Audio :: Line In Missing From Volume Mixer After Reboot
Jun 11, 2014
I have an audio source connected to Line In and I use the volume mixer to un-mute the input when I want to listen to the audio from that source. I recently started having a problem where after re-booting Line In does not show up in my volume mixer and I do not hear audio from the Line In Source even though I have listen to this device active. (during boot up I do hear the audio for a fraction of a second)
To get Line In to work and show up in the volume mixer again, I have to go to manage audio devices under control panel and select the record tab. from there I can see Line In and I see that it is set as the default device and I can see that there is audio based on the indicator bars to the right of Line In. I then have to go to the Listen tab for Line In and uncheck "Listen to this device" and click on Apply, then Check "Listen to this device" and Click Apply. After doing all of this the Audio can be heard and Line In appears on the Volume Mixer until the next reboot where I have to perform those steps all over again.
I have the latest drivers and all MS updates for Windows 8.1 on a Gigabyte GA-Z87X-UD5H Motherboard with Realtek R3.87 Driver dated 5/13/2014...
I'm using a Logitech 35 headset on Windows 8.1 64-bit and all drivers are updated but when i want to adjust the volume, the volume mixer becomes unresponsive and stops working and my headset stops receiving sounds.
I got a problem on the Volumer Mixer. All started yesterday after i decide to install my new speaker...
Basically before i could control all the computer volume but now when i go to volume mixer there is a lot of stuff open and then i need to control each volume for each application...
I want to be able to remove all applications and be able to put louder my volume with only one slider. Here is a picture of the problem:
The Device is my Headset a Logitech G930. when try to turn the volume louder on this slider:
Doesn't get louder like the headphone used to get.
Basically I have an ASus ux301la (zenbook infinity) and i noticed that after installing Displaylinks software (port replicator software) my default sound device was called (USB AUDIO) and that my Realtek sound device kind of went missing (no sound devices on the playback tab in the sound settings). I had no backups at teh time as its a new laptop and i really dont want to re-install 8.1 from scratch as it took me over a day to configure this thing to my personal config.
So I uninstalled the diplaylink software and uninstalled/reinstalled the sound drivers from the asus site and each time i did so it would create a new sound entry, hence all teh duplicates. Now i still have a problem because although sound works, i have to manually select the correct playback device in VLC player and I cannot see any sound devices in the playback tab on SOUND settings.
How do you turn your microphone port or line in, to a headphone port or line out port. For a while I would plug in headphones into the mic port and it would bring up a dialog saying I could change it to another headphone port but it never worked. Now it doesn't even pop up. I want this so when I go on long trips my girlfriend and I could watch a movie together using 2 pairs of headphones.
I am trying to record from a cassette player on to my hp envy h8-1500z. I have a cable going from the headphone jack on the player to the blue line in jack on the pc. I have gone to the recording devices and have the line in jack enabled. That is as far as I can get because it says it is not plugged in? I have plugged it into the mic jack and it recognized that. I have tryed updating the drivers to no avail.
I've read that you have to go to the microphone, double click on it, go to the levels tab, and move the lever all the way up, as long as the boost lever. I don't have the boost. Only the microphone is present as you can see in the screenshot. That doesn't work.
I just downloaded Windows 8 last Thursday so all of my updates are installed. I updated to the latest drivers for my sound card thing, which I guess is intergrated. Now, before you tell me it's my mic, before Windows 8 I was using xubuntu until I could afford Windows 8. My microphone was fine. It picked up great. I could hide it behind my monitor (which is atleast 3 or 4 feet away) and it would still pick up fine. Now in order for it to pickup my voice like it did behind the monitor I have to have it literally 1 cm away.
I've been having random volume fluctuations with things like youtube and iheart radio, as well as the occasional games. I've been searching the forums for a solution but the closest i can find is on the W7 forums, (Volume level continuously changes - Windows 7 Forums), which is the same problem I'm having with windows 8 pro. The last post on that thread is from September of 2012, so really I'm just curious if any new info or solutions have been made available. Like the op in that thread I as well disabled my communications and turned of the enhancements. I also uninstalled my audio drivers, restarted, and when it rebuilt the drivers they were newer than the ones i had. (Realtek 6.2.9200.16497, current driver) Yet still the problem persists. Team Speak 3 is the only web voice chat service i use, but that's only on when running a game.
So instead of explaining what I'm looking at right now I'll post a picture here:
So as you can see that bar there is putting my volume automatically up to 100% every single time I touch it. Also, recently this has made the computer unable to drag the top or side or have any Windows 8 features available this includes both Windows buttons on my keyboard. I have tried cleaning my keyboard as that seemed to work last time on fixing this problem for maybe a month, however it worked for only an hour this time. It also seems note worthy that I cannot capitalize these letters at all: z x c v m , . and then I can't capitalize certain letters with certain shift bars so I can capitalize s with my left shift but not my right this happens with many other letters too but the ones I listed above cannot be capitalized at all.
I cannot stand having to hold the "Function" key plus the volume up F12 or down F11. I want to remap some keys to be a direct volume up and volume down.
I am trying to install Windows 8.1 onto a new PC a clean install. I boot from UEFI CD/DVD Drive with the windows 8.1 install disk in it and it gets to the "Press any key to continue" screen, I press a key and it just restarts my computer. Then I try to boot from just regular CD/DVD Drive it says Missing BootMGR.
So, the system volume in the system tray goes from 1-100. 1 is comfortable. 3 is loud. 6 is ear-splitting.
Is there anyway I can redefine the values for the system volume and set the maximum to like... 10?
Any time I hit the volume buttons on my keyboard to lower the volume, it goes from 1 to 0 and I can't hear anything, so I hit the volume up button and it goes from 0 to 3 and it's way too loud.
Right now, I have the volume set to about 3 most of the time, with individual apps' volume controls set really low (like a game set to volume "0.5" out of 100).
This is just ridiculous. There must be a way to redefine the value for the system volume. Some settings file I can edit or something, if not a nice GUI method.
My new laptop seems hardwired to think that if I set the volume to 20, so long as I have headphones in, I want my volume at 20 for all sounds, ever. This makes music which varies from quiet and loud feel extremely alien and even ruins the feel of some videos and games. But it's most notable when watching a youtube video and I change the volume. Turning it up makes the video louder for a split second before returning to what it was, turning it down? Well, that works for a few seconds and returns to being too loud.
My new laptop uses HP Beats Audio. While I'm currently blaming Windows 8 for this problem, it'd be silly not to mention it. Unfortunately, a google search didn't get me any answer for beats either except how to uninstall it.
This doesn't happen on my old Laptop, which runs Windows 7 and appears to lack a special audio device. Looking online for a fix has only returned me nonsense about Windows 8 reducing volume for communications devices (a feature which I have off). In my search, I found this bit of information from Winsupersite.com:
"Incidentally, Windows 8 new Metro-style volume controls lack many of the more sophisticated controls that are available via the desktop. There's no way to control the volume of individual Metro-style apps, for example, and that's true of both the new Metro volume controls and the legacy desktop interfaces. Instead, the system automatically controls app volume, muting or lowering the volume of background apps when needed."
So... I suppose in short what I need to know is, how do I turn this "feature" off?
When using my computer and streaming netflix, i generally use my HD tv as my video card has audio built in over HDMI and i use it to stream movies to my HD tv ,with netflix app for windows 8. but on some movies the volume is totally Low and i have to crank my tv to here the voice leaving me with very loud music when it comes on. is there a solution to fixing this? i make my TV volume default when i watch netflix. How to make it louder. I have seen this thing called loudness equalization under enhancements on the HDMI audio would that do it or would it make more noise then do any good?.
Alienware x51 with windows 8 pro and media center. PNY GTX 660TI video card.
Whenever I increase the volume the sound is really horrible, like from cheap $3 speakers. The sound is NOT clear at all. I tested the same files (mp3, FLAC) on another device and it is just great.
Here's my setup:
OS: Windows 8 - all updates
Soundcard: Asus Xonar D1 interne PCI Soundkarte 7.1, Digital Out, Dolby Technik, Eax, 192kHz 24bit, Low Profile - newest driver
Mainboard: Intel DP55WG - onboard sound disabled in BIOS
I recently purchased the Polk Hampden Speakers. For some reason, the manual volume control built into the speakers themselves doesn't affect the volume level. The only way I can adjust the volume is by using my computers volume control software (the little white speaker in the bottom left of Windows 7/8). I am fairly certain the hardware volume control isn't broken, because when I first plugged them in ( a week or 2 ago) they worked fine. It wasn't until I disconnected/reconnected everything from my computer when I installed a new desk that this problem started.
However, even the software volume control isn't working properly either. In particular, when I go into the mixer to see the volume levels for each application, if I adjust the main "Device - speaker volume" it won't alter the specific applications volumes accordingly. Like, I can reduce the main - device speaker volume all the way to zero (not muted) and the applications will still have the same volume level as they did before I adjusted it.
Finally, even my keyboard bindings to the volume control are whacky. I can still adjust the "main - device speaker" volume with the keyboard, however since this "main - device speaker" volume no longer influences the individual application speaker volume level it is pointless to do so.
I have tried disabling all other sound drivers/sound hardware, but it doesn't work.
I have tried uninstalling/re-installing the USB drivers for the Hampdens which didn't work.
I have tried restarting the Microsoft Services responsible for audio output recognition which didn't work.
I have tried downloading the audio drivers specific for my motherboard, but that didn't work.
