Setup Installation :: SSD Not Registered On Boot After HDD To SSD Cloning
Feb 17, 2014
I recently purchased an SSD to upgrade my Dell Inspiron 17R SE 7720 that runs Windows 8. This is the SSD I purchased and it came with cloning software: Amazon.com: Samsung Electronics 840 EVO-Series 250GB 2.5-Inch SATA III Single Unit Version Internal Solid State Drive MZ-7TE250BW: Computers & Accessories
I placed it in an external enclosure and cloned my HDD to the SSD using the program. After the cloning procedure the disk management looks like the figure below.
To me this looks good. But when I replace the internal HDD with the SSD it does not boot from the SSD at all. It takes me to the boot options and I don't see the SSD listed anywhere. I may just not be used to the Windows 8 setup.
View 9 Replies
ADVERTISEMENT
Jan 15, 2014
i have a Lenovo Ideapad Z585 running Windows 8, secure boot, gpt paritioning and UEFI bios.The laptop comes with a factory shipped 1TB Sata drive which i want to replace with a Kingston V300 SDD 120GB drive.
I have followed this guide How to Migrate OS to new Hard disk.Ive run this in another desktop, it completes and i shut down, remove the destination and insert it into the laptop - power up and it blue screens with There has been an unexpected error message. Trying to access the recovery partition says it is damaged but looks like its almost going to load. Looking at the drive in EaseUS paritition master the paritions look a perfect copy apart from the proportional sizing.
AHCI is enabled in bios - i've tried EaseUS Backup clone, task was successfull but again blue screens but this time with a attached device cant be found.
One thing i wasnt sure about, the PC i done the cloning in has a RAID stripe setup but not sure if this effects it.Any one had success in cloning a GPT drive over to a SSD?
I cant do a fresh installation of windows 8 as i dont have recovery discs, nor does the onekey recovery software allow me to do so and id like to keep the recovery parition in tact really.
View 7 Replies
View Related
Jan 25, 2013
I am running windows 8 pro in a Intel i5 3470 + Gigabyte B75M-D3H system with UEFI bios .
I have two drives OS drive is a SSD & a 1 tb HDD with two partitions.
I am removing the SSD & want to transfer OS to one of the partitions on the HDD , the issue is boot files on the small 350mb system reserved partition on the OS drive , not sure how to transfer this partition or if this partion in on the SSD or the HDD.
This what my drives look like , C: is SSD :
Before i installed the SSD , I was running win 7 from the HDD installed in the 170 gb partition , to install the SSD i had to remove the HDD then do a fresh install of win 8 on the SSD & connected the HDD back later ,
The 170gb HDD partition is still untouched & has the old OS files , I want to transfer the SSD partition back to this 170gb partition i.e drive F: in the above pic . I am not sure how to transfer it & what to do with the system reserved partition .
View 3 Replies
View Related
Jan 9, 2014
have Acronis 2013 Plus. What I am trying to do is image the disk of a Windows 7 machine (source) to a machine that had Windows 8 pre-installed (target - Gateway SX2110G).
I connected the Windows 7 drive to the new machine (USB data cable), disabled Secure Boot, and enabled Legacy. Booted to True Image and started the cloning of the drive. Everything seemed to go ok, but as soon as it starts to boot Windows 7, it gives a 7D BSOD. (the same BSOD it gives when I simply plug the source hard drive into the target and try to boot from it).
The source HDD (win 7) boots fine in its original machine.
*I tried the startup repair that's included with the image.. does it matter if I use the one from a disc instead?
View 7 Replies
View Related
Dec 30, 2013
- I just upgraded to Acronis 2014. Installation went fine. I have Windows 8 which is not letting me boot from the Acronis 2014 bootable media. Drive 1 (internal) is the source drive and Drive 2 (internal) is the target drive as per Acronis instructions. The Acronis Bootable Media is in the CD.
- It will never boot from the Bootable Acronis CD.
- Starting The Clone operation from inside windows 8 results in quickly needing to reboot and then nothing happens - nothing changes. If I reboot hard or soft it boots back into window 8.
- What specific instructions do I need to follow to get my new program to work in Windows 8?
- I do have a second computer that uses windows 7. Would the Acronis 2014 work on that computer if I wanted to have both the source and target drives in external USB devices? Other instructions I would need?
- Any other ways to clone a drive when I have windows 8?
- Any other ways to clone using the windows 7 computer as a foster parent?
I am trying to clone from a 2 TB drive to a 3 TB drive. Both are Seagate drives.
View 14 Replies
View Related
Feb 2, 2014
I've had Win 7 Pro on my laptop for over a year. I installed a 2nd hard drive to it recently and today I installed Windows 8 Pro on the 2nd hard drive. It's been a roller coaster of good & bad luck.
The first install went fine, until I tried to install the Windows 8.1 upgrade from the Windows store, then things went bad and I had to go into Windows 7 and eventually delete the Windows 8 volume and change it from MBR to GPT because of UEFI (no secure boot enabled). What a stretch of error messages telling me I can't install Windows 8 on the blank hard drive because it was or wasn't MBR or GPT, or the automagically made partitions weren't in the right order.
After spending over 7 hours twice in a row installing Windows 8, I finally find out that there's no boot option for Windows 7 anymore.
The only clue I have is to use a Windows 7 repair disk and use diskpart.exe and make the Win 7 drive "active" but that's a little foreign to me at this point.
I'm looking in Computer Management / Disk Management from within Windows 8.
Disk 0: SYSTEM D: 438 MB NTFS (lengthened from 199 MB with EaseUS because Acronis 2014 thought it too small while crashing), Healthy (Active, Primary Partition); Win 7 E: 930.98 GB NTFS Healthy (Primary Partition); HP_TOOLS F: 102 MB FAT 32 Healthy (Primary Partition)
Disk 1: 300 MB Healthy (Recovery Partition) {no letter}; 100 MB Healthy (EFI System Partition) {no letter}; C: 931.00 GB NTFS Healthy (Boot, Page File, Crash Dump, Primary Partition)
And several other external disks which don't deserve mention today.
View 1 Replies
View Related
Aug 21, 2013
First, some context: I have a Dell Inspiron 15R SE that came with Windows 8.
I've managed to get a working dual-boot system with Ubuntu 12.10. I can't remember exactly how I done that, but I remember that I had to disable secure boot. I think that the boot configuration those days was:
Secure boot: DisabledLoad legacy option rom: EnabledBoot list option: Legacy
This "configuration" worked perfectly for 6-7 months.
Then, one day (last week, can't remember the exact day), when I was using Windows 8 the computer crashed. I hard-rebooted and got this screen:
After executed boot-repair from a Ubuntu LiveCD dozens of times I've decided to eliminate Ubuntu temporarily and focus to get a system with Windows 8 working nice.
Then I used my recovery DVDs to recover the system. Yup, Windows has booted. But when I restarted first time I got the same error. Then I, digging a solution, pressed F12 after a reboot and got here:
The highlighted option allows me to boot into Windows 8. So I went to boot options (F2) and changed the following configuration:
Load legacy option rom: DisabledBoot list option: UEFI
Now I can boot directly to Windows without need to press F12.
But my objective isn't complete. I want to erase all Ubuntu entries from the seconds image and restore the legacy boot from the first imagem (because they worked before).
I did two things:
I erased all partitions related to Ubuntu (root partition and home partition).I created a Windows recovery disk (not a system recovery disk).
I used the recovery disk to run the automatic recovery procedure (I forgot the exactly name). I've runned it at least 10 times with no success. Then I went to command prompt to try the famous triad: bootrec /fixmbr, bootrec /fixboot and bootrec /rebuildbcd. Still, no solution.
View 2 Replies
View Related
Mar 24, 2014
After creating a UEFI bootable USB thumb drive with Rufus (using Windows 8.1 Enterprise ISO x64), for a Dell Optiplex 3010 (configured as UEFI only, no CSM, latest firmware version, Windows 8 installed), I didn't see a USB boot option, so I tried to add one manually. Unfortunately I erased the existing boot option (boot manager) by mistake. Although there were two boot options for PXE booting, the machine will not start anymore, even when there is an active WDS server on the network.
I also see Led's 2 and 3 lighting up, meaning according to the manual 'hardware ok but bios possibly damaged/corrupt'.
I understand I cannot start the machine from a bios boot disk because of GPT partitioning, and the UEFI USB boot disk I made might be corrupt (as it didn't show up as a boot option), however I don't understand why it won't boot from the PXE network card, as these boot options are still there.
View 4 Replies
View Related
Jun 28, 2013
I have installed Blue 8.1 on a separate drive in my system along side 8.0. When I restart the 8.0 boots unless I manually select the 8.1 drive in bios. How can I alter the Boot menu to add the option to boot from either OS?
