Samsung SGH-Z810 Not Recognized
I installed Windows 7 on my toshiba notebook. Everything is fine, but I cant use my 3g modem. The samsung sgh-z810 works on vista and xp.
on xp and vista, when i plug in first time to machine, it install a virtual cd, and run setup.exe from it (it is modem's the flash ram). after setup xp and vista recognize this hardware as modem (and card reader) and works.
on Windows 7 after the first step (when setup.exe closed) the Windows 7 doesn't recognize the modem. the modem is not listed on device manager...
i read, that will works if i make virtual xp mode, but my laptop not support this mode.
i saved the drivers from XP with driver-magician, but i cant add device to the device manager. the hardware not shown in the list.
i want to "add as older hardware" to add device in device manager, but i cant use the driver .inf files. when i click on it, the device's list is empty, can't choose from the manufacturers / devices list.
i can use modem if i run virtual machine with installed XP on windows 7, but Windows 7 "alone" cant recognize this s h i t.
View Replies (Posted: 11-07-2009)
Sponsored Links:
Related Forum Messages for Windows 7:
Modem Samsung Sgh-z810
USB modem Samsung sgh-z810 works in Windows 7. 1. connect modem to USB, install all required drivers and software (if don't work, use compatibility mode with Windows XP) 2. install VMware Workstation 3. install Windows XP on VMware Workstation 4. run XP and install all required drivers and software for modem (it's automatic) 5. now you have internet on running Windows XP on VMware Workstation 6. disconnect from internet on Windows XP 7. run connection manager on Windows 7 8. and now trick, add new HW (VM>Settings>Add>Network Adapter>Host-only>Finish) Network Adapter 9. wait few seconds and connection manager find modem on windows 7 (WTF?) 10. now, you can connect to the internet using connection manager in Windows 7 11. close VMware Workstation and enjoy ;-) I don't know how it's possible, but it works! Cheers!
Posted: 09-27-2009
View 6 Replies!
View Related
Samsung SGH Z810 Compatibility
Is someone using samsung sgh-z810 usb (3G, HSDPA), modem successfully with windows 7? I am trying to use it on my MSI WIND U-100 notebook. Windows 7 is running well on the notebook, I have no other complains or hardware issues. I am running the official evaluation copy Build 7100 downloaded from Microsoft. The modem installation consists in the following steps: (For testing purposes I've installed successfully under XP and Vista, the modem is working well) 1 - Plug in the modem in one of the USB slots 2 - The hardware is recognized as CD-drive (this is normal) 3 - The autoplay function starts, installing setup.exe - which installs Samsung's connection manager software 4 - after the installation of the connection manager software the system recognize the modem part of the device and installs the drivers from the "CD"-drive (from itself) 5 - after successfully install, the connection program runs from the pc and that's all. Under Windows 7 I can do the install until the step 3 - installing the connection manager software. In order to solve my problem I already did the following: - installing from the scratch (one by one) using the compatibility mode set to all of the XP-modes and all of the Vista modes - also running as administrator. No matter whatever I did, the system is not recognizing the modem part of the device (it is not included in the list of the devices - not even like unknown device) I would be more than happy if someone could help me to solve this problem PS: I did search for upgraded samsung software and drivers, but I couldn't find anything the device is not even listed on samsung's web-pages. I purchased the modem from official Hungarian mobile service provider.
Posted: Saturday, June 20, 2009 4:36 PM
View 1 Replies!
View Related
Samsung SGH I900 Driver
Windows Vista recognizing my phone: Samsung SGH i900 Omnia successfully and syncs via USB connection! After I migrate to Windows 7 and found that no driver for SGH i900?!? If anyone knows where it could be downloaded for SHG i900 driver I would be very grateful to him!
Posted: 11-24-2009
View 4 Replies!
View Related
Support For A Samsung, Eternity SGH-a867
I was using Samsung's PC Studio to sync my Eternity cell phone with Outlook but they are not going to support Windows 7 with a USB driver. I have set up my computer to run in XP mode but still cannot connect my phone. I guess if I can't get this to work I will have to buy a new phone running Windows Mobile. How do I get my computer to recognize my cell phone's USB port in XP Mode?Â
Posted: Saturday, December 05, 2009 7:06 PM
View 6 Replies!
