I have a laptop that came with Windows 7 home premium and one hard drive. I purchased a second hard drive and installed. Is there anyway to set this up, even if it means wiping everything and reinstalling, so that both hard drives are seen as one C drive? My laptop does not have a RAID option in the BIOS. What about if it was Windows 7 professional?
make a dualboot comp by adding windows XP to a new partition. I created the new partition with 20gb. (From the 500 of my actual harddrive)But before I actually installed on that, I got distracted with a second harddrive that my dad got(for no reason). It had a full copy of Windows XP backed up on it from another computer, so I figured I would just use that for the dualboot. I plugged it in (wired the same way as my old harddrive, but different data slot), restarted, checked the harddrive in explorer - all the data was there / reading correctly / etc, and I used 'easyBCD' to add the new harddrive to the boot list.(Which, of course, crashes if I try to start it. I just wanted to see what it would do). For a reason I can't remember, I unplugged the second harddrive for a bit, started the computer on accident (I don't know if anything loaded before I shut it off), and then when I plugged it back in.Windows 7 would not launch. It goes to a DOS-like window, except it's just a flashing _ and it never does anything even after a few minutes. XP didn't work still.. so I decided to reinstall XP (as I couldn't tell which harddrive was which on the list, I unplugged the main harddrive while installing onto the new).. and when I did this.. it formatted and installed fully... then restarted.. then restarted.. and restarted.. and just kept restarting, never showing any thing past the manufacturer logo/BIOS load-button-message-thing. So, I then try to use my 3-disk Windows7Recovery disk(burned myself with a program apparently included by the manufacturer.) It installed fully, appearing to work.. but when I launched it, it said "Invalid Partition Table" and wouldn't boot past that. When I insert my driver installer disk, it gives me a basic DOS window thing. dir A: shows the files in the disk. dir B: for some reason shows the same. C: says "Error reading from drive C: DOS area: general failure". All other letter:'s just say "invalid drive". (I'm doing this with both harddrives in.) I attempted connecting the harddrives to an old computer, but it gave an error for both. (It detected the harddrives, but said it had an error reading from it. Windows Explorer asked me to format it... {i'm willing to format one of the drives if anybody thinks it will help, but the old harddrive has data I'd prefer not to lose.} ) Looking on google, I saw several problems that all have similar problems (less overdescripptive than I am though) but none of the fixes suggested worked for me. Also - as I have two different with different errors, I only need to make one of them work.)Also - my other available computer has a CD burner / floppy drive if either are required. I also have several USB's. The computer can boot from USB's and CD's (tested), and I could easily take the floppy thingy and connect it to the computer.also - this computer is probably still under warranty unless unscrewing the hard drive voids it. .. does that count as modification of the computer?
I had a striped hard drive set up because I thought it was cool to make 2 500's a 1 tb. it broke. but now one of em went off the reservation and now wants to be a cd drive after reformatted the drive that was working.can't see the errant drive in disk management but in computer (windows 7, custom build) it's my new cd drive witch claims to be my H: drive.
I have two 1TB drives, each containing 4 partitions, used for backing up 4 computers. These drives are regularly switched between buildings as part of our backup strategy, always having one off-site. I have assigned drive letters M,N,O,P to respective partitions. When I swap the drives, the drive letters get reset and have to be manually reassigned. assigning the drive letters, including USBDM, but get no results.
Computers: HP Compaq 8200 Elite - CMT - 1 x Core i5 2500 / 3.3 GHz - RAM 4 GB - SSD 1 x 160 GB - DVD�RW (�R DL) / DVD-RAM - HD Graphics 2000 - Gigabit Ethernet - Windows 7 Professional 64-bit - Intel vPro Technology Docking Stations: ICY DOCK MB877SK Hard Drives: SAMSUNG Spinpoint F3 HD103SJ 1TB
I am running windows 7 home 64 bit (build 7600). I have a gateway fx7026. It has two internal hard drives. When I look under device manager they are both listed and they are both listed under the bios menu. When I look in my computer though under hard disk drives it only shows the one that I have the OS on. When I had Vista it showed both of them. Is this something I should be worried about. The drives are listed as WDC WD3200AAJS-22B4A0 DRIVE 1 and WDC WD3200AAJS-22B4A0 DRIVE 0.
I am using 3 external hard drives and noticed a couple of times there drive letters have changed. Maybe I have had them unplugged for some reason I cannot remember, but it causes confusion with some files that use shortcuts. I would like to know if it is possible to give the drives permanent drive letters also change there names?
I upgrade my pc with SSD everything seem to go fine but 2 of my 2TB drive giving me a Smart error now. i wonder if SSD has anything to do with Drives failing. My theory is that.
SSD runs on a flash based chip ... it is very stable but mean time it has huge access point of data that why it is fast. The reason i am thinking that SSD is killing my other drives is because my setup is a Media center. Software such as windows media center and media browser keep accessing my 2 TB Hitachi drive for movies, TV show and so on .. SSD in my opinion is running other drive to max point of spin and read/write in same time. which could caused these drive either over heat or over used that is just a theroy of mine
MY Setup : Media center pc with 4 2TB Hard drive Hitachi and 1 60GB SSD drive
after searching for some answers on the forums, i've been moved to post a separate thread. i have an external hard drive that disappears for some seconds only to reappear again on my list of drives. my computer alerts as if the external drive were dismounting then remounting. i have run various checks and nothing is presenting as abnormal or of issue. has anybody else experience this, what effect is it having on my computer and what can be done about it
I use a lot of different usb hard drives in my shop. I have two basic enclosures, a generic one that uses pata drives on a usb 2.0 cable and an Apricon USB SATA 2.0 adapter.Suddenly when I plug in a new drive device manager does see the drive and installs it in device manager. I can see the drive in Disk Management but it has no drive letter assigned, and therefore doesn't show up in Computer. I can easily just assign a letter in Disk Management and the drive immediately becomes usable. However, I would like to get Windows 7 to resume automatically assigning a drive letter.
I have tried a program called USB DriveCleanup. What it appears to have done is remove all installations of prior USB drives and when I plug in a drive that has been in the machine previously it then goes thru the install again. Yet still no drive letter. I think the program is doing what would manually be done by going into safe mode and cleaning out all the entries that build up there that don't appear in normal mode, then removes them. Basically it seems like a shortcut to manually doing it.
I also tried a registry fix that essentially asked me to delete the upper and lower filters. This seems similiar to fix for CD/DVD drives that no longer appear in Computer. This fix also didn't work.I tried removing and reinstalling the chipset drivers. Still no go.Running Windows 7 Pro SP1, H55 chipset.
I have a hard drive I want to backup to a 64gb flash drive and then restore it to another different hard drive than where it came from. I have windows 7 and office on my laptop and I want it on my desktop pc. There isn't close to 64gb of info on my laptop so it should be fine even though the hard drive says I have 160gb. It is all free space except for those programs.
So, I have a i7 2600K system with a solid state disk as the boot drive, and an older (c2008) Samsung Spinpoint F3 500GB drive as the data drive for programs (that I deem as not worthy of the quick load times). The hard drive has given me some errors over time, and I bought a hard disk to replace it (a Hitachi 1TB). The issue I'm having is that the fact that Windows 7 puts a small (100MB) partition on the F3, and for some reason, even though I'm running Acronis 2012, it doesn't seem to be able to clone the F3 over to the Hitachi. I've also tried Drive XML, and for my 2 hour wait, I only managed to acquire a boot error. Thankfully, I've not done anything rash to destroy the data on the F3, but given the fact that I've seen corrupted files in Steam from that drive, I'm not will to trust it long term with my data. I really need to get the data onto that Hitachi, though... Anyone have any advice for upgrading the HDD in a SSD/HDD system? I don't really feel like it should be so hard, especially if I've bought Acronis True Image, but maybe they haven't designed their product to handle this scenario quite yet?
i built me a gaming computer with windows 7, its up and running. I have a old Dell with Windows Xp that i have had for 5 years. I want to put that hard drive in my new computer. is this possible? will there be any conflicts? I want to make it so maybe in bios i can select witch OS to boot up. Or maybe it defaults to Win7 and i can switch to WinXp whenever i wanted.
I've recently purchased a PC with 1 64GB SSD and 1TB HD. Contrary to instructions the seller uploaded everything onto the SSD at C: and not just the OS. He now says I should use a disk partitioner to transfer the files. Also to reset my BIOS.
I currently have a dual boot of Windows Vista Ultimate on one hard drive and Windows 7 RC1 on the other and was planning on
upgrading to Windows 7 ultimate. I have could either upgrade my Vista hard drive which would be easy or I could upgrade the release candidate Windows 7 which is a fresh install on a new drive. Which should I put Windows 7 on?
I have two laptops that are identical...HP Compaq nw9440. I have a 100gig drive in LAPTOP#1, and a 750gig drive in LAPTOP#2. Both drives are running an identical Windows 7 Enterprise typical install. Can I put the 750gig drive in to LAPTOP#1? Can I create and save an NTBTLOG.txt file from each laptop (I.E. ntbtlog-LP1.txt) and select either one during the boot-up? The reason is LAPTOP#2 is not running very well. It has been dropped and I fear the motherboard may have a crack in it causing random boot problems. Sometimes the laptop doesn't even recognize the hard drive.
After upgrading, I've found that I have 7 IDE hard drives ranging in size from 1 GB (!!!) to 200 GB. I'd like to get rid of them all. Is there a free reliable recylcing service out there. I've already wiped them clean (except for the 1 GB drive which won't spin up. It's from 1994).
This morning my pc started acting up for some unknown reason. After numberous attempts to fix it, I decided to restore from a restore point. It said it did restore but things got even worse.I then decided to restore an Maxium Reflect image I had made a couple weeks ago. When I made the image, the pc was working fine. The restoring of the image went normally.I have two strange things occurring.
1. I have two hard drives with 3 partitions on each drive. After about 10 minutes I can NOT see second hard drive in either windows explorer or Disk Managaer.
2. When the pc is first booted and a few minutes pass, I get what sounds like a radio station playing. It only lasts for about 20-30 seconds then goes off. It comes back randoms times. I have checked the processes that are running and nothing stands out that would cause this.I built this PC in 2009 and the combination of these identical hard drives (1 TB Sata) have always acted strange at times. Example the second hard drive would NOT always boot when windows booted. This was usually fixed by just rebooting.I have checked and all fans are working normally and inside the case is relatively clean.Is there any software that can be used to check hard drives???
I blow away a computer so I'm taking the Hard Drive out and putting it into another computer. From a AMD 3000 to a AMD 3800 and all it does in re-boot. I put in the XP CD and tried to do a repair but it didn't work or I didn't do it right.
I have a slight issue that I'm not sure how to fix. It's nothing serious but it's something I'd like to take care of.
Basically, I bought a new hard drive, made it the primary drive, and kept the old one in so I could transfer everything over to the new one and keep the old as my backup drive.
I installed Windows 7 but when I boot my machine without the disc in the drive it wont boot. I made my old drive the primary one again and I discovered that when I installed Windows 7 it put the boot information on the old hard drive instead of the new one.
Basically, I'm looking for an easy way to get it to boot from the new hard drive without having to use the old one as the primary. Any ideas?
As my hard disk, I have a 1TB Western Digital Caviar Black Edition.. it's 7200RPM, 32MB cache. Yet, WEI only gives it a score of 5.9. Everything else on my PC is a 7.0 or above.. any reason for that?
Any trick on how to get windows7 to keep seeing your slave drives?
I have tried un-sleeping, increased time to 999min. All drives have drive letters & are listed as active and healthy etc. Each have mix of ide but mostly sata drives. Windows have been updated.
I have a small office with 8 computers trying to run Windows 7 now. All fresh installs onto new sata drives @ 2 weeks now. (The old xp drives was just turned off awaiting reformat). Everyone is starting to have the same problem with drives that disappears. On some of the computers it happens as quickly as in 5 min, sometimes right as you moving one file on one drive over to another drive. Nothing but rebooting all day.