I have win 7 booting from a 256GB SSD. All data is elsewhere, so there is a lot of room on this drive. Are there any problems with creating a partition on the SSD to install Win 8 on? I have read tutorials on how to set up a dual-boot 7/8 system. They generally state that Win 8 should go onto a separate drive. Wouldn't a separate partition work just as well?
View 4 RepliesI want to dual boot xp and windows 7 on two different partitions. And I want to have an additional partition for programs and one for user documents. Is it possible for the two os's to have the same shared program files directory.reason for this is to save space instead of having different installs for each just have them both run off the same directory.
View 8 Replies View RelatedI have just purchased a new pc that came with Windows 7 Home Premium 64-bit, which wont run my company software, which was made in 1995, 16 bit. This 16bit software ran fine on my previous pc, which had Windows 7 Starter 32-bit. But the 64 bit Windows 7 version wont run it, I cant use Windows XP Mode on my version of Windows 7, need Pro - Ultimate Version.
I want to install and run the Windows 7 32-bit I have, on my new pc (I still have the installation disk) on a separate partition and keep the 64 bit version to. Is this possible to install both 32 bit and 64 bit versions of Windows 7 and then select which to run when the pc boots?
i am dual booting 7 64 bit and ubuntu linux,i was wondering if anyone has any issues with this type of setup or just with partitions in general
View 3 Replies View Relatedi have a new work laptop with xp sp3 on it. I want to install w7 64 bit as a dual boot, but only have 1 physical drive. i cannot remove my current installation as it is pre-build from work, but can partition the drive etc. However on trying to install w7 64 bit I get a message saying cannot install windows 7 on efi drive with mbr, not gpt. Can I do what I want without screwing up my xp installation?
View 5 Replies View Relateddual booting windows 7 home premium x64 with linux fedora 14 on dual independantly dedicated drives. i am a college student with moderate computer (windows) knowledge but am doing software development and would like to play around with some linux for a class. i have no prior experience with linux and have minimal knowledge of operation. i am currently running windows 7 and would like to keep it as my primary os. i do not wish to share media files across drives or os's, windows does that just fine as is and i dont want to get into a third drive. my current drive is a 1tb wd black caviar hdd. it is also currently 2/3rds full and the desktop is about 6 months old so i would rather not partition the drive for a dual boot. i would think that there are some other advantages for the os's operating independantly off their own drives other than if one hdd dies i should still have the other with its os still ok. i have read some topics about RAID configs with dual boot setups with dual drives like this but am not very familiar with RAID. is there a RAID config that would be beneficial in this situation? i currently do not have a RAID card. my tower internals are not very accessible and i dont like the idea of disconnecting drives depending on which os i want to operate.
View 5 Replies View RelatedAs currently configured, XP is on drive C:, Win 7 was added to drive E:, and the system is currently run as a dual boot. Attempting to boot without the XP drive present will yield a "NTLDR is missing" error very early in the boot process.
I have already tried the following:
(1) I moved the hidden Windows Boot Manager files (bootmgr as well as the associated Boot folder) from the XP drive root to the Win 7 drive root.
(2) After physically removing the XP drive, I rebooted to the Win 7 installation DVD, and used the "Repair Your Computer" option to pull up the "Recovery Tools". Then, using the command prompt utility, ...
(3) I attempted to write a new boot sector to the Windows 7 disk using the command: Bootrec /fixboot, - that yields an error though. The Bootrec /fixmbr claimed success, but ultimately did not make Win 7 drive bootable.
I had to reconnect drive C: just to boot into Win 7 again to write this. I do have files backed up, but to format and reinstall files would take many hours beyond just the time to transfer 400 GB of data, since I have dozens of purchased applications that need to be freshly reinstalled and validated as well. Basically I want my E: drive now to be my boot drive while the C: drive is reformatted and used for general storage.
Any idea how to make my Win 7 drive bootable? Do I need a partition program that is more adept at creating a viable boot sector, or is that even the problem?
