i recently built my computer and it has four hard drives, a new SSD, and three HDDs all taken out from my old computers. when i open my start menu and type something in only the results from the SSD will come up, how do i fix this, also all my old HDDs still have their operating system on the i never bothered working out how get rid of them.
View 3 Replies
Is it possible to do a full search for a document through my entire computer system including both external drives?
If so where do I start from.I tried by going to Computer from the Start menu then selecting the C: drive but was wondering if that done a full search of the other drives.
i can't see the hard drives in my computer
View 5 Replies View RelatedI just bought a new computer with Windows 7 Professional 64 bit . I added 2 hard drives from my old computer to the new one. The old computer was Windows XP 32 bit with a Raid 1 configuration. I just want the added hard drives as storage and non raid. The installation went smoothly but the new computer recognizes the 2 added hard drives as one drive. Also when I boot up, the boot screen from the old computer shows briefly with the intel raid 1 info.
View 5 Replies View RelatedI recently completed my first build within the last two weeks. After tinkering with everything for a while I decided to pull my HDD out of my old Dell and use that as a backup.
I then got to thinking about how it might be useful to install Windows on each hard drive and use whichever one I want for whatever I want to do with the computer. IE: One HDD will be only for games and the other HDD will be for everything else I want to do. I've done a few searches and found conflicting results. To add to this problem I returned my Gygabyte MOBO for a different model. I know I will have to reformat my current HDD that Windows is installed on. So here is the twist.
When I get the new MOBO hooked up I want to use my old Dell HDD as my primary HDD because it is bigger. Since Microsoft thinks Windows is installed on the other HDD and different MOBO what will happen with I install it on a new HDD and new MOBO? It would be essentially the same as installing it on a different computer which is obviously not something Microsoft wants happening. How is this done?
Now, given that I get that to work can I then disconnect my primary HDD and plug in my second HDD, boot from disc and install all over again. I have no problem going back and forth disconnecting and connecting which HDD I want to use when i boot up if I cannot have them both hooked up to the MOBO, but I assume I can and will just choose which to boot from in BIOS. I do not plan on moving data between the two drives as I will use an external HDD for any data backup that I might need.
I can not select my boot up drive anymore from my two hard drives, two OS pc. Both drives are SATA drive, but one of them appears as IDE in Bios. What is going on here?
View 1 Replies View RelatedRecently my computer's hard drives started clicking, both of them. I wasn't able to copy off my files or boot up as it would constantly freeze. So in order to save my data I bought a sata to usb cable to connect to my laptop to copy off the data. When I connected it I was able to save all my data and the hard drive didn't freeze one bit...a friend of mine suggested that it wasn't the hard drive but in fact the power supply that was causing it. Could it really be that or is my HD really dying or is it something else?
View 9 Replies View Relatedmy computer does not starting up...so i choose to press f12 then diagnostics then it shows that no hardrive detected -warning.
View 1 Replies View RelatedI have a new computer that runs Windows7 64 bit. I have an older computer hard drive that has XP.I needed something from the old hard drive and hooked it up with the cables from the Windows 7 hard drive and it booted up and ran. I've since gone back to using the Windows 7 hard drive.How do I proceed to add that second hard drive running XP to the new computer so I can have the option of running either OS? I've read through some posts, but they all presume you are installing the OS to new clean hard drives, not have them already installed.Is it as simple as hooking the XP drive into the computer as a second drive and booting it up? Do I need to change some external setting on the hard drive to have it recognized as a slave? Will Windows 7 automatically change the boot to recognize the second OS and allow a choice at startup?
View 7 Replies View RelatedI recently noticed an issue when trying to connect to external hard drives. Initially noted that it wasn't showing in 'my computer' and so assumed I had driver issues and sought to update them from Dell's site. After doing so there was still no change, but noted that It was appearing in 'device manager'.I even tried updating the USB hubs from the Device Manager, and it states that they are all up-to-date with the correct drivers. Both external hard drives that i have tried has worked on other PC's so i assume that mine is the issue.
View 1 Replies View RelatedI am running windows 7 64 bit, and have 4 external hard drives attached (not the best way, but until I can afford a server, the only way). I am using my computer as a media center only. When I wake my computer it can take a while (30 seconds to a minute), before I can use it, due to it starting up my external hard drives, but I have noticed a couple of times, my computer will wake without starting up my external hard drives (able to use media center within 2 seconds). Does anyone know if there is a way to get my computer to wake up without starting up the external hard drives every time?
View 7 Replies View RelatedI just updated to a z77 i5 3.4 and everything has installed fine except for my creative arena headset usb. It was working just fine on my other machine earlier today but now that I have a new mobo and cpu it will not install the drivers. My SSD and HDD were not reformated and I have tried uninstalling and reinstalling the drivers a few times with no change. I just get 3 rapid beeps when I plug the USB in.
