Get The ACHI Port3 Device Error
Mar 22, 2012i get the ACHI Port3 Device Error...Shld i get rid of it or is their a Way( i wish their was i cant even afford another computer personally issues
View 5 Replies
ADVERTISEMENT
Want To Switch To ACHI
May 31, 2010I have my dad's computer already setup with Windows 7. For some odd reason being that there is only one drive in the computer. the computer's bios is set to RAID. I know you need at least two drives to perform any RAID functions. When I tried to switch over the SATA drives in the BIOS from RAID to ACHI, windows failed to start. Is there some proceedure first that I need to do before I switch them? Like a driver or does the hard drives have to be switched on a clean install of windows?
View 9 Replies View RelatedReinstalling Windows 7 As ACHI Mode
Oct 4, 2012I had a friend help install windows, back then I was clueless about the whole deal with achi and ide. A while later, I had to switch hard drives just to run some tests, and the computer wouldnt but, even after putting the original back in.
Turns out BIOS had set itself to ACHI, not allowing windows to boot. Switching it to IDE made it work.
Now I bought an SSD, and its not quite detecting. Im also hearing ACHI is much faster than IDE, so I want to just spend time and switch over.
How would I go about reinstalling windows as ACHI? I have an installation disk and everything. I've already started backing up files to leave the boot disk empty and ready to roll.
ACHI Driver Issue W7x64
Oct 25, 2009I'm making a post as a W7x64 install is driving me nuts. During Windows 7 setup, at the F6 prompt, I've loaded the drivers for the Southbridge to enable SATA hotswapping and NCQ'ability.
When I set the BIOS to ACHI mode the Windows 7 installation fails to complete, during the first reboot within setup Windows 7 will report a hardware fault and refuses to reboot.
When I set the BIOS to IDE mode the installation goes fine, but there's no sign of hotswap or NCQ onboard.
All my SATA drives are in SATA-II mode (Barracudas, 1x 80Gb boot, 2x 1Tb archivage, 1x 500Gb misc') so this isn't the cause, and they're all connected to the orange/yellow main bank of six SATA ports (there is nothing attached to the purple Gigabyte chipped twin headers).
I've already swapped out all the SATA cables and chkdsk'd the drives, and verified the integrity of the Windows 7 DVD.
My board had the original BIOS when I checked, so I upgraded to version F6. Alas nothing has changed. Other components are a Palit HD4850 Sonic graphics card, 8Gb OCZ 1,333Mhz RAM, plus a modest Intel Q9300 2.5Ghz CPU.
If anyone has experience of loading the Southbridge ICH10 drivers under Windows 7 and can spare me an explanation I'd be very grateful.
Windows 7 Hangs At Startup In ACHI Mode?
Sep 14, 2011I've recently upgraded my computer with an ASUS P6P67 Pro, Intel i5 2500K, Corsair Vengeance 8GB and Corsair TX650 The operating system is Windows 7 Ultimate 64-bit.The installation of hardware went fine, I used my WD Raptor 64GB as system drive and connected my 2 other drives.Maxtor 250GB and Samsung Spinpoint 750GB. (they will be replaced eventually)The installation of Windows 7 also went fine, no problems at all. When it was installed I could see all harddrives and I could browse them. But after I installed the drivers from the DVD from Asus and restarted the computer it hangs at the Windows logo waving. It just keeps waving for hours.When I disconnect the Maxtor and Samsung drive, it boot up correctly. I've only tried to connect them to the Intel SATA Controller. I tried to switch between the connectors but it didn't boot up.When the drives where disconnected I could resume the configuration of Win 7 and I ran Windows Update to install SP1 but still the same problem when i tried too connect the drives?I reinstalled 2-3 more times, but no. Then I changed in BIOS from ACHI to IDE on the Intel SATA Controller and reinstalled again and now it works?I updated everything in Windows and restarted it several times and it boot up every time. But I wish to use ACHI, since I'm planning to run RAID 0 I've used the latest chipset drivers from Intel and IRST as well.I need to clarify that the problem begins after the installation of chipset drivers.
View 8 Replies View RelatedInstall Windows 7 In ACHI Or IDE Sata Mode For SSD?
Jul 14, 2010Well, I've done a lot of research (googling) on whether or not to install Windows 7 on my solid state drive in AHCI or IDE sata mode. I wanted to confirm it with you guys to make sure I got this straight before I go ahead and install Windows 7.
If I install windows 7 on my solid state drive in sata mode ahci then later I can go to IDE if I wanted to by just switching it in bios. But if I install windows 7 under IDE mode then ill have to do a registry value change to make windows 7 work in ahci mode.
Everyone seems to have a different opinion on whether or not ahci mode is faster or worth it over IDE mode for windows 7 on a SSD. I'm not all that interested in hot swapping so thats not a interesting feature for me. I'm looking for reliability as a top priority.
Change ACHI Controller That Appears To Be In IDE Emulation Mode?
Mar 18, 2011I installed Windows 7 on my SOLID 2 Series SSD with it only plugged in during install. I latter added a 1tb Spinpoint F3 hard drive, and velociraptor for programsDespite the bios is in ACHI mode and it says ACHI controller installed I get these two things popping up.Is this normal? Can I change it to ACHI from installing drivers[CODE]
View 3 Replies View Related'Error While Opening Sound Device. Check The Input Device Settings And The Project Template'
Mar 1, 2010I have an emu 1820m soundcard installed in my computer. It seems to be functioning perfectly. I can play dvd'd, cd's, iTunes, etc and the sound plays through my speakers without a problem. I want to record some sounds from a dvd but i cant get anything to record. Recording device is set to Wave EMU DSP as the default device. Im using Audacity to record and have set the recording preference device to be Wave (E-MU _-DSP). When I hit record I get an error 'Error while opening sound device. Please check the input device settings and the project template'And I cant record anything.In the built in Windows sound recorder, when I hit record, I get this error 'An audio recording device cannot be found' Everything seems to be functioning perfectly, yet i just cant record anything.
View 8 Replies View RelatedDVD-ram I/O DEVICE Error
Mar 9, 2009I recently did a clean install of Windows 7 x64, and my I cannot install from my DVD drive. When i attempt to open the drive in command prompt it gives me an I/O device error message. I can open media disks with no problem, and the drive appears in both device manager, and windows explorer. I've attempted to find the firmware for the driver (mat****a UJ-840s) but I have not been successful. One more note I went from a 32 bit XP to the 64 bit windows 7
View 5 Replies View RelatedNo Such Device Error Message?
Mar 9, 2012I installed Ubuntu side by side to my win 7. On the install it would only install to an external drive I have. After the install completed an I restarted my computer and I got an error message=" error: no such devive: 868152e-2012-469b-b469-ebc2c953dfb4.grub resue>"I restarted my computer a few times and kept getting the same message.I decided to restore my computer back to factory defaults. After doing this I restarted my computer but kept getting the same message.
View 2 Replies View RelatedUsb Device Not Recognized Error
Jun 26, 2011I have a laser projector, and i control it with my windows seven notebook by usb.
Problem is, sometimes by a static shock of other devices or by other causes i do not know of, the notebook suddenly refuses to work with the usb drive anymore and the projector freezes.
but here is the part i want to solve. after replugging the usb drive windows says that the usb device is not regonised.... after plugging out and waiting 2 minutes and then replug makes it work again...if i do it sooner then usally it still shits about the device not being regonised.
'This Device Can Run Faster' Error
Aug 17, 2011Recently, I've started getting an error which says: "Your USB Composite Device can perform faster if it is plugged into a hi-speed port" "The hubs shown in bold type have free ports that can support the HI-SPEED USB device"
It then lists two bolded options for a hi-speed ports: A USB Root Hub with 6 ports, and another with 4. This error occurs on both my Windows 7 equipped Dell XPS15 (which has 2 USB ports) and an older Dell laptop which runs Vista (3 USB ports)
This is shown after my external drive (a seagate model) disconnects from my computer, which usually ends poorly for me, since I typically run Photoshop off my drive.
I'm wondering if these errors are caused by a new USB splitter I bought. It has 4 ports, but the model year and quality of the thing are dubious at best; my webcam and wireless mouse are also typically attached to it, and the webcam disconnects at the same time as the external drive. The mouse still works though, so that's pretty mysterious.
An Error Was Detected On Device
Nov 30, 2009Every time im exploring my fone's memory card,or any other kind of storage like usb memory sticks, the window explorer closes down, and i have to open it agin,locate the folder i was on,but then it will happen again.
If i check Event viewer (System bit)it generates the following event: An error was detected on device DeviceHarddisk2DR2 during a paging operation.
Is my hard drive working ok?+ i noticed that my computer works slow,when im on windows explorer,going to my music,etc...
any help?
Unknown Usb Device Error
Nov 16, 2011I just bought a amd phenom ii x4 955 and a asus m4a88tm le motherboard . After that i formated my hdd and installed win 7 ultimate and amd motherboard drivers. Now when i connect a usb device it shows Unknown usb device (except my mouse and keyboard).
View 6 Replies View RelatedError In Bluetooth Device?
Jun 5, 2012my bluetooth is not working .. my dell model is inspiron n5110..
View 1 Replies View RelatedNo Bootable Device Error?
Jun 30, 2012I have an Acer Aspire On 10inch Notebook that runs on Windows 7 Premium Edition (32bit). I'd been having some troubles with its speed for a day or so and since I'd neglected to do a Windows update. So, I restarted it and hoped that once it installed those updates everything would be fine. My first warning sign was the time that it took to turn off - probably 15 minutes was spent with the screen continuously saying "Shutting Down" and I took this to mean that it was probably a series of updates that I had missed. So, I left it to sit and came back to check on it afterwards.When it finally finished, a black screen took over and sat there for quite some time. Eventually I grew frustrated and restarted the computer, and saw the 'Acer' screen come up, and then the computer screen went black again and a command line started, where I received this message[CODE]
View 3 Replies View RelatedUSB Device Not Recognized Error
Jan 11, 2013USB Device not Recognized::error while connecting my external hard disk,previously it was working fine
View 2 Replies View RelatedBoot Device Error
Jun 28, 2009It all started with my pc restarting(it was a power failure) to show boot device failure, insert system disk, i tried everything, from unplugging usb devices to re inserting sata cables but to no avail, now when i try to reinstall windows the setup recognizes all my partitions but refuses to install into any of them, ubuntu only recognizes one of my hard disk and partition( i have 1 big 500 g hdd as 1 part, and 2 250 g hdds in raid 0).
I tried booting from my bart pe created windows live cds but they dont detect any partitions what so ever, windows 7 dvd's repair utility can access my file structure when i browse for drivers, but it wont repair the problem, nor will it install.
Unable To Boot Device Error?
Jan 30, 2012My friend's desktop PC had this issue, it runs Win 7, is an HP and is just one year old. It either gives the "Unable to boot device error", or asks for the Windows CD that he doesn't have (bought it at a department store, it came with Win7 original installation but no CD). It doesn't open Windows. It still recognizes it as a hard drive in the BIOS screen, the startup order was never altered and should be Hard Drive then CD/DVD. Searching for a quick solution he found suggestions to try and change from AHCI to IDE in the BIOS and at last it got to Windows startup. Win7 in safe mode prompts him a repair mode that's going on for two hours.I downloaded the hard drive maker's tools for diagnostics (they're burnable on a cd) and will try them if this windows repair mode keeps going on indefinitely.