View Related
Samsung SGH-a867 Eternity Driver Install
Thus far, this method works on builds 7057 and 7077 x64. I can't imagine it working any differently on x86. I did have to re-perform the driver reinstall (step 5+) after I upgraded from 7057 to 7077. First: KEEP YOUR PHONE UNPLUGGED FROM THE COMPUTER Second: Download and Install Samsung PC Studio 3.2. The version I've downloaded was "Samsung_PC_Studio_321_GL6.exe" (MD5: 55B2561750C25BC0453DA9DDBD7DA216) for now it looks like you can still get it from here: http://downloadcenter.samsung.com/co...io_321_GL6.exe. Install the software. (note: Do not download and install that new version 5 crap, PC Studio 3 is already bloated enough and it sucks we're forced to use their interface, but the version 5 came with crashing 'usb com port' services and more bloatware) Third: Execute PC Studio's Automatic Updates Allow it to update what it wants (at the time of this writing, it won't ask you to update to version 5) or the program will bug the hell out of you. Who knows, you can probably do fine without the updates, but I'm telling you how I got it to work. Once complete, Close Samsung PC Studio 3. Fourth: Plug in your Phone with the USB cable. Windows will go Beeedoop and Baaadump. It will ask to find a driver online and it will fail. Just cancel out of everything. Fifth: Open up the Device Manager - I shouldn't have to include this section if you're Method 1: Run devmgmt.msc Method 2: If you have "My Computer" on your desktop, Right click on it, Click on Manage, Click on Device Manager on the Left Bar. Method 3: Click on the Start Menu, Right click on Computer, Click on Manage, Click on Device Manager on the Left Bar. Sixth: Install the SAMSUNG Mobile USB Modem Driver Under Other Devices, Right click on SAMSUNG CDMA Technologies, then click on Update Driver Software. Click on Browse my computer for driver software. Then click on Let me pick from a list of device drivers on my computer. Click on Next. Click on Have Disk. Navigate to Samsung's Drivers folder. For me, it was in C:Program Files (x86)SamsungSamsung PC Studio 3USB Drivers2 Select ssm_mdm2.inf Click on OK. If Given a Choice (I seem to remember having to choose, but when I replayed this, it only gave me this one) click on SAMSUNG Mobile USB Modem and not the other ones (I think one of them said Com Port and the other just USB drive.) They will install properly, but they won't communicate with Samsung PC Studio 3, rendering them effectively useless. Ignore Warning. Click on Yes. Windows has successfully updated your driver software! Click on OK. Finally: Open Samsung PC Studio 3. On your phone, navigate to the "Main Screen" (keep pressing the End-Call Button till you get home) and in a few seconds it should say SGH-A867 connected on the bottom right. If not, click on File > Connection, then click on USB, then click on Connect.
Posted: 04-14-2009
View 4 Replies!
View Related
New Harddrive Not Recognized
I bought a new WD scorpio blue for my hp laptop. backed up all the data on my old hard drive, removed it, and put the new hard drive in. windows is not seeing it, and i'm not sure the bios is either. please help! i'd like to use the new harddrive (bigger capacity) instead of the old, but i don't understand how to have the system know the harddrive is there. the laptop is an hp compaq 8510w. i had Windows 7 running it on for about 4 months. the new harddrive is the western digital blue scorpio 500gb.
Posted: 10-19-2009
View 1 Replies!
View Related
Bluetooth Not Recognized
After switching from XP to Windows 7 on my Dell XPS M1210 I can't get Bluetooth file transfer to work with phone and other laptop. Troubleshooting doesn't provide answers. Which Bluetooth driver do I need to download and where do I find it? Any solutions please?
Posted: Saturday, January 02, 2010 12:28 AM
View 2 Replies!
View Related
Samsung TV Not Supported
I upgraded from Windows Vista to Windows 7 in my HP Pavilion dv2415NR the screen on the laptop works fine when I tried to send the video to my Samsung 40 TV I get a message on my TV that the "mode not Supported". The Samsung work under Vista. Any suggestions of how I can get to work. I tried downloading the new driver from NVIDIA.], that did not solve the problem.
Posted: Monday, January 11, 2010 12:21 AM
View 2 Replies!
View Related
DLNA Samsung TV
I have a Samsung LN40A750 TV and apparently for the "A" versions you can no longer get the linkstick. I ordered a "B" version of the linkstick but it didn't work (it said it wouldn't but I figured I'd try it anyway). In the end I settled on purchasing a Linksys WET610N Wireless bridge. That worked as the TV has an IP address and I can use WiseLink to see the content being shared from the computers on my network. The PLAYTO feature in Windows is what really want to work with this lashup but the TV is not recognized by Windows 7 as a device.  Any thoughts on how to get the TV to be recognized as a device while connected to the bridge? Is this something provided by the linkstick for this TV? BTW, it does identify the WET610N wireless bridge as a device in Windows. I have a Samsung Omnia 2 phone. It too is DLNA compliant and I can PLAYTO that device.
