i have a problem that i m not able to boot from my DVD RW it plays cd and DVDs but i want to install new window that doesnt boot i changed my windows DVDs all are bootable but not able to boot it ever dsnt show pree anykey for boot where and what is the problem ?
View 1 Replies
I have a Dell Inspiron 1545 Laptop with Windows 7. Laptop will not boot up. I tried Last Known Good Configuration and Safe Mode, it will still not boot up. It looks like it will but it does not. Then I went to the BIOS and did the Hardware Scan and it gave me this message.Error Code 0142Msg Error Code 2000-0142Msg Hard Drive 0 - self test unsuccessful Status 79
View 3 Replies View Relatedi want to boot my dell laptop to change my windows 8 os.but i cant do it
View 2 Replies View RelatedWhen I power on my Dell 1545, it goes to the Windows Error Recovery screen. Choosing LAUNCH STARTUP REPAIR results in a screen that says Windows files are loading, then goes to a blank screen where it hangs. Choosing START WINDOWS NORMALLY results in the process hanging at the STARTING WINDOWS screen.
Attempting to boot the computer in Safe Mode results in the process hanging at \Windows\system32\DRIVERS\CLASSPNP.SYS
I was able to remove the SATA hard drive, hook it to my desktop and recover all my files. Attempt to boot from the Windows 7 Installation CD results in the process hanging at the STARTING WINDOWS screen.
Attempt to boot from the Windows 7 Installation CD with the hard drive removed results in the process hanging at the STARTING WINDOWS screen. I was able to boot Ubuntu from the CD and navigate through the computer.
I'm at a loss as to what to do next. I am able to access the BIOS setup, but can't make any changes because the touchpad will not move the pointer. A USB mouse will allow the pointer to move, but not when I'm in the BIOS setup.
my computer wont boot ,its says ,BOOTMGR image is corrupt.the system cannot boot what do i do to boot or repair this
View 1 Replies View RelatedI'm working my sister's Dell Inspiron n5010 running Windows 7 Enterprise. It has been fine until this week when it became slow to the point of unusable. I had installed Microsoft Security Essentials on it for her, and she said one night when she shut it down, it installed updates. It finished and shut down. Next morning, she opened the lid and the screen was on saying "installing update 1 of 12, 0%" as if it had never finished and froze up from the night before. It finally finished and when it booted into Windows, I tried to run a virus scan, but it said Security Essentials was out of date and failed to start. I tried unsuccessfully to update it, and I couldn't get much of anything else to run either, it was so slow. I used my install disc to start fresh with a new install of Windows, and it seemed to fix it, until I got to installing drivers. before beginning on the drivers, I installed Security Essentials and MalwareBytes, ran scans, and they came up clean. As soon as I started installing drivers, though, it became slow, froze up, and I was back to square one. Now when it tries to boot to Windows, it gives two options: launch startup repair (which freezes) or start Windows normally (which also freezes). Booting from the install disc to start again with a Windows install won't even work now. As soon as it boots from the cd, it freezes.
View 6 Replies View RelatedI'm working on my brother's girlfriend's Dell Inspiron 1764 that will begin to start windows and then immediately goes back to the post screen. I have tried to do a system restore, and recover from a system image... but of course she has made neither of these backups. The laptop will not load windows in safe mode and i have also tried to disable driver signature enforcement. I'm not exactly sure what happened before the failure, but i know my brother installed a Honda data logging program called HONDATA right before it crashed so I am suspecting some sort of driver issues. Is there anything else i can do besides the full Dell system restore that would wipe all of her data?
View 1 Replies View RelatedDell Vostro 1510 Laptop upgraded from vista to win 7 and win 7 only worked one time. Goes from windows starting to black screen. The cursor shows on screen. Will not boot from Windows 7 disk. Opening in safe mode results in black screen.
View 3 Replies View Related1. I want to open the boot options in my dell laptop but when dell logo appears i press f12 as it is written there then nothing happens i want to change the boot settings. I also tried delete button but nothing happens. and even setup which opens by pressing f2 also not working..please help guys.
2. As per Windows 7 upgrade assistant guide i have lastly insert DVD of Upgrade assistant to upgrade drivers and other things but when i click on next then it freezes and giving Microsoft .NET Frame Unhandled Exception. What is this problem? I want to upgrade my drivers from CD but it is giving error.So please help me out guys.
3. This problem is related to 2 point that as i wrote that i am unable to upgrade drivers so i tried to find out drivers for Windows 7 32 bit on Dell site.But when i saw Dell site have drivers for only Windows 7 64bit.. So now what can i do? I can't install drivers and because of driver problems laptop is not working properly and i can't download drivers for Studio 1555 for windows 7 32 bit from site because it is not available.
Cant boot from my OEM Windows7 DVD because it fails along the way with 0x80070017 error.Downloaded 4.36GB Windows 7 ISO from Digital River and used ISOBuster and ISOBurner several times each to burn a bootable DVD. The computer boots straight into Windows, never giving the "press any key to boot from DVD" message.They all have the same 3 files in the root as the bootable OEM DVD: autorun.inf, bootmgr and setup.exe.With the exact same 3 files, why dont the ones I burned boot the machine?
View 8 Replies View Relatedtoshiba satellite c650 250gig hard drive 4gig ram
View 4 Replies View RelatedMy DVD ROM is causing problems and frequently not working. I am currently using Windows 7 32 bit. I would like to perform a clean reinstallation of Windows 7 on my PC. I have the Windows 7 DVD.
I know about creating a bootable USB or a bootable DVD. But I dont want to format my USB drive to make it a bootable USB device. My Questions are--
1. Instead are there any ways to boot from a file in a USB flash drive, without formatting and making a bootable USB device?
2. I would also like to learn about the basics of high level formatting. I searched google and have read articles at kioskea and howstuffworks, but none has exclusive easy articles on How Formatting Works and How to Format any Disks (including USB drives).
I have 3 laptops, was trying to boot from linux distro 32 bit on all of them. The oldest toshiba laptop is a 32 bit and the bootable dvd works! My 2 newer Asus laptops 64bit cant boot the dvd. All of their boot orders have also been configured. Asus even has a BBS option that can let me boot into dvd drive directly. On 1 Asus I only get a blank screen. On the other, no medium detected, cdrom boot priority indicated "boot ready".
View 7 Replies View RelatedI have two HD drives, one SATA and one IDE, plus one SATA CD/DVD drive. Firstly I used to have XP on the SATA and Windows 7 on the IDE, but the IDE drive is smaller and slower and I wanted to essentially swap them over. The boot devices are set in the bios as CD/DVD first, SATA second, IDE third.
So I have installed XP first on the IDE and now Windows 7 on the SATA, but after I removed the Windows 7 DVD and restarted it is refusing to boot saying NO BOOT DEVICE DETECTED, INSERT SYSTEM DISK. Now if I place the Windows 7 dvd in the drive and ignore the PRESS ANY KEY TO BOOT FROM CD/DVD...., it will book fine.
This will surely fustrate non-technical users no end and some may not even think to try and replace the OS disk and try again. I think I know what has happened, but more importantly how do I go and fix it to just boot without needing a damn boot disk everytime!?
the hard drive failed... i like to install an external hard drive. I have inserted the recovery CD...removed the failed hard drive yet the error stops to recover
View 1 Replies View RelatedI have Windows 7 on a AMD Phenom Machine. Hard Drive died so I put another one in and restored Windows with Acronis True Image.
When I leave the Windows repair disk in the drive, the restored system starts perfectly, runs perfectly etc. But if I pull that repair disk out of the drive I get this error about "No Bootable Device" "Insert Disc". So in other words that repair disk has to be in the drive, else I get the error.
I have already:
1. Verified that the boot sequence points to my Windows Drive
2. Run system repair. That's useless. It just tells me everything is fine.
3. Run bootrec fixmbr, vixboot, rebuildbcd. No problems found
4. Run Chkdsk. No problems found.
I have a Compaq Presario C700 which is giving me the following error: No bootable device -- insert boot disk and press any key.
