Windows XP will not boot. After the first "Dell" screen, a blinking underscore appears on a blank page. The hard drive and all hardware are fine, as confirmed by friend computer wizards. This is without doubt a software problem.
I burned SLAX (a linux derivative) to a live CD and set my BIOS to boot from CD. SLAX is fantastic, but I wonder if I can restore windows to a previous point or investigate my boot sequence using SLAX's file manager There is a high likelihood that I have a trojan.
Side question: Would you recommend trend micro antivirus over norton? is there another antivirus option you'd recommend more highly than both of these?
I've tried knoppix, ubuntu and some other ones, but is there any linux live CD's that allow you to save and edit files already on my HD? I'm talking files just like .doc's or .jpeg's
I have a dual boot system (2 hard drives) booting Suse and XP and boot up through Suse's built in boot manager which gives me the option of booting to Windows or Linux. But since I barely ever use Linux I want to delete it off the 2nd drive so I can use it for a storage drive, so I'm wondering how to replace the Windows Master Boot Record so I can just boot into my XP drive. I'm scared that once I delete/reformat the contents of the 2nd hard drive (I'll probably use Partition Magic to do this through my XP drive) that I won't be able to boot XP up anymore. So before I do anything I want to just be able to boot into XP and bypass the linux drive before I delete it to make sure everything is ok.
On boot sequence, PC hangs on Windows boot screen - with the good old progress bar churning along for eternity. It just stays there. It is possible to boot into safe mode, safe mode with networking, etc. but never boots up normally. 'Last Known Good..." does not help at all.
I have tried 'repairing' XP using the recovery console (deleting the boot.ini file, then BOOTCFG /REBUILD and then FIXBOOT) to no avail. Do not know where in the boot process it is getting hung up and not totally sure how to determine that.Using Windows XP Media Center Edition with SP2. Plenty of RAM and disk space.
Had this problem once in the past and it seemed to self correct after about 50 reboots.
Does this sound like a re-install of XP is required or are there any other options that might work?
The Windows XP Pro SP2 CD (it's legit, I bought it from Microsoft) will not boot from when I start it up. I've already went into my BIOS settings and changed the Boot Order so it will try to boot from the CD-ROM first. What happens is that I get the "Press any key to boot from CD....." message. After I press a key, I get the "Setup will now inspect your computer hardware and configuration..." message and then the screen goes blank and stays blank. The blue Windows Setup screen never comes up. I've tried the same CD on another PC (it had XP Pro SP2 on it, not Linux) and it boots up fine so it must be my computer. Also, I tried booting a Windows 95 CD and I got a "BOOT DISK FAILURE" message. I do know that my computer can boot from a CD because my Linux CDs (Ubuntu, Fedora, and Mint) boot with no problems at all.
I have a problem with my PC. A few days ago I received a URL in MSN messenger that infected me with a trojan horse when I entered the site.
Since then, AVG antivirus has popped up every time I startup my computer and has told me "threat detected - trojan horse downloader." I proceed to heal the file, yet next time I start up the same thing happens. The file name is simply "installer.exe". Immediately after this, my internet explorer opens and opens "web.links4all.biz",which I believe re-infects me. Since then, I have worked with my PC for a few days, with the intention of coming on here and sorting out the problem when I get the chance, unfortunately, the problem has escalated.
During my usual practice, AVG popped up saying "threat detected" once again. This time, the problem was "Trojan horse flooder." I told it to heal the file, it said it was healed, but told me I had to restart my computer for the process to complete.I restarted my computer, but after the first windows loading screen, the system shuts off and automatically reboots, until it reaches this point where the same thing happens.
I've tried using safe mode, and nothing has changed, it still enters the cycle of restarting continually.
I´m looking to hide the whole boot sequence, meaning that I don´t want to disable memory tests and other things in the BIOS, just hide it visually.. The same goes for the windows XP boot screen.. I want to keep it all from being displayed; only let it run in the background and just display things when the system is up and running..
I have Win XP PC Dual Core two point sixty six Giga Hz Pentium takes about fifteen Minutes to arrive at the Windows Boot Up Screen nearly 5 Minutes to go beyond Drive Detection any ideas ?
Need to re-boot with CD to get to recovery console, and when I get to the boot menu CD/CD-ROM is in the # 3 spot and I can't get it to move to the # 1 spot. when I get to the boot menu, all I'm able to do is move the curser up/down to highlight the 3 choices but not change the sequence. Now i can't change the boot sequence.
I'm trying to get back to factory install with XP on an Acer Travelmate 8100. Have all the recovery disks, but only thing is the f2 key doesn't work. I need this to make it boot from the CD and get back to how it was when I first bought it.
I can't change the boot sequence in xp pro i get to the bios but when i go to change the first boot process and presses enter nothing happens
I logged on as admin and has done this before with this machine but now nothing happens my feeling is she has some kind of virus or somthing as her machine is quite slow but the anti virus program is not respondind neither is the restore option and im sure other programs
I want to use my restore disk but if i can't change the boot sequence how can i run it?
I have two older IBM 300PL computers and I want to change the boot sequence but I cannot figure out how to get into the BIOS. So far I have not found it anywhere and I have searched and I have tried to scour the setup options by pressing F1 right from the beginning. I am trying to load in a new OS, but if I cannot get it to boot off of the A,D, and then C, then it won't work. How to change the boot sequence in one of these IBM computers?
How to access the advanced option table (don't know how that's called) ? the one some computers can access by hitting the delete key. But it doesn't work for my computer.. Or is there any way to change the boot sequence?
I have been having a boot up issue on my compaq presario sr1630nx. When I turn on the computer now it takes me to the boot screen where I press F2 and the little dash up in the corner flashes for a second or two...disapears...and then nothing...black screen. I then have to turn the computer off manually but when I turn the computer on again and it goes to the boot screen and I press F2 again and it takes me to the default start windows normally prompt.
I hit enter and then it boots up like normal and everything is fine with the world and my computer runs just fine until the next time I turn it off and have to turn it on again. Same routine at every boot. Was wondering if the brown out may have corrupted my boot.ini file somehow and if so how to fix it. My computer was on when the power spiked twice in a two minute period then was off for a couple of hours so it could be a hardware issue as well. I have Windows xp home edition
I am running Windows XP (SP2) on an eMachines T2080 desktop. All Windows security patches and other OS updates are current. McAfee virus scan is run weekly, as is SpyBot S&D and AVG/Ewido. I am running a GeForce FX 5200 graphics card with up-to-date drivers
The problem is, while using this computer, i had a hung-up process that was slowing things down. After doing CNTL-ALT-DEL to see the process list, i accidentally shut down the explorer process, thinking it was a hung-up internet explorer. Naturally, the computer shut down, but ever since, it does not seem to want to boot appropriately. From a cold power-up, it will go through the "Windows" logo screen with the blue scrolling bar for about 10 seconds, then the screen goes black and stays black for about a minute. Rather than coming to the light blue screen where the user-id's live, the system instantaneously flashes a "blue screen" (with some white characters on the screen), however, it's so fast that I can't read it, nor can I get a screen shot of it. Once that blue screen flashes, it goes back and tries to boot again, only it gives me the options of safe mode, start windows normally, start from last known good configuration, etc. I can boot up just fine in safe mode, but the blue screen phenomenon happens for all the other options. I have tried a system restore to a previous day, and that doesn't work either.
any ideas on how to proceed, short of an OS reinstall / repair. I have seen some suggestions for CMOS battery replacement,I can copy any utility files I need just fine while in safe mode, but I'd like to try and do additional troubleshooting
System Restore problem I've been having.I did a system restore on my laptop and then got error messages when attempting to restore back to the present time) but as of just now I have a new, much more pressing problem. I restarted my laptop in safe mode an hour or so ago to attempt to do a system restore while in safe mode, just to see if that might work since I always get an error when trying to do a system restore normally.
The system restore loaded up and the blue progress bar got about 1/6th of the way across and then stopped. I let it load and after 45 minutes of absolutely no progress in starting up with the system restore, I manually shut down the computer. I turned it on again after a minute and it began to boot up, showed the HP logo, went black, then the Windows XP loading screen, went black, then the HP logo again, black again, Windows XP loading screen again, etc and just looped again and again. I let it continue this for about 15 minutes but it just kept looping. I pressed the F8 key while it was doing this and selected it to start in Safe Mode, only to have the same looping sequence continue again and again. I had to manually shut down the laptop again, and after attempting to turn it on and have it boot up a few more times I've run into nothing but more of the same endless looping process.
What can I do about this? What caused it and is there any way to fix it? I'd really like a way to access or save my data, which I can't do now since the computer is doing nothing but looping the boot sequence. i have Prof SP2
When my bios boot sequence is set to boot from CD, a 'press any key to boot from disk' sign should come up during boot-up. It doesn't (it always used to when I set CD drive, not HD as first boot). I have not got the bios HD set as first boot, but have set it to boot from CD as first boot. When I boot up it goes straight to my HD / XP OS !
I need to boot from disk and I can't work out why the bios boot sequence I have set and saved is being ignored. My bios is not buggy and has never caused any problems until this issue. I have a MSI K9N Platinum mobo.
I have Windows 2000 Pro running. I have two 120 GB HDs. One is C, the other is D and E. I tried to install Partition Commander. I decided that I did not want to install it, so I exited the program. Then I went to remove software and indicated that i wanted to remove it. It accomplished all OK.
Now, when I restart from a power off, the black and white boot sequence stops and asks if I want to boot from master boot 0, 1, 2 or 3. I indicate 0, and it boots OK. How do I get rid of this problem? My computer used to boot from off to my Windows desktop, nonstop. I was trying to change partition sizes but decided to keep what I have.
My main computer's installation of windows (XP Home Edition OEM SP2) is completely dead. Due to a driver problem (to do with having alcohol 120% and daemon tools installed) it resolutely refuses to boot up, even in safe mode. I've tried everything to fix it, including several repair installatios of windows and much rummaging around with the recovery console, but it's gone, I need to reinstall.
Windows is installed on it's own partition, so I don't mind terribly having to reinstall, but one thing I'm annoyed about is having to reinstall all my programs (that are on their own partition too) when I lose the registry.
What would cause me to have to change my boot sequence everytime to get my computer to boot into windows ? When it restarts after I change the boot sequence it goes right into windows xp. I recently had a new hard drive and more memory put in the computer. It will not boot into windows xp until I go into my setup and change the boot sequence everytime. Then it will boot into windows. The computer is about 6 years old and windows xp was an upgrade to 98. Once the computer is in windows it works just fine. Changing the bood sequence everytime is a bummer.
I'm having trouble when I enter my BIOS. It seems that once I enter, I can't move up or down or do anything at all. At first, I thought it migt be my keyboard, but I switched my keyboard with the keyboard from my other computer. It still had the same problem. I don't know why my BIOS won't let me do anything. Can anyone please help? I just want to change the boot sequence so I can wipe my drive
I was running a dual boot of windows XP and Ubuntu Linux prior to installing Vista beta 2. Now, after upgrading windows XP to vista beta 2 i no longer have the boot screen that allows me to chose between my linux boot and my vista. Any way i can get back into linux? I did not make a boot disc for linux.
First I'll describe what I intended to do, followed by me explaining my problems, and ended with my actual question.Intentions:Fixing my Master boot record file with a FIXMBR and removing my Ubuntu installation due to lack of usage, amongst things. Merging the old Linux partitions space with one of my current NTFS partitions for the extra space (all above-mentioned partitions are on the same HDD, for the record). Would've done this with Partition Magic.
I'm trying to dual boot 2 different installs of xp pro from 2 drives using the Windows boot loader. I've edited the boot.ini every possible way I can think of, but nothing works. I've done this plenty of times using a linux boot loader or dual booting from a single drive but I cant figure this out. I haven't been able to find any reference to this subject anywhere, but I think it would work. Anybody have a clue as to how to do this? I know I can use a different boot manager to accomplish this, I just wanted to make the Win boot.ini work. Or, does anybody know of a good boot manager if I cant make this work?
I really hope someone can help me with this one. I don't know what's going on. I never had any problems installing MSN Live before and now, it's a real pain. I just got my PC back from the tech guy. He formated my computer and reinstalled Windows XP including the Updates, I'm trying to install Windows Live Messenger (MSN) and it's not working. It's giving me errors like, to check that I have enough hard disk space (I have 176 GB free space), If my computer has a firewall , and that I make sure that my computer meets the system requirements I do meet the requirements
A few days ago I installed ubuntu on my hard drive, now I'm trying to reinstall xp, and I'm having some troubles. My hard drive is partioned, into two sections. One, a small one for the xp installation, and a bigger one for all my data. The smaller one I've installed xp on numerous times, never had an issue till now. With this same xp disk. But now, whenever I try, after the initial screen, (The one that lets you format, then it copies the files over to the drive, and then restarts your pc.) it either JUST Lets tells me to press any key to boot from the cd, as it did before, or, with no cd in, leaves me on a blank screen, with one underline in the upper left hand corner. I can wait for as long as I want in either case, but the xp installation never starts up. Is there ANYTHING I can do to get it to work? It never happened till I tried linux. People are telling me to just reformat the whole drive, but that has so much stuff to back up on it, and I don't have another hard drive to do it on..And like I said, it never did this till now. One other thing.
Before linux, the partion that always had windows on it was "c" and the data part was "d". now the windows setup lists the data part as c, and I never switched it, nor do I even know how..I also don't know if that matters, But I figured I should say it, just in case. If anyone can give me any help, that'd be awesome.
I have seen stores displaying XP software upgrades for previous versions of Windows. What options would I have if I wanted to place XP on my home built LINUX system?
I am thinking of running windows xp and linux on the same hard drive. I know I load windows first, but is there a boot loader that will allow me to choose which os I want to load up at start up?
i am thinking of getting rid of windows xp and using linux instead (DSL version 4.2).will i be able to install windows programs? will it have the featurss like a word processor and paint?will i have to install my own scanner and camera wizard or will it cum with linux? whats the difference between linux and windows xp? i know that the DSL version 4.2 of linux is only 50MB. and hardly takes any space of your hard drive, especially ram. will i be able to change the theme of linux into an xp classic theme or any other theme?
