Debugging :: BSOD - Bad Pool Header And Page Fault In Non Paged Area

Mar 26, 2014

Basically about 3 weeks ago I had some computer issues, I figured it was a good time for a couple of upgrades so I replaced the Motherboard, Processor, Power Supply, and I had my Video Card RMA'd by EVGA (excessive coil whine)

I formatted the hard drive (it was a 300GB partition of a 1.5 TB Raid 0) and reinstalled windows 8 to the computer, everything seemed fine for about a week, I took my computer downstairs to hook it up to a TV so my family could watch some Hulu on the big screen and my computer started getting BSOD every few minutes.

I was unsure as to what was causing it so I reinstalled windows again. After the install I was still getting BSOD... so I went out and bought a SATA 120GB SSD and put it in as the primary Hard Drive and installed windows to that drive instead of onto the Raid partition. Same thing, more BSOD...

At this point I have reinstalled 4 times, I tried allowing Windows to fully update everything and tried turning all updates off and manually installing everything myself. More BSOD both ways... in fact at this point when I try to manually install the NVidia drivers they just Fail during the install and wont finish...

Given that the BSOD seem to be either Page Fault in Non Paged area and Bad Pool Header I figured it might be the RAM and ran a MemTest over night, unless I am reading it wrong there were no errors:

My current system specs are:

Full version Windows 8 Pro (not upgraded to 8.1)
Intel i5-4670 CPU (about 3 weeks old)
Gigabyte Z87X-HD3 Motherboard (about 3 weeks old)
2 2GB Corsair 1333 MHz DDR3 RAM (about 5 years old)
EVGA Nvidia GTX 580 3GB video card (just got a RMA replacement about 3 weeks ago)
SoundBlaster XFi PCIE card (About 5 years old)
PCI 4 Drive SATA Raid Controller
120GB SSD Hard Drive (about 1 week old)
4 500 GB Seagate Barracuda single platter Hard drives (SATA, about 3 years old, 1 single and 3 in a Raid 0 Setup)
Corsair TX 650M Power Supply (about 3 weeks old)
DVD RW Drive (SATA, about 5 years old)

So, based on this wall of information, I am suspecting one of 3 things:

1. Might be corruption in the 8GB Thumb drive I am installing my Windows 8 from. ?

2. Might be something with drivers on the computer... after 4 clean reinstalls I don't see how this can be totally it but...

3. Some other hardware on my computer is causing the issue:

- On board sound conflicting with the soundblaster?

- RAID controller?

- Bad GPU / VRAM?

View 9 Replies


ADVERTISEMENT

Debugging :: BSOD Page Fault In Non Paged Area When Waking?

Apr 30, 2014

I'm getting a BSOD every time i wake my machine from Hibernation or Sleep.

Running Windows 8.1 on Lenovo Thinkpad e540 that is about 2 months old. I'm a developer so have lots of different dev tools installed but it only started happening a week or so ago.

View 1 Replies View Related

Debugging :: Win 8.1 BSOD (Page Fault In Non Paged Area) After Sleep

Nov 4, 2013

I started having this BSOD after upgrading to win 8 and it is still persist after upgrade to 8.1.

it happens every time I wake the system from sleep. How to pinpoint what triggering it?

View 3 Replies View Related

Debugging :: BSOD (Page Fault In Non-paged Area) After Waking From Sleep

Sep 15, 2014

I just had this "page_fault_in_non-paged_area" error show up on a blue screen. It happened right after I woke my laptop up from sleep mode.

View 3 Replies View Related

Debugging :: Windows 8.1 X64 - Page Fault In Non-paged Area

Sep 15, 2014

I've had this problem for a few days now and I've been trying to figure out how to fix it, but I'm beat. Here's my SF_Diagnosis logs!

Anyways, I get the BSOD whenever I shutdown or restart my computer, which it'll then restart my computer. In order to turn it off, I have to hold the power button.

[URL]

View 3 Replies View Related

Debugging :: BSOD Page Fault In Nonpaged Area On Restart?

Sep 15, 2014

I have been getting the infamous BSOD when restarting my laptop with the error message of "page fault in nonpaged area". I have a Toshiba Satellite laptop with an intel i3 2.40ghz processor, 6gb of ram and a 500gb hard drive.

