I am using an original version of the windows 7. And recently ( I really don't know what happened) my PC won't start normally. It also says that windows Start-up repair can't fix the problem. What should I do ( I don't want to reformat cause I lost my windows 7 installer ).
View 6 RepliesSo ive been getting the black screen with movable cursor lately and have tried many a methods to remove it i tried checking in my event log for something, and this is waht it said "The following boot-start or system-start driver(s) failed to load:dtsoftbus01" So what does this mean and how can i fix this?
View 4 Replies View RelatedMonday couldn't boot up PC, had to go to system recovery and restore to previous day.
Log files show below that 4 things failed to load. Tuesday couldn't boot up PC again.. tried to restart like 4-5 times.. Finally comes up and in the logs there's numerous things that failed to load. Running a sfc /scannow right now.
I found corrupted system files, but it appears that the hard disk is fine. executed chkdsk and no bad sectors.Just looked into this on event viewer-The following boot-start or system-start driver(s) failed to load:xsoaynmfmfxpefxbozedltnzvijcvI am running Acer Aspire X3950-U3022 with Windows 7 Home Premium Home Edition.
View 4 Replies View RelatedI'm not sure where to even begin to fix these problems. Some online searches suggested doing a system repair but I want to get some more feedback here before proceeding.Here is the message from the event log:The following boot-start or system-start driver(s) failed to load:
AFD
cmdGuard
cmdHlp
CSC
DfsC
discache
ElbyCDIO
[code]...
I realized some of these are not Windows 7 related but most are. While the computer "works", I do experience frequent reboots and freezes. Perhaps some of these driver loading failures are part of the cause of my issues.
I purchased a copy of Windows 7 Home Premium a while ago and installed it. I kept Windows XP on the pc and had the option at start up of which operating system I would like at start up. Everything was running fine for quite some time until about 2 weeks ago. The system started to "freeze"....unable to do anything! The hard disk light was now showing as constantly on. The only thing to do was turn it off and restart. It didn't matter whether I was using windows 7 or XP.Eventually I decided to do a clean re-install of Windows 7. The installation kept "freezing" at various points and eventually installed after about 5 attempts. I have installed NO programs, internet, peripherals or anything, so the systems is just "as is" after a clean reinstall but the system STILL freezes after various amounts of time....sometimes 5 minutes...sometimes as long as 30 minutes.I am only playing the in-build solitaire or Freecell to "test" how long till it freezes! Usually now tho the hard drive light is not constantly on when it freezes! Does anybody have any idea how to resolve this. I (foolishly!) thought that doing a clean install would sort everything as the hard drive is formatted at the beginning of the installation.I took a print out of the system details and installed programs (eventually!) using Belarc Advisor before reinstalling.
View 9 Replies View RelatedUsing the Windows 7 DVD that came with the machine I went through the repair Windows procedure 3 times. The first time it searched for restore points of which there are none because the machine has Rollback Rx installed instead. It then restarted with no change. I went through the same process but this time it said it had repaired Windows however; restarting gave me the same missing OS message. On the 3rd attempt it displayed the restored OS as being on D:. I ran the diagnostic tool and it said no errors were found. Restarting gave the same error.
View 6 Replies View RelatedHow to Change Time to Display Operating Systems at Boot in Windows 7 ?
View 0 Replies View Relatedbeen searching all over the internet on an alterative machine for a solution to a problem that occurred about an hour ago.To offer background on the machine:I upgraded it last summer with a 60gb Solid State HD to host the OS and a 700gb HD to host the bulk non-system essential files and appsI've had no anti-virus on it but occasionally run the Microsoft free Scan & Repair along with Iobits cleanup suiteThere's been this Win7.CH Trojan Horse that is occasionally detected for the past 6 months and even though I select to fix and repair, it always comes backThe machine will occasionally crash after exiting a high performance application like a videogameAfter installing the Planetside2 videogame Beta on the 700gb drive, my SS drive began to become strangely over-stuffed with files, and I could not narrow down where they originated. I uninstalled a few unessential Iobit programs and cleared my downloads and recycle bin, then something even stranger happened. The SS drive had 16gb free, while this entire time I've had it I've only managed to keep it about 2-4gb free, and the file clogging stopped from what I could tell.Anyway, a week or so later, after exiting the Planetside2 Beta application earlier the machine crashed (unsurprisingly) but upon startup, did not recover.
