So I installed windows 8 on my HP DV6t-7000 and it regularly gave me BSOD until eventually it stopped booting all together. I have tried doing a fresh install of both win8 and Windows 7 but both provide me with the error that "No drives were found. Click load driver to provide a mass storage for installation". I have run the computer through partition wizard and formatted the hard drive to NTSC but the installation disks still wont recognize the drive, nor will Ubuntu for that matter.
my laptop hdd died a few days ago and I've been pulling my hair out trying to install Windows 7 on a brand new HDD i bought.I don't know where else to look for the appropriate drivers. Seagate does not provide any and there are no other drivers on the HP website.I managed to flash the BIOS with a new version just before my old HDD crashed (it was on the fritz so I managed to back up my data on a USB)
- I've also tried the Clean Installation Guide posted here, no difference.
- I've tried formatting it in Disk Management, still no detection.
I've looked at many forum topics here and it points to an SATA non-detection issue?or could it be that I"m installing Windows 7 Ultimate on a VISTA machine and it's not accepting it? I bought this new hdd thinking I could just put it in and install with no fuss but 4+ days later it's a giant headache and I can't return the hdd if I wanted to. There's a pin (primary slave) on the Seagate that was not on the original, but there are no jumper pins, could this be the problem?
I have a pretty basic desktop computer (CQ5600Y) that broke down on me recently. I haven't owned it for more than a year. All I know is that I left my computer on for a few hours and when I come back to use it, it was responding very, very slowly. It took 5 minutes just for an icon on my desktop to highlight after I clicked it just once. As a result, I shut my computer off by holding the power button and then turned it back on.
When I turned it back on, it will show the Compaq start-up screen with the option for Setup, Boot Menu or System Recovery. I can get to Setup and Boot Menu, but not System Recovery. If I press nothing during this time, the computer will just turn into a black screen with a blinking cursor and the statement, "Disk Boot Failure, Insert System Disk and Press Enter". I have a Windows 7 installation disk and the system recovery disks, but neither seem to work.
When I use the Windows 7 installation disk, I choose the Windows Setup mode. It then goes to a "Windows is loading files..." screen and I assume it is loading files from the disc. It then asks me which language, time and currency format and keyboard or input method I would prefer. I choose accordingly and press "Next. I then choose "Install Now.." It states that "Setup is starting...". I then get through the licensing information and press "Next" and then I choose Custom so that I can install a new copy of windows.
This next step is where I am stuck. A window pops up with the title "Where do you want to install Windows?" It also states that "No drives were found. Click Load Driver to provide a mass storage driver for installation." I don't know where to go from here. I assume I need to load a driver, but what driver am I supposed to load? When I click "Load Driver" it asks me to "insert the installation media containing the driver files."
I have inserted the recovery disks (there are 4 of them + one supplemental disc) and searched through them, but I couldn't find anything. What exactly am I looking for? All these file names are foreign to me. Am I looking in the wrong discs? Are there drivers I am supposed to download from some website? If so, what should I type into google in order to find the right drivers?
Just completed my first build. I have two error messages during the boot sequence that I cannot resolve. The first screen shot during boot is the Asus logo. Next is a black screen that reads: "JMicron Technologies, PCI Express to SATA Host Controller ROM V1.07.23Detecting drives; Done; No drives found"next up is another black screen that reads:[CODE]
My system crashed and i get the blue dead screen. Now i want to install windows 7 (legal) from usb. When i get to the 'where do you want to install windows?' it gives me the following message: No drives were found. Click Load Driver to provide a mass storage driver for installation.I tried to go to my bios and change some things i read from other treads, but it didn't work out for me. I just don't know where in the bios i can change things, maybe my bios is different than others.This is my laptop: MSI GX700 Intel Core 2 Duo T7500-processor @ 2,2 GHz This is what my BIOS tells me:
MAIN Market name: GX700 Model Name: MS-1719x Primary IDE Master [hard disk] Secondary IDE Master [ATAPI CDROM] System Information
I have a netbook ASUS Eee PC 1005PXD.After only two days of use, i get a black screen at the beginning: "Reboot and select proper boot device or insert boot media in selected boot device and press a key".Pressing F9 on boot doesn't work and i'm still getting the black screen.F2 is working, then in Boot Settings, i set Removable Device as 1st Boot Device. (and there is no Boot Booster option to disable).Then, using the Windows 7 USB/DVD Download Tool, i create a Windows 7 bootable USB, in order to use the System Recovery.When i get to the System Recovery Options screen, no Operating System appear in the list. (It say to load drivers in this case, but i have no idea which drivers and how to load them).