Posted: Saturday, January 09, 2010 11:11 PM
View 8 Replies!
View Related
CD Drive Not Recognized After Reboot
I'm using a Dell laptop Studio XPS 1640. Ok, I was about to upgrade to Windows 7 and it listed a couple of programs that needed to be deleted, so I uninstalled them. The 2nd or 3rd time I was required to restart my computer, it froze at the "Shutting Down..." screen for about 20 minutes. I waited and waited and decided to power down. I turned it back on, and it didnt say Windows was not shut down properly, so i figured it was ok. However when I booted back up, I was going to eject and re-insert the upgrade CD. I hit eject, nothing happens. Hit eject again, nothing happens. I go to Computer to try and view the CD thats in my CD Drive....NOTHING SHOWS UP! MY CD drive is now UNRECOGNIZED by my computer! Now I cant complete the upgrade. Not to mention, the upgrade made me uninstall itunes and my virus protection, saying a new version will be installed automatically after the upgrade.
Posted: 3 Weeks Ago
View 1 Replies!
View Related
Second Drive Not Recognized With Win7 RC
I have an AMD 64 (single core) processor based machine. Â It recently became my 'second' PC for testing. Â Previously Windows XP Pro was installed an used for a few years. Â This PC has two IDE hard drives. Â THe system in on the first drive, the second is for data only. Â With XP this was, of course, no problem.
Posted: Wednesday, May 13, 2009 1:26 AM
View 5 Replies!
View Related
Mouse Freeze Up Or Is Not Recognized
I have been testing Windows 7 Beta with all of the updates on an Insperion 600m. Surprisingly it worked fine and ran Office 2007. Suddenly my mousepad pointer locked up. I shut the computer down and connected a wireless mouse with no correction to the problem. I shut down a second time and connected a wired mouse and restarted the computer again. Again the mouse was motionless. Beside three dead mice what could be the problem?
Posted: Monday, May 25, 2009 8:30 PM
View 3 Replies!
View Related
ESATA Drives Not Recognized
I have Windows 7 Ult. and been having problems with my ESATA drives. If i dont use the computer for so long not to sure how long but seems like over 4hrs the ESATA drives are not in my computer's folder and can't get them recognized unless i reboot my system. I do not use the sleep or hibernation and i did turn off hardisks from sleeping under power settings. I have power setting to stay on all the time for everything but still my ESATA drives disappear.
Posted: Thursday, November 05, 2009 2:28 AM
View 4 Replies!
View Related
SCSI Drive Not Recognized
I've got my system installation on a SCSI harddrive and wanted to do the same on windows 7, but when I tried to install via boot it didn't show the two NTFS partitions SCSI drive.I then tried to install it from windows XP x64 but when I get to choose the drive the C partition I prepared in advance needed an LSI driver. I've downloaded all the drivers I could find for it, but nothing worked.Do I need a special driver for Windows 7 ? if so where can I find it ?
Posted: Friday, January 23, 2009 11:52 AM
View 1 Replies!
View Related
Sometimes Keyboard Not Recognized At Boot Up
When I boot up my system, my keyboard is not recognized sometimes. In the past it would not see my keyboard after being awaken from a sleep state, but that appears to have stopped. I have uninstalled both of my keyboard drivers (HID and PS 2) and switched keyboards! I had to rebot three or four times before it re-installed my PS2 keyboard driver. The PS2 driver is the 2006 32 bit Legacy driver that comes with windows 7. I am running Windows 7 64 bit business edition. I have a MSI X58 Premium Motherboard, I7 920 processor, ATI Radeon 4670 Graphics card, Enermax 500 watt power supply and two SATA hard drives (SSD 64 Gigs C: drive, Western digital 500 gb and a IDE DVD RW). I have tried several different Keyboards, with the same results. Does anyone know what could cause this?
Posted: Friday, January 08, 2010 5:11 AM
View 4 Replies!
View Related
Wifi Adapter Not Recognized
I have a problem with Windows 7 Release Candidate (beta rev7100). I have a Linksys Wireless-B (WUSB11V4) network adapter that I use to connect to my wifi router. It works fine under my Windows XP. However, as I installed Win7 beta, I didn't find any way to make it work. Tried to find a driver, but it does not seems to exist for Win7. Tried to install the driver I got with it, but it doesn't seem to work as it's for Windows XP. Tried to make Win7 recognize it by its own ways, but failed. The adapter's a 802.11b. Is that too old for Windows 7? By the way, when I try to plug it out, I hear a sound and when I plug it in again, I hear another one, but it does not seem to be the "hardware recognized" sound. Can anyone help or send a driver for windows 7?
