Hard Drive Failure After Fresh Install

Sep 4, 2009

I have just bought a brand new hard drive due to my last ones controller failed.

Western Digital Caviar Black 500gb

So the problem,

Did a fresh install of win 7 (Build 7229) two nights ago, all installed perfectly, next day (yesterday) went to boot up pc and had the dos error message - Disk boot failure, please insert system disk and press enter.

My first impression was it may have been an install failure, so i formatted the hard drive and reinstalled. shutdown the PC and rebooted up and i had the same error message, now after this, i got my failed hard drive out and after a lot of faffing around, BIOS found it and it gave me the same error message.

Can anyone tell me what the problem might be. I have tried Windows startup repair, did not fix.

BIOS settings are

First boot device is Hard drive

second boot device is CD-ROM

(I have even swapped these around to boot from windows 7 and it just starts the setup procedure of installing windows drivers) I have even set boot order of HDDs so my main windows HDD is up top. Anyone got any clues.

View 9 Replies


ADVERTISEMENT

Cannot See Partition After Fresh Install On Windows 7 On New Hard Drive

Nov 10, 2012

I just reinstalled Windows 7 on a new hard drive and during the installation process, I split the disk into two equal partitions of 500gb. In 'My Computer' I can only see one partition which is the C drive but not the other partition. Looking in Disk Management, the other partition seems to be labelled as 'Unallocated'. How can I allocate this into a usable D drive? I would have expected this to happen automatically during the installation process.

View 1 Replies View Related

Fresh Install Of Windows On Primary Hard Drive

Jul 21, 2012

I bought a new 2 Tb hard drive because my primary one was getting full. I would like to do a fresh install on the primary drive once I have moved over all the games, videos, pictures, etc. that I don't want to lose. I can format the primary drive and reinstall windows without affecting the content on the second drive, correct? Is there anything I need to know?

View 7 Replies View Related

BSOD On A New Hard Drive, Fresh Install Of Windows 7 Ultimate X64?

Jun 21, 2012

I've just installed a new hard drive and a fresh copy of Windows 7 Ultimate x64 on it, and I just received two BSODs within minutes of each other, citing ntoskrnl.exe withSYSTEM_SERVICE_EXCEPTION on BlueScreenView. I had periodical blue screens before my last HDD died so it's most likely something else causing it, maybe hardware... but not sure how to tell what. I've attached the necessary files.- the original installed OS on the system? Yes- Full retail version- What is the age of system (hardware)? About 5 years- What is the age of OS installation (have you re-installed the OS?) Two days

View 3 Replies View Related

Fresh Windows 7 Install On SSD And Will Not Detect New Seagate Hard Drive

Nov 17, 2011

I've had a sudden loss of my hard drive space. I've deleted alot of stuff, like over 20GB, more then just a few times and it just disappeared in less then 2 days. I've read some topics here with the about same problem and tried what they sugested there: to use software like WinDirStat, TreeSize Free and SpaceSniffer. But they just won't show me my whole hard drive. The stop at 50% and show it as if they have scan the whole 100%.

View 3 Replies View Related

Fresh Windows 7 Install Will Not Detect New Seagate Hard Drive

Feb 20, 2012

Me and my fiance just finished putting together her first real gaming computer and we wanted to use a Patriot 64g SSD to put win 7 on and use a 1TB Seagate drive for all the rest of the storage. The installation of Win 7 onto the SSD went nice and smooth but when we get into windows it is not detecting the 1TB HD at all. Funny thing is that when I go in to the SSD properties, I can see the Seagate under the sharing options. The only info I have found is how to clone off an existing hard drive with Win 7 on it not how to do a fresh install on 2 new drives.

View 1 Replies View Related

Moving Hard Drive To New Motherboard Without Fresh Windows 7 Install

Apr 4, 2012

I am doing a motherboard upgrade for a friend. I need to know how I can move his hard drive with his current OS instal to the new motherboard without having to do a fresh Windows 7 install. He has too much that cannot be replaced. Is there a way to do this?