View 5 Replies View RelatedI have built many computers but am having a little bit of a problem with some things and my new one. My new install went great. All programs installed without a hitch. Fast and furious is the way it went to get everything installed. Now, after a week or so I have started having a couple glitches. When I go to install a new program or update it the program just sits there for 4 or 5 minutes before doing anything and then finally starts to do its thing. The other issue is that I am trying to do a backup and image clone to get my new system backed up. The problem there is that the windows backup won't see my hard drives. I then tried Norton Ghost and the same thing happened. What is causing this?
View 13 Replies View RelatedOutlook 2007 Task search versus Windows7 computer wide search.
I enter the same keyword (one of the words contained within the title of a completed task) in the Outlook Task search box as I do the Windows 7 orb 'search programs and files.' The Windows 7 search returns the correct search result (along with a lot other results having the same keyword) practically immediately whereas Outlook is still searching...and searching.
If I have index options set to include the C: drive and Outlook, what's going on with Outlook?
I've made the move (fresh install on new HDD) from XP to Win7RC x64 (I never gave Vista a look) and I want to scan my old HDD partitions for *.xls;*.doc;*.dwg;*.jpg etc to make sure I haven't missed any old files which were not saved in the right place.
The two partitions are mounted as F: and G:
In XP once you'd turned off the animated dog and chosen the advanced option, you could set "all of part of the filename" to "*.xls;*.doc;*.dwg;*.jpg" and "look in" to "f:;g:". It was a so easy
I can't seem to get Windows 7 to search for more than one file extension, let alone multiple drives as well. Is there an advanced search option which I've missed?
make a dualboot comp by adding windows XP to a new partition. I created the new partition with 20gb. (From the 500 of my actual harddrive)But before I actually installed on that, I got distracted with a second harddrive that my dad got(for no reason). It had a full copy of Windows XP backed up on it from another computer, so I figured I would just use that for the dualboot. I plugged it in (wired the same way as my old harddrive, but different data slot), restarted, checked the harddrive in explorer - all the data was there / reading correctly / etc, and I used 'easyBCD' to add the new harddrive to the boot list.(Which, of course, crashes if I try to start it. I just wanted to see what it would do). For a reason I can't remember, I unplugged the second harddrive for a bit, started the computer on accident (I don't know if anything loaded before I shut it off), and then when I plugged it back in.Windows 7 would not launch. It goes to a DOS-like window, except it's just a flashing _ and it never does anything even after a few minutes. XP didn't work still.. so I decided to reinstall XP (as I couldn't tell which harddrive was which on the list, I unplugged the main harddrive while installing onto the new).. and when I did this.. it formatted and installed fully... then restarted.. then restarted.. and restarted.. and just kept restarting, never showing any thing past the manufacturer logo/BIOS load-button-message-thing. So, I then try to use my 3-disk Windows7Recovery disk(burned myself with a program apparently included by the manufacturer.) It installed fully, appearing to work.. but when I launched it, it said "Invalid Partition Table" and wouldn't boot past that. When I insert my driver installer disk, it gives me a basic DOS window thing. dir A: shows the files in the disk. dir B: for some reason shows the same. C: says "Error reading from drive C: DOS area: general failure". All other letter:'s just say "invalid drive". (I'm doing this with both harddrives in.) I attempted connecting the harddrives to an old computer, but it gave an error for both. (It detected the harddrives, but said it had an error reading from it. Windows Explorer asked me to format it... {i'm willing to format one of the drives if anybody thinks it will help, but the old harddrive has data I'd prefer not to lose.} ) Looking on google, I saw several problems that all have similar problems (less overdescripptive than I am though) but none of the fixes suggested worked for me. Also - as I have two different with different errors, I only need to make one of them work.)Also - my other available computer has a CD burner / floppy drive if either are required. I also have several USB's. The computer can boot from USB's and CD's (tested), and I could easily take the floppy thingy and connect it to the computer.also - this computer is probably still under warranty unless unscrewing the hard drive voids it. .. does that count as modification of the computer?
View 5 Replies View RelatedI have been doing some searches using the search box that comes up when you press the colorful button on the bottom left. It finds nothing. I can have folders and WORD documents on my desktop, and it always comes up now with nothing found. If I create a test Folder, or WORD document, put on the Desktop, it won't find them. Always used to work fine. Only difference now is that I put in a new HD after the old one failed. Everything else seems to work fine.
View 1 Replies View Relatedi built me a gaming computer with windows 7, its up and running. I have a old Dell with Windows Xp that i have had for 5 years. I want to put that hard drive in my new computer. is this possible? will there be any conflicts? I want to make it so maybe in bios i can select witch OS to boot up. Or maybe it defaults to Win7 and i can switch to WinXp whenever i wanted.
View 5 Replies View RelatedI've recently purchased a PC with 1 64GB SSD and 1TB HD. Contrary to instructions the seller uploaded everything onto the SSD at C: and not just the OS. He now says I should use a disk partitioner to transfer the files. Also to reset my BIOS.
View 5 Replies View RelatedI currently have a dual boot of Windows Vista Ultimate on one hard drive and Windows 7 RC1 on the other and was planning on
upgrading to Windows 7 ultimate. I have could either upgrade my Vista hard drive which would be easy or I could upgrade the release candidate Windows 7 which is a fresh install on a new drive. Which should I put Windows 7 on?
If I Format my Hard drives ,do I lose all my systems ,Like Windows???
View 4 Replies View RelatedI have two laptops that are identical...HP Compaq nw9440. I have a 100gig drive in LAPTOP#1, and a 750gig drive in LAPTOP#2. Both drives are running an identical Windows 7 Enterprise typical install. Can I put the 750gig drive in to LAPTOP#1? Can I create and save an NTBTLOG.txt file from each laptop (I.E. ntbtlog-LP1.txt) and select either one during the boot-up? The reason is LAPTOP#2 is not running very well. It has been dropped and I fear the motherboard may have a crack in it causing random boot problems. Sometimes the laptop doesn't even recognize the hard drive.
View 2 Replies View Related64installed on c, win 7 later installed an d. dual boot has been working perfectly until
something caused the drives to switch. now win 7 starts ok but looks for all it's files on c, which is locked.
vista starts up fine, and sees all it's files on c as it should.
my windows 7 repair disk, created at start of win 7, does not correct problem, nor does system restore.
After upgrading, I've found that I have 7 IDE hard drives ranging in size from 1 GB (!!!) to 200 GB. I'd like to get rid of them all. Is there a free reliable recylcing service out there. I've already wiped them clean (except for the 1 GB drive which won't spin up. It's from 1994).
View 7 Replies View RelatedJust added this to my computer Safely Remove Hardware Shortcut - Create
and when I try and eject using the right click on the desktop I get
Problem Ejecting XXXXXx USB Device
The 'XXXXXXXXX' device is not removable and cannot be ejected or unplugged
This is when I try any combination of clicking stop on the drive name and drive letter in the window.
I can only run one at a time instead of two. I would like to copy my 1.5tb over to my 2tb so I have a back up.
My laptop only holds 200GB of remaining data so I can't use that hard drive or I would.
This morning my pc started acting up for some unknown reason. After numberous attempts to fix it, I decided to restore from a restore point. It said it did restore but things got even worse.I then decided to restore an Maxium Reflect image I had made a couple weeks ago. When I made the image, the pc was working fine. The restoring of the image went normally.I have two strange things occurring.
1. I have two hard drives with 3 partitions on each drive. After about 10 minutes I can NOT see second hard drive in either windows explorer or Disk Managaer.
2. When the pc is first booted and a few minutes pass, I get what sounds like a radio station playing. It only lasts for about 20-30 seconds then goes off. It comes back randoms times. I have checked the processes that are running and nothing stands out that would cause this.I built this PC in 2009 and the combination of these identical hard drives (1 TB Sata) have always acted strange at times. Example the second hard drive would NOT always boot when windows booted. This was usually fixed by just rebooting.I have checked and all fans are working normally and inside the case is relatively clean.Is there any software that can be used to check hard drives???
I blow away a computer so I'm taking the Hard Drive out and putting it into another computer. From a AMD 3000 to a AMD 3800 and all it does in re-boot. I put in the XP CD and tried to do a repair but it didn't work or I didn't do it right.
View 3 Replies View RelatedI have a slight issue that I'm not sure how to fix. It's nothing serious but it's something I'd like to take care of.
Basically, I bought a new hard drive, made it the primary drive, and kept the old one in so I could transfer everything over to the new one and keep the old as my backup drive.
I installed Windows 7 but when I boot my machine without the disc in the drive it wont boot. I made my old drive the primary one again and I discovered that when I installed Windows 7 it put the boot information on the old hard drive instead of the new one.
Basically, I'm looking for an easy way to get it to boot from the new hard drive without having to use the old one as the primary. Any ideas?
I have a laptop that came with Windows 7 home premium and one hard drive. I purchased a second hard drive and installed. Is there anyway to set this up, even if it means wiping everything and reinstalling, so that both hard drives are seen as one C drive? My laptop does not have a RAID option in the BIOS. What about if it was Windows 7 professional?
View 9 Replies View RelatedIf you think that switching to the high performance power plan is enough to set your computer to the best plan, well, it isnt.
Heres how to set your hard drives so they are included in the high performance:
1. open control panel
2. type power in the search bar and click "change power-saving settings"
3. to the right of the plan name click "change plan settings"
4. Click "change advanced power settings"
5. Go to the hard disk section and then "turn off hard disk after"
6. Enter 0 (zero) in the box (this will change to never)
Doing this prevents your disks from being "turned off".
