Dell :: Inspiron N5010 - Error 0x400110020000100a During Restore
Nov 21, 2012
I wanted to restore my laptop back to factory settings before passing on to a friend, but when running the DataSafe restore software something went wrong and the laptop will no longer boot...doesn't seem to recognise that the hard disk is there.
BIOS settings recognise the disk and going into Boot Options (F12) I can get to diagnostics which gets as far as the memory tests then the processor overheats and the laptop shuts down (which was why I got a new laptop in the first place!)
Fortunately (I thought) I have the Recovery DVD that I created when first used the laptop, that boots fine and but when try to restore to factory settings it produces the error 0x400110020000100a as soon as the formatting screen comes up.
The laptop is an Inspiron N5010 if that makes any difference.
My Dell inspiron 17 SE on Win 8.1 has crashed when I was trying to initiate a factory restore. I did the free upgrade from 8 – 8.1 and since installing I have had nothing but problems.I was in the process of formatting the HD to return this junk heap to the store where I purchased it, when I had a message of “some files are missing, please insert media”.I pressed cancel, restarted the computer - which then into a loop, and that’s all it does now.The sequence is:Start up - Automatic repair (your pc did not start correctly) - Preparing automatic repair - Diagnosing your computer - Your PC ran in to a problem and needs to restart - repeat.I then ran trouble shooting and F12 diagnostics which told me nothing was wrong and then proceeded back into the same loop on exit.
On my friend's Dell Inspiron laptop, Windows 8 will not boot. I want to boot to the repair disk to restore an image I had created. F12 on boot does not show the DVD drive as an option. I went into Setup/Boot and disabled Secure Boot, still did not show the DVD as a boot option. I went back to Setup and selected Boot List Option>Legacy. Now it shows the DVD drive as an option to boot. I booted the repair dis, went through all the dialogs to select the image I had created, but when it goes to restore it it says it cannot because the image was made in UEFI, and it is now set for BIOS.
I went back into Setup/Boot and I see that the option Load Legacy Option ROM is now Enabled, it did it on its own. As a test I set it back to the defaults and re did it as above, and again it automatically changes Load Legacy Option ROM, which I assume is what is creating the problem.
So my question is what do I need to do to boot from the Windows Repair Disk?
I have had a Dell Inspiron 3520 for 3 weeks now. It has had 2 Windows Updates in that time. Both times I lost Internet connection and any way of connecting. The connection bar for the wi-fi was on, connection good but no Internet. After a lot of chat with Dell I did a System restore to Factory settings the first time (16 days ago). I also did a restore point once I'd re-set everything up again.
2 days ago the same thing happened after a Windows update and I also could not locate the restore point so it was back to Factory settings.
I recently had to do a system restore through the Dell System Restore programme, however now it appears I cannot activate Windows 8 - I get the "Windows cannot activate right now. Try activating Windows later".
I have tried entering manually through a command prompt but all I get is an error 0x8004F80B. How to resolve this?
I have dell inspiron 5521 with win 8 pre install The Problem is that there is a warning in "Control PanelAll Control Panel Items System" is "Your Windows Experience index needs to be refreshed" and when I try to refresh it will continue for some time and then shutdown in between with Pop Up warning "The Windows Experience index For Your System Could Not Be Computed". And when i try check for solution in action center under Maintenance,this step show me a error i.e
"Problem: Video hardware error. Files that describe the problem: WD-20140116-2008.dmp" ....
I have Latitude 10 tablet that now has Enterprise edition of Windows 8 installed and this has removed the Dell Picks section in the Microsoft app store. Is there any way to get this back? I have an app installed on another device that is Dell exclusive and I cannot find any way to get it installed on the Latitude 10 even though it is a Dell device.
The first thing I wanted to do to it was transfer the OS to an SSD, and use the 1TB drive that came with the computer as a data drive.
I wanted to shrink the C: OS partition so it would fit on my SSD but the Windows Shrink Partition tool wouldn't let me due to unmovable files.
I tried using the Windows 7 File Recovery backup tool to do a backup. With over 500 GB space on my backup drive and only 65 GB used on the 1Tb drive I was backing up, it kept telling me not enough disk space. Eventually I gave up.
I opted to install EaseUS TODO Backup and tried to backup the the whole 1TB drive. It raised an error indicating too many unnamed partitions. I opted to backup only the C: OS and the EFI System partition - leaving 3 oem hidden partitions not backed up as I wasn't going to do anything to them anyway. It worked.