Posted: Tuesday, May 12, 2009 4:54 PM
View 2 Replies!
View Related
None Of USB Connections Are Recognized
I have just installed Windows 7 32 bit and now none of my USB connections are being recognised. my computer specs are: http://www.acerdirect.co.uk/Acer_Aspire_9301AWSMi_Laptop_LX.AWP0X.008/version.asp Before I installed Windows 7 everything worked fine on XP. I have 3 Maxtor Onetouch 4 external hard drives, a logitech wireless keyboard and mouse. Even my iphone isnt being found when i plug it in. I get no response from windows when I plug the USB's in. I can hear the external hard drives powering up so it isn't a power issue and I have swapped all of the USB connection leads about and it doesn't make any difference. I've tried all of my hard drives on my friends computer and they all work fine. Ive looked through the forums for answers but cannot seem to find any that work. I have been to the disk manager and device manager and they cant find the USB connections. Ive also been to the Maxtor/Seagate website and non of their walk through seem to work or be applicable to this scenario. Any help that you could give me would be greatly appreciated as I'm a student and really need to access these external hard drives along with my i-Phone etc (preferably on my own PC).
Posted: Tuesday, November 03, 2009 6:22 PM
View 6 Replies!
View Related
SATA Drive Not Recognized
I attempted to install win 7 RC to my secondary drive.,which is SATA. After loading the drivers from FLOPPY, i was able to install the files onto the drive. After 1st reboot, the machine went into an endless look rebooting. I am assuming that after that reboot, it lost the drivers for the sata drive. my primary drive is IDE. The only way I got to install 7 was empty a partition on my ide drive. This OS does not look ready for prime time, not even a little.
Posted: Wednesday, May 06, 2009 5:04 PM
View 3 Replies!
View Related
Maxtor One Touch Not Recognized
Maxtor Onetouch II external drive. The drive works perfectly w/Window XP, but is not recognized at all by Windows 7 64 bit. It does show up in the Device Manager and in Disk Management, but I can't initialize it. At first gave me an error message when tried to initialize, now it's turned grey and I can't even try to perform the action. Tried powering the drive, shutting down and restarting, etc. I do get a chime when I connect the USB. Works fine w/XP, so I'm sure the problem is not the drive itself.
Posted: Tuesday, October 27, 2009 1:19 AM
View 8 Replies!
View Related
HP LaserJet 1010 Not Recognized
My HP LaserJet 1010 (USB-printer) is not automatically recognized by Windows 7 (64-bit). I am unable to install the printer manually. I did locate a Vista 64-bit driver for this printer on the HP-website, but I don't understand how I could use the inf-file. I can't find a way to tell Win7 where to look...
Posted: Sunday, June 28, 2009 12:27 PM
View 9 Replies!
View Related
DVD Not Recognized Sporadically
I just installed Windows 7 on a Dell Studio 1737, and have problems with my DVD/CD RW. When I first put a CD or DVD in, the drive is recognized. After a short while, the DVD disappears and there is an error as if the device does not exist. I have tried the fix for removing registry entries "HKEY_LOCAL_MACHINESYSTEMCurrentControlSetControlClass{4D36E965-E325-11CE-BFC1-08002BE10318}" low and upper filters, but this does not work. I have also tried running the command "bcdedit /set load options DISABLE_INTEGRITY_CHECKS", but this also does not work. I cannot eject the DVD/CD once the drive disappears from explorer until I completely shut down and restart the PC. Any ideas? Please email me at (email removed for privacy) with a fix. I like Windows 7 for the low CPU usage, but actually think I am ready to go back to (gasp !) Vista. I also attempted to use the "FixIt" file on the Microsoft support site, but got an error....
Posted: Wednesday, June 03, 2009 11:44 AM
View 2 Replies!
View Related
Ethernet Card Not Being Recognized
I installed the 7022 x86 version of Windows 7. Everything installed fine and there were driver issues which I anticipated but my Ethernet port is not working on Windows 7 or any other OS for that matter. It�s a very strange situation. After it was not seen I Windows 7 I booted from my 2nd drive which has Vista on it and it was not seen there so I booted from my XP drive and it was not seen on there either..... I have re-downloaded all the drivers for each version of the OS but none are making the NIC discoverable. I have an nVidia 680i SLi & I am using the on board port.
Posted: 02-25-2009
View 9 Replies!