Additionally, applications sometimes don't recognize the speakers. If I start the application before turning on the speakers the application won't recognize the speakers unless I cycle through the speaker output modes (the little button under the volume knob) and get back to USB mode. Otherwise, I have to completely restart the application. This issue isn't as big of a problem as the manual volume control not affecting the volume output of the speakers.
I have tried uninstalling all my audio devices/drivers, but this doesn't seem to work. They just instantly re-install it appears.
What I want is actually the opposite of what most people are looking for. I want to install windows 8 on my kids computer but want the volume level to be set at a certain level so the sound is not to high no matter what they do.
I am able to achieve this right now as the desktop is on XP and i have the wave bar set to a certain level so no matter how high they put the volume bar it just stays at a certain level.I have hidden the wave bar so they cannot even get at it by mistake.
The main thing is that I am using a sidewinder X4 keyboard which has the vol+/- so they can easily increase the volume even if I hide the volume tab from the desktop in windows 8, while in XP it remained a certain lvel even if they put it upto 100%.
I have been searching for win 8 mixers where I could maybe have the same type of control as the XP but so far have found nothing.
The volume for media playback is way to low in windows I have tried everything from disabling enhancements, I also have installed SRS HD audio software also with low volume.
An audio booster, or anything that would boost SRS Audio output. I also after using the default driver provided by Windows 8, updated to the newest Realtek HD driver, and still no difference.
Before installing my new Sound Blaster ZxR I had to temporarily use the Onboard Sound of my Asus Rampage IV Black Edition because of a SLI Water cooling component blocking the necessary PCI Port of the former Sound Card ( a Sound Blaster Recon3D Fatal1ty Professional ).
Because of the cracking ( grounding loop? ) I receive during the startup when using 3.5mm jacks ( or 1/4" with the ZxR ) I stopped using them whenever possible and instead started using the Toslink connection on both the Recon3D AND the RIVBE as it electrically disconnects the PC from the Sound System.
Now here comes the Problem: Using the new Sound Blaster ZxR and having it connected via Toslink to my Sound System I'm not able to control the Volume using.. Multimedia Keys on my KeyboardVolume Mixer from the TaskbarEven Muting isn't possible
The only way to change the Volume level from now on has been by doing one of the following four.. Change the Volume level by Hand in the corresponding App itself, not the overall System Volume - Kind of sucksUsing the Hardware Dial on my Speaker System - Hard to reachSwitch from Toslink to Jacked Cables - Startup cracking Also
Switching the default Playback Device from Speakers to Digital Audio (S/PDIF) - Will cause me to loose the ability to run Encoders like Dolby Digital Live or DTS Connect and it's DTS Neo:PC Music Mode feature which, in my opinion, really improves my listening experience as it then uses all my Satellites, not just the front ones.
I'm not sure how my settings were while still using the Recon3D that allowed me to go Toslink while still being able to change the System Volume simply by using the Multimedia Keys of the Keyboard.
When i try to record from my sound card the volume will randomly go up and down when i try to replay it.
When I try to record from my microphone in the microphone input port it gives an odd problem. Whenever I sustain a note it begins to record just fine but after about 2 seconds the volume adjusts down to about 20% of the original and continues to record. It does this in multiple sounds recording software programs. I have skype turned off and no other microphones hooked up. In the communications tab of the sounds menu I have set it to 'do nothing' but this had no effect. It seems like there is some sort of auto volume leveling thing going on but I cannot find where it would be. I have an HP desktop with beats audio not sure about the sound card otherwise.
I want the volume popup bar with the track title information for Windows Media Player, is this possible, perhaps with a registry edit?
I mainly notice it in gMusic app and I've seen the Pandora app have it as well (Whenever I hit the pause button, it will pop up with album art, artist and track info as well as a volume slider) ...
I mainly use Windows Media Player for music though so I'd like this cool feature for that program, it would be very handy when I'm playing a game and I don't want to alt+tab out just to see what song is playing ...
Why I am missing my enhancements tab in the audio properties of my speakers. I want to try and enable "loudness" but it just doesn't seem to be there! I have the latest drivers for my audio, I just can't figure out what I'm missing. Here's a screenshot showing the tab missing.
I have just interviewed a client using the webcam recording function of movie maker. I'm now back to review and edit the video and I don't hear any sound..! I tested it with a short 5 second video of myself before I left and everything was fine.
I had my laptop for about a year now. The problem is after watching 3-4 videos, the sound will not work on the next file. I tried restarting and it worked! But after another 3-4 videos, there was no sound again. Another thing is when I open a music file, it works again. But the cycle just goes on.
Acer aspire v5-551g Conexant high definition audio ...
We are upgrading our office to windows 8, but 1 computer is hardly ever used and is running XP. It will stay with XP, and should not be allowed to go online for security reasons.
All computers are networked, and share printers thru a netgear vpn router. Of cause they all can go online. Question: How can I prevent the XP computer from going online?
I opened the netgear router settings ( http://192.168.0.1 ), but can not find any setting blocking a computer from going on line.