I used EaseUS Partition Master to shrink the C: OS partition to 120 GB. Worked again.
I thought now would be the time to generate the Windows backup - created an image OK. Afterward however, it failed to generate the system recovery disk indicating some invalid parameter error. This was concerning. I went to the Dell Backup and Recovery tool and it told me it couldn't find the recovery partition. Not good again.
In disk management, all partitions are still there. I'm pretty sure the 3 OEM hidden partitions (40Mb, 500Mb, and 14.73Gb) had names in brackets like 'Healthy (Recovery Partition)', ... They all just say 'Healthy (OEM Partition)'. I'm guessing EaseUS Partition Master messed up their names and/or messed with their content.
At this point, the computer still works fine, and on the second pass I was able to backup the entire drive using EaseUS TODO Backup. I can't use the Dell or Windows backup utilities. I'm not sure what mess I created by messing up the 3 oem partitions, or if I can recover somehow.
I was wanting to dual boot a Dell pc inspiron 600 with win 8. I thought I will breeze through it like I used to circa WXP/Vista/W7 and didn't research what changes there might be with Windows 8. I have focused my attention more on Android and I really should have done that research.
I hadn't backed up externally docs that I needed to save - so I will remove the drive and copy the contents to my laptop to be on the safer side. So the first wrong move has led to missteps.
I downloaded Easus and created a blank disk space before the current active partition instead of behind it. I thought I needed to have win 7 in the first partition. Before rebooting I also installed a popular freeware boot selection manager (I totally forget the name but I know some most will know the one I am referring to EDIT: ***EasyBCD*** ). It gave me a warning that no bootable system was selected. I kept editing to point it to current Windows 8 but nothing changed. It also warned me that my pc might not boot. I thought I will fix it to a bootable drive with my old discs-Ultimate boot cd, CPM, etc. Easus performed creation of the new partition and then trouble started. It refused to boot.
None of my discs are working as they did before Windows 8. on UBCD Fdisk cannot find any partition it can make active. I decided not to write an new MBR. My windows 7 install CD is giving me the "Windows cannot be installed to Disk 0 Partition X" details ->"The selected disk is of the GPT partition style."
Here are the partitions
My questions are: At this point I don't mind to have only windows 7 installed or if this situation is salvageable a dual boot then I don't have to remove the drive to copy the docs. I can just boot into 7 (which is what I mainly want to use) and just have access to Windows 8 partition from there to access my docs. I would prefer not to pull the drive out if I can avoid it but only if I know for sure what I am doing.
Second question : I believe partition 3: 489GB is the newly created one and Part 4 OS would be the Wind 8 partition. How can I know for sure that this is the wind 8 partition?
If I format the partition 3: 489GB will windows now allow for windows 7 to be installed?
Is there any way I can fix windows 8 partition to boot?
Lastly the basic question is how do I fix this error so that I Can install windows 7?
I don't have any pre-created OS discs of Windows 8. My current laptop is a toshiba win 7.
I have a new laptop with Windows 8 and I really like it. I also have an older Dell Inspiron 1521 with an AMD 64 bit processor, 4 gig of RAM and a 160 gig SSD. It runs Win7 just fine and I believe it will run Windows 8. My new laptop came with 8 installed so I don't have a box to check the low end specs for running 8. I have Linux on it now and I would like to run both. It boots in to Linux in 20 seconds, about the same time as my new Windows 8 laptop.
Hey I just got a brand new Dell Inspiron with Windows 8 (got it yesterday). In the power options I have the settings set to sleep when closing the lid of the laptop, but the computer seems to always turn off. When I open the lid, my computer is completely off and I have to press the power button to turn it back on and wait for windows to reload.
This is not a battery problem as it happens even when plugged in. I have also tried using the command prompt "powercfg /hibernate on" but it hasn't fixed anything.
I own dell inspiron 14z and i tried to install windows 8 on the 32SSD drive, i turned SATA controller to AHCI and installed the OS. Windows was booted ones and it was all fine but when i restarted the computer it consistently led to the screen "your pc ran into problem and needs to restart...." I tried turning back to ISRT and same, I reinstalled windows and turn the acceleration of but after installing the driver an error was occurred says "your computer does t meat the minimum requirements....".
I turned back to ISRT and tried to install the windows again but it could not find the hard drive even after browsing through usb (it was loading and loading but didn't find anything) and now i really don't know what to do...
I have a Dell Inspiron One 2330, which had Windows 8 Pre Installed, one fine day it stopped booting windows 8...
No matter, I had the recovery media... I made a full system restore... and nothing... it still does not boot.
Black screen after windows logo.
Dell Diagnostics accused no trouble whatsoever, all the tests performed successfully.
After a lot of tinkering, I managed to go back to Windows 7, the system runs fine, but I am running a trial license of Win 7, as I have not yet bought a license (I actually tried restoring the system using the Dell generated backup disks AND the Windows 8 OEM Disk, provided after those did not work).
What could be preventing Windows 8 from booting, since neither the installation fails, nor the HDD acuses any problem?
I have an Inspiron One 2305 All in One with touch display and was planning to upgrade to Windows 8. However, I just noticed on the Dell Support site that they do not support the upgrade, and thus, don't recommend owners of this computer doing the upgrade.
I purchased a dell inspiron 5521 a few months back but i didn't get any windows 8 CD with it. I have to reinstall my windows, but when i try to do it with my friend's original windows CD, error says product key entered is different. I don't even know the product key for my windows 8.
I'm trying to figure out if my Dell Inspiron N4010 has full compatibility with Windows 8. I downloaded the Windows 8 Upgrade Assistant. The two issues I have are Secure Boot and was touch capabilities my Dell Computer has if I decide to upgrade to Windows 8.
I am using Windows 8 on Dell Inspiron N5110 15R laptop. I had to upgrade my BIOS so as to install and use the most recent operating system, Windows 8. I was Windows 7 user and had to clean install Windows 8. In Windows 7, I was very much familiar with safe mode, but today, when I booted Windows 8 into safe mode (Using PC Settings, Advanced Startup etc.), and I selected "Safe Mode With Networking" on restart, and then a blue Windows logo appears with waiting dots circling, and after that the screen is just black, and even after waiting for quite some time, it is still there, as it "freezed"
I've edited the host file with notepad with administrator permissions 192.168.118.129 localhost But localhost is still resolving 127.0.0.1
I am not using a proxy. I had McAfee (Firewall, antivirus) but I uninstalled it. I don't have any program like box.com / dropbox, IIS, Apache installed yet. I tried to temporary disable some service but without success.
Since I've updated to 8.1 my laptop is taking a long to boot up and when it finally does load it's slow as hell.
I'll then be playing Football Manager and when I hit the windows key to go back to my desktop it freezes. I've tried opening task manager and that freezes too, the only thing that functions properly is the metro screen.
I thinking it's a compatibility issue with a program that's causing it.
Specs: Dell Inspiron 7250 Intel Core i7 3612QM @2.10GHz 6gb RAM Windows 8.1 Pro
Yesterday, I restored my Inspiron 15 to it's factory settings. Post-reset, I installed all drivers for Windows 8 directly from the Dell website except for the AMD driver which I took from the AMD website (just wanting to get the latest directly from the source, I guess). I also used that "Dell Detect" thingy to make sure I have all the latest drivers for everything.
After installing, everything worked great, but I realized that when the display turns off / when I shut down the laptop / when I close the lid, it does not turn off the computer or hibernating it or making go to sleep - it just keep running but there is no display, total darkness. Trying to press the power button / F4-F5 / any other button-pressing related solution did not work, only hard-reset.
Googling this issue, I found that it is very common, and many people with almost brand new Dell laptops, just like me, have encountered the same problem. In most of the solutions offered it was said that doing so would cause the system to mainly use the Intel Graphics HD card and not the AMD, meaning that for games and graphics, the AMD won't matter, which doesn't seem to be fair after paying extra exactly so I can have a dedicated card.
Either way, I started with the first which was using Windows Update. After checking the Windows Update updates list, I saw 2-graphic card related items - something called Graphics Adapter WDDM, one for the AMD card and the other for the Intel Graphics HD. After installing this update, I realized I can successfully turn off the laptop.
Once I turned it back on this morning, I got a pop-message:
I then realized that it just simply doesn't see/use/detect the AMD card. This is how my AMD Catalyst looks right now:
Looking at Everest, you can see it only sees the Intel Graphics HD:
However, device manager is still listing the AMD card as if it's properly working:
And if you look at the event log, you can see that initial driver was installed right after the Windows 8 fresh install I made a day and a half ago, and then there's other events, last night, around the time when I installed the Windows Update thingy: