Reinstalling Windows 7 As ACHI Mode
Oct 4, 2012
I had a friend help install windows, back then I was clueless about the whole deal with achi and ide. A while later, I had to switch hard drives just to run some tests, and the computer wouldnt but, even after putting the original back in.
Turns out BIOS had set itself to ACHI, not allowing windows to boot. Switching it to IDE made it work.
Now I bought an SSD, and its not quite detecting. Im also hearing ACHI is much faster than IDE, so I want to just spend time and switch over.
How would I go about reinstalling windows as ACHI? I have an installation disk and everything. I've already started backing up files to leave the boot disk empty and ready to roll.
View 3 Replies
ADVERTISEMENT
Sep 14, 2011
I've recently upgraded my computer with an ASUS P6P67 Pro, Intel i5 2500K, Corsair Vengeance 8GB and Corsair TX650 The operating system is Windows 7 Ultimate 64-bit.The installation of hardware went fine, I used my WD Raptor 64GB as system drive and connected my 2 other drives.Maxtor 250GB and Samsung Spinpoint 750GB. (they will be replaced eventually)The installation of Windows 7 also went fine, no problems at all. When it was installed I could see all harddrives and I could browse them. But after I installed the drivers from the DVD from Asus and restarted the computer it hangs at the Windows logo waving. It just keeps waving for hours.When I disconnect the Maxtor and Samsung drive, it boot up correctly. I've only tried to connect them to the Intel SATA Controller. I tried to switch between the connectors but it didn't boot up.When the drives where disconnected I could resume the configuration of Win 7 and I ran Windows Update to install SP1 but still the same problem when i tried too connect the drives?I reinstalled 2-3 more times, but no. Then I changed in BIOS from ACHI to IDE on the Intel SATA Controller and reinstalled again and now it works?I updated everything in Windows and restarted it several times and it boot up every time. But I wish to use ACHI, since I'm planning to run RAID 0 I've used the latest chipset drivers from Intel and IRST as well.I need to clarify that the problem begins after the installation of chipset drivers.
View 8 Replies
View Related
Jul 14, 2010
Well, I've done a lot of research (googling) on whether or not to install Windows 7 on my solid state drive in AHCI or IDE sata mode. I wanted to confirm it with you guys to make sure I got this straight before I go ahead and install Windows 7.
If I install windows 7 on my solid state drive in sata mode ahci then later I can go to IDE if I wanted to by just switching it in bios. But if I install windows 7 under IDE mode then ill have to do a registry value change to make windows 7 work in ahci mode.
Everyone seems to have a different opinion on whether or not ahci mode is faster or worth it over IDE mode for windows 7 on a SSD. I'm not all that interested in hot swapping so thats not a interesting feature for me. I'm looking for reliability as a top priority.
View 7 Replies
View Related
Mar 18, 2011
I installed Windows 7 on my SOLID 2 Series SSD with it only plugged in during install. I latter added a 1tb Spinpoint F3 hard drive, and velociraptor for programsDespite the bios is in ACHI mode and it says ACHI controller installed I get these two things popping up.Is this normal? Can I change it to ACHI from installing drivers[CODE]
View 3 Replies
View Related
Apr 12, 2012
windows xp mode not working properly. When reinstalling it says "windows xp mode already installed". I cant install the virtual pc associated with XP Mode.
View 1 Replies
View Related
Sep 10, 2011
I was having problems getting virtual xp mode to boot on my windows 7 computer. I deleted windows xp mode and reinstalled it. I was then able to open xp mode but when I opened Acess 2003 and looked for my database for my business It seemed to have disappeared. Did searches in xp mode, on windows 7 in all drives.
View 1 Replies
View Related
May 31, 2010
I have my dad's computer already setup with Windows 7. For some odd reason being that there is only one drive in the computer. the computer's bios is set to RAID. I know you need at least two drives to perform any RAID functions. When I tried to switch over the SATA drives in the BIOS from RAID to ACHI, windows failed to start. Is there some proceedure first that I need to do before I switch them? Like a driver or does the hard drives have to be switched on a clean install of windows?
View 9 Replies
View Related
Mar 22, 2012
i get the ACHI Port3 Device Error...Shld i get rid of it or is their a Way( i wish their was i cant even afford another computer personally issues
View 5 Replies
View Related
Oct 25, 2009
I'm making a post as a W7x64 install is driving me nuts. During Windows 7 setup, at the F6 prompt, I've loaded the drivers for the Southbridge to enable SATA hotswapping and NCQ'ability.
When I set the BIOS to ACHI mode the Windows 7 installation fails to complete, during the first reboot within setup Windows 7 will report a hardware fault and refuses to reboot.
When I set the BIOS to IDE mode the installation goes fine, but there's no sign of hotswap or NCQ onboard.
All my SATA drives are in SATA-II mode (Barracudas, 1x 80Gb boot, 2x 1Tb archivage, 1x 500Gb misc') so this isn't the cause, and they're all connected to the orange/yellow main bank of six SATA ports (there is nothing attached to the purple Gigabyte chipped twin headers).
I've already swapped out all the SATA cables and chkdsk'd the drives, and verified the integrity of the Windows 7 DVD.
My board had the original BIOS when I checked, so I upgraded to version F6. Alas nothing has changed. Other components are a Palit HD4850 Sonic graphics card, 8Gb OCZ 1,333Mhz RAM, plus a modest Intel Q9300 2.5Ghz CPU.
If anyone has experience of loading the Southbridge ICH10 drivers under Windows 7 and can spare me an explanation I'd be very grateful.
View 9 Replies
View Related
Nov 25, 2011
I bought a brand new Samsung QX411 two months ago. It's a great computer. Problem is, it got hit with a nasty virus that was pretty much completely debilitating, so I took it in to Best Buy (mistake), and they told me the best thing would be just reinstall Windows 7, and everything would be great. Well, I did, and now I am stuck. I reinstalled, but I did not realize that literally nothing would be in place. I am not completely naive: I did save all of my important files, folders, music, etc. So it's not that I have lost my data and am now crying "woe is me." Instead, I have basically a blank Windows 7 and nothing is there. I can't connect to the internet, because it is telling me that I don't have the necessary hardware (I know I do, but still). A basic summary would be this: I have no idea what to do after properly installing Windows 7. I want to get it as close back to normal as I can, but I don't know how to start.
View 5 Replies
View Related
Jul 13, 2012
I recently built a new computer system that contains my old HDD, which I transferred from my previous PC. The old copy of Windows 7 that was already installed didn't work in the new PC, as expected. Instead, I have a new copy of Windows 7 available that I need to get on the HDD. But I also need to deal with the old Windows copy. I've already transferred all of my personal files from the old copy onto a portable HDD for safe keeping. What I plan on doing is reinstalling the new copy of Windows 7 onto the PC's HDD to be used in the new computer. I was able to acquire the new Windows 7 version for a really cheap price from my college.
So now I either have to format my HDD so that the new Windows 7 can work properly while keeping the old/useless version out of the way, or wipe the old Windows 7 from the HDD completely. Should I keep the old Windows 7 on the HDD and just never use it, or would that conflict too much with the partition used by the new version? If they do conflict, how should I go about removing the old Windows 7 partition? dealing with the HDD and OS seems to be one of the most annoying parts of a PC.
View 3 Replies
View Related
May 7, 2011
I have bought a Lenovo Ideapad about 6 month ago with Windows 7 Home Premium.I now want to Re-Install Windows and delete my whole data. In Short, I want it to be Completely Clean.I Dont have My Windows CD to do That, But I have a Key Below My laptop and its Genuine.
View 3 Replies
View Related
Dec 7, 2010
I mistakenly purchased a 32 bit version of windows 7 pro which was on OEM. Now I am going to purchase the 64 bit version OEM software again and format my hard drive and reinstall the 64 bit OS on my PC.
My question is now that I will be using the 64 Bit version, can I re-use my 32 bit OEM on a completely different PC as it will no longer be installed on my PC?
If so do I have to uninstall it first or will a simple wipe off the hard drive deactivate the 32 bit key? Also is there a cheaper option to purchasing the OEM software again, such as upgrading from 32bit to 64bit?
View 4 Replies
View Related
Dec 11, 2010
I've recently purchased an SSD and would like to utilize it as a boot drive. I am happy with my configuration and would like just to install Windows 7 on the SSD and use it to boot -- with all other hardware and drives remaining without change.
View 6 Replies
View Related
Jan 5, 2013
So I've been using my new laptop recently and discovered its hybrid hard drive contains an SSD. And boots up windows in seconds. This has caused me to want to buy an SSD for my desktop (my real gaming machine). The trouble lies within reinstalling windows and backing up.My desktop currently has two hard drives. Both 1tb each, one is full. And the other is barely used up. If I were to buy an SSD for my desktop. Would it be possible to reinstall windows (OEM) onto my new SSD? How would I do this? Also I've never backed up before (terrible I know and I want to start now!). However my family does own a 1tb external HDD. How much of my 1.2tb of data could I backup, and how would I do it? I've got loads of games and whatnot installed I don't want to lose.
View 9 Replies
View Related
Nov 22, 2011
I'm currently running windows 7 64 bit on my current system. I am just after buying a new pc and want to install my OS on my new SSD. I'm going to keep the old raptor HDD for my new system also (the raptor HDD currently has the OS on it)
1. Can I install windows to my SSD using the same product key yes?
2. How can I/whats the best way to completely remove the OS from the raptor HDD and just use it as a storage device..I want to use the 120GB SSD for the OS & some of my games - (Origin & Steam)
View 5 Replies
View Related
Dec 30, 2012
I just installed and activated OEM Win 7 on an HDD. Changed my mind and want to purchase an SSD, place Win on that, and use my HDD for everything else. Will I still be able to install Win or am I too late because I activated it?
View 4 Replies
View Related
Jan 31, 2013
I'm not sure this is the right forum for this question, but then again: lots of people seem to have comparable problems, so here goes:As my 3-year old netbook was getting very slow, I decided to get rid of all the junk at once by completely reinstalling the OS (Win7 starter). Now, there is a very easy way to this with the Recovery Manager (as described in the support papers on the HP site), but that didn't work for me. This may wll be due to a faulty HD; I've no way of testing it as my C: drive is now reformatted. So what next?I was not completely unprepared; earlier I made:- a USB-stick with the 'HP USB Recovery Flash Disk Utility' (HP45774). The stick does contain, I think, all or almost all of the contents of the recovery partition. (NB: you need a 16Gb stick and this is a trick you can do only once.
- a recovery CD on an external CD drive, although without a 'disk-image' as by then the system had grown much too bloated already. (should have done that straight away after I'd bought it, although I'm a bit at a loss as to what storage medium would be used).These two means should surely be enough to restore the thing to factory settings? However:- The memory stick should be bootable, but isn't.- Booting from CD works, but the Recovery Manager can't seem to access the diskimage on the usb-stick. (Although, when I call up a command prompt, one of the other options, it is readily available.)So I don't really know what to do now. I'm thinking of two options:1. In one forum thread it was said that the stick thus made 'often' or even 'usually' isn't bootable, as it should be. The advice was to make it bootable, using EasyBCD. That's easier said then done, I found; no luck so far.
The stick does contain a boot directory, bootmgr etc.; it clearly is supposed to be bootable.)2. Following the advice in other threads, I downloaded the whole 1.7Gb WAIK, just to get hold of imagex.exe, which i then put on the memory stick. As the bootable 'recovery CD' does provide a command prompt, I could, supposedly, 'apply' the image base.wim, which is also on the stick, to 'drive D:' (under these circumstances, that's the main partition). But as there's lots of other stuff on the stick (like FactoryUpdates), I'm afraid it will be a lot of hassle installing computer-specific drivers and stuff.
View 5 Replies
View Related
Feb 26, 2011
I want to buy a new laptop. The problem is that new laptops come with a tonne of crap on them and I want a clean install of Win7.What would I need to get this clean install?Would I need to *cough* acquire an OEM edition of Win7?
View 5 Replies
View Related
Jul 21, 2011
I installed Windows 7 on one of my computers. I have another computer running Vista. Can I uninstall Windows 7 on my first computer and then reinstall Windows 7 on my other computer?
View 6 Replies
View Related
Jul 21, 2012
I reinstalled Windows. When it was done, the internet disappeared! It says "Not connected - No connections are available". I try to troubleshoot it and it says to install a network adapter driver. My router is Linksys WRT54GS and my modem is ubee.
View 3 Replies
View Related
Sep 14, 2011
I had multiple BSOD's on my laptop, i had to reinistall windows 7 because it could not boot up. After reinstalling and adding all drivers I got another blue screen.Please find attached the dmp file.
View 2 Replies
View Related
Oct 14, 2012
I decided it was time to perform a clean installation. I just got my computer last year and I've never done it before. I have 2 hard drives, each 1 TB. My primary hard drive is partitioned. The first 882 GB is the Local Disk. It has everything on it, the OS, programs, data, etc. The other 48.8 GB has the Windows 8 pre-release installed on it. My secondary hard drive is used for backup. I use the default Windows backup program. I'm currently performing a backup and I plan on creating a system image after that. Once those finish, I'm going to partition my primary hard drive again for the new installation. How much space do I need to give Windows 7 on a partition?