Then i press next without choosing OS, but pressing Startup Repair after that didn't help.Also using the Command Prompt didn't help (bootrec /fixmbr, bootrec /fixboot, bootrec /scanos, bootrec /rebuildbcd) The two last commands (/scanos and /rebuildbcd) give: "Number of windows installed: 0".Then i decided to reformat and reinstall Windows 7 (my netbook is new):i boot using the Windows 7 bootable USB i created before, then on first screen i press on "Install now".When i get to screen "Which type of installation do you want", i choose Custom.Then i get to screen "Where do you want to install Windows?" but the list is empty, and at the bottom, it is written "No drives were found. Click Load Driver to provide a mass storage driver for installation".
Its my own fault, I was doing this in a daze. Having installed the new SSD and gone into Windows 7 setup, I thought id created a new partition on the drive for Windows to go on. Anyways, Windows was saying there was some sort of problem, so I thought, ok , rinse & repeat - and so I hit delete...Now nothing is showing up in the drive list. It is visible in bios - and I've since used the OCZ boot disk and did a secure wipe. Still nothing. So I used a PartitionWizard boot disc, and created a brand new NTFS system partition. Still nothing. Do I need some drivers or something? Setup does say I could use a disk to find some...
i've got 2 extra 1TB Seagate drive:[URL]I use these to make backups of my 3 hard drives (1 x SSD, 1 hybrid, and 1 SATA). I brought this new machine back in April, and it was working fine up until then. However, after trying to install some software (which didn't wanna install in the end anyway, due to it being rubbish!), I can now no longer see these drives on my PC The weird part too - is that my Win7 laptop has exactly the same issue ... but my brothers Vista laptop, and Win7 PC see them just fine!To start with I was thinking the drive had gone faulty (as it wasn't working on both my machines), but after testing it on my brothers stuff it prooved they are both working fine The USB's I'm using to connect it to are fine (They work for USB sticks and other USB kit) ... so I'm at a bit of a loss as to what it could be? The even weirder thing - is that my brothers 500gb external drive (can't remember what make that was, but its not Seagate) works just fine!Its driving me up the wall as I can't do my daily backups (I'm a software developer, so having a current backup of my PC incase of a fatal mess up with my system is vital for me)
No drives were found.click Load Drivers to provide a MASS STORAGE DRIVER FOR INSTALLATION.Ok im helping a friend with their computer but have run into a brick wall where can i find a mass storage driver for a hp pavilion dv6-2150us Serial:cnfo146518Product: wa779ua#abarying to install windows 7 home premium 32bitut i get the following during setup No drives were found.click Load Drivers to provide a MASS STORAGE DRIVER FOR INSTALLATION
I'm trying to install windows 7 32bit from a "family pack" upgrade disk (home premium) that I bought like a few hours ago. The disk definitely isn't scratched or dirty.I have a similar problem, that is, when I get to the part where I am supposed to find the drive to install it on (in this case my /C drive) it shows nothing (the list of drives is empty).I bought this computer used and it has a non genuine version of windows 7 (32bit professional)(so I know the computer is able to run windows 7) but I have been having some troubles with that (randomly restarting) so I decided to install a genuine copy of windows 7.
Well, unfortunately I have a serious problem. To go ahead and get this over with.I'm not sure what kind of drives they are..GParted failed to boot [ "BootMGR is missing"] Anyway to figure this out?I'm installing via USB, due to me not currently having the disc.The USB is bootable 100%.
My problem is that Windows 7 does not recognize any of my drives. Nor do I know what kind of drivers to get.Before I tried booting with the USB, it told me that a OS was not found.
Suddenly I cannot open my DVD drives. I get an error message that says cant find the path or you do not have permission. I have googled the problem and tried various fixes to no avail. They are shown as working ok in device manager.