View 1 Replies View RelatedCannot Get Rid Of (USB Device Not Recognized) Error Message
Jan 31, 2012Whenever I use one of my USB ports, afterwards I get an error that lasts all the time that says USB device not recognized. I have gotten rid of it but then when I go back and use it again, that error pops up. The usb ports work, I use it to download pictures and other things, but I cannot get the error gone. Someone suggested I unplug the internet completely for a few minutes and it would reset itself, but that didn't work. I put the media card usb back into the port and went to where it says it is safe to remove hardware and then took it out, but that didn't work either.
View 9 Replies View RelatedError Code 43 In Device Manager On The USB Hub?
Sep 30, 2009I got Windows 7 ultimate 64bit from microsoft technet. Everything is working fine except for the USB ports in the back of my computer, when i go to device manager I get the error: Code 43Windows has stopped this device because it has reported problems. (Code 43), I have tried the drivers for my motherboard from the Gigabyte site, the ones for Vista 64bit, but no luck,
View 9 Replies View RelatedNotebook - No Bootable Device Error
Oct 4, 2011i have an acer aspire one notebook and one day it was working and the day after when i turned it on it goes to the normal acer loading sign then the screen goes black and makes a beeping noise for about 10 seconds then this error comes up
Intel UNDI, PXE-2.1 (build 082) Cpoyright (C) 1997-2000 Intel Corporation For Atheros PCIE Ethernet Controller v2.0.0.9(05/08/09)
Check cable connection! PXE-M0F: Exiting Intel PXE ROM. No bootable device -- insert boot disk and press any key When i click enter this message just appears again.
Gets An Error When Unplugged A Removable Device
Nov 19, 2011"Windows has encountered a problem communicating with a device connected to your pc.This error can be caused by unplagging a removable storage device...,or by faulty hardware such as a hard drive or CD-ROM.Make sure any removable storage is properly connected and then restart your pc.
View 1 Replies View RelatedCD / DVD Device Driver Missing Error
May 17, 2009I was trying to install Widows 7RC on Sony VAIO CS-14G laptop. I inserted the disc, clicked on Install and got the following error:
[code]....
Code 31 Error In Device Manager
Jun 27, 2011Somehow I messed up install of a PCI wireless adapter. Device Manager says 'device not working properly because it can't load drivers: code 31.
I've pulled the adapter card out. ran the computer awhile without it, reinstalled it and same problem.
Then I did the registry thing about upper and lower filter deletion but the filters are not listed. Yeah I went to the right place in the registry to look.
AHCI Port0 Device Error
Aug 8, 2011When i turn my laptop on it comes up with: AHCI port0 device error. At the moment i am trying to re install windows 7 but it (after changing the BIOS) it gets to a screen where it states that it is starting?
View 2 Replies View RelatedCD / DVD Device Keeps Disappearing- Error Code 32
Jan 4, 2012Windows 7 ultimate 64, my Atapi iHAS124 B ata CD/DVD device keeps "disappearing" try running the Microsoft "fis it now"...and get A driver service for this device has been disabled. An alternate driver may be providing this functionality. Code 32 Tried uninstalling the device and installing new drivewr....same result. This is the 2nd time it has happened...last time I ended up having to rebuild the system from scratch.
View 7 Replies View RelatedDirectx Device Creation Error?
Mar 7, 2012Directx device creation error?
View 2 Replies View RelatedGetting A Device Manager Restricted Error?
Mar 8, 2012my computer is upgraded from Vista to 7. I am getting a device manager restricted error.
View 1 Replies View RelatedRequest Could Not Be Performed Because Of An I/o Device Error?
Oct 4, 2012i was watching a movie on my laptop, all of sudden my external hard drive stop working. i can not see it.
View 1 Replies View RelatedD3d Device Error Code 2005530516
Dec 17, 2012D3d device error code 2005530516?how to solve this error?
View 1 Replies View Related