I was trying to make a dual boot system and came across this problem. I have two HDDs, one with Win XP in it and other in which I am trying to load Win 7. I made a primary partition (NTFS) through Win XP in the second HDD (labelled it I) and started loading Win 7 through a bootable pendrive. Things went fine till the installation was complete. Then, when I restarted the system, there was no Boot manager screen, Win 7 just started booting the system ! When I looked into the file system, the partition in which Win7 was installed (I: ) was labelled to C (whereas C was the name of the partition in which Win XP is installed !).
I have two queries:
1. Is it possible to install Win 7 in drive labelled I only (I understand that physically it is the same drive in which I had intended to install it). That's because a small sys. reserved folder is getting created which (most probably) is storing the swap data.
2. How to get the boot manager screen option ie. get the selection screen in the beginning to select b/w XP and 7.
I want to make dual boot because of battlefield 3 does not support XP. So, I have the disc with partitions C and D. There is Windows XP installed on D. I dont want to lose my data from D so my question is if i can format the C partition and install Windows 7 there without losing the data on D.
I want to make a recovery disc to reset my entire 4 partition dual boot hard drive back to its current state. the recovery would reset both xp and win 7 which i have dual booting. can i make one single image to do this without it screwing up my boot loaders etc? what should i use? 3rd party software?
Did a system restore in Windows 7 and my dual boot system (Windows 7&XP) won't boot. It's looking for a boot device. When I put in a Hiren boot 10.6 disk, the dual boot option is one of a number of alternatives, and it allows me to get into my pc. How can I get back to having the system work like it did before? So it boots to the dual boot option without Hiren.My SSD drive is the main drive for Windows 7 &XP. It has two partitions.
I have just given my Dad my old PC, to replace his ancient one from around 2000.It has a SATA hard drive with Windows 7 installed on it. The problem is he can't use his old printer with Windows 7. There is an available driver, but when I attempt to extract it, the message says there isn't enough storage space. This seems a bit crazy to be honest, as it;s not a very big hard drive (75GB total), but there is around 30GB free.Anyway, unless you guys have a solution to that problem I was going to take his old hard drive (80GB) and put XP on it and make a dual boot setup. Then he could use his printer in that at least. I was wondering though if I could simply pop that one into the new machine as it does currently have a recently installed copy of XP on it. I am aware that this may cause issues, but I wanted some good advice.
Also, this hard drive is an old style one (the one with the jumper) settings and I only have one connection on the motherboard for it. So I have had to connect the DVD drive and the hard drive on the same cable. I know that's not ideal, but it seems like there isn't another option. That won't cause problems with the dual boot setup will it?
4 hard drives 1 160 gigabyte at sata controller 0 position 0 1 64 gigabyte at 0 1 2 bluesy drives at 1 2 & 3 1 1tb drive at 1 4 1 2tb drive at 1 5
The 1 tb is a Debian system running ext4 The 2 tb is a data drive running ext4
The 64 gb is empty And the 160 is empty and where I intend to install windows However it seems that I can't it is not partitioned however when ever I say that it is to be partitioned through the windows install partitioner it again says that it's invalid and I can not continue?
My PC is set up for dual booting...first OS installed is Windows XP sp3 and the second is Windows 7 Ultimate x32. Both are installed on separate hard drives. I want to reformat the drive with Windows 7 on it and do a clean install of itctions on how to do this? For some reason I can't get the PC to boot up with the DVD disc instead of the hard drives, and I don't know much about the BIOS to mess around in there.
Just today I needed to reinstall XP on the same partition that it was on. Now my problem is that because of the reinstall, the bootloader that Windows 7 changed is now gone and I no longer have the option to select Win 7 during bootup.
Is there away to get the option back without having to re-install Windows 7 all over again?
I have Vista and W7 dual-booting. I was using iTunes on Vista, and now wish to use it in W7, using the same library. Has anyone achieved this? If so, how?
I have my hard drive partitioned to boot Windows 7 and Kubuntu 10.04. The default operating system is set to Kubuntu but I would like to change this to Windows 7.
I have just got my Win XPpro 32bit & Windows 7 64bit dual boot system working fine, but i have a problem with syncing mail between the 2 OS's, is it possible and how do i do it.
Well, I did a dual-boot system with Vista 32-bit and 7 64-bit. Now the problem is that, when I'm in Vista, the drive letter of Vista would be C: and 7 would be in B:.
But when I'm in 7, its partition would have the letter C: while Vista would have B:.
Is this normal? What would happen if I installed a program on the path C: in Windows 7?