I was also wondering what to do after reinstalling Windows. Do I restore from the system image? I thought reinstalling Windows then restoring would defeat the purpose, wouldn't it? Also, what do the backups and system images cover? Should I just manually copy my programs and data to the internal backup hard drive? I just that that moving programs from where they installed then moving them back might mess some things up. I read somewhere that it would be smart to reinstall all programs. I wouldn't mind doing that, but there's one that concerns me. I'm a PC gamer and I use Steam. My Steam folder is almost 200 GB, please tell me I wouldn't have to download all my my games again...
View 3 Replies
View Related
Jul 24, 2012
i reinstalled windows 7 64bit a few weeks and since then ive been having startup problems. BSOD, restart during welcome screen, freeze on starting windows screen etc.need to know if its a simple fix or should windows be reinstalled or is it a hardware issue?
View 9 Replies
View Related
Apr 17, 2011
Windows 7 Home Premium X64 keeps re-installing the same existing USB drivers every time I plug in an USB device. This means every time I plug in my Wireless mouse, my printer, scanner, external hard drive... and so on I have to wait minutes before I can start using the device. Also, it does not just re-install the drivers from the hard disk, it does a lengthy check via windows update before it installs anything.
View 7 Replies
View Related
Dec 28, 2010
Used RT Seven Lite to slim down windows, but may have done a little too much in terms of removing Windows services (RasMan, etc.). Is there a way to reinstall the Windows components?I did try to manually create the services using sc create and trying to duplicate the service from another box, but so far it hasn't worked out that well
View 2 Replies
View Related
Aug 20, 2010
I am running Vista basic and Windows 7 ultimate on my pc and i was just wonder how can i reinstall Windows 7 while keeping vista and not changing anything on my C: drive ( which vista is in ) while just getting rid of Windows 7 and putting a new Windows 7 over that same hard drive ( hard drive D: ) . Is there any way of doing this and without causing any problems to vista, my pc and not having conflict's ?If so can you please tell me how to do it step by step?
View 9 Replies
View Related
Dec 8, 2011
I got windows 7 pro 64-bit though my school for only $30. It said it was only an upgrade. I also purchased the backup disc.BUT I downloaded the .ISO, wiped my drive, installed it, and it activated just fine, no errors.Now I just reinstalled it on a different hard drive, and its giving me the error that it is an upgrade only. This is using the same product key that worked before. I did this on another friend's new build and it gave the same error. I talked to a representative that said I should not have been able to install in the first place.I tried calling to activate, but when it gets to the product key, it will not recognize the numbers or letters when I try to type or say the key.I used the number 1-866-234-6020. I am getting nowhere on the phone.Can I get this product key activated for a full version anywhere? Any specific numbers I have to call?I have a disc of XP retail version lying around. Can I install that and upgrade using my backup disc
View 4 Replies
View Related
Apr 14, 2012
Just reinstalled Windows 7, walked away from the PC during the re-installation and it appears that a second partition was created in stead of overwriting the old partition. How can I start up the PC and delete the old OS? Or should I just re-install Windows 7 again and be at the PC when it goes through the steps?
View 7 Replies
View Related
Nov 4, 2012
Recently I decided to reinstall windows 7 without wiping my hard drive, but I ran into a problem. Everything was going smoothly until it reached the transferring data and settings. It went up to 72% and hasn't changed for an hour. If I try and close it down it simply says that it can leave the PC in an unstable state.Here is an image of what I'm seeing: and the number hasn't changed, and it is always changing from please wait to Transferring files imgur: the simple image sharer
Specs:
Windows 7 home Premium 64bit
6570 (amd radeon)
I5 2400
8gb of RAM
600W power supply (for future upgrades)
View 1 Replies
View Related
Nov 8, 2012
I'm Just the other day when i cut on my computer it wouldnt boot so i tried to restore it to a earlier time but it wouldnt work so i tried to restore to factory setting and it wouldnt do that either now i get a message telling me to restart installation cause windows couldnt be completed can someone please help. I have a ACER ASPIRE computer which windows was pre-installed and i have no disc. The disc i created dont work i put it n anotha computer and it said it was blank.
View 1 Replies
View Related