It mostly happens when doing a system restart but occasionally happens

when booting up after the system has been shut down, I have uploaded the zip file that I got from running the SF Debug tool.

View 7 Replies View Related

Debugging :: BSOD For Windows 8.1 - Page Fault In Nonpaged Area

Jun 7, 2014

I recently bought a lenovo 11s with the i5 hashwel and i have been getting a few errors.

Every time I shut down the laptop and close the laptop over, when i try to start it again the BSOD error message "Page fault in nonpaged area (rtwlan.sys)" appears.

I have checked my event viewer and the critical message is a kernal 41 error. - Am not sure if this data is needed but more data rather than less am i right? - the error in event viewer as follows:

- <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
- <System>
<Provider Name="Microsoft-Windows-Kernel-Power" Guid="{331C3B3A-2005-44C2-AC5E-77220C37D6B4}" />

<EventID>41</EventID>
<Version>3</Version>
<Level>1</Level>
<Task>63</Task>

[Code] ......

I have updated all the drivers i can via lenovos website and using the automatic search on device manager, all of which they say are up to date.

I have checked a possible cause being the bridging between my wlan and wifi but this doesn't exist i don't think.

View 3 Replies View Related

Debugging :: Page Fault In Nonpaged Area - Crash After Hibernation

Sep 22, 2013

For the past few days, my laptop has been crashing upon waking from hibernation. I initially thought it was a trojan or virus, but after poking around more I think its either a HD or driver issue. I installed Who Crashed and Blue Screen View, which mostly return ntoskrnl.exe, but have also thrown in tcpip.sys, AMPPAL.sys, and usbhub.sys. Asus Install seems to think I'm up to date on all the drivers, but after looking at some of these files, I'm not so sure. Dumps attached.

View 9 Replies View Related

Debugging :: BSOD At Each Launch (Error In Non Page Area)

Sep 15, 2014

I update my PC on Windows 8.1 six month before, I works without any problems. And from two week ago I got a BSOD at each launch of my computer, I just need to shutdown him and it start normally but it took almost ten time longer.

View 5 Replies View Related

Maintenance :: Paged Pool Memory Constantly Increasing?

May 4, 2014

I'm Running Windows 8.1 Update 1 Enterprise.

custom built machine :

I7 4770K
32gb ram
Samsung evo pro 256gb ssd
2x gtx 770 sli

the installation was done around end of january, i don't have much running on that computer but games (i have another system for work)

The issue i have is the Paged Pool memory after system is up is at roughly 250mb but keep increasing around 1-2mb per sec and never stops, after roughly 1h uptime, i'm already at 2gb.(after 1day uptime yesterday, i was at 56gb). The non-paged pool is however never an issue and sits between 150mb and 250mb (i would say normal values)

i've read about disabling NDU, disabling killer networks application (my network driver) and many other things but so far still no luck.

View 9 Replies View Related

Debugging :: Power Driver State Failure And Page Pool Memory BSODs Here

Jul 27, 2014

New to the Forums, but not new to these errors. been having them for a while now, it's one or the other and happens about once a day or so, but with the fast restarts and such it never sets me back too far, but I still wish to fix this all.

Included is the SF file for your looking purposes.

View 1 Replies View Related

Debugging :: BSOD Crash Win 8 64 Bit 3 / 4 Times A Day Minimum - Bad Pool Caller

Nov 16, 2013

I've had Windows 8 for more than a month now but didn't have any BSODs. These started like 4 days ago. They happen about 3/4 times a day, minimum. I have attached my SF Diagnostic Report

The error it gives me on the BSOD is 'BAD_POOL_CALLER'

View 3 Replies View Related

Browser Cause Non Page-pool Leak

Sep 15, 2014

Like the tittle states is it possible for a browser or browser extension to cause memory leak in the non page-pool.

A couple of of day ago I switch over to Opera and had memory leak in the non page-pool that paralyzed the machine till I rebooted.

Asking cause a few days prior I was messing around with a few of my drivers and I have a new motherboard coming and was thinking of just popping the hard drive on without doing a fresh install of windows, since I have an upgrade version of Windows 8.

View 5 Replies View Related

Dell :: Page Fault Error In Windows 8 / Restarting With Blue Screen

Dec 29, 2012

I'm experiencing a problem after installing Windows 8 on Dell Inspiron N7110.

When I leave my laptop on for a while, it restarts because of a blue screen with the error: 0x00000050; PAGE_FAULT_IN_NON_PAGED_AREA

It only happens when the laptop isn't used but is still on. When I'm working on it this error doesn't occur.

I checked RAM and HDD with Dell Support Center PC Checkup (even RAM stress test) and it shows no errors. Besides the HDD is new, as my old one broke and Dell replaced it.

I updated all my drivers from Dell's Website, so they all supported by windows 8.

View 2 Replies View Related

Debugging :: BSOD Kernel Data In Page Error?

Sep 15, 2014

I keep getting blue screen all the time, its so frustrating, ive reinstalled for 2nc time now and this error doesnt go away. I dont know what to do, i dont know if it is a hardware problem or a software problem, ive run RAM and HDD tests and passed both. And everytime i get blue screen,the bios reverts to some old settings ive had.

View 3 Replies View Related

Debugging :: Random BSOD Kernel In Page Error And Critical Process Died

Mar 29, 2014

I just bought a Lenovo Flex 14" and have been getting BSODs out of nowhere, usually after a while of surfing the net.

I thought the ram is flawed so I went back to the store for a new ram and the BSOD problem halted for a week but now it's coming back again.

I have attached the dump log using SR.

View 5 Replies View Related

Debugging :: Getting Random BSOD Kernel In Page Error And Critical Process Died

Dec 9, 2013

I'm getting random BSODs lately. The errors say

"Kernel IN Page error" and "Critical Process Died"

After reboots, some of my software gets reset (i.e. I need to relogin to chrome to get my preferences/plugins back)

View 9 Replies View Related

Debugging :: Bad Pool Caller In Windows 8.1

May 23, 2014

I saw this BSOD for the first time last night. I don't know exactly how it happened: my sister was using my computer to edit some photos from her travels on Photoshop. She shut it down. I opened it up and pushed the power button a little while later. After the HP loading screen, I saw a BSOD for "Bad Pool Caller."

I have seen some issues due to an outdated graphics driver. When I updated to Windows 8.1, I began seeing delays upon wake up and entries in the Reliability Monitor for hardware errors. I've tried updating my graphics drivers but since I use switchable graphics, it is actually extremely difficult to do so. HP's drivers don't allow me to open them and Leshcat's drivers have failed, too. That is why I have given up on updating them.

Minidump file is attached.

View 4 Replies View Related

Debugging :: System Crash With Message (Bad Pool Caller)

May 3, 2014

My system has crashed several times and today I find out that it dumps a file that can figure out the cause of the crash. I have attached the dump file ...

OS : Win 8 64bit
System : Alienware 18"

View 2 Replies View Related

Windows 8.1 - Bad Pool Caller

Jul 16, 2014

I have an acer computer running windows 8.1 i left a file to download, when I came back I saw a bunch of error messages talking about the memory/ram, so I restarted and got a windows 8.1 blue screen of death. Saying BAD_POOL_CALLER. Right now it says it's collections error info and it's at 100% and it is still my computers fans are loud.

View 5 Replies View Related

Storage Spaces Can't Add Drive To Pool - Incorrect Function

Jul 21, 2013

When adding an initial drive to a storage pool I get the error "incorrect function"

System: Proliant ML110 G4, Windows 8 64-Bit, 4GB Ram

I have a 160GB drive installed on the motherboard's controller which hosts the OS. I've installed a single 2TB drive on a 2 Port PCI Express Internal SATA II Controller Card (JMB36x). As soon as I create a pool using the 2TB drive I get the error "Incorrect Function" and the drive becomes RAW.

The drive id's are unique. It's worth pointing out that the system without the new controller can only support 2TB max of SATA drives, but this is bypassed by the controller card I added?

Get-PhysicalDisk | format-list FriendlyName, UniqueId, ObjectId, BusType

FriendlyName : PhysicalDisk0
UniqueId : 2039374232333633
ObjectId : {af665d5a-f225-11e2-be77-806e6f6e6963}
BusType : RAID

FriendlyName : PhysicalDisk1
UniqueId : IDEDiskST3160812AS_______________________________3.AJL_5&3dc7918&0&0.0.0:risa
ObjectId : {af665d5b-f225-11e2-be77-806e6f6e6963}
BusType : ATA

I'm also worried that the 2TB drive is showing up as RAID not SATA on the controller.