View 2 Replies View Related

Fresh Install Failure On New System SSD

Aug 30, 2011

Here's the problem, when I boot up my genuine Windows 7 Ultimate DVD, and I get to the select partition screen and select one, it gives me the following error : Windows could not format a partition on disk 0. The error occured while preparing the partition selected for installation. Error code: 0x80070057

I've tried what they outlined in this thread, [URL] When I get to formatting the drive in Command Prompt it just stalls at 0% and says diskpart has encountered an error; the parameter is incorrect. see the system event long for more information.

I've tried changing SATA to IDE instead of AHCI in bios.

I've tried using a recovery disk for my Acer 3830tg, but it just stalls at 0%. I've tried using a genuine Vista Ultimate DVD, but it doesn't even detect a disk drive. It's a Corsair Force Series 90GB SSD F90 in an Acer 3830tg-6412 with 8GB of RAM.

Oh the SSD works fine, I was able to boot it up and run everything fine prior to trying to do a fresh install, which in hindsight is stupid

View 12 Replies View Related

Possible Hard Drive Failure?

Feb 21, 2011

I had assisting my cousin get his laptop running. He actually went and got a WD backup drive. He has been running good. Has a tendency to overdue the AV scans, Malware Scans and CCleaner Scans. Anyway, he booted yesterday and a timed to start on "Boot Normally" with safe mode and safe mode with network etc: screen came up. He advised he got logged on and ran everything for anything with no luck. Every time he reboots ( 2-3 times ) it came up as described. I had him do a chkdsk. When it finished it booted normally and has several times since. Since this is the condition the computer was in prior to me helping him a month ago, I thought as a minor leaguer, that I'd inquire with the forum members. Is it possible his toshiba laptop which originally ran Vista, he got it dumped for Windows 7 Home Premium, has the 160 GB Hard drive beginning to croak.

View 2 Replies View Related

My Hard Drive Failure

Oct 3, 2012

A few months ago I made the mistake of buying a used hard drive off Ebay. Last night it died on me and at the moment its in the freezer because Ive heard that freezing the drive can get it up and running long enough to get data recovered.

View 9 Replies View Related

WD Hard Drive Failure Or Motherboard

Mar 8, 2009

I was wondering if you could provide me with some feedback on a hard drive issue that started when I booted up my pc yesterday. Hard Drive is WD 160GB SATA.

I received this error at boot up:

Read Disk Error CTRL+ALT+DEL to restart

I restarted and luckily I was able to get to the desktop (took longer then normal tho).

Checked Event Viewer.. nothing showed. Checked Performance Logs... no errors showed.

Decided to double check all the connections... all plugged in nice and secure. Rebooted. Got the Read Disk Error again. this time it took me 3x to get to desktop. I decided to try another SATA connection on motherboard. REbooted.... got error again.

I ran a chkdsk/r and when system rebooted the Read Disk error showed up again.

After another 3 ctrl+alt+del reboots... I was able to get into Windows. I downloaded the Diagnostic Tools from WD and my drive failed both the Quick and Extended Tests. Not surprising lol

Anyhoo, here is a screenshot of my WD Diagnostic test results. I was wondering if it was a HDD issue or a motherboard issue? Any thoughts? I would rather replace a HDD then a motherboard. This WD 160 SATA drive is less then a month old also. BIOS sees the hard drive.also tried setting BIOS back to default.... sometimes that works but not this time.

View 9 Replies View Related

Hard Drive Failure And Lost Files?

Nov 23, 2011

It occured when i tried to open internet explorer while google chrome was downloading a file. However, I have always been able to do this when I attempted it previously, so I am not sure what made this time different, but after i clicked on internet explorer, everything i had open got immediately closed, my screen flashed black, and when it was back at my desktop, all my icons were gone aside from Recycling bin, Microsoft Word, and Powerpoint, and like 50 little message windows opened one after the other saying that files may have been lost because of damage done to the C drive. I cannot preform a system restore because it says there are no previous restore points, and all of my files (documents, pictures, downloads, music, programs) are no longer on my computer for some reason? Is this just a problem with my C drive that can be fixed and restored? Or are all of my files gone for good? Also, my PCtools Spy Doctor ran a scan and said: Adware.BHO.GEN (20 Infections) - High Threat.

View 11 Replies View Related

Hard Drive Seek Failure / Does Not Boot

Apr 30, 2012

I've got a Dell desktop that will not boot, gives the message Drive 0 Seek Failure.I was able to boot to a linux disk and copy files, so the drive is spinning. I ran the built in Dell hard drive diagnostics, the hard drive passed. I also ran the Hitachi Drive Fitness test, and it passed.I assume maybe it just needs some repair to the boot sector?

View 9 Replies View Related

Hard Drive Failure Windows 7 Won't Bootup

Mar 21, 2011

Can't access any files. Need it urgently as it has all my uni stuff and need it to submit before deadline.

View 9 Replies View Related

XP Hard Drive In Windows 7 X64 Machine Failure?

Dec 9, 2011

My Xp machine won't boot. So I moved the HD into my Windows 7 machine. The drive shows up in WExplorer but it won't show directories or files.

View 3 Replies View Related

Just Re-installed Windows 7 After A Hard Drive Failure

Jan 27, 2013

Just re-installed Windows 7 after a hard drive failure. Windows 7 x64 Home premium . 2.4 Ghz Processor 4GB RAM . Cannot Install SP1.

View 2 Replies View Related

Hard Drive Failure After Virus Now Can't Access

Jan 21, 2011

i had a virus and used norton to clean out and laptop went to blue screen and then started norton recovery, since then i cannot access the hard drive in the laptop or via a caddy. just says unable to load driver..

View 16 Replies View Related

Deleted Files From Other Hard Disk In Recycle Bin Is Lost After Install Fresh Windows 7

May 19, 2012

Yesterday, I just reinstall fresh windows 7. After I install the OS, I just realize that my recycle bin is empty. Before I installed windows 7, some of my deleted files on my other hard disk is there. But now, I could not find it anymore. After that, I tried to select show hidden folder, files, and drives and unsellect hide protected operating system files on folder options. I try to browse to one of my hard disk, which has the deleted files on recycle bin before, then I found it the recycle bin icon there as well (For instance, the path of the drive is: N:$RECYCLE.BIN). I tried to look at the properties, and I found that the missing size of the deleted files was on there. The problem is I cannot access it. When I tried to open the recycle bin, it just empty. I need some help with this. How do I retrieve the files again to the OS recycle bin, not the hard disk recycle bin? Is it possible to access it again? I really need those files back.

View 8 Replies View Related

Windows 7 System Recovery - Hard Drive Failure

Jun 18, 2012

I just turned on my laptop on and it wouldnt go past the "starting windows" logo. So I restarted my computer and it gave me an option to repair start up option and once the repair finished it said it has failed to solve the issue and it pop up a Windows System Recovery which is always good if I wanted to restore it to the factory state unfortunately I have about 30 GB more or less data on this laptop that is basically my life and wanted to retrieve the data.

It also gave me an option for command prompt so i went and run "chkdsk" it got to 49% and from there it kept on listing the entries on the disk and numbers that its got errors on, I didn't quiet finished the disk check and turned my laptop off. Reason being it was 4 AM in the morning. I have been using my laptop for over 2-3 years and by use I mean it has been online almost 80% of the time more or less.

Is it hard drive failure? If so is there a way I could retrieve any data from it? I know there are software that you can boot from CD or USB to salvage what ever data is left or readable, however the data is somewhat precious to me and dont want to do further damage. I would have gone to an professional and gave it to them but I can't afford it. I'm going to change the hard drive into a different laptop to check if its truely an hard drive problem related.

View 14 Replies View Related

1TB WD USB Hard Drive Failure / Is In Device Manager Not Initialized

Oct 6, 2011

I was normally using my computer, when I suddenly noticed one of my hard drives disappeared from My Computer. Checked the Device Manager, I get the following. Trying to initialize it throws up this error: Seems to spin just fine. Trying different USB ports failed, switching cables as well. Already tried a few programs. GetDataBack for NTFS throws up error 1117. R-Studio also fails, as does DMDE and MTY. My friend even borrowed me Microsoft DaRT (part of MDOP), but when I boot into it, it doesn't recognize the HDD at all, no matter how hard I try. Only my Windows 7 installation does.Anything I can do in this situation? I had a lot of important data on it, and it's not completely dead yet. Maybe I can still save it somehow, without haivng to pay one of those data recovery thieves...

View 9 Replies View Related

RAID5 Setup Failure - One Hard Drive Failed

Jun 16, 2012

I have raid 5 setup, on a ASUS P5K WS motherboard using matrix storage manager. Just copied everything on to it, now a hard drive has failed. I got new hard drive but its seen as none Raid and raid showing as failure ?

