My laptop won't install my USB mouse when i plugged it into my second USB port. It only works in my first USB port when i first restored my windows 7. I tested using my pendrive in the second port and its working just fine. However, when i tried to use my mouse in the second port, it wont work, even the broadband which I am trying to use in that port.I recalled clicking the option "skip searching for drivers from windows update" coz i was on a slow net at that time and was kinda in a hurry, so yeah. Is there any way to make my laptop re-install the drivers in it coz my wild guess is that I chose not to install it last time so it wont try to auto install the drivers again.
I usually plug the receiver into a certain USB port on my laptop (HP HDX-18t, Windows 7 Ultimate 64-bit) and the mouse works fine. After a while, from an hour to several hours, the mouse pointer will become jumpy and then become completely unresponsive. When that happens, the power light on the receiver is no longer lit. Then I have to disconnect the receiver and plug it into another USB slot. The mouse will begin to work again, but then the same failure occurs. Then I repeat this over and over, "chasing" the ports until I finally plug the receiver into the first USB port again.
I should also mention that when the failure occurs the first time, if I disconnect the receiver and then plug it back into the same slot, I get a "device not recognized" notification in the system tray. This error never occurs with other ports, only the first. Also, I can immediately connect some other USB device to the port(s) the the receiver failed on and they'll work fine.
I have a new pc with a Gigabyte GA-H67MA-UD2H-B3 motherboard and I plugged a Microsoft 600 Wired Keyboard into the rear port (designated for KB/Mouse by Gigabyte). The keyboard works in the BIOS, but when Windows 7 loads, the num lock light switches on, then Windows 7 says that "Driver not installed properly". In the Devices & Printers window, it shows an icon of the keyboard with a yellow exclamation mark and says "hardware not available". However, mouse continues to work. This happens in all the rear USB ports. If I plug the keyboard in the front port, Windows recognizes the keyboard, install the correct driver and it works! All the USB ports work fine otherwise (tested with thumb drive as well as mouse). I also tried with a Logitech K120 wired keyboard which also had the same problem.!!
So I was having some audio problems with my computer so I figured updating the drivers would be the best bet. I decided I'd use one of those programs that can check your driver and download the driver you need. I followed the instructions and installed what seems to be called AmdEHCI onto my computer. Now whenever I turn on my HDTV which I have connected via the HDMI on my ATI Raedon 6950 the audio claims that it is not connected. Now every time I want audio to come out of my HDMI I have to disable to display and then re-enable it. I used to be able to turn my TV on and off whenever I wanted and I would still have audio functioning properly.Something that caught my attention was that when I left the properties window opened for the HDMI audio and then turned on my TV I would get a message that says "The device you are configuring has been removed." even though I haven't touched anything other than the power button on my TV to turn it on.
So today i installed the drivers for my razer deathaddder mouse on my laptop. The installation went fine, but the problem is it seems to have taken over or just messed up the configuration for my touchpad. After installing, the touchpad moved really slowly even though i hadn't changed any settings, and the acceleration had turned off.I decided to uninstall the drivers to reverse the problem, but it didn't change. I then uninstalled and reinstalled the touchpad drivers (latest synaptics drivers, same ones i had installed before), but this didn't solve anything either. I've tried fiddling around with the mouse settings but everything is configured the way it was before, it's just not the same.I want my touchpad to go back to the way it was. Is there any way to get all the mouse settings back to the way they were when i installed windows or something like that?
Just got windows 7 on my computer. Was running windows xp before. Ive been using the mouse i am now for over a year with no problems. Now since i went to windows 7, it often stutters when doing anything on my computer. The stutters usually are about a second long and are completely random. I could be playing a game, browsing the web, or anything else and it will stutter. When it does stutter, i do hear the "bu-dum" sound as if it was being disconnected/reconnected instantly. Sometimes the stutters dont happen for an hour, sometimes i get 5 within 15 seconds. I've tried installing drivers and what not.
I recently installed new software that requires port 8080 to function. When I try to run the software I get an error that port 8080 is being used.How do I check to see what process is using port 8080 so that I can open up the port to run the software? MACHINE: Windows 7x64
I just bought a new computer from a computer shop. It is custom built and has the following:Has 8GB RAM, 3.3ghz intel core i5-2500k, windows 7, Intel HD graphics so upto 1.7GB max video memory, 1 VGA slot, 1 DVI slot.Just to confirm I checked in person and my tower has a VGA port and a DVI-D dual link port.
my 2 no usb port and lan port are not working other wise other 1 no usb port working this is new laptop i think driver not installed because when i connect the pendrive there was light showing in my pendrive.so i want drivr
My computer qwill freeze for a few seconds followed by system lag which seems to get worse (freezing every few seconds/taking 2 seconds to recognise a click etc.). If i reset my computer it resolves the issue but i was hoping you guys may be able to give me more insight as to what the issue may be.It nearly always happens when i am browsing in firefox. Have never had it happen to me during gaming etc. which is why i'm hesitant to believe it is to do with my GPU or it's drivers which are always kept up to date.i have included pics of the cursor and what processes were running at the time of the freeze/lag
Lately I have been having an annoying problem with my wireless mouse. For some reason the pointer will lag, and be very sluggish and jumpy. I've had this mouse on this computer for about a year and I've had no problem. Out of nowhere this problem is happening. I've tried re installing drivers with no luck. I tried uninstalling intellipoint and re-installing it, but when I tried I got the BSOD, and then it completely disabled my mouse and keyboard so I had to use wired peripherals to go in to safe mode and do a system restore. Now everything is working again, except my mouse is still jumpy.
i'm trying to order something from a website and the cursor want open my cart for me to look at it and finish my order. this is happening in several sites not just one.
i had installed windows 7 in my laptop,but accidentally i installed it in D-drive,now both C & D drives are showing program files,program files x86,windows folders,my D drive is full
Is it possible to turn the mouse acceleration on only when using the touchpad on my laptop and off when I'm using the mouse? I usually don't use the touchpad when the mouse is plugged in if that's an
I probably spilled some coffee on the keyboard and now I can not inactivate the mouse pad in favor of the external mouse. The only way I can eliminate the conflict is to uninstall the mouse pad. That works fine but every time I reboot for something I have to uninstall it again. As you know rebooting is common and therefore I have to reboot twice for every time I have to reboot. Anyone with a solution to this problem? This is a HP laptop. The mouse automatically installs everytime I have to reboot. I do not shut down normaly.
I have a W7 64b laptop.My mouse has started having problems, first it didn't click on things when i pressed it but if you persist it does no no big harm there. Biggest problem I am facing is the mistaking of the wheel with mouse 1. Some times when I am browsing the net and i have to scroll, and generally every time I move my mouse fast, it automatically presses the wheel. It is getting really annoying and I dont know how to stop it. I changed the mouse with another,and I had the same problem.I dont know what to do.I believe its a virus but pc didnt find anything with avast.
I'd like to have 2 mouse pointers locked inside 2 different windows and also have my keyboard inputs being active on both windows at the same time.Imagine 2 notepads open with the size of half screen each, and have 2 mouse pointers controlled at same time by the same mouse for each of the windows and typing in both notepads at the same time.whats the program called?
I have a TT esports theron its a nice mouse but for some reason it no longer reads it as such. Whenever i plug it in it reads it as HID-compliant mouse. Which doesnt allow me to use the program and set the extra button commands. How can i go about fixing this?
ok well i spent about 3 hrs and i know its not my router and its the os and i did a fresh install too im on 7600 rtm, now i got windows firewall and defender disabled, i got nod32 antivirus not with a firewall just the anti, now i got utorrent, so i use utorrents port checker, the port works for it but if i add a port to my portforwarding on my router it dont work, according to this port scanner, now if i enter it and use it as my port in utorrent it works! but anything else doesnt i dont get it i got windows firewall disabled and all that i literally think theres a hidden firewall or a virus but i know there isnt a virus i also did a scan incase so any ideas?
I literally cant press the "change settings" button in windows 7, (im using windows 7 RC), its dull and theres nothing i can do, trying to connect to spore if your wondering.
My computer crashed about a month and I want to format it. When I plug in the keyboard to go into bios it does not work. if i plug in anything at all it doesnt work, every usb port that is.
Last night my new laptop arrived (XPS), still getting used to windows 7 etc... but i thought i would watch something through my t.v. Plugged HDMI cable in back of laptop straight in to t.v, changed the source and straight away i had a lovely sharpe picture of my deskop instantly.... or so i thought
im getting the middle part of my screen fine - but it is cropped so i cant see the tool bar (its too low) and the desktop icons are only veiwable if i move them closer in screen! Ideally i want to have identical screens on both so i can use both at sam time, but currently i can only view either or atm? and the t.v one being crop means i can use it as a computer (No toolbar etc..)
I could figure this out on XP but windows 7 seems beyond me atm!
I have some crazy problem with port 80 . Everything was fine since last 5-6 days. When i try to connect to some pages i get this note on picture.
i tried every posible browser and same thing ! also tried disabling firewall and nothing ...problem is still here! this is only one of many pages that i cant load.
To all the computer geniuses out there, I guess this isn't a windows 7 problem but it's about drivers.I have an Asus K53E-B1 with Windows 7 64bit. It comes with 3 USB 2.0 ports and that's it. I went on the Asus website today and found USB 3.0 drivers update.I can't just download those drivers and use them and expect USB 3.0 performance when I have USB 2.0 ports right?
I have a quick question about the USB ports on my computer. I have a screenshot hosted here on Flikr: USB | Flickr - Photo Sharing! Of the 5 USB's that are listed, one is a USB2. Is the USB2 Enhanced Host Controller a USB2.0 port? I am looking because I am going to buy an audio interface and if I have a 2.0 in there then I will get something a little better 'cos I want as little latency as possible when recording vocals.
There is one other thing also, if it turns out that there is a 2.0 port, is there a way to physically differentiate which port is the 2.0? I have 3 USB's on the back and 2 on the front of my tower. At the moment I don't know which is which and do not know what to physically look for when I look in or out of the case.
I have an application to control external devices via IRDA.The application only accepts IRDA connected via a serial port.I only have a USB-IRDA device.
Is there any freeware driver/software to create a virtual serial port and link it with the USB device?