I've just discovered (after a panicked hour trying to work out what was going wrong) that my boot and system partitions for windows 7 are on different hard drives. The boot partition is on my 120GB SSD and the system partition is on my 320GB WD HDD.
This means that I have to have both hard drives plugged in for my system to boot. Obviously this isn't the best set up as if one of the hard drives fails then I'm screwed! Is there any way to fix this without having to re-install windows?
I have an Acer Aspire 1810TZ with Windows 7 Home Premium 64-bit. The HDD is 160GB.Yesterday I moved (without resizing!) both the 100MB system reserved partition and my 40GB C: partition towards the "beginning" of the HDD for the purpose of creating an unallocated space of some 110GB towards the "end" of the HDD. (The C: partition had previously been shrunk using Win7 disk management and the system worked fine after reboot prior to partition move).llowing the partition move I can however not boot into Windows anymore. Windows boot manager gives the following info:Status: 0xc0000225Info: The boot selection failed because a required device is inaccessibleThe boot manager also suggests I reinstall Windows, but of course the restore and rescue DVDs I burned based on Acer's eRecovery tool does not work.
View 4 Replies View RelatedI have 2 SSDs each partitioned into 80GB and 40GB like this:
-Drive1-80GB (boot) and Drive1-40GB
-Drive2-80GB and Drive2-40GB
Drive1-80GB is already the Windows 7-64 boot partition for the system. Can I configure a software RAID-0 with Drive1-40GB and Drive2-40GB? I know this is unorthodox but I wanted to try this for a few reasons.
It came with 2 primary partitions: a 650 gb C drive (boot) and a 50 gb D drive (recover). Because the windows partition tool didn't let me reduce the partition size by more than 50%, I decided to use EaseUS partition master to do that. I made D drive logical and renamed it to F, made the C drive 200 gb and made a new 400 gb logical drive and named it D. Then I restarted the laptop and let the tool do its work. After this, the problem started. I couldn't get past the bios screen, and couldn't even tap F2 and F8 to get in the boot menu. When I inserted my windows 7 recovery dvd, I heard the dvd drive working, but nothing happened. When I plugged in a usb drive, however, the laptop loaded the cd drive and I could reinstall windows 7 from the cd. Windows works now, actually, even my old windows installation still works, but I still can't boot up without inserting the usb drive first.
View 3 Replies View RelatedI have Win XP 32 bit on my old drive. I buy Win 7 full retail and a new HD. I set bios to boot from cd etc. Win 7 starts up. It shows the 2 drives, so I select new drive...no problems. It starts install. I leave it to do its stuff.When I come back its up and all ok.I dint get any option to boot from XP. The drive was listed as "SYSTEM" but not old Windows or anything.
Also ASUS chipset drivers dont work and they were listed as 7 drivers.I tried Vista drivers but it normally shuts down and restarts. Nothing.
I have a PC with 2 hard drives- the first hard drive has a single partition and windows 7 64-bit is installed on this hard disk.Now I wish to install CentOS 6 on the first partition of the second hard disk.I have created the dvd for installing Cent OS also.How do I configure the boot loader in Windows? If I install Linux on second hard disk, will this overwrite the Windows Boot Loader? How do I create a dual boot system so that the windows boot loader correctly shows linux as an option, so that I am able to load either Windows 7 (existing) or Linux(on second hard disk- not yet installed)
View 2 Replies View RelatedOn my computer I have 3 primary partitions:
1. "System reserve" which contains e.g.the Bootmamanger and MBR
2. First Win 7 installation ("main")
3. Second Win 7 installation ("reserve")
When I boot now at first the Bootmanager on the first primary partition is called/started which in turn starts the boot menu. In the boot menu there are currently two entries:
Windows 7
Windows 7
So I cannot distinguish between the "main" and the "reserve" Win 7 installation. How exactly can I modify/rename the two "Windows 7" entries in boot menu? After selecting and booting the actual Windows 7 installation the other Windows 7 installation is visible as a separate partition in WinExplorer:
C: Running Windows 7
D: DVD drive
E: Other (non-booted) Windows 7
How can I automatically hide the other Windows 7 installation? The drive E: should be available e.g. for USB sticks or network drives.