View 3 Replies View Related

Oem Install Fresh Sata Drive

Nov 26, 2009

I am attempting to install a Windows 7 OEM x64 onto an older machine I have. MB is a Foxconn NF4UK8AA-8EKRS, CPU is AMD Athlon 64 x2, 4200+ 2.25 GHz, RAM 1GB. I installed a new OEM 500GB SATA hard drive unformatted.

Current OS is Windows XP Home SP2, I deleted SP3 since it was giving me some problems with auto login.

My DVD drive will not read the Windows 7 installation disk, similar to another post the drive just flashes, never spools up. It will read other CDs and DVDs.

I initialized the hard drive but have not partitioned or formatted the new SATA hard drive which is where I want to install the new OS. While the BIOS recognizes the drive, its not listed on Computer tree.

I have copied the Windows 7 OEM DVD contents onto a Folder that I created on a Toshiba External USB drive. Only had a 2GB USB Flash Drive so thought I would use the external drive and select the setup.exe in the Windows 7 files I copied into a folder without formatting a complete 250GB ext USB drive.

Question, can I partition and format the new SATA drive using the Windows XP Home Edition with an NTSF format and will this be recognized by Windows 7?

Question, can I install Windows 7 from the Toshiba Ext USB drive's folder onto the newly formatted SATA drive? Or does Windows 7 require a different formatting setup?

The BIOS and MB won't recognize a DVD drive it only allows a boot from CD. I removed the CD and DVD master/slave parallel cable and only installed the DVD as the master, but Windows 7 DVD just blinks and never spins the drive.

If I can get the new OS installed I'll remove my two older 40GB PATA hard drives and add more RAM. This machine is for my wife's use since it was in the garage gathering dust. Thought I would revive it and set up a wireless home group between my machine and her's. I added an all in one printer/copier/scanner in addition to the HP Photosmart D7460 I have so we can share files, printers and Internet connection.

I have been building my own machines since about 1990. Building a machine is fun (takes maybe 2hrs) but all the software kicks my butt. Also I went to the OEM System Builder License at Microsoft OEM Partner Center that is the most confusing arrangement I have ever seen. I'm just a home builder having fun, not a business, must I buy the full version to get this installed?

View 1 Replies View Related

Windows 7 Won't Install On Fresh Drive

Feb 1, 2013

Got a virus in my old drive. I bought a new drive and tried to install Windows 7 on it and slave the old drive so to pull files off I wanted, and then format the drive. This did not work. All I get is the Windows blue screen with the dove on it, and no desktop.

View 3 Replies View Related

Hard Drive Failure On Preloaded HP Laptop - How To Obtain Copy Of Os

Mar 18, 2012

I have a HP Pavilion dv6 laptop and getting alerts saying the hard drive is failing. I've pushed all my data up to NAS storage and will install a new hard disk but... How can I get a replacement of Windows 7 Home Premium. With the drive failing, Windows is becoming unstable and I need to do a fresh install on the new drive once it's installed.

View 9 Replies View Related

Windows 7 Hard Drive Failure - Only Boots In Safe Mode?

Jul 31, 2012

After trying to scan my computer with tdskiller (I believe its called) to remove some viruses, I was asked to reboot. When I did, my backround desktop picture turned black, files seemed to be missing from my desktop and a window poped up scanning and telling me how many errors I had. Shortly after I got about 20 error pop up messages. I rebooted my computer and more files were missing to the point all I had was recycle bin, and two other programs.

Now the computer runs only in safe mode, No matter what I do (pressing f8 - start in normal mode) nothing works. I cant get internet access, and worst of all, I cant even system restore or even recover it back to to the malfunctioners option due to errors. I am stuck and do not know what else to try.

Ive tried the repair option in dos aswell and it just keeps me in the "Loading window files" screen, as I left it there for nearly four hours im guessing that was not going to work.

View 7 Replies View Related

Windows.old File On C Drive After Fresh Install On New SSD?

Apr 12, 2012

I just built my first computer, and it has an SSD and an HDD. I installed a fresh copy of Windows 7 on the brand new SSD, and on the C Drive I'm seeing a windows.old file that is 11.5GB, and there is a windows file that is 12.3GB. I don't get this at all. Like I said, it is my first computer.....everything seemed to go well with the build, and sp far things are working, but I know this isn't right. This was a brand new drive, like I said, I do remember when it was going through the different parts of the install, and restarting several times, that it seemed like it was staarting at the beginning again.....as If when it had finished, I didn't take the DVD out, and was basically starting the install "again"....if that makes sense, I stopped it, and pulled the DVD and it booted up, and seems o.k.

View 3 Replies View Related

Fresh Windows Install, Old Program Drive

Aug 2, 2012

i'm looking to do a fresh install of Win 7 (mostly just to reorganize my HDD setup) and here's the catch - I have a secondary drive with all my games, program files, data, etc. and I'm wondering if there's an easy way to get the new Windows install to recognize these applications without having to reinstall them all. I know I could go into the registry and change keys, but that would probably take longer than reinstalling them all.

View 4 Replies View Related

Hard Drive Failure While Making USB Bootable Windows 7 - DRMK Error

Aug 28, 2012

My system is Dell Inspiron 17R SE (7720), 1 TB Hard Disk 5400 rpm + 32 GB mSATA, 8 GB RAM, 3rd Gen i7. I was trying to make a bootable USB flash drive for windows 7 from Windows 7 Home Premium Reinstall disk that came with my Dell laptop, using the WinToFlash utility. But in starting the process, the PC froze, all applications (even explorer.exe) stopped, and Alt+Ctrl+Del refused to work. I turned the laptop off and back on, where it refused to even show the OS list and showed a DRMK message instead with a command prompt C:> as:

Loading DRMK V8.00...
DRMK Version 8.00
COMMAND.COM Build 37 - Jul 28, 2008
DRMK KERNEL Build 15 - Aug 8, 2008
Copyright (c) 2006-2008 Dell Inc. All rights reserved.
C:>

I tried booting from Windows 7 reinstall DVD but none of the repair options worked. I tried reinstall and repair options but my Hard Drive did not show up. It rather asked to Load Drivers for the Hard Disk. However, it did show any of the USB drives I connected to it, along with an X: drive, which must be the recovery drive for Dell's factory restore. I tried looking for Hard Disk drivers in that but no luck.

Then I downloaded from another PC a USB utility for Seagate Hard Drives from Dell website that makes a bootable USB. I ran that utility and it showed all the test passed (But there was no firmware update during the tests). Another thing I tried was using list disk command on command prompt in Windows Repair, but It did not show any drives, not even the X: drive. It only showed the USB drives I attached to it, or the DVD drive in list volume command.

I cannot boot to windows, I cannot install new windows, I cannot repair the windows and I cannot even factory restore my laptop. The hard drive shows up in BIOS, but not in Windows Boot or Windows Installation. Is there any way I can get my Hard Disk back without losing data? I have two partitions of that drive. I don't care about formatting C: Drive (Windows) but I wanna preserve E: Drive (the one filled with personal data but no programs).

View 2 Replies View Related

Windows Won't Boot After Drive Format And Fresh Install

Jul 2, 2012

I just formatted my C-Drive and installed a fresh copy of windows 7 ultimate on it. After restart, I got the following screen - See image attached. Now Windows can't boot at all. I tried using a system repair disk but it doesn't work. I doubt if it is a hardware problem, since I can access the boot menu and its options, but as I said, running the repair disk fails, I keep on getting that screen when it restarts.

View 4 Replies View Related

Windows 7 Fresh Install Using Pendrive - DVD Drive Not Working

Mar 1, 2012

I was thinking of doing a fresh install of Windows 7 64bit Ultimate. Currently I am running the same. but wanted to do a fresh install. The problem is that My DVD drive is not working.. and I took it out. Need steps in installing windows 7 64bit Ultimate using USB pen drive. I want to wipe out the entire hard disk before doing that and want to do the fresh install. One of my friends when tried to do like this, his bootable USB pen drive was not detecting via BIOS.

View 5 Replies View Related

After Getting Rid Of Windows 7 Hard Drive Failure Virus The Start Menu Programs Are Empty?

Nov 21, 2011

After getting rid of windows 7 hard drive failure virus my start menu programs are empty.

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved