition. My Disk Management Console tells me I have two existing primary partitions (expected). D (the recovery partition) is 6.62GB. The other (C) makes up the difference (~142GB) and has 47.1GB free space. When I begin the "shrink volume" process, it says that only 3MB is available to shrink C. I checked the page file and it has less than 3GB allocated to it. So, I have two questions. First, why isn't more shrinkage ;>) space available? Two, assuming that with your help I can find more space, if I try to create a 16GB partition from C will I significantly affect computer performance?
Recently replaced an ACER factory load with a clean install of VISTA Home Preimum. My HD has 3 partitions C (228gb), D (227gb), and hidden (9gb). Would like to get rid of the hidden (ACER factory load ). My HD is 500 GB and my total use is 51 GB on C. Would it make sense to create 3 partitions C (small) for Vista and applications, D (small) for data and E (whats left) for whatever.
Is it possible / pratical to move the entire User folder to D or would this actually cause more future trouble than it is worth. Can any of this be done with Disk Management (when I right click on the hidden I get no options) or is a third party solution required ? Or should I just leave well enough alone