One of my friends has a windows 7 computer with an account for himself, his mother and his 2 sisters. All the home directorys are stored in drive C. Partition D is shared. The question is, how to get a partition layout like this?
Partition 1: OS + programs
Partition 2: home partition for himself
Partition 3: home partition for his mother
Partition 4: home partition for his sister
Partition 5: home partition for his other sister
Partition 6: shared partition for some photos.
I installed Windows 7 on a partitioned harddrive with vista on the other half. After the installation i have my boot menu with:Windows 7, Windows Vista, Windows vista still works but when i try and load windows 7 i get a boot error message
View 9 Replies View RelatedI have XP (x86) installed on one partition.
Last night I installed Windows 7 (x64) on a separate partition.
Anytime I had tried this in the past, using Vista, it always detected the Windows XP partition, and gave me a boot menu with "Earlier Version of Windows" option to boot to.
This is not so with Windows 7.
How can I get the boot menu to show both options, to boot to XP or to Windows 7?
I have dual boot with Xp and windows 7.when i log into my Xp all the restore points being deleted from windows 7.when i check the disk management information in 7 it shows windows 7 create a logical drive with my Xp primary drive.even i am hide the drive from both windows means Xp drive from windows 7 and vice verse.So i like to unmount or remove the drive partition of windows 7 from Xp and Xp primary from windows 7.So that they dont affect each others system files with being deleted the partitions.
View 1 Replies View RelatedI installed opensuse 12.1 on dual boot along with my other windows 7 installation. Installation of opensuse is successful and i can use it. But when I tried to use windows 7 on grub, it says bootmgr is missing. I've already encountered this problem a long time ago so i tried to use bootrec /fixmbr, bootrec /rebuildbcd and bootrec /fixboot in the recovery console in the windows 7 DVD. Rebuildbcd and fixboot did not work and it said something like it cannot find my windows installation. I also tried bootrec /scanos, it returned a windows installation on D:\Windows but my windows is in drive C. I think this has something to do with me messing up the active partition in disk management a month ago but i already fixed it by setting the active partition to the system reserved partition. Only fixmbr is successful, but now i can't boot on any OS because it says: Missing operating system.I also tried bcdboot C:\Windows but it failed with a message that goes like: Failure when attempting to copy boot information..
View 2 Replies View RelatedI was having win 7 RTM and i tried to installl OSx86 in second hard disk
after few failure i successfully installed OSx86 in my secondary had disk now the problem is that i cant boot win 7
i changed boot order i tried windows 7 disk repair
but both failed
im getting some Boot mldr missing...
Actually even OSx86 is not booting i get OSx86 boot screen with two hard disk to select if i select windows disk it still says the same Boot mldr missing.
I can't get Win 7 to boot after setting up dual boot (Ubuntu 10.10) on my GF's laptop. I'll describe the problem and everything that has been tried so far. REALLY hoping somebody has an idea, I'm getting desperate.I installed Ubuntu last night via the Live CD. Used the Live version to install alongside Windows and partition the drive, install Grub, etc. At reboot, after POST it would just go to a black screen with a flashing cursor. I could only run off the live CD. A forum member determined the Grub was trying to load from the wrong partition. We changed that and voila! Grub now loads properly. I can boot into Ubunto via Grub with zero problems. HOWEVER: when I try to boot into Win 7 from Grub, it just locks at the same flashing cursor of death screen. The 7 partition is till intact, I can see and access all the files on the 7 partition from within Ubuntu, however 7 will not boot. I have tried downloading and burning the Win 7 repair disk and doing all of the following,Running the automatic Start Up Repair - several times. All it does is remove Grub, but booting still goes to the flashing cursor and I have to reinstall Grub again to be able to do anything after POST.I have used the command prompt to run "bootsect /nt60 SYS /mbr". Has the same effect as above.I have used all the bootsec.exe /fixmbr, /fixboot, and /rebuildBCD commands. Again, all have the same effect and I have to reinstall Grub to get anywhere.I don't have an installation disk to try and just do a repair install because Asus apparently doesn't feel that I would need one of these. All I have is the recovery disks from the Asus AIRecovery application that want to just re-format the entire drive and start over. This isn't an option. It's my GF's laptop (mine gave up the ghost last week) and we both have WAY too much highly important data on here. Not to mention she would castrate me . Now from all my research the only other thing I've come across that sounds possible is that the boot flag needs to be set to a different partition. Somebody had a somewhat similar problem and it turned out the way Dell set up the system the boot flag had to be moved to a recovery partition and it worked fine. I'm wondering if Asus has something similar going on, but I can't figure out how to move the boot flag. I'm going on 12 straight hours of working on this now
View 9 Replies View RelatedI setup an XP/Windows 7 dual boot on two drives. Currently C: Windows 7, D:XP
Love Windows 7 and now I'm ready to convert to single boot Windows 7.
I'm not real savy re. bcdedit so will need very detailed instructions
I did find the command line in Windows 7 by going through accessories but I'm scared to go further without help.
Eventually I want to clean up the D:xp and use it for storage etc.
I'm guessing this procedure may have already be written up but I can't seem to find it.
How to Change the OS Name in Windows Boot Manager ?
View 0 Replies View RelatedI recently added a hard drive to my computer (SSD), and installed Windows 7 x64 onto it. The result being a dual boot system, which by default boots to the SSD, and optionally (by Windows Boot Menu), can be booted to the original drive (standard mechanical drive).
Initial setup went fine, however I decided to customize the Windows Boot Menu, so that logical names could be associated with each operating system instance. To do this I used EasyBCD and I altered the names in the Windows Boot Menu from: Quote:
Windows 7
Windows 7
to... Quote:
Windows 7 - SSD
Windows 7 - Standard Drive
Shortly after the modification I noticed that I was no longer able to boot into the original OS. Instead I was being presented with a "Repair Windows" option. Figuring that my EasyBCD "tampering" may have had something to do with the issue I decided to change the names back to "Windows 7" in the Windows Boot Menu. However doing so had no positive impact on boot up of the original OS.
After booting again into the original OS I accepted the "Repair Windows" option, and then left the computer over night to do it's "thing". After completion of the "Repair" the situation has deteriorated -
* Windows doesn't load (the same as before)
* Windows doesn't present a "Repair Windows" option (it did before)
* The computer reboots a short period after the "Starting Windows" screen is presented
As a side note the drive is in good health, and all data on it can be read from within Windows 7 when I boot to the SSD OS.
I have installed a year before UBUNTU on my pc with dual boot (i.e. use either window 7 or ubuntu).the NTFS partition that contains the UBUNTU was corrupted and i wanted to take the dual boot from my PC. I used the instructions from the web site: http://www.makeuseof.com/tag/how-to-...t-environment/but the disk management tool would not let me delete the NTFS partition.Could any one help me delete the NTFS partition and use just windows 7 as the only boot. step by step help would be great.
View 8 Replies View RelatedI got windows 7 running fine for a while now and ever since my XP did not boot anymore.I was not worried to much about it since i did not need it at the time.But now i really REALY need it,See i got all my Cubase projects in there and my cubase plug-ins al setup in XP and i need to get to the projects?At first it did not do anything and using easyBCD did not help either.I cpoied ntldr and detect to the root of C: wich contains my XP and now it shows the bootscreen but hangs on a black screen.The thing is right before the bootscreen shows i see the text" invalid boot.ini" flashing by very quick.I am able to enter that winXP install in safe mode and i tried safe/vga mode as well wich works but thats all.
View 9 Replies View RelatedI have a laptop I bought a year ago on which a created a dual boot Win 7 (32bit)/Win XP SP3 install, each on a separate partition. It was my first Win 7/XP dual boot install, and my first personal system that I allowed to have a Win 7 install on it at all, so although I have plenty of experience working on pretty much every previous version of Windows, I have very little experience with Win 7 and dual boot configs.
Today about 2 hours ago my audio spontaneously stopped worked for no good reason, so after shutting down each program to see if that cured it (which it didn't), I restarted the system. Out of the blue, for the first time I've ever experienced it, I received the msg "MBR Error 1" - Press any key to boot from floppy. I don't have a floppy of course on my laptop, and if I press any key I simply get the same msg. I turned the system off for a few minutes to make sure it was a good cold boot, but every time I still get the same msg. I tried switching the BIOS setting from IDE to AHCI (IDE is required for XP to boot, AHCI required for Win 7), but I still get the same error msg before I'm even prompted with the OS boot selection, so it made no difference of course.
I looked up this issue and found various suggestions, but none of the ones I found took into consideration a dual boot config., they were all Win 7 specific solutions. I don't what to try and repair the MBR only to have it screw up my dual boot config and be unable to access XP, which is what I use almost exclusively, nor do i want to lose access to Win 7 if at all possible.
I had a backup HD of my complete system that I saved several months ago when I upgraded my HD, and I periodically refresh the most important files on it, so I'm currently running on the laptop in question using my old HD, and it's working just fine. Worst case I can just clone my old HD to my newer HD that's screwed up, but I'll still lose a lot of changes I've made to the OS since I upgraded the HD and have to reinstall and config a number of programs, so that's my last option. I'll also have to back up about 200GB of data from the newer HD which is much larger than my old HD, and then restore it back after the clone, something that will take a lot of time and unncessary effort if I can just fix the MBR.
I'm having a problem every time I power on the system. I'm dual booting vista ultimate with win 7 build 7100; with vista I have no problem, but with 7 every time I start the system the first boot attempt gives me the error 0xc000000e after the boot manager display: "the boot selection failed because a required device is inaccessible".;after a reset the system boots 7 with no problems. Win 7 is installed in a brand new hd(seagate barracuda 1.5tb) and vista on a second hd.
I've search the web for people with a similar problem with no success. I've tryed already many solutions but the problem persists(latest bios for the motherboard, latest intel sata drivers, etc). I'm hoping that this could be a bug in win 7 instead of a hardware failure for the hd. Again, the strange thing is that this only happen after the power on. After that first error, no matter how many reboots, the system always boot without problems.
i did a terrible mistake. i installed windows 7 first on one drive and then i install windows xp on separate drive. and when i restart there was no boot menu to choose the OS from list only windows xp started straight away. i did not knew about EasyBCD . and i put my windows 7 DVD and run recovery. now i can goto windows 7 but xp is missing again. is there any way i will not install xp from beginning and windows 7 can add boot menu in startup to choose xp or 7.
View 4 Replies View RelatedI recently added a hard drive to my computer (SSD), and installed Windows 7 x64 onto it. The result being a dual boot system, which by default boots to the SSD, and optionally (by Windows Boot Menu), can be booted to the original drive (standard mechanical drive).
Initial setup went fine, however I decided to customize the Windows Boot Menu, so that logical names could be associated with each operating system instance. To do this I used EasyBCD and I altered the names in the Windows Boot Menu from: Quote: Windows 7 Windows 7 to... Quote: Windows 7 - SSD Windows 7 - Standard Drive Shortly after the modification I noticed that I was no longer able to boot into the original OS. Instead I was being presented with a "Repair Windows" option. Figuring that my EasyBCD "tampering" may have had something to do with the issue I decided to change the names back to "Windows 7" in the Windows Boot Menu. However doing so had no positive impact on boot up of the original OS.
After booting again into the original OS I accepted the "Repair Windows" option, and then left the computer over night to do it's "thing". After completion of the "Repair" the situation has deteriorated -
* Windows doesn't load (the same as before)
* Windows doesn't present a "Repair Windows" option (it did before)
* The computer reboots a short period after the "Starting Windows" screen is presented
As a side note the drive is in good health, and all data on it can be read from within Windows 7 when I boot to the SSD OS.
I have xp 32bit and 7 64bit on a dualboot and 7 is the default, however I want to change that.
View 7 Replies View Related