View 9 Replies View Related

Update Fault - Failure Configuring Windows Features / Reverting Changes

Sep 16, 2014

My laptop is 2 days old and I went to do a windows update which I had to do and just says 'failure configuring windows features. reverting changes, don't not turn off computer' this also is happening with my other laptop I think it's a bit of a joke that it doesn't work on a brand new laptop..

View 2 Replies View Related

Moving Windows To Visible Area

Feb 1, 2013

Windows 8. In windows 7 when I switched from dual display to single display all windows stayed exactly where they were so when I switched back to dual display everything was were it supposed to be (i.e. chat windows + music player on side display)

In windows 8 each time I do that (switch from double display) all windows from second display are moved to the main/only one and upon switching back they are not moved back which is...

Can I somehow make windows 8 to behave like win 7?!

View 2 Replies View Related

Deleting Notification Area Icons?

Oct 3, 2013

I have so many in there that are listed from software i tried out and no longer use but the name is still listed there that i do not want listed. Is there a way to delete them for good?

View 6 Replies View Related

Windows 8.1 Pro X64 - Notification Area Icons Disappear

May 6, 2014

I am running Windows 8.1 Pro X64. Recently I have noticed that Notification Area Icons for some apps have disappeared.

A reinstall or a repair install sometimes brings them back but then they disappear after a while, and usually after the next reboot.

Have checked forums for the affected products and the only solution offered there is reinstall or repair install. I very much doubt that this issue is down to the products. It is almost certainly a Windows problem but of course Windows Tech Support offers nothing other than the usual banal references to largely irrelevant "how to" articles.

View 7 Replies View Related

How To Put Icons Back From Taskbar To Notifications Area

Jun 21, 2014

My "Notification Area Icons" was not working right, so I opened it and checked the box "show all icons and notifications on the task bar" and it did.... Now my task-bar is crowded with all these icons and so I must put them back. The problem is, I have tried clicking all over the task bar but can't find the tool/option to do it.

View 1 Replies View Related

Delete Unused Icons From The Notification Area?

Feb 9, 2013

I am running windows 8 and I would like to delete unused icons from the notification area. Can this be done?

View 1 Replies View Related

Maintenance :: Notification Area - Show Icon / Hide?

Aug 9, 2014

I just installed mouse software on my 8.1 Pro laptop. The software starts every time I start my computer and shows an icon in the taskbar. There is one very annoying thing that it does, when I first login to my computer the notification icon for the mouse software pops up a window saying that it's running:

I opened Customize Notification Area to see if I could turn off notifications BUT keep the icon there (so I can right-click it and open the software).

I noticed there is no option to "Show Icon And Hide Notifications".

So the only way i can keep that annoying popup message from appearing every time I login is to hide everything. But then, as I said above, I won't be able to right click the icon and start the software.

Is there a way I can show icons but hide notifications?

I noticed when I was looking at the custom notification area window that there were entries for programs that I no longer have on my machine:

Is there a way to cleanup/remove these?

View 4 Replies View Related

Security :: Windows Defender Notification Area Icon?

Feb 20, 2014

Lenovo laptop with Win 8.1. I uninstalled the pre-installed McAfee anti-virus with:

- Uninstall McAfee in Programs and features
- Reboot
- Run the MCPR McAfee uninstall utility
- Reboot (many times)

With that Windows Defender shows it is running, but there is no Icon in the notification area.Should there be an Icon in the Win 8 notification area, like Security Essentials in Win 7?

View 9 Replies View Related

Preview Area In Folder View Similar To Windows 7?

Dec 26, 2013

How can i make windows 8 show this when clicking an item, i could not find a simple option unless i am loosing my vision

View 5 Replies View Related

Apps / Software :: Get Rid Of OneDrive Icon In Notification Area?

May 8, 2014

I disabled all of the OneDrive sync settings on my PC and checked the Startup programs, still OneDrive icon shows. How to get rid of this?

View 8 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved