I was under the impression that it was possible to partition a hard disk via Disk Management. I want to split the existing C drive into two drives but when I right click the drive in Disk Management there is no option to do this. Is this not possible in Vista?
View 7 RepliesVista Home Premium 64bit SP1. When I try to get into Storage -> Disk Management, it just sits there. At the bottom it says "Connecting to Virtual Disk Service".. I see NO disks listed, not even C:...
View 5 Replies View RelatedIn which directory of the DVD of Vista SP1 64 bit I have to put the Autounattend.xml file in order to allow Vista to automatically erase and create the partitions of an disk?
View 9 Replies View RelatedHow do you exactly partition a hard drive or can some one tell me a good place to get a partitioning program or website for a free partitioning program downlaod and what is a good program cause i want to get a good program and not a peice of crud.
View 6 Replies View RelatedI am havein Vista Home Premium instaled on mu laptop. there are three partition on my Hard disk
C: 31 GB
D: 5 Gb (Recovery disk)
E : 75 GB
I wan to format my system and want to merge C: drive and E: drive as single drive. I have recovery disk with me.I dont bother if data is lost on either drive. I just want to reinsitall every thing and create single drive.
My new computer has a SATA HDD and im trying to put in an old IDE HDD
but when I hook it up I get get a blank screen after the BIOS loads for
about 5minutes and then windows finally loads. When I do get into
Windows (Vista x64) it doesn't see the drive until i go into Disk
Management and rescan disk 2-3 times, then it doesn't see its partitions
until i scan again, and then it freezes my whole computer and i have to
hit the reset button on my case.
The IDE cable is also hooked up to a DVD drive, I don't know if thats a
problem or not.
Also are their IDE to SATA adapters?
Due to an Office Enterprise issue that can only be resolved with a clean re-install of Vista on an ACER computer rather than re-installing the ACER factory load I have bought a Full version of VISTA Home Preimum so that I can do a CLEAN install. I have 3 partitions on my HD C, D & hidden, the hidden contains the factory load. My plan is to run a full back up to D as well as copies of my files. I will also make copies of my files off computer. I do have the ACER recovery disks but I hope to never have to use them.
When I am all backed up I would like to format C, get rid of the hidden partition, keep D, put the VISTA DVD into the drive and do a clean install of VISTA on C . I could be wrong but I think that it would be best to format before putting the VISTA disk into the drive so there is no confusion between product keys etc. this is not an upgrade it is the same version that ACER supplied.
I recently installed Vista with on this machine with this new HD deatched though it had previously been used in this computer running xp. It is a IDE hard drive and although device manager recognizes it as a disk drive I cannot get windows explorer or disk management to notice it. It has a ntfs format.
View 7 Replies View Relatedwhen I go into Disk Management, my interal hard drive, external USB harddrive (Western Digital) and Disk Drive are all unreadable. I am certain it was fine when I first installed Vista as I formatted and partitioned both the internal and external HD. I have tried rescanning and resetting my computer, both to no avail. It is interesting to note that Memory Diagnostic Tool doesn't seem to want to work either...Microsoft only suggested rescanning and resetting, so I'm at a bit of a loss as to what to do.
View 8 Replies View RelatedI have a newly installed Vista64 Ultimate system. After clicking Disk Management in the Computer Management window the service never starts. Instead, the following launching information is displayed: Loading disk configuration information…..Any idea what might cause this strange behavior.
By a process too tedious to recount I've wound up with the following primary partitions on disk 0 of my laptop, a Compaq Presario R3275US with a 75-gig hard drive:
C: System (43 gig)
D: Local Drive (15 gig)
G: New Volume (15 gig)
Is it possible to combine the empty G with the non-empty D without erasing the latter in the process? If so, how can that be done?
i want to put linux on my computer as a stepping stone leading towards my career and want to dual boot vista with linux unfortuneately i got 3 partitions in total. 1 that has EISA Configuration and an unknown 4.73GB (Healthy) partition, that i am unsure of what purpose it has because it has no info on it. I want to get rid of it so i have more space forlinux
View 4 Replies View RelatedI want to know that how can i increase my C drive. In the disk management it is showing 23.75 G.B. but in my computers it is showing 12.74 G.B. and apart from this i have F drive which is fully empty can i utilise it?
View 9 Replies View RelatedI just installed a new Hitachi HDD and restored my disc image to it. My original disk had three partitions, the pqservice partition, the active OS partition (C drive) and a data partition (D drive). But I only chose to restore the OS and the data partitions. Now when I view the new disk via disk management, the labeling of the active partition is unusual; there is no volume name listed nor file system, and the free space is shown as 100%. Also, the status shows an EISA configuration. However, under explorer properties for the drive, things look a bit different, with the label and system type correct. What is causing the discrepancy and how to remedy it?I just now also noticed that I no longer have 4gb of ram... I haven't removed anything, but only 2gb are showing in system properties and in the BIOS???
View 7 Replies View RelatedI have a laptop with a 90GB hard disk. There is 60GB free and I'm trying to use the Shrink volume option in Disk Management to make the main partition smaller. After I want to create an additional partition so I can dual boot. The problem lies with Shrink Volume. Even though I have 60GB free it's only offering me the chance to shrink by 14GB.I've turned off system restore and hibernate. I've also used a number of defrag tools including Auslogic and SysInternals.
View 7 Replies View RelatedFriend has a flash drive that was working OK, but when he plugged it in yesterday, it didn't show in Explorer. When he plugs it in it makes the appropriate sounds, but it doesn't appear in Explorer or Disk management. We uninstalled all of the pertinent entries in Device Manager and tried it again, and it all reinstalled perfectly, gave notice that it was in stalled, etc., but in addition to not showing up, there is no "Safely Remove Hardware" icon, no mention of the device when I force the "safely remove" dialogue.
Tried it on another machine with the same results, tried another stick on my friend's machine and it works fine. Is this thing toast? Is there no utility that can reach into the "drive's" guts and make it come back out of hiding, or is it irrecoverable corruption?
I refer specifically to this Tutorial;
Disk Management - Shrink Partition
A bit of background first. I have recently had installed a new 320GB Hard-drive to my Laptop [see my Specs]. The allocation of partition [volume] space has been divided evenly between the C:[Acer] - 139GB, and the D:[Data] - 138GB, Drives on the HD.
This is what I have;
Questions;
Question 1; Is this setup division just the 'norm' for allocating volume space for each drive? In this case it is more or less a 50:50 share of the available space [PQ Service on a hidden partition takes up the rest]....why not 65%[C]:35%[D]? Question 2; Is it necessary for the partition volume of the Data drive to more or less mirror that of the Acer drive? Question 3; If answer to Q2 is 'not necessarily so', am I then able to partition the Data drive to create a new drive partition of about 60GB, or are there any pitfalls in playing around with this particular drive? If possible, I'd like to create a new drive on the HD for personal data storage.
In Windows Vista it is now possible to resize partitions without any data loss in the new Disk Management console.
Resizing Partitions with Windows Vista:
Click on the Start Button and right click on Computer and select Manage.
Expand the Storage section and select Disk Management.
Then just right click on any partition and select either Expand or Shrink to change the size of the partition....
I have the following setup now: C: Vista, D: CD, E: CD RW,F: DVD RW, G: = Backup Vista, H: Backup 2, I: Old Stuff. This is what shows up when I look in Computer. The surprising is that I = don't have a CD, although I do have everything else. I want to remove = the erroneous D: and rename I: to D: -- and Disk Management does not = appear to help.
View 9 Replies View RelatedI have my old XP load on my C drive and Vista on the D drive. I'm ready to wipe out XP (I know lots of folks would go the other way) so I can create a mirror copy of Vista for fault tolerance. Before I enable RAID in the firmware, I'm thinking I need to format the C drive. However the Disk Management utility has the format command grayed out for the C drive. It shows up as:
Disk 0: C: NTFS, Healthy (System, Active, Primary Partition)
My D drive is: Disk 2: D: NTFS, Healthy (Boot, Page File, Crash Dump, Primary
Partition)
What is the proper way to wipe out C so I can create my RAID mirror?
I have 5 USB devices (2 external drives, 1 flash drive, one CF card reader, and 1 Sony walkman) that when connected score a drive letter. My problem is that the drive letters change depending on the order in which the devices are connected (the first one plugged in gets drive F, then G, etc). This causes a headache for my backup software SyncBackPro, where I have schemes set up for my two external hard drives based on drive letters. I can change the drive letters in Disk Management (Vista Ultimate) but that only sticks while that device is connected. For instance, if I unplug my primary backup drive G and connect my flash drive, the flash drive would then become G. Is there any way of permanently locking a particular device to a particular drive letter?
View 6 Replies View RelatedI downloaded Windows 7 RC1 with the intent of adding a partition to my HDD and dual booting. My understanding is that I would need a 16GB partition. My Disk Management Console tells me I have two existing primary partitions (expected). D (the recovery partition) is 6.62GB. The other (C) makes up the difference (~142GB) and has 47.1GB free space. When I begin the "shrink volume" process, it says that only 3MB is available to shrink C. I checked the page file and it has less than 3GB allocated to it. So, I have two questions. First, why isn't more shrinkage ;>) space available? Two, assuming that with your help I can find more space, if I try to create a 16GB partition from C will I significantly affect computer performance?
View 9 Replies View RelatedRecently replaced an ACER factory load with a clean install of VISTA Home Preimum. My HD has 3 partitions C (228gb), D (227gb), and hidden (9gb). Would like to get rid of the hidden (ACER factory load ). My HD is 500 GB and my total use is 51 GB on C. Would it make sense to create 3 partitions C (small) for Vista and applications, D (small) for data and E (whats left) for whatever.
Is it possible / pratical to move the entire User folder to D or would this actually cause more future trouble than it is worth. Can any of this be done with Disk Management (when I right click on the hidden I get no options) or is a third party solution required ? Or should I just leave well enough alone
I recently acquired a Dell Studio XPS 435 desktop with Vista Ultimate as the OS. My plan is to upgrade to Windows 7 in the next couple of months or so. Therefore I won't need the Vista recovery partition on the hard drive. I am trying to eliminate it and add to the C: drive partition. Looking at my drive 0 in disk management I have from Right to left a C: partition 683Gb NTFS with the usual Healthy (System, Boot, Page File, Active, Crash Dump, Primary Partition). Directly to the left is the Recovery or D: drive which is 15Gb NTFS marked Healthy (Primary Partition) and finally to the left is the last partition of 71Mb marked Healthy (EISA Configuration). No idea what that is. Right clicking in the Recovery partition gives several options including: format, shrink volume, extend volume, delete volume, mark volume as active, change drive letter and paths, as well as help.
My question is how to remove the recovery partition and then extend the C: partition. My first thought is to format the recovery partition, delete the volume and then right click the C: drive partition and extend it but I really need some advice so I don't screw up the whole disk. For instance I have no idea what if anything hapens to the drive letters.I think maybe what I am calling partitions are really volumes so you can see I am over my head here.
I recently fresh installed my Vista Premium x86 on my homebuilt, and I had all my data backed up on my flash. When I plug it in, Vista dings like normal, but it is not in Windows Explorer and Disk Management. The Drive did have some Code 10 Device Cannot Start problems, but those are worked out when I disabled it and re-installed the driver, and the drive DOES show up in 'Safely Remove Hardware' and the Device Manager. I kinda diagnosed that it doesnt have a Drive Letter assigned, due to the flash drive working in my XP x64 dual-boot.
View 7 Replies View RelatedI want to shrink the C Drive (Vista Drive). Actually 111GB is free out of 236GB on the C Drive but I am only about to Shrink 6GB and even when I try to Shrink the Drive by 6GB I get an error. I want to create a new partition on my hard-disk. These are the screen shots:
View 6 Replies View Relatedi have a maxtor 80gig hd which i placed into an external enclosure. It works fine in xp, but it is dynamic in disk management and i have to activate it everytime in disk management i connect it When i connect it to my vista based laptop computer (dell m1330) it will read as usb device connected, i can find it on disk management as "dynamic" (not foreign) but i cannot activate it. The only options it gives when i right click are: convert to basic disk ( i think its that or "format drive"), options or help. It wont let me activate it? i dont want to do the first option as i will lose lots of data??
View 4 Replies View RelatedIs it normal for Disk Defragmenter to Analyze the disk AFTER it defragments? I know it does it before and then I click 'Defrag Now' and it proceeds to defrag my hard drive. But today I was watching it and noticed that all of a sudden it stopped defragmenting and the info changed to 'Analyzing disk...'.
View 9 Replies View RelatedI have four (4) hard disks C: D: E: F: all are connected with sata cable and power cable.(of course) The F: is outside from the pc and connected via external SATA and power cable (like usb NOT usb) I know,with USB external hard disk i can use the safely remove option.
Is there any option to safely remove SATA hard disk without Shut Down the pc?
1) Start-Control Panel-Device Manager-Disk Drives-Right Click on hard disk-Properties-Policies-UntikDisable the Enable write cashing on the disk??
2) Start-Control Panel-Device Manager-Disk Drives-Right Click on hard disk-Disable??
i was messing around with virtual disk programs and made 2 disk drives that are not really there. I can't seem to be able to delete them and its really getting annoying. How can i do this?
View 5 Replies View RelatedIs this normal? My disk cleanup shown me a 257GB of files to delete on my 80GB disk. I haven't local network and no external disk. I am using vista home premium with sp1, but this problem was without sp1 too. I attached link (for better understanding) to picture of cleanup.
View 8 Replies View Related