Startup repair unsurprisingly can't fix it, and I receive the following problem signature:The Windows Repair Problem Signature Problem Event Name: Startup Repair Offline Problem Signature 1: 6.1.7600.16385 Problem Signature 2: 6.1.7600.16385 Problem Signature 3: Unknown Problem Signature 4: 21200506 Problem Signature 5: AutoFailover Problem Signature 6: 17 Problem Signature 7: CorruptFile OS Version: 6.1.7600.2.0.0.256.1 Locale ID: 1033decided to give the posted solution a go since it seemed so similar to mine.Unfortunately I did not realize that the tech tailored the solution specifically to the posters scan results, so when I tried to use the same solution, it didn't work.I'm quickly realizing that my problem is not the same...What I've tried so farI ran Chkdsk and it said F parameters aren't specified and it only took a millisecond to complete showing nothing wrong.The Startup Repair scan returns are all "0x0" errors.The afformentioned forum posts solution didn't work since it wasn't specified to my machine
I have a Samsung netbook (n145) which has had a few issues starting up over the past couple months - it would prompt to run chkdsk before booting, I would let it run, and it would boot. However, yesterday I got the 'windows failed to start - a recent hardware change may be responsible' error message, and giving the option to try starting windows normally (which fails: there is a flash of BSOD and then screen goes black, and computer restarts, arriving at same 'failed to start' error). The other option is to run system repair, which also does not work: it takes ages to bring up a dialog box that searches for errors, but I have let this run for hours and it remains stuck. Tapping f4 to bring up samsung recovery also results in a stuck screen. Tapping f8 to boot to safe mode does not work either.
My main concern is having a working computer, and I can't really afford costly repairs or a new netbook. I got this one used about 1 1/2 years ago and it has no cd drive/OS boot disk (windows 7 starter came already installed). What should I do? Can I fix the hard drive, or should I replace? I am not at all technically skilled and have limited knowledge but an endless capacity to learn. I called samsung and they suggested I replace the hard drive to the tune of $100-$300 for parts alone, which is too expensive for a $100 netbook.
Okay, so this just happened out of nowhere. Nothing seems to have led up to this -- the system booted and shut down successfully, and no software updates or installs were done during the period of time it was on when it was last working. I've attempted many things, but none seem to work. /ScanOs reports no OS detected, while startup repair said the OS was booted successfully. bcdedit also shows no directories linked to "unknown". CHKDSK reports no bad sectors, so such can be discarded. This happens every time I attempt to boot to Windows 7 (Home Edition, x64). I have a copy of Fedora 17 set to dualboot with it
View 14 Replies View Relatedi just crashed som1 64 bit lennovo laptop while i opperate a 32 bit pc dont have any windows system with me,it wont start on safe mode,and system repair has failed many times.the laptop was running on low battry and it shut itself,when i tryed to reboot it,it automaticly went to system repair which failed
View 2 Replies View RelatedRan F12 to regain Operating system - long version. Says computer passes everything but there's no operating system found. Did this Twice. Tried "Operating System" CD that came w/ Studio 17 laptop. Hit option to run via CD & never got anywhere after an hour. Tried Reinstall Hardware disk that came w/ laptop. It shows Vista, but laptop came w/ Windows 7. See where it shows the system's checking things out, but never get anywhere.
View 7 Replies View RelatedLast night I was on my computer and then I shut it down. Today when I came home from work it keeps saying windows failed to start. I tried hitting f8 and loading to the last good configuration doesn't work, safe mode same thing, repairing nothing, so my last resort was my windows 7 cd. So I went into bios and made my configuration boot from cd/dvd popped it in and restarted, a black screen came up saying windows is loading files, then the windows 7 menu came up, picked my language, next, and first I tried repair my computer, I get the little circle meaning its loading for like 5 seconds them it does nothing, rebooted again but this time I chose, install and I've been on the setup is starting for like 20 min. And forgot to mention, when it boots seem like it does good then comes to the screen where it says windows failed and gives me two options repair our start normal, if I pick repair it just reboots and start normal takes me to like the pick your user screen but its just blank no users, so I can't even restore our access the computer.
View 3 Replies View RelatedSuddenly my Win 7 Home Premium x64 will not boot. The system starts, POSTs then loads the DVD driver, then the screen goes black (not blank but "lit up" black if that makes sense). Then nothing. If I use Hiren's boot cd I can boot up using the "boot from HDD" option fine and Windows operates normally. System restore to a previous configuration made no difference to the original problem. I cannot boot into Safe Mode. F8 just offers me boot order options.
- Running the Windows 7 DVD I find: "No operating system is listed on the Repair Windows option."
- Running Startup Repair finds the following error: "the partition table does not have a valid system partition" which it claims to have repaired, but the error remains and Windows will still not boot.
I followed this advice:
Boot 7 dvd to system recovery options command prompt. Type: Diskpart
list vol (find the vol letter e.g C or partition number e.g. 1 for the system partition )
Sel vol C ( or sel vol 1, obviously use the correct letter or number)
act exi
My system partition was easily identified and listed as healthy so I selected it and made it active. The problem still remains exactly the same. My system is self built just over a year ago, to my knowledge has been running fine, without any hardware issues. I'm prepared to do a clean install if that's what it takes but if there is a way to fix the partition problem without that I'd like to explore it first.
"Missing operating system" massage is coming when i start my system and i am not able to start. I think because , i had given "mark partition as active" option for one hard dive (E) in disk management when last time i opened. it did not have any data. i did not know, this will make any problem. Now i am not able to boot windows re installation dvd also. i can only take BIOS settings.
View 6 Replies View Related"Missing operating system" massage is coming when i start my system. I think because, i had given "mark partition as active" option for one hard dive (E) in disk management when last time i opened. it did not have any data. i did not know, this will make any problem. Now i am not able to boot windows re installation dvd also. i can only take BIOS settings.
View 2 Replies View RelatedI am looking to upgrade my desktop from an xp to 7. System builders are very cheap which concerns me. What is the difference from a system builder and the regular version.
View 4 Replies View Relatedwhenever i boot my pc i starts making sounds for like 15 secs and later asks me t choose my operating. this started wheni removed my battery for like 3 weeks and then inserted it back. am using acer mini.
View 5 Replies View RelatedLiving is south FL can be a bitch when the rains come as there often is a ton of accompanying lightening that plays havoc with the electrical system, even though I have surge protectors inside and outside the house. We just had some very heavy rains with lightening and my computer shut down several times, but I could restart it each time...except for the last time when Windows wouldn't startup. At that point, Start Up Repair came into play. Although I routinely backup on an external drive, of course I never did it this month-DUH!Results from SUR were error free (error code=0x0) on all the parameters tested, however there were the following error codes reported:"Unspecified change to the system configuration might have caused the problem." Failed: 0x1fRepair Action: System FilesFailed: x490There were more options to select for a recovery task, but I didn't try them as they didn't seem to be as salient as the two above.
View 6 Replies View RelatedA few days ago, I started having trouble with Dell Latitued D800, Windows 7. First, Windows would not boot up. I was able to boot windows using the F12 option. When Windows loaded, the screen display had shrunk and was centered with a black perimeter. I contacted the guy that sold me the computer and he suggested that I check the boot sequence for the boot issue. That worked fine. To resolve the resolution issue, I was advised to select the "last known good configuration" from the F8 options. After I did that, the Windows Error Recovery Screen. A Recent Hardware Or Software Change May Be The Cause. I attempt to start windows normally.