View Related
SDHC Card Not Recognized
We just bought an 8GB SDHC Transcend micro SD card from amazon. I did not realize there were probs. I put it directly into my tower in the card slot and nothing pops up. If I put my regular old 2GB micro SD in the slot, it immediately pops up, but not the SDHC card. Is there a fix for this? Something I can download to make it recognized or did I waste my money and get a piece of junk? Please help. This was actually my son's money; he wanted this, and I did not realize there was an issue with these until I googled the prob and had tons of people's complaints pop up.
Posted: 08-15-2009
View 8 Replies!
View Related
Problem:Partition Not Recognized
The Partition, where I have Windows Vista on, is not recognized by Windows 7. Is there any trick to solve this. I can access the partition through booting into Vista but not in 7. My Harddrive is 1TB Western Digital, partitioned into 800 GB for Windows 7 and 200GB for Vista. The 200GB aren't recognized.
Posted: Tuesday, January 13, 2009 8:59 PM
View 2 Replies!
View Related
Product Key Not Recognized
i have downloaded couple of times Windows 7 from Micrsoft website and used my live id to get a a PRODUCT KEY .... and every time i tried to enter the product key for windows 7 i get this error the product key you have entered does not appear to be a valid windows 7 product key .
Posted: Tuesday, August 04, 2009 9:41 AM
View 3 Replies!
View Related
Samsung Monitor Driver
I've had an ongoing problem with this for some time now. You can see here that my Device Manager tells me that I'm missing a video controller, and also in that post is my inability to watch full screen videos online. Here, I talk about the problems I've had with my display driver crashing. Now, yesterday I downloaded Photoshop, and as it opened, a window popped up saying that my "monitor Profile" is defective and needs to be calibrated (See first attachment). If I choose to Ignore Profile, I can use Photoshop as usual, but everything I export has an irremovable yellow tinge. If I choose to Use Anyway, there is no white in Photoshop's color pallet, only the same yellowish color. This got me thinking for the first time that my monitor was the cause of my problems, so I searched online for Samsung 2243swx drivers. On their webpage, they had up for download only one driver, which is for a VGA graphics card (See second attachment). I've been running a PCI graphics card (NVIDIA GeForce 8400 GS), and I was wondering if this could be the problem. Would you say I ought to buy a VGA graphics card?
Posted: 11-28-2009
View 9 Replies!
View Related
Samsung USB Driver
i have a samsung Tocco mobile phone and samsung don't have any windows 7 friendly drivers for it. does anyone know if there is a 3rd party driver i can use to get it working with the samsung studio?
Posted: 10-24-2009
View 3 Replies!
View Related
Samsung 275t Drivers
My current monitor driver default by Windows 7 is generic pnp monitor. with this i cant get my refresh rates higher. i downloaded the samsung drivers from their site, but when running the file i get "cannot open monitor driver, please check the monitor driver or cd" ive tried runnning it in compatibility mode as well. im on x64
Posted: 05-02-2009
View 4 Replies!
View Related
Samsung R60 Drivers
I was wondering if Samsung have released drivers for the R60 laptop that are fully functional in Windows 7, when I installed Windows 7 I had to search for all of the drivers myself, I was given a disk with the laptop but it only works in Vista. When running a benchmark test, the graphics were much better in Vista because I dont think I can find the right driver for the graphics card in Windows 7. Also, a lot of the Fn buttons dont work anymore, for example changing the brightness, turning off the display, showing the battery level on screen, etc. I assume this is done through the chipset driver which I never had to install or even looked for. Also, one last thing, with my graphics card on Vista I get a little ATI icon in the notification area, along with the Catalyst Control Centre, although I never get this in Windows 7.
Posted: 11-15-2009
View 1 Replies!
View Related
Samsung I760 Drivers
I have install the drivers for (Samsung i760) but I think, that they are only for XP, Vista, I get not massage from computer as to if drivers are OK or not (they show in "Divice Manager" I open Windows Mobile Center and my phone said is not conected. Any sugestions as to how to?
Posted: Wednesday, January 28, 2009 12:16 AM
View 7 Replies!
View Related
Cannot Sync Samsung Omnia
have tried almost all the things in most forums concerning this topic. Of hundreds of attempts my device has synchronize twice or thrice in Vista. It does not even recognize the device when connected. Recently upgraded to Win 7 RC. Same problem in Win 7. Tried deleting the partnership, uninstalling and reinstalling WMDC. No difference. The last I tried - unistalled the drivers for the device and tried to connect it to have it reinstalled. The drivers do not load successfully.
Posted: Thursday, August 06, 2009 5:10 AM
View 3 Replies!
View Related
|
TRACKER