I am dual booting Vista and Windows7 RC 7100. They are both on the same Hard Drive on different partitions. I have made the decision to stick with the new OS (Windows7) and give Vista the boot. So I want to get rid of the extra partition and revert to a single OS (Windows7).
I don't want to reformat the whole hard drive and completely re-install the windows7 operating system. I want to remove Vista from the dual boot menu and keep windows7. Then I want to format the Vista Partition. How can I do this and keep my present installation of Windows7 without having to reinstall Windows7?
I am at a bit of a loss here in regards to partitions, as I've never really done it, I want to configure a new system setup under the following circumstances:
SSD(1): (dual-boot OS drive) + Partition 1: Windows 7 + Partition 2: Windows Server 2012
SSD(2): (program / file drive) + Partition 1: one large single partition for application / program storage; e.g., Visual Studio 2012 and SharePoint Server 2013.
I need to have an instance of Windows Server to use SharePoint Server. At times I will want to run the server set-up to facilitate TFS and SharePoint with a very small team of developers, school related for example. And at other times I would like to boot into Windows 7 Ultimate so I can have a normal browsing experience and play games, etc. But of course I could also develop with VS11.X in Win 7 environment if needed.
My question, is what I'm proposing possible? I want to use Windows 7 normally most the times, but at others I will require Server 2012 to use SharePoint. Can I share the same program resources on the second SSD regardless what OS I boot into? What issues may rise if I tried running SharePoint (or just having SharePoint) while booted into Windows 7? Will I have to create two partitions on the 2nd SSD, a copy of apps for each OS due to system registry constraints.
I have sony vaio laptop and i was running windows vista on it. I did a partition and dual boot the system with ubuntu 10.4. Then i download easybcd tool to set windows vista as a default OS to boot with, but accidently in easybcd software i unistalled vista boot loader. now when i reboot the system ubuntu works fine but when i try to load vista its says NTLDR is missing Press Ctrl+Alt and Delete to restart. Then tried to boot from cdrom because i have a fresh copy of Windows 7. the system doesnt boot from cdrom. So now i am stuck with ubuntu on my system.
I have a system that dual boots with Windows 7 (64 bit) and Windows XP (32 bit); each OS is on its own hard drive. I want to reformat the Windows 7, deleting the OS in the process. What I'm wondering is where is the boot loader located? Is it on the Windows 7 drive (since it was installed after XP), and will I need to do anything special to have the system load Windows XP by default after the Windows 7 installation is gone? Will the system simply detect the old XP installation and load it without the bootloader?
I want to keep XP for compatibility reasons with some older hardware I still use often. I have XP installed on one hard drive and Windows 7 installed on another. When I installed Windows 7, I just went with the option for it to install a boot manager, and have been using that one ever since to dual boot my system. Nothing special, but it works.The current motherboard is an ASUS model, and has always had problems with the USB section (it took me quite a while to realize it was a motherboard problem, though). Then it began to develop problems reading the DVD drive several months after I installed it (back when it was only an XP system). Once again, not suspecting the motherboard, I replaced the DVD drive, thinking it had gone bad -- it hadn't, works fine in another system. And pretty soon thereafter the current drive began to work sporadically, and now doesn't work at all. Same as before.
This ASUS mb has a 3-year warranty, and it's not quite 2 years old. So, I should probably just suck it up and jump through the dozen or so hoops they toss in your path to get the mb repaired/replaced. Still, I'm guessing that if I'm successful, I may end up with a mb that is different enough from the one I have now where it's gonna break Windows 7 and XP.
I went through this when I originally replaced the motherboard, and ended up having to completely reinstall XP, reactivate it, and then d/l all the updates. I guess I'll be looking at having to do this now for both OSes, eh? If I have to reinstall both OSes, I'm thinking that I should install XP first, then Windows 7, mostly to preserve the dual-boot capabilty?
If I don't get satisfaction from ASUS, I'll probably just drop back 10 and punt, and go with a new mb. I'm gonna try to avoid this though because it's getting harder and harder to find mbs with PCI slots (I need three). I guess if I do this, it will probably amount to the same amount of work as if ASUS sends me a board that is substantially different from the old one.
I have a new Toshiba Qosmio X770 laptop with Dual 120 Gb SSD drives. From the factory it had Win 7 Home. I upgraded immediately to Win 7 Ultimate x64. I set up the VM to use XP (Have to use XP because current dev projects with work are stuck in old ages on XP for the time being). I can run the XP Mode in VM fine and even Visual Studios functions fine. There is a problem with the 3rd party drivers for the USB comm boards we are using, the USB drivers apparently cannot be shared across the VM environment for the particular ones we are using.
I already have windows 7 Ulitmate x86 but 1 day I came up with an idea of giving a try on x64 one by dual booting.. So I downloaded it legally from microsoft and I did every procedures required for the install. Shrunk my C drive and installed the OS on the unallocated free space on the drive and it went on perfectly. But the problem is the System Reserved partition showed up on the x86 OS. every time i open My Computer i can see the system reserved partition.
I could accidentally do something wrong with the partition if it remains unhidden so I want to hide it. I was thinking of changing the drive letter but I afraid that's going to give me boot problem. In disk management the System Reserved is labelled Z and marked as active. I tried to set my other partition as active that day but the pc cannot boot at all not even the boot manager showed up. However I managed to fix it using my recovery disc to access the cmd and reactivate the Z drive using diskpart.
I have an Acer Aspire one. It came with XP and I have it dual booting into Windows 7 which is working well which I installed from a USB Drive as this model doesnt have a CD Drive.
In the main boot screen it says "Earlier version of Windows" For XP and "Windows 7" for windows 7. All was working well until yesterday...
Now I can't boot into "Earlier version of Windows" i.e. XP. It gives me the C:\windows\system32\config\system is missing or corrupt message. I can boot into Windows 7 fine but all of my work stuff is on the XP platform (I know I can access the files from "7" but I need to get it operational again).
Any ideas? Can I do a repair from the USB Drive?..I've tried a couple of things to boot from the USB Drive but to no avail. And I can't find the BOOT.INI file from XP (I think it gets moved to Windows 7's hidden boot partition when I installed it. I cant seem to access that partition either).
I have a new computer with an i7 and 12GB system ram using Win 7 64 bit and had a question about how to utilize more than 3Gb system ram for games.How can I make a game in 64 bit o/s use more system ram say 8GB instead of 3GB for better performance? The game is Arma 2 Combined Operations.
My system dual boots to either Windows 7 or Vista Ultimate, or, at least it is supposed to. Something happened and now the system just boots to Winodows 7 without giving me the choice to boot to either. When I use F6 I find that only Windows 7 is listed in the Operating Systems box.
I need to flash some roms on a graphics card and a disk controller card, but both require the use of a 'boot floppy' (i'm adding that in quotes as this is totally alien to me!
I suppose this means some sort of ancient dos thing!
I've really tried against all odds to eliminate floppy and serial / PS2 devices from my life, and now I've achieved this, and my loft is far too dusty to be crawling around in trying to find such things again!
Could I create this dinosaur relic on a USB stick, and if so, how does one go about it?
I tried making my usb stick bootable as I did in the wonderful thread on this forum to install RC1 and it worked a dream, but i'm guessing this isn't the same thing is it .
i have a new work laptop with xp sp3 on it. I want to install w7 64 bit as a dual boot, but only have 1 physical drive. i cannot remove my current installation as it is pre-build from work, but can partition the drive etc. However on trying to install w7 64 bit I get a message saying cannot install windows 7 on efi drive with mbr, not gpt. Can I do what I want without screwing up my xp installation?
I recently upgraded my CPU, PSU, Motherboard and Ram. I kept my original dvd drive and hard drive. I have an issue when trying to start windows, it shows a blue screen for half a second and then restarts again. I have tried to use the repair tool but it doesn't work.
The person in this link had the same problem : [URL]
and someone mentioned that you have to do a clean install as my hard drive was so old and the motherboard is so new. What I am going to do is use an external hard drive I have and make it bootable so that I can place windows files on there as I do not have the windows disk.
My question is, once I have booted it from the external drive can I install the windows from the external hard drive onto my old hard drive so that I can unplug the external one after I have finished?
in my PC there are some drives with RAID0 arrays and from little time I have bought a SSD for Operative System (Windows 7).in your opinion (on the BIOS) is it better making the Boot with SSD or with another drive with RAID0?
I decided to use DigitalRiver to download my copy of Windows 7 and I will NEVER use them again. They have no phone or tech support; the only way to contact them is by email, in which a response can take many days.
It took me over 10 hours to download their download manager. While the DM seems to work OK, I keep getting the same error message near/at the end of the unpacking:
"We are unable to create or save new files in the folder in which this application was downloaded. Please check the folder properties to make sure that you have security permission on the folder to write files and that the folder is not read-only"
So while I wait for some intelligent response from them, I'm trying to create a bootable DVD but I'm not having any luck. I've tried using BurnAware and UltraISO yet every time I reboot, the DVD never boots...any ideas on exact steps to take?