I have had my system up and running with Windows 7 for at least four or five months. I have four drives in an mATX case. Yesterday, while it was idle, I saw it flash a BSOD and then rebooted. when it restated it displayed the following Error: "No active partition found. Reboot your computer." Which I did several times to no avail. Next, I used the install disk to try to "repair" the partition...seven or ten times, no luck. Also, no drives were listed in the window at repair prompt. So, I pulled all the cables on all the drives but the one containing the system and voilas! here I am writing to you without issue and without three of my drives. I have two other sata drives in addition to my system sata drive. one IDE drive on the system.
I plan on reformatting Windows 7 x64 due to some hardware issues. Basically, I would like to be able to have things like Windows 7 settings, themes, ect imported. Any tips on how to do this? I do have separate partitions/harddrives to backup files, program data, ect.
So I will be doing a new install of win7 pro x64 on my newly built rig. My questions should i go ahead and do the install and then install SP1 or install, get updates and wait until SP1 is pushed.I have a disk with the full SP1.
I'm just wondering how to do a fresh install of windows 7, as it keeps freezing lately, ive tried system restore but keeps coming up that it hasn't done it...so id rather re-install from scratch again so ive got nothing on my system...Any help would be appreciated
I am getting an SSD drive & going to be doing a fresh install of Windows 7. While I understand the process of configuring your system for usage of the drive (unplug the other drives so the SSD is only one connected while installing, turning off prefetch, etc).The part I'm confused with is how to move the users folder so it defaults to the "D" drive. I get I can "Move" the folder, Add the "Location" or do the "robocopy" method & create a junction.
FInally got an SSD! Now I just need to install it onto an SSD.. could someone give me an explanation on that? My motherboard is the Asrock Z77 Extreme 4. I am currently running Windows 8 (I will update 7 to this later on down again) on a regular hard drive (slow 5400 RPM Samsung HD)
I've just made a new fresh install of Windows 7 - 64bits (legal version). Everything was fine, all drivers were up to date.But, when I install updates from Windows Update, during the installation of the SP1 (when the screen is "do not turn off the computer"), the computer reboots, and it said that it occurs a BSOD !? I've seen nothing. According to Whocrashed, it's because of BAD_POOL_HEADER, from ntoskrnl.exe (which belongs to Nvidia I think) and e1c62x64.sys (for Intel LAN)... After reboot, Windows continues slowly its updates like everything was OK... but I wonder is that SP1 & updates have been compromised (poorly done, half or what) 'cause of this BSOD? Should I reformat the computer?Windows Update indicates that all these updates were successful...
I wiped it clean from issues of locking up. I have done 3 fresh installs of Windows 7 Ultimate 64 bit retail using all up to date drivers and everything, I have tried with CPU overclocked and normal clock. When I boot up she runs fine and then when I start listening to music off of my backup drive or browse the internet she will lock up at random, and by lock up I mean it is like im looking at a picture of my screen frozen with no responsiveness whatsoever not even the mouse moving no HDD activity ... nothing! So Ive installed the OS 3 TIMES fresh install new partitions format etc. It does it every time after I let windows update do its thing or just listen to music off the backup drive.pecs are:Windows 7 Ultimate x64 RetailBiostar A780XA2-03 Socket AM2+ MotherboardAMD Athlon 64 X2 3800 CPU4GB Ram - I have swapped sticks that I have had - ( 4 1gb sticks 533mhz)
This PC has ran fine since 2008 when it was built. It was recently updated to Windows 7 Pro OEM. During the OS upgrade it had more memory added (4x2GB, all slots filled). Upgrade and install went flawlessly. All software (photoshop, premiere, firefox, antivirus) was re-installed without any errors or hick-ups. Upon updating firefox (I believe the timing was co-incidence) it Blue Screened. It has had issues ever since. So my last stitch effort was to back everything up and re-install Windows and hope that it fixed the problem. Needless to say that it hasn't been fixed and it still randomly blue screens. Windows Memory Diagnostic ran with no errors returned
Bought a new computer 2 weeks ago, came in 3 days ago. Been having trouble with it since. Usually I'm the "Mr. Fix-it" when it comes to PC's but I've never messed around with any debugging tools.
I've tried all the troubleshooting you can possibly do when trying to diagnose a blue screen of death. Tried both RAM sticks separately, took the video card out and used on-board video. I even tried both RAM sticks with on-board video separately. Unplugged the DVD-ROM, no avail. I called ASRock and got a technician who I could barely understand, but was telling me something about "XMP". I didn't see the XMP option under the DRAM configuration, even if my sticks don't support it wouldn't the option still be there? I think he has my motherboard confused with another one. He told me to either replace the RAM with new RAM or send the motherboard back in and exchange it.
I came here to see what the BSoD DMP files REALLY have to say the problem is, so I can solve it once and for all. I didn't pay for new hardware to let it sit here and collect dust.
SPECS: Nothing is OC'd except the GPU, it was OC'd straight from the factory
Ive ran memtest86 4.0a and i found several million errors. So i scanned through 1 and 1 ramslot to try to determine which ram was giving the errors, this only resulted in 1 of my 4 ram had only 1 error? I found this weird so i thought it might be the DIMM thats corrupted.
So now i removed 3 of my rams and i only run with 1 which passed the test. Still i get unexpected shutdowns aka BSOD.
Ive tried to remove my SSD and only use my HDD back and forth , changing to IDE inside BIOS, but with no good results at all.. Ive also tried to change my PSU to a different brand, but all volts seems ok. I also reinstalled windows with USB, CD, from HDD yeah you name it, different versions... etc.. i even tried to install Windows 8 but with the same result
This all actually just started out of the blue, i have no clue how but i didnt install anything , all of the sudden i started having connection problems which resulted in BSOD.
They used to have more of a 'restore disk' but lately I haven't been seeing that anymore. What are users left to do when you need to do a fresh install of Windows? If its for someone else, could I use my windows install disc and use their product key (sticker on bottom)? I've heard that it doesn't always work that way? Does Microsoft have any official documentation about this and if possible, could you share your experiences?
I'm putting together a HTPC using a ASUS E35M1-I Deluxe (AMD Zacate mobo/cpu combo), 30GB Kingston SSD, and 4Gb Crucial DDR3 1066.Problem is when I boot from the Windows install disk I get the "Windows is Loading Files" status bar but when it gets the end it just hangs there. Usually it boots right into the next Windows loading screen. So before I start troubleshooting I want to make sure there's nothing special I need to do with the SSD before installing Windows. Its a brand new drive but I'm pretty certain during the installation process there's a Format option. The Windows install disk was burned from an ISO using IMG Burn at 16x. Before I left for work I started another burn (with img verification) at 8x. But I'm not certain that will help. I've burned plenty of images at 16x speeds without issue.
A few days ago, all out of the blue, my PC started to freeze - at that time with VISTA installed. I tried to restart and it froze again, just after a couple of minutes. Tried again, again, again and again. With the same result. Without getting any further I tried to install Windows 7 to get my PC up and running again. Formatted all of partitions to get a fresh and clean start. and it froze again, within a couple of minutes. Now I suspect it may be caused by a hardware problem? What is there to do? What can I do? I`m far from a PC-expert, I HP is somewhere between 1-3 years old I think, and I`ve never encountered this problem before, on this PC or any other.
I installed Windows 7 Home Premium over Vista Business on a PC to see if it would run and tested it out for a few days. I used my installation CD that was good for only one PC. So to activate Win 7 on that 2nd PC I need to buy another copy of the OS. Can I just reinstall over the current version of Windows 7, or so I need to wipe the drive and install fresh?
Is there any way to do a fresh install without a disk that my key is for? I have a pc with no backup copies of Windows 7 Pro OA that came on it. I only have a Windows 7 Home Prem disk that I bought for my laptop. Is there anyway to make it work? Will my Pro OA key from the site of the box work with the Home Prem disk I have? Or is there somewhere at Microsoft that I can download a copy of Pro OA that I have paid for?
I have never purchased a laptop before, only built my own systems at home. Before I make my purchase, I have a couple of questions.
Do most laptops come with an OEM Windows 7 disc? I'd like to be able to do a fresh install and wipe all of the junk that will inevitably be pre-installed on the laptop. I've even heard of junk software that is somehow intertwined with the Windows installation that forces the user to update drivers, etc. only through the software itself; sometimes it doesn't even allow the latest drivers. I'd like to avoid all of this and work with the barest possible system and build it up myself.
If Windows 7 discs sometimes do not come, I'm assuming that I will have a valid OEM serial that is tied to a plain copy of Windows 7 (that is, not riddled with laptop software). Would I be able to download a copy off of Microsoft's site and input that serial when I'm prompted?
