I need to flash some roms on a graphics card and a disk controller card, but both require the use of a 'boot floppy' (i'm adding that in quotes as this is totally alien to me!
I suppose this means some sort of ancient dos thing!
I've really tried against all odds to eliminate floppy and serial / PS2 devices from my life, and now I've achieved this, and my loft is far too dusty to be crawling around in trying to find such things again!
Could I create this dinosaur relic on a USB stick, and if so, how does one go about it?
I tried making my usb stick bootable as I did in the wonderful thread on this forum to install RC1 and it worked a dream, but i'm guessing this isn't the same thing is it .
I was trying to make a dual boot system and came across this problem. I have two HDDs, one with Win XP in it and other in which I am trying to load Win 7. I made a primary partition (NTFS) through Win XP in the second HDD (labelled it I) and started loading Win 7 through a bootable pendrive. Things went fine till the installation was complete. Then, when I restarted the system, there was no Boot manager screen, Win 7 just started booting the system ! When I looked into the file system, the partition in which Win7 was installed (I: ) was labelled to C (whereas C was the name of the partition in which Win XP is installed !).
I have two queries:
1. Is it possible to install Win 7 in drive labelled I only (I understand that physically it is the same drive in which I had intended to install it). That's because a small sys. reserved folder is getting created which (most probably) is storing the swap data.
2. How to get the boot manager screen option ie. get the selection screen in the beginning to select b/w XP and 7.
in my PC there are some drives with RAID0 arrays and from little time I have bought a SSD for Operative System (Windows 7).in your opinion (on the BIOS) is it better making the Boot with SSD or with another drive with RAID0?
I want to make dual boot because of battlefield 3 does not support XP. So, I have the disc with partitions C and D. There is Windows XP installed on D. I dont want to lose my data from D so my question is if i can format the C partition and install Windows 7 there without losing the data on D.
I decided to use DigitalRiver to download my copy of Windows 7 and I will NEVER use them again. They have no phone or tech support; the only way to contact them is by email, in which a response can take many days.
It took me over 10 hours to download their download manager. While the DM seems to work OK, I keep getting the same error message near/at the end of the unpacking:
"We are unable to create or save new files in the folder in which this application was downloaded. Please check the folder properties to make sure that you have security permission on the folder to write files and that the folder is not read-only"
So while I wait for some intelligent response from them, I'm trying to create a bootable DVD but I'm not having any luck. I've tried using BurnAware and UltraISO yet every time I reboot, the DVD never boots...any ideas on exact steps to take?
I have an HP desktop computer that I just bought an SSD for. I made the "recovery media" disks, I'm assuming that's the OS backed up? I want to make the SSD my boot drive. I put in the disks and unplugged the HDD and plugged in the SSD and I'm at a screen called "Recovery Manager". Do I do the "factory reset" to install the OS on this SSD?
I just got a new hard drive after the old one failed. I have made a bootable USB Drive and put Windows 7 On there. Im looking though my Boot options and i cannot find USB in it. My motherboard is an Asus P5Q-SE2.Is there anyway i can Install the OS from the USB as my DVD Drive is Dead.
I wanted to create a new partition to try out linux. So I decided to shrink E: by 20 GB. I then formatted the free space into a new drive by right clicking and creating new simple volume. I was warned that the drive would be made "simple", but not knowing the implications, I went ahead with the procedure. Now on rebooting, windows won't load. I had made a repair disc, so was able to use it to check for any start up errors. It reported none. Moreover I used "diskpart" through cmd to find volume c: is dynamic.
im usin 2tb segate new hard disk sir..in my system i cant able to boot my os and also my hard disk...its showin that hard disk boot failure insert system disk press enter ...i restarted many times its sayin the same problem...in my gigabite mobo bios my hard disk is not get detected sir....the problem is that wen im installin the new os for 2nd time its all went nice only sir but at the completion of the os it wil ask for the user name and password but in my system its frozen sir fully of black screen and i cant able to do anythin so i restarted my system from that im gettin this error as hard disk boot failure insert system disk press enter.....that my new hard disk and all of my data is in that hard disk only..this problem arises wen im installing the os for 2nd time sir.
I woke up this morning, and I found that my computer was displaying this message"Disk boot failure, insert system disk and press enter". There are a ton of needed documents on the computer, and I'm hoping that they can be saved some way.
I've been having this error even after reformatting and reinstalling Windows 7 on my desktop. I've done reformatting / reinstalling Windows 7 several times, yet the problem still occurs. I'm thinking of my HDD as being corrupted or messed up. The problem occurred after I accidentally hit the CPU when I was stretching my foot. The screen froze after that. Upon rebooting it, 'Disk boot failure, Insert system disk and press enter' occurs. After I entered the DVD installer of Windows 7, the screen just hangs.
I have been having a bit of trouble with windows 7 lately, namely that it won't start up right. When I boot from the drive normally, it gives me the classic "BOOT DISK ERROR: INSERT SYSTEM DISK AND PRESS ENTER" message.
However, I soon discovered that if I boot from the Windows 7 cd and do not boot from it (By ignoring the "Press a key to boot from CD or DVD..." Windows 7 boots up fine. I've tweaked my BIOS over and over, but the same problem persists. The drive is brand new and fine. What can I do?
My friend bought a new PC and needed to put am OS on it. He put in the W7 disk and the error message 'disk boot failure insert system disk and press enter' appeared before installation was shown. He has tried changing around BIOS and it also recognises the hard drive and DVD/ CD ROM drive. Here is the specification he was given:Case : CIT Reaper Black Mesh fronted Tower CaseMotherboard : Gigabyte 78LMT Motherboard TechnologyCPU : AMD Bulldozer FX 4170 4.2ghz 8mb CacheHard Drive : 1tb Sata Hard DriveMemory : 8gb DDR3 1600mhz MemoryOptical Drive : 24x Dual Layer Sata DVD WriterGraphics Card : Nvidia Geforce GTX 650 2gb GDDR5 With HDMIPower Supply : 750 Watt Branded Power Supply Also, he has tried booting BIOS in different order
When starting the computer, I keep getting "Disk boot failure, insert system disk and press enter". Nothing works other than putting in the boot disk and hitting the restart button on the tower. Then it will boot up and run fine. But how do I stop it from having to have the disk in order to load? Checked in the BIOS and the hard drive is the first load.
So, I need to know if I can install windows 7 x64 via direct boot when I start up my computer it is in ISO format. So like my default boot will be my DVD drive to install it. can I do that with it being ISO format?
I tried to add a new 1TB HDD into my computer. not realizing what i was doing wrong. i just threw it in there no software or anything. now my PC is getting "DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER" and i no longer have my windows 7 disk. is there anything i can do ?
I want to do a 'custom' reinstall on my C: drive. It's clogged with unused programs and it runs very slow.I set the BOIS to boot from HD and CD; neither worked. I purchased a new HD and may want to install it as my C: drive.I set the BOIS to boot from CD; still I get the dreaded message:"Disk boot failure insert system disk and and press enter"I recently installed a new mother board due to the fact it was defective, not as an upgrade.To make it clear I already had Win7 Ultimate installed. On my first attempt to perform #1 I got to the question of which install did I want; I clicked 'custom'. From then on nothing happened, and now I keep getting "THE DREADED MESSAGE".I put my win7 disk in another OSXP computer and it displayed, "This disk is not compatible with this system" so I assumed my disc was not corrupt.I bought my win7 disk legally on line a couple of years ago, and I have used it once. Will that be the problem? I never got to the "License key" so I don't see how it could be?
2 months ago, I installed windows 7 pro with no problems at all. Fast forward to today, I decided to reformat because the boot would get stuck in the middle of trying to boot into windows, it wouldn't flash the windows logo. I didn't think much of it so I just reformatted. This is where my real troubles began.So I reinstall windows 7 pro with no problems (the boot disk is in there the cd drive the entire time) I install my programs and what not and install my updates. All 100% Fine. Then I take out the boot disk and restart again... and I get this error message saying:
Client Mac Address: 00 30 1B BC1F59 GUID: 12973077-FFFF-FFFF-FFFF-FFFFFFFFFFFF DCHP....
Then I press escape, then it says this:
PXE-EA0: Network Boot Canceled PXE-M0F: Exiting Nvidia Boot Agent DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER
So the first time I got this error, I just thought, Oh, something must have happened no big deal, so I reformatted again and again. But I kept on getting the same exact error. It'll load into windows just fine when my install disc is in the cd drive, but when I take it out, that error pops up. *My windows is authentic, each time I have been able to validate my copy.* I have tried installing from my hard drive and from the install disc with same error.*
My current hard drive is dying, so claims Windows and Hitachi Drive Fitness Test. I bought a replacement drive 3TB drive which requires GPT partitioning. I have 64 bit windows and a UEFI motherboard, so I know I can use the drive as a boot drive for a brand new installation.
My question is how do I move the entire contents of my old drive to this new drive and keep it bootable?
I asked on other another site and they suggested I first let the Windows installation disk partition the drive GPT correctly for Windows, then copy the contents of the old drive to the new one. However, another person on that site said that that would break all the symlinks (didn't know symlinks played such a crucial role in the OS) and that I should use a cloning utility that knows how to copy NTFS. Was this person off base, or is it impossible to create a bootable copy of a Windows installation by just copying all the files (this would be from live linux of some type, not Windows itself)? If it is impossible, is there a utility that can copy the contents of a partition correctly, without needing to clone the entire partition table? Also, I have no room to make an image of my old drive anywhere.
Finally, does anyone know if clonezilla can copy an mbr partition to a gpt partition automatically, essentially doing exactly what I need, or will it always copy the partition scheme as well?
I've just bought Seagate Momentus XT 500GB and installed it myself to desktop. Downloaded DiskWizard from Seagate to clone my old hard disk into the new one.
Problem: How do I boot from the new hard disk? I still got my old hard disk on my computer, I'm trying to use it as extra storage, but it's still booting from the old C drive. How do I change it to boot from my new hard disk?
Running Windows 7 Home Premium. For three days now I have seen nothing but the error Boot Disk Failure when trying to boot up.. I can overcome it by putting the IOS 7 disk in the DVD CD drive and let it boot so that I can then run the repair on the computer. I borrowed an OS 7 install disk and the same thing happens. After a series of checking the system I am informed that nothing wrong was found. If I leave the disk in the drive, even through rebooting, the machine runs just fine. If I take the disk out of the drive, I am dead in the water until I put it back in the drive, reboot and let the tests start over again and all is fine.
My father's PC is quite new, with Intel i5200 chip, 4Gb RAM and ASUS motherboard with onboard graphics. About a month ago he experienced random BSODs, he is not aware of any particular program causing them, and the dump files I have seen are all different.
BSODs increased in frequency, so I said I'd take a look at it, reinstall Windows, whatever. Anyway, it took me hours to back up his photos between crashes, and then I found I couldn't boot from HDD or WIn 7 DVD (full retail disk). I get to the Windows did not start successfully, run Repair screen, but it doesn't run it. Likewise from the DVD, it loads the initial files, then crashes to the Repair screen, only to not run it.
Likely culprits? HDD? RAM or PSU? It's in warranty, but I'd like a steer on possible causes before he sends it back, you can never know too much!
I have my serial number that I got from Microsoft a while back and I burned the iso to a bootable dvd however when I try to boot with the burned disk, all that happens is I get a black screen with a flashing cursor at the top of the screen. I left the computer like this for aproximately 2 hours tonight and it never ended up booting up.
I've tried using imgburn as well as magiciso to burn the image to the disk and both of them have made coasters of several dvd disks now.
From what I remember when I first installed Win 7, I was atleast able to double click on the setup.exe program and it would bring up a windows 7 window in vista that was like an installer. However when I try that now, I just get a message telling me that autorun.dll is either not made for this version of windows or it is corrupt. I can't imagine the iso file becoming corrupt from simply sitting on a drive that I rarely use between the last time that I burned the iso image to a dvd and installed Win 7 and now.
Perhaps this is a common issue that somebody here knows how to deal with. Apparently MS isn't allowing any more downloads of the iso so I'm pretty much stuck with the iso that I have an hoping that it's not really corrupt.
I have an eMachines E528 with an Intel Celeron 900 processor. I got the blue screen of death and was able to use the Windows system repair disk to reinstall windows 7. However, while trying to "update" Windows 7 with the SP1 update through the windows update tool, I got the blue screen of death again. This time I cannot boot the computer. I've tried a recovery disk, a system repair disk, a new clean copy of windows 7, and a Partition Wizard bootable CD. Everytime it gets to the point of loading ANY menu, it freezes up and does nothing for hours. I have spent so much time researching and trying things from other forums, and I have gotten nowhere. get a fresh copy of windows on this computer? or get me into the menu that allows me to restore from a system repair disk? I have even tried an "eRecovery" without even going into Windows by pressing ALT F10 at the logo screen as the computer is booting up, and I still get hung up while the application is trying to load the menu options.
I tryed to create a D: since there eas only a C:. After creating 2 partition a was going to merge these to but the result was after that I lost my C: "No bootable device". how to burn a botable f-disk, in swedish if possible.
i watched this video on Internet where this guy had windows loaded on a ddr2 or ddr3 ram disk (i guess you would call it that) and windows booted in less than 4 seconds and programs opened up instantly. i have not one clue how he did it but would this be possible to do and put all of your everyday programs on it? like your web browser, media center, and what ever else you use most often, and you put the rest of your programs on a ssd?
How can I solve the disk check at boost? I have used seagatetool to check disk but the result is PASS, the hard drive had no problem. I have format the disk and reinstalled Windows 7 but disk check still run.