I'm a technical user and have been able to fix just about anything, until now. I've done some research, and I've found that this Compaq C700 is a terrible computer that just can't be fixed. They're probably right.
I've tried to boot off an external optical drive, but this failed to load the system. I've checked the boot order is correct and that the optical drive was enabled in the BIOS, but this still did not allow me to boot from the optical drive. I knew that it recognized a system there because it had an underscore, which meant it was trying to boot from the disk, but sadly, no luck.
As for the hard drive, I've replaced it with a spare, couldn't install Windows 7 on it directly from the laptop, so I installed it on my desktop system, then put it back in. Still, the message. No bootable device -- insert boot disk and press any key.
I've verified every available BIOS setting to the last detail. The only thing I could think of and haven't yet tried is to try to see if there's a CMOS battery anywhere and disconnect that, but I'm not sure where that could be on a laptop, and taking this thing apart is practically impossible.
I know the CPU and system board and everything else seems to be in working order, it's just that it can't seem to work off of a Windows 7 disc or installation. A red flag for me was when I went into the BIOS (InsydeH20) it mentioned that Vista was the factory installed OS. I wonder if it's doing this because it's expecting, and is proprietary to, Vista.
no detected usb cd rom+pen driver
View 1 Replies View RelatedI was just on the laptop browsing the internet as normal then all of a sudden out of nowhere it shuts off. Turn it on again.
I get this screen: [URL].
Then I got to the BIOS: [URL]
Then checked bootable devices: [URL]
The HDD is still connected: [URL]
So what do I do? I have valuable files and photos on this hard drive and do not wish to reformat or reinstall my OS.
How to full format my laptop hard drive. I have already Re install windows 7 in E: drive. Previously I have win-7 in C: drive after encounter some problems, Re-install new Windows 7 but that time I didn't format the hard disk that's why its install in drive E. Now when start the up of the lap top both selection are coming will start with old win or new win-7...and having some trouble with my windows 7 that's why I want to full format the hard dive without bootable disk and install new win-7.
View 2 Replies View RelatedIs there a way to make a bootable recovery windows XP CD from a laptop running windows 7?
View 1 Replies View RelatedLaptop(Dell core i3 vista. Laptop freezes to start?
View 1 Replies View Relatedhow to work dell laptop both vga in laptop and projector
View 2 Replies View Relatedwhenever I turn on the laptop, it seems to boot into Windows 7, in that the "Starting Windows" text appears and the little animation of colors forming the logo shows, but as some point it fails. This message appears on screen:autocheck not found - skipping AUTOCHECK After a few seconds a BSOD shows up, but too fast for me to make out what it says. It used to, but after some hasty fix attempts no longer does, cycle around to a menu that informed me of this error:Status: 0xc000000f Info: The boot selection failed because a required device is inaccessible. Here's the longer history:As some point in the past I decided to try out dual-booting Windows 7 and Linux on the laptop. I got it to a state where this worked fine. I had partitions roughly as follows:[Ubuntu][Windows 7]([Data and files][Boot]) The parentheses denote a logical partition. The Boot partition was very small and only held what was necessary to launch GRUB. This week, I realized that I hardly ever used the Linux partition and decided to get rid of it to reclaim storage space. This is where the trouble begins. I rebooted into a thumb drive that could run GParted and modified the hard drive layout in the following steps: Delete the Ubuntu partition Delete the Boot partition Grow the Data/Files partition to take up the space left by Boot Shrink the Windows 7 partition to make it faster to move Move the Windows 7 partition to the front of the volume Expand it to take up the remaining space. What I ended up with was: [Windows 7]([Data and files]) My naive and fatal mistake was to trust that the Windows Repair CD could fix any boot issues, and also that there would be no catastrophic hardware failures. Both of these assumptions turned out to be false.