View 3 Replies
View Related
Feb 18, 2013
Late last Fall I bought a new Desktop, an HP H81414, with Windows 8 installed with the intention of installing Windows 7 on an SSD. I migrated Window 8 to an SSD, removed that from the system, installed new SSD and put Windows 7 on it. Both worked fine. I wound up with 2 SSD's. capable of running on the EFI BIOS machine with Secure Boot turned off. I later bought a new laptop with Windows 8. I found the Win 8 with Classic Shell to be very acceptable.
What I would like to do now ,if possible, is to mount both SSD's in the HP case and switch to either one of them at boot.
View 3 Replies
View Related
Apr 28, 2014
I had windows 7 running on my computer. When windows 8 came out I used a second harddrive as the windows 8 installation drive. Windows 8 automatically setup a dual boot system where every time I started the computer it took me a windows screen where I could select either windows 7 or windows 8. This has been going on since Windows 8 was released.
I decided it was getting old so I decided it was time to remove the old windows 7 harddrive. I tried doing it inside the windows 8 dual boot screen but could not find an option. So I decided to reformat the windows 7 harddrive. I did this in command prompt mode. After doing so when my computer restarted it said it could not find any harddrive to boot. Windows 8 is installed on the other harddrive, the one that was not reformatted. So how do I get it to start using that harddrive as the boot drive? I checked my bios and even physically disconnected the old HD that had windows 7 on it, but none of that seemed to work even though the Windows 8 HD is definitely in the boot order in the bios.
View 5 Replies
View Related
Jan 6, 2013
Here: [URL] .....
Somewhere in that link it says:
During POST enter "BIOS Boot Selector Menu" by pressing F7.
Intel says: <F7> No uefi setup option in boot selection
Others say: <F8> No uefi setup option in boot selection
I say: <F12> No uefi setup option in boot selection
Lenovo Z580, my brand new laptop that is, its UEFI based and vymrdal's ISO from MSDN is also created to be installed as an UEFI Install.
View 3 Replies
View Related
Apr 4, 2014
I get as far as " a driver is needed to continue installation" not found, make sure its on the right media. Here is what i got done on my own..
1- BIOS setting "legacy" and U E F I" boot from USB.
2- F 9 to choose boot order.. selected USB device
3- Installation starts for WIN 7
4- Driver is needed to continue, and i have no clue what it is..some one pointed me to . f 6 f l p y-x 64 because its an HP Envy...
5- Driver not found / wrong driver..
6- Shut down restart.......................
My DVD is Windows 7 ultimate X 32, X 64..
No matter what i cant boot form my USB /U E Fl /WIN 7 pen drive.seems like its not recognized or drivers for the USB chip set not installed.. Of course using the O E M DVD of win 7 fails. because of the G P T style.
View 2 Replies
View Related
Apr 10, 2013
how can i fix iron error: "Class not registered", in windows 8 64 bit! I mention that the error appears when i launch iron from the shortcut taskbar (when i press mouse left click); when i press right click - new iron window, everything is working just fine! What should i do?
View 2 Replies
View Related
Dec 3, 2011
I cannot boot Windows 8 without the DVD but I'm thinking its not Windows 8 and the bootloader its my motherboard along with the IDE 2nd hard drive (BIOS settings?). I get a message about my secondary maxtor IDE drive upon boot up. It says something like choose the following 1) FD No Emulation system HD00 2) FD No Emulation system HD00 2). It doesn't stay there too long it defaults to 1) and then says press any key to boot to DVD... then it boots up to Windows 8. However, if I do not have the Windows 8 DVD in the IDE DVD drive it will not boot it just flashes the "_" underscore and hangs. If the DVD is in the drive it works.
Gparted partition tools shows the correct boot flag. I'm not sure about the Fdisk status of the partition table maybe that will be next. I'm wondering if I should try the bootrec /fixboot command but concerned about having to start from scratch again.
ASUS M5A88-V EVO AMD 880G AM3+
Kingston Memory KHX1600C9DX2K2/8GX Hyper x Gray 2X4GB (8GB)
Thermaltake TR2 600W ATX12V
AMD X4 970 black edition
No video card yet
Western Digital 160 GB sata (Not a Raid just a default setup)
Maxtor 160GB IDE
Phillips DVD 16x IDE writer.
Standard DVI monitor & cable
Antec 300 case.
View 6 Replies
View Related
Sep 12, 2013
I am trying to install a new OS and I want to boot from the CD on Windows 8?
How would I do that?
View 4 Replies
View Related
Nov 3, 2013
How to make usb bootable. I have done the following:
- Used "Rufus" as per tutorial to make UEFI Bootable USB Flash Drive
- used a software to test usb if bootable and it was.
- Set Secure Boot off
- Adjusted BIOS to boot usb (kingston) as primary.
I try restarting and nothing happens.
View 9 Replies
View Related
Oct 13, 2013
I have an external hard drive that I formatted to install Windows XP on. However, when I try to boot from the disk it just skips it and boots to Windows 8. I have tried going into the BIOS and putting the CD/DVD drive as the first boot device, and I also tried disabling secure boot, but neither of these worked.
View 2 Replies
View Related
Sep 15, 2014
I'm trying to dual boot Windows 7 Ultimate 64-bit and Windows 8 Pro. I want to have each OS installed on separate Hard drives. I want the default OS to be Windows 7 (loads automatically) or goes to the boot manager screen and choose either Win 7 and Win 8.
I've been running Windows 7 on an SSD hard drive with a UEFI Boot. I'm looking to install Windows 8 on a WD Caviar Black 1 TB drive.
Steps taken:
-Burnt Windows 8 to DVD to boot and install from.
-Re-ordered boot order to boot from DVD
-Windows 8 install starts
-Windows 8 drive screen - format the WD Caviar Black 1 TB to install Windows 8 on.
-ERROR Message appears - Can't find media location (I didn't write it down but will on next install I will update). Something like 0x00007B. The solution I found was to disconnect my Windows 7 drive (and all other hard drives).
(Issue: won't that affect the set up of the dual boot?)
-Disconnected Windows 7 drive and was able to install Windows 8.
-After successful install of Windows 8 I re-started my system expecting to see the dual boot menu options. However, Windows 8 loaded directly.
-Changed boot drive order to SSD (with Windows 7) then WD 1TB Drive (with Windows 8). However, Windows 7 then loaded directly.
-I rebooted into Windows 8 and went to the boot order menu in Settings > Control Panel > System > Startup and Restore > (might be a few other tabs). The drop down box shows Windows 8 but no Windows 7.
So, I'm sure I did something wrong on the install. Any thoughts?
If the SSD is a UEFI boot should the WD 1TB (Win 8 install drive) be the same? Is it critical to have the Windows 8 drive connected while installing Windows 8 to the other hard drive? If so, I will have to solve the error message I get after formatting the WD 1TB drive during the Win 8 install. (I know not having the specific error code doesn't work - will update tonight with that info).
Also, I have a 2TB drive that I think has a MBR partition. Would that affect things? Should I even have that? I'll confirm that too. Just hoping to possibly get the ball rolling with answers.
View 9 Replies
View Related
Sep 15, 2014
Lenovo g505 History - What I did so far, is further down Computer went badly wrong and would not Boot into Windows (belongs to my mates 11 year old) I decided to a Factory Restore it seemed the best Option as my knowledge stops, til now, at Win 7 I did it, but it doesnt Boot into Windows CURRENT I have the HDD connected to another computer which is running Win 7 I can now see that it did indeed do a Restore to the System Partition Pic Shows Disk in Disk Management
Pic shows content of Windows8 Drive
Pic shows content of the Windows8 Windows Folder
PDF of the 3 Pics - easy to read detail
In Disk Management I see 7 Partitions Now I think I understand what the Problem is - ?too many Partitions? But I dont have a clue how to Resolve it correctly My inclination is to Run DiskCheck from Win7 on the HDD but I am not sure if that will work on Windows 8? same with FixBoot if it is Possible? The LENOVO H Drive has 3 Folders with Data in it Lenovo & Drivers & Applications
HISTORY
I did the Restore
took 3 hours
but then said Success
Option to Reboot or Shutdown
Chose Reboot
eventualy Booted to a Windows Pale Blue screen with the Cursor half hour later, the Box came up to start the Restore again I did it, same as above time and Result so this time I chose Shut Down Started - Logo for long time then loading Files and back at the Box to Start Restore again
I have since tried booting with Default Options UEFI and Legacy in the BIOS In the middle of all this, as it is about 4 hours to do the restore.
View 4 Replies
View Related
Sep 19, 2013
I've made a UEFI Win8PE by WADK , then burn it to a CD. I boot normal and I can see X:WindowsSystem32.
I use EasyBCD to [Add New Entry] to append new boot item to existing Windows 8. The boot menu becomes like this :
Windows 8
Win8PE
But the Win8PE fail to boot with error message like insert Windows disc again ...... in the primary black and white screen.
Should I not to use EasyBCD to [Add New Entry] ? As I do the same thing in BIOs + MBR harddisk that booted perfect. In UEFI + GPT partition , do I better not to use EasyBCD , instead to use BCDEDIT , if so , what's the command line to do this with bcdedit ?
View 9 Replies
View Related
Jul 1, 2013
I have the blue win 8 bootloader with my os's but this is what it says when I choose Ubuntu
View 3 Replies
View Related
Jan 2, 2014
I had my system set up for Dual boot (on separate hard drives) for both Win 8.1 and Win 7. Win 8.1 developed a problem and unfortunately the only back up I had (my fault) was for Win 8 before I installed Win 7 and the dual boot.
I reinstalled from the backup and then updated Win 8 to 8.1. Both the Win 8.1 64 bit and the Win 7 64 bit work OK but the dual boot is now missing in Win 8.1.
Is there any way of repairing/creating the dual boot, either in Win 7 or Win 8, without using BCD Edit?
View 5 Replies
View Related
Feb 20, 2014
I have Windows 8 x64 preinstalled on my Toshiba Laptop. I created a startup disk (DVD) but i cannot boot from the DVD/CD Drive. I set my BIOS to boot from my DVD Drive but i think the problem may be my autoplay settings from DVD Drive. I just don't know how to set them up. the Disk is fine it is not scratched or anything. I don't know how to set up my media devices especially optical so that i can boot from the DVD Drive!
View 1 Replies
View Related
Nov 25, 2013
Laptop came with Windows 8 and has been updated to 8.1
Installed Ubuntu on a new partition, but no matter how many times I try, I can't get the machine to load Grub at power-on. If I boot Super Grub Disk/Rescatux, I see the installed Ubuntu, but other tools (like EasyBCD) only see Windows.
Apparently, we're no longer using MBR? Everything I used to know about computers seems to have become false in the last year or 2. How do I get Grub working on this new EFI thing?
View 2 Replies
View Related
Nov 26, 2013
I have a dual boot (Windows 7 & 8 on separate hard drives) system that is performing flawlessly. I'm considering doing the free 8.1 update (updating Windows 8), but concerned that it might mess up my current beautiful dual boot configuration.
View 5 Replies
View Related
Jan 11, 2013
I have windows 8 installed from dvd and after a restart the pc won't boot anymore. It tells me:
Your pc needs to be repaired. The required boot configuration data file is missing some required information.
File bootbcd
Error code 0xc0000034
So I tried to rebuilt the bcd, used the bootrec commands , tried auto repair, tried system recovery but nothing seems to work.
View 9 Replies
View Related
Jan 5, 2013
just want to check that i can duel boot win 8? in short unplug my win 7 drive and install win 8 on a separate new drive. plug back in and choose between 7 or 8.
View 3 Replies
View Related
Jun 7, 2014
I have sony vpceh3aen laptop with windows 7 home basic. I have IOS file of embedded windows 8.1 industry pro with update via dreamspark.com. just now I run windows 8.1 upgrade assistance and its says "your pc's firmware doesn't support secure boot so you won't be able to use it in windows 8.1". Some persons says that not a problem. I not like to upgrade my OS but I want create dual boot with windows 7 home basic and embedded windows 8.1 industry pro.
my questions:
1. can I possible to dual boot? if possible how to create it and what are changes(in BIOS and windows 7 settings) needs to make in my laptop?
2. I have pen drive and DVD, which is best for create dual boot with IOS file?
3. I have 100GB free logical partition. that is enough for embedded windows 8? if not how much need to increase?
View 2 Replies
View Related
Jul 13, 2014
So I have a Toshiba laptop with win 8 preinstalled in it I want to dual boot it with win XP However I managed to boot to the CD after some research but when I reach to installing win xp to my virtual partition I can't seem to find it I just see my HDD as one without a partition... what can I do?
View 8 Replies
View Related
Nov 23, 2012
I got my new PC and wanted to downgrade to Windows 7 since it was running Windows 8 and I found it unbareable. It didnt let me run the USB on any of the advanced menus so I tried just overinstalling it so I could go back to the old menu and try it like that (windows 8 never showed the company logo when booting up, it just was a black screen til pop! it was fully loaded) so I just ran it off my USB on my computer (bootable usb) and then it went through normal installation and expanded files and wanted a pc restart. After restart it wont show up anything on my monitor... the keyboard lights up and works for a little bit. The pc runs for like a minute or 2 and then restarts when i guess it cant find the monitor signal. I installed it on the windows C: partition but not deleted or overwrited the recovery one by default.
View 2 Replies
View Related