View 7 Replies View RelatedWhen I last shut down my HP Mini 110 netbook it began installing updates, which is normal now and again.When I switched it on the next day it comes up with a black screen saying Windows Boot Manager:Windows failed to start. A recent hardware or software change might be the cause... It goes on to tell me to insert my windows installation disc but netbooks dont have diskdrives
View 2 Replies View RelatedWhen I last shut down my HP Mini 110 netbook it began installing updates, which is normal now and again.When I switched it on the next day it comes up with a black screen saying Windows Boot Manager:Windows failed to start. A recent hardware or software change might be the cause... It goes on to tell me to insert my windows installation disc but netbooks dont have diskdrives!Also says The boot selection failed because a required device is inaccessible.
View 1 Replies View RelatedI have had problems booting up my Toshiba laptop. (Windows 7 Ultimate 32 Bit) When i would start my computer, Windows failed to start. A recent hardware or software change might be the cause. To fix the problem:1. Insert you Windows installation disc and restart your computer.2. Choose your language settings, and then click "Next.3. Click "Repair your computer." If you do not have this disc, contact your system administrator or computer manufacturer for assistance.File: BootBCD Status: 0xc000000e Info: An error occured while attempting to read the boot configuration data. tried to solve the problem using repaire methods such as :At the DOS prompt type the following three commands:bootrec.exe /fixmbrbootrec.exe /fixboot (may return an 'Eliment not found' message)bootrec.exe /RebuildBcdI also deleted the BCD parition or it's related to it which is 100Mb in size ,
View 8 Replies View RelatedI left my 160 GB hard disc unused for 1 month.It was installed with Windows 7 ultimate.But now it says unable to start windows. I have another 1 TB hd. i can boot from this and my 160 GB still works as a memory storage. Its only problem is that it is unable to boot.I think if i install a new copy of window it will work.but i need to know why it was happened when 160 GB hard disc was not in used for a long time and any other way to recover it.
View 3 Replies View RelatedI'd had some problem with my laptop the last few days, what I believed to have happened is my laptop (Dell inspiron n5110) which is windows 7, was doing a configuration, but because of my bad connection, my internet dropped. It was stuck at 15% for 3 hours so I turned it off as it was about to run out of battery. It had some problems loading and starting up but they went after a day. but 1 day later I am booting up and I get a black screen.
View 9 Replies View RelatedI have a serious issue, this all started when i tried to update my bios and had some how screw up my os. I tried startup repair failed system restore failed and safe mode failed also. What should i do now?
View 1 Replies View RelatedI have already re-install the program but,still its not working
View 1 Replies View Related I am starting to get errors on my computer when I try opening any browser. on IE, it turns on for half a second and closes and shows this, It shows a "RunDLL" error, The application has failed to start because its side-by-side configuration is incorrect. Please see the aplpication event log or use the command-line sxstrace.exe tool for more detail.
Chrome is the same error but with the chrome location instead of inetcpl.cpl, same with firefox. What I did before this, everytime I turned on the computer, right after the splash screen when i first turn it on, it power goes off and restarts a few times and then it boots.
A recent hardware or software change might be the cause to fix the problem: 1. Insert Windows installation disc and restart your computer, 2. Choose language settings/NEXT, 3. click repair your computer. If you do not have this disc, contact system admin or computer manufacturer. status OXCOOOOOOf the boot seletion failed "a required device is inaccessible
View 4 Replies View RelatedI went to use the rest room. I come back and he had spilled his juice inside my machine. I lost video and the fan on my brand new 7770 was stuck on max rpm. I turned everything off, took out the gpu, cleaned it, let it dry. Let the rest of the computer dry. I reinstalled the GPU and turned on my machine. The fan was no longer stuck on max RPM, so I felt I dodged a bullet. However, windows failed to start. It continually fails to start. I tried an older GPU (9500 GT). The fan on it would, for some reason, not spin, but I saw the model come up when I started the PC. Windows wont start. Initially I believed my problem was limited to a shorted GPU and I don't mind buying another new one, but since I was unable to get my old GPU to work I'm worried something else has shorted.
View 7 Replies View Related