First, the laptop's CD/DVD drive has either broken or is too unreliable to use. I have noticed it becoming more and more unstable over time, but now (when I need it most!) it simply does not seem to want to spin up and function at all. This forced me to create a Windows Repair USB drive. However, I can't load any installation media. This is because the laptop did not come with an install DVD. It had a recovery sector, which I cannibalized for the Linux partition. I did copy the stock recovery stuff to a series of DVDs, but, well...This is all to say that any solution that requires a DVD drive is straight out until I can replace it, which I'd like to consider a last resort.My expectations for the Windows Repair CD/USB have been dashed. Attempting to automatically fix boot issues either fails for some specific reason (I can probably reproduce it and provide the details, if necessary), with a dialog to send a report, or fails because it cannot detect any problems. I have tried a variety of things based on my own research to fix this through the command prompt: Running chkdsk /x /r on all drives. Does not find any errors. Running various bootrec commands: /fixmbr, /fixboot, /rebuildbcd, /scanos. All complete successfully, but the last 2 report finding 0 Windows installations. Using bcdboot and bootsect to recreate the bootloader. Again, no errors result, but it does not fix the issue. I guess it should have been obvious that none of the boot record fixes would matter, since the laptop does boot into Windows 7, briefly.
Today when I was surfing on my laptop (G74S Series) I wanted to restart the laptop because the internet crashed and it usually helps to restart. But I restarted it holding down the power button thing.So, I restarted it and while I was waiting, staring in to the screen, the blinking "_" thing when you start up was doing that for a while and nothing was happening, and a couple of seconds later the computer tells me that it can't boot the laptop/pc because no drive was found. I saw an error code but I didn't catch it, but it was something like "0x0000".So then on later, it sent me in to "Image Restore" But I have no image to restore with, so I cancel it, and then it sends me into the menu where. I can choose to "Restore Computer" or "Scan for startup errors" or something like that (I don't really have a such accurate memory.)And on the top it also says "os unknown on (unknown) local disk".Everytime I start the computer it sends me to that menu where I can choose to restore my computer etc..And I can't really do much about it since I don't have the windows 7 disc/dvd thing either.And this all came all so sudden I don't really know what to do.I don't have any backu or anything, and windows can only detect my /D: drive and not /C:, and I have my OS on /C/
View 2 Replies View RelatedMy Dell 15R will not boot up, it just beeps when I turn it on
View 2 Replies View RelatedI've try to set up another hard drive with no good result now I'm trying to boot up but stops,the message is:checpoint [Bye] is a DELL xps will not go with f2-f12 -f8 I keep trying but none responds just the message
View 1 Replies View RelatedI have a Dell Inspiron 1440 running windows 7. This computer was purchased new about a year and a half ago, and I have had no problems up until a couple days ago. I went to turn my laptop on the other morning and as usual the dell logo came up and loaded, then the windows symbol saying "starting windows"... then strangely a black screen with a cursor arrow... nothing more, no log in screen... just black nothingness... I have ran the diognostics and they all say "pass". I am able to access F2 & F12 but it will not boot in safe mode or with a command prompt.
View 3 Replies View RelatedA diagnostic says boot manager is missing or corrupt....error code 0x15. No operating system shows up in system recovery options window.
View 14 Replies View RelatedI have very recently installed Windows 7 7100 64bit with little success. I can use the M1330 for about 20 minutes and then bam..... the lappy will turn off and when I try to turn it back on I get nothing but a weird white screen. Not even the dell boot screen will appear.
When I first installed Windows 7 it found all drivers but due to this issue I have sought to change a few key drivers. Such as, the nVidia 8400 drivers and I have updated the SATA drivers to R154198
My specs are:
- 4 GB of RAM
- 2.4 CPU
- 200GB HD; 7200RPM
- nVidia 8400 Video card
I have heavily searched the net with no joy. please help.
i just restored to a disk image i recently backed up. When it was done i tried to boot my system and it automatically booted to the dell diagnostics. why is that? i can't seem to find a way to boot to my system.
View 3 Replies View Related
